Search NASA⌕ Search

SEARCH · Search NASA

Results for “COPPER CHLORIDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Electronic properties of carbon fibers intercalated with copper chloride

Copper chloride intercalated pitch-based carbon fibers are found to have electrical resistivities as low as 12.9 micro-ohm-cm, and are air- and thermally-stable at and above room temperature. This is therefore a good candidate system for conductor application. In addition, Shubnikov-deHaas quantum oscillatory effects were found, and electronic properties of the intercalated fiber are studied using magnetic fields to 20 tesla.

Oshima, H.↗
NASA NTRS1990

Copper Chloride Cathode For Liquid-Sodium Cell

Rechargeable liquid-sodium cell with copper chloride cathode offers substantial increase in energy density over cells made with other cathode materials. Unit has theoretical maximum energy density of 1135 W.h/kg. Generates electricity by electrochemical reaction of molten sodium and solid copper chloride immersed in molten electrolyte, sodium tetrachloroaluminate at temperature of equal to or greater than 200 degrees C. Wall of alumina tube separates molten electrolyte from molten sodium anode. Copper chloride cathode embedded in pores of sintered nickel cylinder or directly sintered.

Bugga, Ratnakumar V.↗
NASA NTRS1973

Double-discharge copper vapor laser with copper chloride as a lasant

A copper vapor laser utilizing copper chloride as a lasant in a heated discharge tube has been studied. The lasing action was observed only when two successive discharge current pulses at suitable time intervals were applied. The first pulse is considered to be a dissociation pulse to produce copper and chlorine atoms; the second to be a pumping pulse to produce population inversion. The maximum energy density measured to date was 17 microjoule/cu cm.

Chen, C. J.↗
NASA NTRS1982

Metallic conductivity and air stability in copper chloride intercalated carbon fibers

Carbon-copper chloride intercalation compounds have been obtained by using variously graphitized carbon fibers as host materials. The resultant conductors are air stable, thermally stable to 450 K, have electrical resistivities as low as 12.9 microohm cm at room temperature, and have metallic conductivity temperature dependencies. These intercalated fibers have tensile strengths of 160000 psi, and Young's moduli of 25 x 10 to the 6th psi. For aerospace use, 1/(resistivity x density) is a figure of merit. On this basis, a reduction in resistivity by a factor of two will make this conductor competitive with copper.

Oshima, H.↗
NASA NTRS1990

Copper chloride cathode for a secondary battery

Higher energy and power densities are achieved in a secondary battery based on molten sodium and a solid, ceramic separator such as a beta alumina and a molten catholyte such as sodium tetrachloroaluminate and a copper chloride cathode. The higher cell voltage of copper chloride provides higher energy densities and the higher power density results from increased conductivity resulting from formation of copper as discharge proceeds.

Bugga, Ratnakumar V.↗
NASA NTRS1977

A parametric study of the copper chloride laser

A parametric study of the double-pulsed copper chloride laser is reported. The effects of a wide range of variables on the laser energy density and on three characteristic time intervals (the minimum, maximum, and optimum delay time) between the two electrical-discharge pulses were studied. The geometric variables investigated included a tube diameter of 2.3 to 40 mm and a tube length of 3 to 60 cm. Three buffer gases, helium, neon, and argon, were studied over the pressure range 0.5-50 torr, and the tube temperature was varied from 270 to 500 C. The energy density and voltage of both the dissociation and pumping pulse were varied independently from less than 1 mJ/cu cm at 8.5 kV to over 500 mJ/cu cm at 20 kV. The optimum conditions for maximum laser energy density were found to be with 20 torr neon in a 10-mm by 30-cm tube at 400 C. The maximum energy density obtained was 22 microjoules/cu cm.

Nerheim, N. M.↗
NASA NTRS1986

Graphite fiber intercalation: Basic properties of copper chloride intercalated fibers

In situ resistance measurements were used to follow the intercalation of copper chloride in pitch-based fibers. Subsequent single fiber resistivity measurements reveal a large range of resistivities, from 13 to 160 micro-ohms cm. Additional density measurements reveal a bimodal distribution of mass densities. The dense fibers have lower resistivities and correspond to the stage III compound identified by X-ray diffraction. Neither resistivity nor density correlate with diameter. Both energy dispersive spectroscopy and mass density data suggest that excess chlorine resides in the intercalated fiber, resulting in a stoichiometry of C4.9n CuCl2.5 (where n is the stage number) for the denser fibers. Finally, thermogravimetric analysis shows a 33 percent loss in mass upon heating to 700C. This loss in mass is attributed to loss of both chlorine and carbon.

Jaworske, D. A.↗
NASA NTRS1977

Measurements of copper ground-state and metastable level population densities in a copper-chloride laser

The population densities of both the ground and the 2D(5/2) metastable states of copper atoms in a double-pulsed copper-chloride laser are correlated with laser energy as a function of time after the dissociation current pulse. Time-resolved density variations of the ground and excited copper atoms were derived from measurements of optical absorption at 324.7 and 510.6 nm, respectively, over a wide range of operating conditions in laser tubes with diameters of 4 to 40 mm. The minimum delay between the two current pulses at which lasing was observed is shown to be a function of the initial density and subsequent decay of the metastable state. Similarly, the maximum delay is shown to be a function of the initial density and decay of the ground state.

