Experimental invalidation of phase-transition-induced elastic softening in CrN
Abstract not provided
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided
Explore the source record for details and available documents.
Chromium nitride (CrN) films were deposited on Si wafers by arc ion plating at various negative bias voltages and several groups of N{sub 2}/Ar gas flux ratios and chamber gas pressures. The authors systematically investigated the influence of negative bias voltage on the synthesis, composition, microstructure, and properties of the arc ion plating (AIP) CrN films. In this article, the authors investigated the influence of negative bias voltage on the chemical composition, structure, and mechanical properties of the CrN films. The results showed that the chemical composition and phase structure of the AIP CrN films were greatly altered by application of negative bias voltage. Due to the selective resputtering effect, substoichiometric CrN films were obtained. With increase in bias voltages, the main phases in the films transformed from Cr+CrN to Cr{sub 2}N at low N{sub 2}/Ar flow ratios, whereas the films at high N{sub 2}/Ar flow ratios retained the CrN phase structure. The CrN films experienced texture transformation from CrN (200) to CrN (220), and Cr{sub 2}N (300) to Cr{sub 2}N(300)+Cr{sub 2}N(110). Increase in negative bias voltage also resulted in microstructure evolution of coarse columnar grains{yields}fine columnar grains{yields}quasiamorphous microstructure{yields}recrystallized structures. From the experimental results, the authors proposed a new structure zone model based on enhanced bombardment of incident ions by application of negative bias voltage. The influence of negative bias voltage on the microhardness and residual stresses of the films and the inherent mechanisms were also explored.
Structural phase transition is studied in high quality CrN thin films grown by molecular beam epitaxy on MgO(001) substrates. Cross-sectional transmission electron microscopy and x-ray diffraction reveal that the epitaxial relationship between CrN film and MgO substrate is [100] CrN /[100] MgO , [110] CrN /[110] MgO , and [001] CrN /[001] MgO . The films show tensile strain/compression at the CrN/MgO(001) interface, which relaxes gradually with the film growth. Temperature dependent x-ray diffraction measurements show a first-order structural phase transition. In addition to the experimental measurements, first-principles theoretical calculations have been carried out for finding a stable model for the CrN/MgO interface. Furthermore, these calculations determine two possible models for the interface, where a monolayer of chromium oxide is formed between the CrN and MgO layers.
We report the structural and electrical transport studies on CrN{sub 1-x} (CrN) thin films with varying of N{sub 2} flow (5 – 25 SCCM) in an Argon environment of 25 SCCM. CrN thin films were grown at 600°C, in a multi chamber vacuum system at working pressure of 1×10{sup −2} Torr, under the base pressure of 1×10{sup −7} Torr. Structural and electrical transport measurements were carried out using X-ray diffraction (XRD), atomic force microscopy (AFM) and SQUID magnetometer, respectively. XRD (θ-2θ, ω-2θ, and ω) patterns on CrN thin films revealed a structural phase transition which is associated with the lattice parameter variation from 4.136 to 4.168 Å. The temperature dependent resistivity measurements on CrN/MgO(001) showed a clear change in slope at ≈280 K which confirms the magneto-structural transition of CrN from paramagnetic rock salt face-centered-cubic (FCC) to antiferromagnetic orthorhombic structure.
The transport properties of CrN thin films deposited on sapphire have been tailored through structural modifications induced by cumulative argon implantation. As-grown samples experience the typical structural transition in CrN films from orthorhombic at low temperature to cubic above the Néel temperature (≈280 K) and exhibit a metallic-like conduction in both phases. With increasing implantation dose, the conduction mode shifts to a semiconductor-like behavior in both phases, albeit at different damage levels. Analysis of the results suggests that hopping conduction becomes dominant beyond a given damage threshold. The results highlight a promising correlation between defect engineering and conduction mechanisms, offering valuable insights into the versatile electrical properties of CrN films. These implantation-induced defects scatter carriers, leading to a decrease in their mobility. As the implantation dose increases, the defect landscape evolves, modifying the density of states. However, up to a dose of 0.050 dpa, no significant influence on phonon scattering is observed. This approach demonstrates that ion implantation enables precise tuning of CrN's electrical properties without affecting thermal conductivity, offering valuable insights into defect engineering in transition metal nitrides and underscoring its potential for transport properties decorrelation.
