Search NASA⌕ Search

SEARCH · Search NASA

Results for “CDISC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

On the Coupling of CDISC Design Method with FPX Rotor Code

A rotor section aerodynamics design package is developed by coupling Constrained Direct Iterative Surface Curvature (CDISC) design method with the FPX rotor code. The coupling between the CDISC design and the FPX flow analysis is fully automated. The CDISC design method employs a predictor-corrector procedure iteratively to determine a surface geometry which produces a target pressure distribution, where the target pressure distributions is either pre-defined or automatically generated through flow and geometry constraints. The FPX code is an eXtended Full-Potential rotor Computational Fluid Dynamics (CFD) code, which solves the three-dimensional unsteady full-potential equation in a strong conservative form using an implicit approximate factorization finite-difference scheme with entropy and viscosity corrections. Application of the CDISC design method coupled with the FPX rotor code is made for rotor blades in hovering motions. Several design examples are presented to demonstrate the capability of the new package in rotor section design.

Hu, Hong↗
NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag reduction technology with potential fuel-burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D-ME flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar-flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this observed benefit, future work is motivated to design a cruise slotted wing with laminar flow on both wing elements to achieve a significant reduction in cruise drag while delaying drag divergence.

CDISC↗
NASA NTRSDate not supplied

Transonic Cruise Slotted Wing Design for Commercial Transport Aircraft using CDISC

A knowledge-based aerodynamic design method, CDISC, has been extended to enable the computational design of transonic cruise slotted wings for commercial transport aircraft. The cruise slotted wing is a multielement wing concept with a forward main element and an aft flap element, separated to form an intermediate slot. This slot favorably redirects airflow from the main element lower surface toward the low-momentum, upper-surface boundary layer of the flap. Relative to the supercritical wing, the cruise slotted wing enables greater aft loading that helps to reduce shock strength and transonic pressure drag. The cruise slotted wing may be considered a passive drag-reduction technology with potential fuel burn savings and increased vehicle range for next-generation aircraft. The current paper seeks to quantify the drag-saving benefits of cruise slotted wing technology in application to single-aisle commercial transport aircraft. A series of multielement design constraints were developed within CDISC for the design of a partial-span, cruise slotted wing for a Mach-0.8 variant of the Common Research Model. To mitigate the skin-friction drag penalty associated with cruise slotted wings, the design features a flap with natural laminar flow over approximately 75% of the flap surface area. Cruise drag estimates from the NASA USM3D flow solver between a supercritical wing and the partial-span, cruise slotted wing design were within one drag count. Near-cruise, off-design analyses showed limited laminar flow sensitivity to angle of attack and a more gradual drag rise compared to a supercritical wing. Based on this demonstrated benefit, future work is motivated to design a cruise slotted wing with natural laminar flow on both wing elements to achieve a significant reduction in cruise drag while providing delayed drag divergence.

CDISC↗
NASA NTRSDate not supplied

Application of the CATNLF Design Method to a Transonic Transport Empennage Using CDISC

A novel Crossflow Attenuated Natural Laminar Flow (CATNLF) design method has been developed to achieve laminar flow on aircraft empennage at transonic flight conditions. This approach has been applied to the design of a nonlifting vertical tail using CDISC, a knowledgebased aerodynamic design tool developed at the NASA Langley Research Center. A horizontal tail was also designed using an enhanced CATNLF design approach for low-lift components. CDISC was coupled with USM3D-ME, a Navier-Stokes computational fluid dynamics solver. Stability and transition software was used to determine the laminar extent on the surfaces. Results indicate laminar flow can be sustained at midcruise conditions to about x/c=0.40 on the vertical tail and as much as x/c=0.65 on the horizontal tail lower surface. Transonic longitudinal off-design analysis indicates minimal change in the laminar extent. However, nonzero sideslip angles at transonic conditions can cause premature transition relative to the midcruise condition.

