Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONVERGENT-DIVERGENT NOZZLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Thrust and drag characteristics of a convergent-divergent nozzle with various exhaust jet temperatures

An investigation was conducted in the 8-by-6 foot supersonic wind tunnel on the effect of exhaust-gas temperatures on the external and internal characteristics of a convergent-divergent nozzle having an area expansion ratio of 1.83. Data were obtained over a pressure-ratio range from 1 to 20 at free-stream Mach numbers of 1.6 and 2.0 for exhaust temperatures of 860 degrees, 1650 degrees, and 2000 degrees R. Results of this investigation indicated that generally both the internal and external performance characteristics were only slightly affected by a large change in jet temperature. The small differences in performance which did occur were predicted satisfactorily from theoretical considerations.

Hearth, Donald P↗
NASA NTRS1956

Internal performance characteristics of short convergent-divergent exhaust nozzles designed by the method of characteristics

Internal performance data on a short exhaust nozzle designed by the method of characteristics were obtained over a range of pressure ratios from 1.5 to 22. The peak thrust coefficient was not affected by a shortened divergent section, but it occurred at lower pressure ratios due to reduction in expansion ratio. This nozzle contour based on characteristics solution gave higher thrust coefficients than a conical convergent-divergent nozzle of equivalent length. Abrupt-inlet sections permitted a reduction in nozzle length without a thrust-coefficient reduction.

Krull, H George↗
NASA NTRS1954

Thrust characteristics of a series of convergent-divergent exhaust nozzles at subsonic and supersonic flight speeds

An experimental investigation of a series of four convergent-divergent exhaust nozzles was conducted in the Lewis 8-by-6 foot supersonic wind tunnel at Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a range of nozzle pressure ratios. The thrust characteristics of these nozzles were determined by a pressure-integration technique. From a thrust standpoint, a nozzle designed to give uniform parallel flow at the exit had no advantage over the simple geometric design with conical convergent and divergent sections. The rapid-divergent nozzles might be competitive with the more gradual-divergent nozzles since the relatively short length of these nozzles would be advantageous from a weight standpoint and might result in smaller thrust losses due to friction. The thrusts, with friction losses neglected, were predicted satisfactorily by one-dimensional theory for the nozzles with relatively gradual divergence. The thrusts of the rapid-divergent designs were several percentages below the theoretical values at the design pressure ratio or above, while at low pressure ratios there was a considerable effect of free-stream Mach number, with thrusts considerably above theoretical values at subsonic speeds and somewhat above theoretical values at supersonic speeds. This Mach numb effect appeared to be related to the variation of the model base pressure with free-stream Mach number.

Fradenburgh, Evan A↗
NASA NTRS1954

Preliminary Investigation of Performance of Variable-throat Extended-plug-type Nozzles over Wide Range of Nozzle Pressure Ratios

As part of an overall program for the experimental investigation of large-scale jet nozzles, a preliminary evaluation of the internal performance characteristics of several variable-throat extended-plug-type nozzles was obtained over a range of nozzle pressure rations from 2 to 15 with nozzle throat variations as great as 2:1. The extended-plug nozzle attained peak thrust coefficients as high as those which have been attained with fixed-geometry convergent-divergent nozzles. The thrust coefficients of the extended-plug nozzles were relatively insensitive to both nozzle pressure ratio and throat area over the range investigated. The lack of sensitivity of thrust coefficient to nozzle pressure ratio and throat area was due primarily to the absence of severe decreases in thrust coefficient, which are normally observed at low nozzle pressure ratios for convergent-divergent nozzles because of overexpansion. For choked flow, the flow coefficients of the extended-plug nozzles varied from 0.95 to 0.997. A ratio of the outer-shell exit area to nozzle throat area was found to be an important variable affecting nozzle performance. Most of the configurations reported herein showed a small decrease in thrust coefficient at low nozzle pressure ratios; however, it is believed that this characteristic can nearly be eliminated by proper nozzle design.

NOZZLES↗
NASA NTRS1954

Investigation of Thrust and Drag Characteristics of a Plug-type Exhaust Nozzle

An investigation was conducted in the 8- by 6-foot supersonic wind tunnel on the external and internal characteristics of a plug-type exhaust nozzle. Two positions of the center plug, one simulating a convergent nozzle and the other a convergent-divergent nozzle, were investigated. Data were obtained at free-stream Mach numbers of 0.1, 0.6, 1.6, and 2.0 over a pressure-ratio range of 1 to 20 and angles of attack of zero and 8 degrees. Results of this investigation indicated that the plug nozzle had thrust-minus-drag performance over the entire pressure-ratio range comparable with equivalent conventional nozzles. The effect of the exhaust jet on the external aerodynamics was similar to results observed for conventional nozzles. In addition, the thrust characteristics were generally insensitive to external flow and good agreement was noted with data obtained on comparable plug nozzles in quiescent air.