Nerheim, N. M.↗
NASA NTRS1977

Addition of HCl to the double-pulse copper chloride laser

Addition of small amounts of hydrogen chloride to the buffer gas of a double-pulse CuCl laser causes an increase in the production of copper atoms in the ground state. A maximum laser energy increase of 15% was observed and the span of delay times for which laser action occurred increased.

Vetter, A. A.↗
NASA NTRS1977

Quantitative effect of initial current rise on pumping the double-pulsed copper chloride laser

The laser energy at optimum time delay of a double-pulsed CuCl laser was experimentally determined to be a logarithmic function of the initial current rise of the pumping pulse over the total circuit inductance range 1 to 12 microhenrys. The minimum delay was found to decrease with initial current rise, which implies that faster rising current pulses are more efficient at pumping copper atoms from the ground state to the upper laser level because lasing threshold occurs with a higher population in the lower laser level.

Vetter, A. A.↗
NASA NTRS1978

Scaling a double-pulsed copper chloride laser to 10 mJ

By use of low-inductance (0.5micro H) discharge circuits, pulses of 9.6 mJ were obtained from a double-pulsed CuCl laser. An oscillator-amplifier configuration produced a pulse energy of 11 mJ. Scaling studies indicate that additional increases in the laser energy could be obtained by increasing the discharge voltage above 20 kV and/or by increasing the laser-tube dimensions.

Nerheim, N. M.↗
NASA NTRS1981

Powerful copper chloride laser

Two design innovations give up to thirtyfold increase in power in 300 W laser amplifier. Heat is removed by flowing lasing gas through system, allowing larger lasing volumes. Fast, uniform excitation discharges are obtained with transverse, rather than longitudinal, electrodes.

Pivirotto, T. J.↗
NASA NTRS1982

Method and apparatus for convection control of metallic halide vapor density in a metallic halide laser

An apparatus is disclosed in which a reservoir containing copper chloride is heated so that the copper chloride is maintained in a liquid form. The apparatus includes a means for flowing a buffer gas (which in the exemplary embodiment is neon) over the liquid copper chloride to provide a mixture of copper chloride vapor and neon above the liquid copper chloride. A conduit provides fluid communication between the reservoir containing the copper chloride vapor/neon mixture and the laser. The copper chloride vapor density in the laser is related to the liquid copper chloride temperature and the neon flow rate through the reservoir. In accordance with a further feature of the exemplary embodiment, neon is also provided directly to the laser in order to provide a further means of controlling the copper chloride vapor density in the laser.

Pivirotto, T. J.↗
NASA NTRS1982

High power metallic halide laser

A laser amplification system is disclosed whereby a metallic halide vapor such as copper chloride is caused to flow through a laser amplifier and a heat exchanger in a closed loop system so that the flow rate is altered to control the temperature rise across the length of the laser amplifier. The copper atoms within the laser amplifier should not exceed a temperature of 3000 K, so that the number of copper atoms in the metastable state will not be high enough to prevent amplification in the amplifier. A molecular dissociation apparatus is provided at the input to the laser amplifier for dissociating the copper chloride into copper atoms and ions and chlorine atoms and ions. The dissociation apparatus includes a hollow cathode tube and an annular ring spaced apart from the tube end. A voltage differential is applied between the annular ring and the hollow cathode tube so that as the copper chloride flows through, it is dissociated into copper and chlorine ions and atoms.

Pivirotto, T. J.↗
NASA NTRS1987

Stability of bromine, iodine monochloride, copper (II) chloride, and nickel (II) chloride intercalated pitch-based graphite fibers

Four different grades of pitch-based graphite fibers (Amoco P-55, P-75, P-100. and P-120) were intercalated with each of four different intercalates: bromine (Br2), iodine monochloride (ICl), copper (II) chloride (CuCl2), and nickel (II) chloride (NiCl2). The P-55 fibers did not react with Br2 or NiCl2, and the P-75 did not react with NiCl2. The stability of the electrical resistance of the intercalated fibers was monitored over long periods of time in ambient, high humidity (100 percent at 60 C), vacuum (10 to the -6 torr), and high temperature (up to 400 C) conditions. Fibers with lower graphitization form graphite intercalation compounds (GIC's) which are more stable than those with higher graphitization (i.e., P-55 (most stable) greater than P-75 greater than P-100 greater than P-120 (least stable). Br2 formed the most stable GIC's followed in order of decreasing stability by ICl, CuCl2, and NiCl2. While Br2 GIC's had the most stability, ICl had the advantages of forming GIC's with slightly greater reduction in resistance (by about 10%) than Br2, and the ability to intercalate P-55 fiber. Transition metal chlorides are susceptible to water vapor and high temperature. The stability of fibers in composites differs.

Gaier, James R.↗
NASA NTRS1983

Low frequency dielectric relaxation in boracites

In order to elucidate the nature of the imperfections which adversely affect pyroelectric processes in boracites, the thermal and dispersive characteristics of the low frequency dielectric response in iron-iodide boracite (Fe3B7O13I) and copper-chloride boracite (Cu3B7O13Cl) have been investigated. These characteristics were measured as a function of crystallographic orientation and applied field in both the ferroelectric and paraelectric states. The low frequency dielectric relaxation of 100 line oriented multi-domain copper-chloride boracite clearly indicates the dipole nature of the lattice imperfections. The activation energies calculated from a noninteracting Debye model, are 0.53 eV in the ferroelectric phase and 0.10 eV in the paraelectric phase.

Kim, Q.↗