Brent W. Pomeroy↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF) flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight test is anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced the F-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRSDate not supplied

Progress Towards the Design of a Natural Laminar Flow Wing for a Low-Boom Concept using CDISC

The X-59 is being developed to evaluate the ability to reduce sonic boom loudness to acceptable levels, with the ultimate goal of enabling supersonic flight overland. If successful, one of the future research challenges will be focused on reducing fuel burn. In this paper, Natural Laminar Flow (NLF) is proposed as a technology to decrease fuel burn for a low-boom configuration. This will require an evaluation of the compatibility of NLF wings for a low-boom configuration. As a first step towards this goal, the CATNLF method was employed using the CDISC design module to perform NLF design on an isolated wing from a low-boom configuration. The results show that the NLF wing features laminar flow over 46% of the wing upper surface, providing a potential 8.3 drag count reduction relative to the design with no laminar flow. Off-design analyses were additionally performed to evaluate the performance of the NLF wing for changes in angle of attack and Mach number. The results showed that the NLF wing offers a performance benefit over the entire range of off-design conditions considered, with most of the laminar flow maintained for near cruise conditions. Future work will consider the full configuration, which will enable an assessment of the impact of the NLF wing design on sonic boom loudness. Additionally, attachment line transition will be addressed, which was predicted to result in a loss of laminar flow on the inboard 50% span for this work. Finally, future research will focus on developing a method for effectively choosing the frequency-beta pairs used for the stability analysis to improve transition prediction and provide a more accurate estimate of the performance benefit.

Supersonic↗
NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗
NASA NTRSDate not supplied

CDISC Remote Design Method to Simulate Aircraft Interference Effects for the CATNLF Flight Test

The Crossflow Attenuated Natural Laminar Flow (CATNLF)flight test is an experimental evaluation of a laminar flow design approach that will be conducted on a small transonic wing-like model suspended from the Centerline Instrumented Pylon (CLIP) underneath an F-15 vehicle. The upcoming flight testis anticipated to provide experimental data that may be useful for transition prediction code calibrations or laminar flow computational studies. For the computational results to be reliable, relevant aerodynamics must be included in the simulations. It has been shown that the F-15 vehicle produces a notable aerodynamic influence on the CATNLF test article, and that removing the F-15 vehicle from the simulation significantly alters the laminar flow behavior. Because the F-15 vehicle is not a publicly-releasable geometry, if the CATNLF flight test dataset is to be widely used by the community, an alternative method to ensure that the CATNLF test article flight configuration aerodynamics is properly modeled is required. The objective of this research is to use the CDISC aerodynamic design tool to perform a remote design of a surface that would replicate the aerodynamic influence on the CATNLF test article. This new design approach, referred to as the Equivalent Loading via Interference Surface Effects (ELISE), is presented in this paper, including the details on the design setup and results. The ELISE design successfully reproduced theF-15 influence on the CATNLF test article, with predicted transition location within an average of 4% chord of the full flight configuration. An off-design assessment is included for small perturbations in Mach and sideslip angle that suggest the ELISE design can cover a reasonable range of expected flight conditions with the same geometry. This paper is intended to explain the design approach, as well as show results that can be expected when utilizing the ELISE design method.

CDISC↗
NASA NTRSDate not supplied

History and Status of the CDISC Aerodynamic Design Method

This paper will review the development and application of the CDISC aerodynamic design method that began in the early 1980s and continues in active use today. The method uses an iterative, knowledge-based approach that has been coupled with numerous flow solvers utilizing a variety of grid types and levels of flow physics. It has been applied to configurations varying in complexity from 2-D airfoils to full 3-D aircraft at flow conditions ranging from low-speed, high-lift to supersonic cruise. The knowledge-based approach provides a very rapid design process, with designs typically completed in approximately 1-2x the time required for an initial converged analysis of the baseline. The evolution of the method as it tracked the expansive growth of grid and flow solver technology, along with some major applications over 5 decades, are given, followed by a description of the philosophy and process used in design. Finally, an example of its use in a preliminary design environment is given.

CDISC↗
NASA NTRSDate not supplied

Progress Towards the Design of a Natural Laminar Flow Wing for a Low-Boom Concept Using CDISC