The objective of the present paper is to study the influence of the substrate bias voltage on the microstructure, composition, deposition rate, tribological and corrosion properties of CrN coatings obtained by DC magnetron sputtering on 90CrMoV8 steel and Si (100) substrates. The substrate bias voltage varied from 0 to − 700 V. The deposited films were characterized by SEM, XRD and potentiodynamic polarization. The wear behavior and coefficient of friction were determined and investigated after rotative tribometer tests. The results indicated that the substrate bias voltage considerably affected the intrinsic properties of the CrN films. Indeed, it significantly influenced the grain size and the root-mean-squared roughness which varied from 20 to 29 nm, and from 9 to 19 nm, respectively, when polarization changed from 0 to − 700 V. All the CrN coatings have a dense columnar structure and are well crystallized according to the XRD analyses. Nevertheless, it has been shown that the peaks intensity decreased by increasing the substrate bias voltage. By applying a substrate bias voltage, it was obvious that the friction behavior was enhanced, and the wear volume was decreased. Finally, the CrN coating obtained under a substrate bias voltage of − 500 V presented the best corrosion resistance and wear resistance probably due to its dense microstructure.
Here, we report synthesis of single-crystal VN and CrN through high-pressure ionexchange reaction routes. The final products are stoichiometric and have crystallite sizes in the range of 50-120 mu m. We also prepared VN and TiN crystals using high-pressure sintering of nitride powders. On the basis of single-crystal indentation testing, the determined asymptotic Vickers hardness for TiN, VN, and CrN is 18 (1), 10 (1), and 16 (1) GPa, respectively. Moreover, the relatively low hardness in VN indicates that the metallic bonding prevails due to the overfilled metallic a bonds, although the cation-anion covalent hybridization in this compound is much stronger than that in TiN and CrN. All three nitrides are intrinsically excellent metals at ambient pressure. In particular, VN exhibits superconducting transition at T-c approximate to 7.8 K, which is slightly lower than the reported values for nitrogen-deficient or crystallinedisordered samples due to unsuppressed "spin fluctuation" in the well-crystallized stoichiometric VN. The magnetostructural transition in CrN correlates with a metal metal transition at T-N = 240(5) K and is accompanied by a similar to 40% drop in electrical resistivity. Additionally, more detailed electronic properties are presented with new insights into these nitrides.
Cyclic nanoindentation tests were carried out to study the influence of the chromium nitride thin films on the mechanical properties of Zr-based metallic glass. Chromium nitride thin coatings have been deposited on Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate by RF sputtering. The deposition process was done at room temperature under nitrogen reactive gas using a metallic chromium target. The CrN films have a thickness of 300 nm. Several cyclic nanoindentation measurements were conducted on CrN films and Zr{sub 50}Cu{sub 40}Al{sub 10} metallic glass substrate samples at various loading rate values. We have found that the coated metallic glass sample shows high mechanical properties such as hardness and reduced elastic modulus. Cyclic nanoindentation results show a hardening behaviour for these CrN coatings. Moreover, the CrN coated on Zr-based metallic glass was found to have a high value of resistance to crack propagation, as being analysed through the SEM pictures of the residual Vickers indentation impressions.
In this work, three kinds of Cr-based nitride coatings such as monolithic CrN, CrSiN coatings, and multilayered CrSiN/AlN coating with bilayer period of 3.0 nm were deposited on both Si (100) wafer and AISI H13 steel substrates by unbalanced magnetron sputtering. Thermal stability of these coatings was evaluated by annealing the coatings at temperatures between 600 and 1000 degree sign C for 30 min in air. In addition, the corrosion behaviors of these coatings were investigated by potentiodynamic polarization tests in a deaerated 3.5 wt. % NaCl solution at 40 degree sign C. Results from annealing test show the monolithic CrN and CrSiN coatings were completely oxidized after annealed at 800 and 900 degree sign C, and their cross sectional images and atomic force microscopy showed a loose and very porous morphology due to the oxidation. Also, the hardness values of the monolithic CrN and CrSiN coatings were decreased significantly from 22 and 27 GPa to 8 and 14 GPa, respectively. However, the multilayered CrSiN/AlN coating still exhibited a dense microstructure without visible change after annealed at 1000 degree sign C, and moreover, the relatively high hardness of 25 GPa was maintained. The superior thermal stability of the CrSiN/AlN multilayer coating could be attributed to the formation of the dense and stable oxidation barrier consisted of the Al{sub 2}O{sub 3}, Cr{sub 2}O{sub 3}, and amorphous SiO{sub 2} phases near the surface region, which retard the diffusion of oxygen into the coating. In the potentiodynamic polarization test results, it was found that the significantly improved corrosion resistance of the multilayered CrSiN/AlN coating was observed in comparison with those from the monolithic CrN and CrSiN coatings, and its corrosion current density (i{sub corr}) and protective efficiency were measured to be approximately 4.21 {mu}A/cm{sup 2} and 95%, respectively.
