Search NASA⌕ Search

SEARCH · Search NASA

Results for “CIRCULAR CYLINDER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1945

On the circulatory subsonic flow of a compressible fluid past a circular cylinder

The circulatory subsonic flow around an infinite circular cylinder is computed using the linearized pressure-volume relation, by a method developed in a previous report. Formulas and graphs are given for the velocity and pressure distributions, the circulation, the lift, and the dependence of the critical Mach number upon the position of the stagnation point.

FLOW, COMPRESSIBLE-MEASUREMENT↗
NASA NTRS1983

Vortex motion behind a circular cylinder

Vortex motion behind a circular cylinder moving through water is discussed. It is shown that a pair of vortices form behind a moving cylinder and that their centers will move along a predictable curve. This curve represents an equilibrium condition which, however, is subject to perturbation. The stability of the vortex pair is investigated. Movement of the vortex pair away from the cylinder is calculated as an explanation of the resistance of the cylinder. Finally, the principles elaborated are applied to the flow around a flat plate.

Foeppl, L.↗
NASA NTRS1984

Steady viscous flow past a circular cylinder

Viscous flow past a circular cylinder becomes unstable around Reynolds number Re = 40. With a numerical technique based on Newton's method and made possible by the use of a supercomputer, steady (but unstable) solutions have been calculated up to Re = 400. It is found that the wake continues to grow in length approximately linearly with Re. However, in conflict with available asymptotic predictions, the width starts to increase very rapidly around Re = 300. All numerical calculations have been performed on the CDC CYBER 205 at the CDC Service Center in Arden Hills, Minnesota.

Fornberg, B.↗
NASA NTRS1943

Some Investigations of the General Instability of Stiffened Metal Cylinders IV : Continuation of Tests of Sheet-covered Specimens and Studies of the Buckling Phenomena of Unstiffened Circular Cylinders

This is the fourth of a series of reports covering an investigation of the general instability problem by the California Institute of Technology. The first five reports of this series cover investigations of the general instability problem under the loading conditions of pure bending and were prepared under the sponsorship of the Civil Aeronautics Administration. The succeeding reports of this series cover the work done on other loading conditions under the sponsorship of the National Advisory Committee for Aeronautics. This report is to deal primarily with the continuation of tests of sheet-covered specimens and studies of the buckling phenomena of unstiffened circular cylinders.

CYLINDERS, STEEL↗
NASA NTRS1990

Patterns of vortex shedding from an oscillating circular cylinder

Vortex shedding from an oscillating circular cylinder was numerically investigated at Re = 100 with the Navier-Stokes equations and the new boundary conditions. The detailed shedding patterns are characterized by means of streakline plotting and lift-coefficient curves. A parameter map is presented which distinguishes the synchronized shedding from the asynchronous and the double vortices shedding from the single vortex shedding. The computational result is in good agreement with earlier experimental results.

Chang, Keun-Shik↗
NASA NTRS1960

Effect of Reynolds Number on the Force and Pressure Distribution Characteristics of a Two-Dimensional Lifting Circular Cylinder

A two-dimensional lifting circular cylinder has been tested over a Mach number range from 0.011 to 0.32 and a Reynolds number range from 135,000 to 1,580,000 to determine the force and pressure distribution characteristics. Two flaps having chords of 0.37 and 6 percent of the cylinder diameter, respectively, and attached normal to the surface were used to generate lift. A third configuration which had 6-percent flaps 1800 apart was also investigated. All flaps were tested through a range of angular positions. The investigation also included tests of a plain cylinder without flaps. The lift coefficient showed a wide variation with Reynolds number for the 6-percent flap mounted on the bottom surface at the 50-percent-diameter station, varying from a low of about 0.2 at a Reynolds number of 165,000 to a high of 1.54 at a Reynolds number of 350,000 and then decreasing almost linearly to a value of 1.0 at a Reynolds number of 1,580,000. The pressure distribution showed that the loss of lift with Reynolds number above the critical was the result of the separation point moving forward on the upper surface. Pressure distributions on a plain cylinder also showed similar trends with respect to the separation point. The variation of drag coefficient with Reynolds number was in direct contrast to the lift coefficient with the minimum drag coefficient of 0.6 occurring at a Reynolds number of 360,000. At this point the lift-drag ratios were a maximum at a value of 2.54. Tests of a flap with a chord of 0.0037 diameter gave a lift coefficient of 0.85 at a Reynolds number of 520,000 with the same lift-drag ratio as the larger flap but the position of the flap for maximum lift was considerably farther forward than on the larger flap. Tests of two 6-percent flaps spaced 180 deg apart showed a change in the sign of the lift developed for angular positions of the flap greater than 132 deg at subcriti- cal Reynolds numbers. These results may find use in application to air- craft using forebody strakes. The drag coefficient developed by the flaps when normal to the relative airstream was approximately equal to that developed by a flat plate in a similar attitude.

Lockwood, Vernard E.↗
NASA NTRS1937

Bending Tests of Circular Cylinders of Corrugated Aluminum-alloy Sheet

Bending tests were made of two circular cylinders of corrugated aluminum-alloy sheet. In each test failure occurred by bending of the corrugations in a plane normal to the skin. It was found, after analysis of the effect of short end bays, that the computed stress on the extreme fiber of a corrugated cylinder is in excess of that for a flat panel of the same basic pattern and panel length tested as a pin-ended column. It is concluded that this increased strength was due to the effects of curvature of the pitch line. It is also concluded from the tests that light bulkheads closely spaced strengthen corrugated cylinders very materially.

STRESSED SKIN - CYLINDERS, CIRCULAR - BENDING↗
NASA NTRS1974

Application of wave mechanics theory to fluid dynamics problems: Boundary layer on a circular cylinder including turbulence

The application of the elements of quantum (wave) mechanics to some special problems in the field of macroscopic fluid dynamics is discussed. Emphasis is placed on the flow of a viscous, incompressible fluid around a circular cylinder. The following subjects are considered: (1) the flow of a nonviscous fluid around a circular cylinder, (2) the restrictions imposed the stream function by the number of dimensions of space, and (3) the flow past three dimensional bodies in a viscous fluid, particularly past a circular cylinder in the symmetrical case.

Krzywoblocki, M. Z. V.↗