The X-59 is being developed to evaluate the ability to reduce boom loudness to acceptable levels, with the ultimate goal of enabling supersonic flight overland. If successful, one of the future research challenges will be focused on reducing fuel burn. In this paper, Natural Laminar Flow (NLF) is proposed as a technology to decrease fuel burn for a low-boom configuration. This will require an evaluation of the compatibility of NLF wings for a low-boom configuration. As a first step towards this goal, the CATNLF method was employed using the CDISC design module to perform NLF design on an isolated wing from a low-boom configuration. The results show that the NLF wing features laminar flow over 46\% of the wing upper surface, providing a potential 8.3 drag count reduction relative to the design with no laminar flow. Off-design analyses were additionally performed to evaluate the performance of the NLF wing for changes in angle of attack and Mach number. The results showed that the NLF wing offers a performance benefit over the entire range of off-design conditions considered, with the majority of the laminar flow maintained for near cruise conditions. Future work will consider the full configuration, which will enable an assessment of the impact of the NLF wing design on sonic boom loudness. Additionally, attachment line transition will be addressed, which was predicted to result in a loss of laminar flow on the inboard 50\% span for this work. Finally, future research will focus on developing a method for effectively choosing the frequency-beta pairs used for the stability analysis to improve transition prediction and provide a more accurate estimate of the performance benefit.

Supersonic↗
NASA NTRS2019

A Knowledge-Based Optimization Method for Aerodynamic Design

A new aerodynamic design method, CODISC, has been developed that combines a legacy knowledge-based design method, CDISC, with a simple optimization module known as SOUP. The primary goal of this new design system is to improve the performance gains obtained using CDISC without adding significant computational time. An additional objective of this approach is to reduce the need for a priori knowledge of good initial input variable values, as well as for subsequent manual revisions of those values as the design progresses. Several test cases illustrate the development of the process to date and some of the options available at transonic and supersonic speeds for turbulent flow designs. The test cases generally start from good baseline configurations and, in all cases, were able to improve the performance. Several new guidelines for good initial values for the design variables, as well as new design rules within CDISC itself, were developed from these cases.

SOUP↗
NASA NTRS1999

TLNS3D/CDISC Multipoint Design of the TCA Concept

This paper presents the work done to date by the authors on developing an efficient approach to multipoint design and applying it to the design of the HSR TCA (High Speed Research Technology Concept Aircraft) configuration. While the title indicates that this exploratory study has been performed using the TLNS3DMB flow solver and the CDISC (Constrained Direct Iterative Surface Curvature) design method, the CDISC method could have been used with any flow solver, and the multipoint design approach does not require the use of CDISC. The goal of the study was to develop a multipoint design method that could achieve a design in about the same time as 10 analysis runs.

Campbell, Richard L.↗
NASA NTRS1999

TLNS3D/CDISC Multipoint Design of the TCA Concept

This paper presents the work done to date by the authors on developing an efficient approach to multipoint design and applying it to the design of the HSR TCA configuration. While the title indicates that this exploratory study has been performed using the TLNS3DMB flow solver and the CDISC design method, the CDISC method could have been used with any flow solver, and the multipoint design approach does not require the use of CDISC. The goal of the study was to develop a multipoint design method that could achieve a design in about the same time as 10 analysis runs.

Campbell, Richard L.↗
NASA NTRS2004

Efficient Viscous Design of Realistic Aircraft Configurations

This paper addresses the use of the Constrained Direct Iterative Surface Curvature (CDISC) design method in the aircraft design process. A discussion of some of the requirements for practical use of CFD in the design process is followed by a description of different CFD design methods, along with their relative strengths and weaknesses. A detailed description of the CDISC design method highlights some of the aspects of the method that provide computational efficiency and portability, as well as the flow and geometry constraint capabilities. In addition, an efficient approach to multipoint design, the Weighted Averaging of Geometries (WAG) method, is described and illustrated using a couple of simple examples. The CDISC and WAG methods are then applied to a complex generic business jet geometry using an unstructured grid flow solver to demonstrate the multipoint and multicomponent design capabilities of these methods. Introduction

Campbell, Richard L.↗
NASA NTRS2018

Development of a Knowledge-Based Optimization Method for Aerodynamic Design

A new aerodynamic design method, CODISC, has been developed that combines an existing knowledgebased design method, CDISC, with a simple optimization module known as SOUP. The primary goal of this new design system is to improve the performance gains obtained using CDISC without adding significant computational time. An additional benefit of this approach is a reduction in the need for a priori knowledge of good initial input variable values as well as for subsequent manual revisions of those values as the design progresses. A series of 2D and 3D test cases are used to illustrate the development of the process and some of the options available at transonic and supersonic speeds for both laminar and turbulent flow. The test cases start from good baseline configurations and, in all cases, were able to improve the performance. Several new guidelines for good initial values for the design variables, as well new design rules within CDISC itself, were developed from these cases.

Campbell, Richard L.↗