Chromium nitride (CrN) films were deposited on Si wafers by arc ion plating (AIP) at various negative bias voltages and several groups of N{sub 2}/Ar gas flux ratios and chamber gas pressures. The authors systematically investigated the influence of negative bias voltage on the synthesis, composition, microstructure, and properties of the AIP CrN films. In this part (Part I), the investigations were mainly focused on the macroparticle distributions and film-growth characteristics. The results showed that macroparticle densities on the film surfaces decreased greatly by applying negative bias voltage, which can be affected by partial pressure of N{sub 2} and Ar gases. From the statistical analysis of the experimental results, they proposed a new hybrid mechanism of ion bombardment and electrical repulsion. Also, the growth of the AIP CrN films was greatly altered by applying negative bias voltage. By increasing the bias voltage, the film surfaces became much smoother and the films evolved from apparent columnar microstructures to an equiaxed microstructure. The impinging high-energy Cr ions accelerated by negative bias voltages were deemed the inherent reason for the evolution of growth characteristics.
Ammonia is a promising alternative to hydrogen with high energy density and favorable storage and transport characteristics. However low flammability and a propensity for high nitrogen oxide (NOx) emissions make direct utilization challenging. Recently, two-stage rich-quench-lean (RQL) combustion strategies have shown promise in achieving low NOx emissions with ammonia. In this approach, the rich stage serves to oxidize a portion of the fuel, while thermally decomposing as much of the remaining ammonia as possible, generating hydrogen. In the second (lean) stage, air is rapidly introduced, burning out the hydrogen and residual ammonia. Two-stage RQL combustion of ammonia has been investigated in the open literature both experimentally and numerically. In general, idealized chemical reactor network (CRN) models predict NOx concentrations below that of 2D/3D computational fluid dynamics models and experiments. The primary drivers of these discrepancies may be largely attributed to finite rate mixing non-adiabatic operation. The typical CRN model is comprised of a perfectly-stirred-reactor (PSR), followed by a plug-flow-reactor (PFR), meant to represent the flame, and post-flame zones, respectively. In the two-stage RQL approach two PSR-PFR networks are arranged sequentially, corresponding to the rich and lean stages, with secondary air injection in between. In the authors’ past work, this arrangement has demonstrated the significant sensitivity of exit NOx to the rich stage equivalence ratio, while the amount of secondary air injection was shown to be less critical. In this paper, the CRN model is extended to (1) include the impacts of heat loss and (2) utilize a partially-stirred-reactor (PaSR) approach to study the impacts of mixing on emissions performance. Varying amounts of heat loss are applied to the rich relaxation zone to understand emissions performance and changes to optimization of equivalence ratio and residence time. Premixed and non-premixed configurations are considered in the rich stage PaSR, with varying degrees of mixing intensity to study the interaction between mixing, transport, and kinetic timescales. Critically, the impact of mixing between hot products and secondary air injection is studied to understand practical injector needs. Results show unburnt ammonia leaving the rich stage as a primary contributor to NOx emissions – driven both by increased heat loss and reduced mixing rates. Furthermore, heat losses have shown to create conditions which are conducive to increased N2O formation in the lean stage. The results of this study will be considered in the context of developing optimized two-stage RQL combustors for ammonia..