Hearth, Donald P↗
NASA NTRS1948

Internal-Film Cooling of Rocket Nozzles

Experiments were conducted with 1000-pound-thrust rocket engine to determine feasibility of cooling convergent-divergent nozzle by internal film of water introduced at nozzle entrance. Water flow of 3 percent of propellant flow reduced heat flow into nozzle to 55 percent of uncooled heat flow. Introduction of water by porous ring before nozzle resulted in more uniform coverage of nozzle than water introduced by single arrangement of 36 jets directed along nozzle wall. Water flow through porous ring of 3.5 percent of propellant flow stabilized wall temperature in convergent section but did not adequately cool throat or divergent sections.

HEAT TRANSFER↗
NASA NTRS1951

Velocity and Temperature Fields in Circular Jet Expanding from Choked Nozzle into Quiescent Air

The Mach number and temperature profiles in jets expanding from convergent and convergent-divergent nozzles are presented for several values of nozzle-exit pressure ratio. The effects of jet temperature, Reynolds number, and humidity on jet spreading are briefly evaluated. The results indicated that the downstream Mach number profiles for a heated jet are slightly narrower than those for a unheated jet, whereas the downstream temperature profiles were unaffected by nozzle temperature change, and that the effects of Reynolds number and humidity were negligible.

FLOW, SUPERSONIC↗
NASA NTRS1952

Investigation at Mach Number 1.91 of Spreading Characteristics of Jet Expanding from Choked Nozzles

It is demonstrated that the temperature profiles of jets expanding into a supersonic stream are considerably smaller than the temperature profiles of jets expanding into quiescent air. The effect on the wake of varying afterbody geometry is shown to be small. The gross spreading characteristics of jets expanding from convergent and convergent-divergent nozzles in the base of a body of revolution with various boattail configurations at a Mach number of 1.91 are presented.

EXITS↗
NASA NTRS1954

Effect of Jet-nozzle-expansion Ratio on Drag of Parabolic Afterbodies

The interaction of the flow from one convergent and two convergent-divergent nozzles on parabolic afterbodies was studied at free-stream Mach numbers of 2.0, 1.6, and 0.6 over a range of jet pressure ratio. The influence of the jet on boattail and base drag was very pronounced. Study of the total external afterbody drag values at supersonic speeds indicated that, over most of the high-pressure-ratio range, increasing the nozzle design expansion ratio increased the drag even though the boattail area was reduced. Increasing the pressure ratio tended to increase slightly the total-drag increment caused by angle-of-attack operation.

Englert, Gerald W↗
NASA NTRS1953

Analysis of the turbojet engine for propulsion of supersonic fighter airplanes / David S. Gabriel, Richard P. Krebs, E.Clinton Wilcox, Stanley L.Koutz

An analytical investigation was made of two supersonic interceptor type airplanes to determine the most desirable turbojet engine characteristics for this application The airplanes were designed differently primarily because of the amount of subsonic flight incorporated in the flight plan--one flight having none and the other, a cruise radius of 400 nautical miles. Several power plant design variables were varied independently to determine the effect of changes in each parameter on airplane performance. These parameters included compressor pressure ratio, compressor efficiency, turbine-inlet temperature, afterburner temperature, engine specific weight, and air-handling capacity. The effects of using a convergent-divergent exhaust nozzle and of changing the design flight Mach number were also investigated.

ENGINES, TURBOJET↗
NASA NTRS1956

The Compressible Laminar Boundary Layer with Heat Transfer and Arbitrary Pressure Gradient

An approximate method for the calculation of the compressible laminar boundary layer with heat transfer and arbitrary pressure gradient, based on Thwaites' correlation concept, is presented. With the definition of dimensionless shear and heat-transfer parameters and an assumed correlation of these parameters in terms of a momentum parameter, a complete system of relations for calculating skin friction and heat transfer results. Knowledge of velocity or temperature profiles is not necessary in using this calculation method. When the method is applied to a convergent-divergent, axially symmetric rocket nozzle, it shows that high rates of heat transfer are obtained at the initial stagnation point and at the throat of the nozzle. Also indicated are negative displacement thicknesses in the convergent portion of the nozzle; these occur because of the high density within the lower portions of the cooled boundary layer. (author)

Cohen, Clarence B↗