CrN coating came out as superior and remained completely intact after the irradiation, as evidenced by SEM analysis. Based on these promising results, an in-pile experiment with coated Zircaloy claddings (containing fuel) was performed in the Halden reactor in PWR conditions in 2014. The experimental rig contained four Zircaloy-4-clad fuel rods-three coated (CrN, TiAlN, and AlCrN) and one uncoated. Due to a mechanical deformation of tubes for cooling water within the rig, the fuel rods were insufficiently cooled, resulting in a higher-than-normal cladding temperature. Nevertheless, an SEM examination showed that the CrN coating largely remained intact apart from several local spots where the coating had cracked or disappeared. Underneath the cracked coating, oxide formation was observed in the Zircaloy-4 cladding. The TiAlN and AlCrN coatings both disappeared after the irradiation. (authors)
A large enhancement of the thermoelectric figure of merit is reported in single-crystalline films of CrN. The mechanism of the reduction of the lattice thermal conductivity in cubic CrN is similar to the resonant bonding in IV–VI compounds. Therefore, useful ideas from classic thermoelectrics can be applied to tune functionalities in transition metal nitrides and oxides.
Mg(CrN)2 crystallizes in the tetragonal P-4m2 space group. The structure is two-dimensional and consists of one Mg(CrN)2 sheet oriented in the (0, 0, 1) direction. Mg2+ is bonded to four equivalent N3- atoms to form corner-sharing MgN4 tetrahedra. All Mg–N bond lengths are 2.24 Å. Cr2+ is bonded in a linear geometry to two equivalent N3- atoms. Both Cr–N bond lengths are 1.85 Å. N3- is bonded in a see-saw-like geometry to two equivalent Mg2+ and two equivalent Cr2+ atoms.
Zn(CrN)2 crystallizes in the tetragonal P-4m2 space group. The structure is two-dimensional and consists of one Zn(CrN)2 sheet oriented in the (0, 0, 1) direction. Cr2+ is bonded in a linear geometry to two equivalent N3- atoms. Both Cr–N bond lengths are 1.84 Å. Zn2+ is bonded to four equivalent N3- atoms to form corner-sharing ZnN4 tetrahedra. All Zn–N bond lengths are 2.24 Å. N3- is bonded in a see-saw-like geometry to two equivalent Cr2+ and two equivalent Zn2+ atoms.
Ca(CrN)2 crystallizes in the tetragonal P-4m2 space group. The structure is two-dimensional and consists of one Ca(CrN)2 sheet oriented in the (0, 0, 1) direction. Ca2+ is bonded in a 4-coordinate geometry to four equivalent N3- atoms. All Ca–N bond lengths are 2.31 Å. Cr2+ is bonded in a bent 120 degrees geometry to two equivalent N3- atoms. Both Cr–N bond lengths are 1.81 Å. N3- is bonded to two equivalent Ca2+ and two equivalent Cr2+ atoms to form distorted corner-sharing NCa2Cr2 tetrahedra.
Highlights: • A proper assessment of TEM diffraction pattern along the [001]{sub α-Fe} of a nitrided Fe-Cr alloy is proposed • Diffraction pattern results from the diffraction of the ferritic matrix and the three nitrides variants • Thin foil’s thickness plays a key role in the obtained diffraction pattern • Relrods located in the first layer of the reciprocal lattice can provide extra reflections in the diffraction patterns - Abstract: Upon nitriding of a Fe-3%Cr alloy at 550 °C during 48 h at a nitriding potential K{sub N} = 5 atm{sup −1/2}, finely dispersed CrN grains precipitate. Considering that the nitrides developing within the nitrided layer adopt a cubic, rock-salt structure, Transmission Electron Microscopy (TEM) investigations revealed the Bain orientation relationships (also called Baker-Nutting) existing between the matrix and the precipitates. Given the latter and the structures of both ferrite (bcc) and nitrides (fcc), we have shown that group theory predicts the existence of three nitrides variants, orthogonal to each other, developing in ferrite along the <001>{sub α-Fe} directions, which is in agreement with our experimental observations. The nitrides adopt a very thin platelet-like morphology, energetically corresponding to an absolute extremum. Diffraction patterns obtained along the [001]{sub α-Fe} result from the simultaneous diffraction of the ferritic matrix and the three nitrides variants. The platelet-like nitride precipitates give birth to diffuse intensity lines, originating from the two families developing along the (100) and (010) ferrite planes, as well as possible appearance of additional reflections, located at the forbidden positions {100}{sub α-Fe} and {110}{sub CrN} of the remaining variant, driving the interpretation of such diffraction patterns complicated. Foil thickness has proven to play a key role in the occurrence of this phenomenon. When the geometric diffraction conditions are favorable (i.e. very thin foil along the zone axis and very fine precipitates platelets), TEM analysis permitted to attribute these extra reflections to the nodes located in the first layer of the third variant's reciprocal space.