Search NASA⌕ Search

SEARCH · Search NASA

Results for “CURIE TEMPERATURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Highly Enhanced Curie Temperature in Ga-Implanted Fe3GeTe2 van der Waals Material

Among many efforts in the research of van der Waals (vdW) magnetic materials, increasing the Curie temperature above room temperature has been at the center of research in developing spintronics technology using vdW materials. Here an effective and reliable method of increasing the Curie temperature of ferromagnetic Fe3GeTe2 vdW materials by Ga implantation is reported. It is found that implanting Ga into Fe3GeTe2 by the amount of 10-3 Ga Å-3 could greatly enhance the Fe3GeTe2 Curie temperature by almost 100%. Spatially resolved microdiffraction and element-resolved X-ray absorption spectroscopy show little changes in the Fe3GeTe2 crystal structure and Fe valence state. In addition, the Ga implantation changes the Fe3GeTe2 magnetization from out-of-plane direction at low temperature to in-plane direction at high temperature. The result opens a new opportunity for tailoring the magnetic properties of vdW materials beyond room temperature.

Yang, M↗
DOE OSTI2020

Influence of non-magnetic Cu on enhancing the low temperature magnetic properties and Curie temperature of FeCoNiCrCu(x) high entropy alloys

The microstructure and magnetic properties of three face-centered cubic (FCC) FeCoNiCrCu(x) high entropy alloys (HEAs) (x=0, 0.5, 1) are investigated. Interestingly, addition of the nonmagnetic element Cu to FeCoNiCr HEA is found to enhance exchange interactions and low temperature saturation magnetization. The paramagnetic to ferromagnetic Curie transition temperature increases from 85 K for FeCoNiCr to 118 K for FeCoNiCrCu. This is counterintuitive since Cu is nonmagnetic; however, atom probe tomography revealed Cu rich clusters containing 5 at% Ni and 1 at% each of Fe, Co, Cr, within FCC matrix, these clusters altered the matrix composition and consequently its magnetic properties.

Chaudhary, Varun↗
NASA NTRS1979

Isothermal-desorption-rate measurements in the vicinity of the Curie temperature for H2 chemisorbed on nickel films

Measurements of the isothermal desorption rate of H2 chemisorbed onto polycrystalline nickel films made for temperatures spanning the Curie temperature of the nickel film are presented. Desorption kinetics were followed by measuring the decay of the change in resistance of the nickel film brought about by hydrogen chemisorption after gas-phase H2 had been rapidly evacuated. The desorption rate is found to undergo an anomalous decrease in the vicinity of the Curie temperature, accompanied by an increase in the desorption activation energy and the equilibrium constant for the chemisorbed hydrogen. The results are interpreted in terms of anomalous variations in rate constants for the formation of the precursor molecular adsorbed state and the chemisorbed atomic state due to the phase transition in the nickel. The changes in rate constants are also considered to be in qualitative agreement with theoretical predictions based on a spin coupling between the adatom and the magnetic substrate.

Shanabarger, M. R.↗
DOE OSTI2023

Physics-Informed Machine-Learning Prediction of Curie Temperatures and Its Promise for Guiding the Discovery of Functional Magnetic Materials

High-performance permanent magnets with a high Curie temperature, containing less critical materials, are integral to zero-carbon energy solutions. We built a machine-learning model trained over available experimentally measured Curie temperature values to predict the T C of multicomponent magnetic materials. We chose two compositions from a pseudo-binary (Zr 1–x Ce x )Fe 2 system, namely, (Zr 0.16 Ce 0.84 )Fe 2 and (Zr 0.94 Ce 0.06 )Fe 2 , to experimentally validate the ability of our model to predict the Curie temperature of novel compounds. We also provided a detailed discussion on the correlation of the Curie temperature with the de Gennes scaling factor in rare-earth intermetallic compounds and its breakdown below a certain rare-earth content. The electronic structure calculations (density of states and Fermi surface) were performed using the density functional theory on selected compounds (Zr 0.16 Ce 0.84 )Fe 2 and (Zr 0.94 Ce 0.06 )Fe 2 to understand the electronic origin of a strong magnetic exchange. We found that the change in the electronic density of states and electron/hole fillings at the Fermi level directly correlate with the Curie temperature. Notably, our model was able to capture these key electronic structure trends, which show that physics-informed machine learning can play a crucial role in designing new high-performance magnets with improved properties for environmentally sustainable applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Machine learning predictions of high-Curie-temperature materials

Technologies that function at room temperature often require magnets with a high Curie temperature, $T$ C , and can be improved with better materials. Discovering magnetic materials with a substantial $T$ C is challenging because of the large number of candidates and the cost of fabricating and testing them. Using the two largest known datasets of experimental Curie temperatures, we develop machine-learning models to make rapid $T$ C predictions solely based on the chemical composition of a material. We train a random-forest model and a k -NN one and predict on an initial dataset of over 2500 materials and then validate the model on a new dataset containing over 3000 entries. The accuracy is compared for multiple compounds' representations (“descriptors”) and regression approaches. A random-forest model provides the most accurate predictions and is not improved by dimensionality reduction or by using more complex descriptors based on atomic properties. Further, a random-forest model trained on a combination of both datasets shows that cobalt-rich and iron-rich materials have the highest Curie temperatures for all binary and ternary compounds. An analysis of the model reveals systematic error that causes the model to over-predict low-$T$ C materials and under-predict high-$T$ C materials. For exhaustive searches to find new high-$T$ C materials, analysis of the learning rate suggests either that much more data is needed or that more efficient descriptors are necessary.

36 MATERIALS SCIENCE↗
NASA NTRS1997

A New Probe to Change Curie Temperature of PbTiO3 Sensors

High temperature Raman spectra of nanocrystalline Pb(0.8)Ba(0.2)TiO3, Pb(0.8)Sr(0.2) TiO3, Pb(0.8)La(0.2)TiO3 and Pb(0.8)Ba(0.2)TiO3, have been measured, as a function of particle size. There appears respectively a distinct temperature-induced soft mode phase transition in every sample whose Curie temperature can be determined from the mean-field theory. The detailed Curie temperature shift in modified PbTi03 ceramics by Ba, Sr, La, and Zr, has also been investigated as a function of particle size. This study will favor preparations of high efficiency PbTi03 sensors with an adjustable Curie temperature.

Katiyar, R. S.↗
NASA NTRS1984

High Curie temperature drive layer materials for ion-implanted magnetic bubble devices

Ion implantation of bubble garnets can lower the Curie temperature by 70 C or more, thus limiting high temperature operation of devices with ion-implanted propagation patterns. Therefore, double-layer materials were made with a conventional 2-micron bubble storage layer capped by an ion-implantable drive layer of high Curie temperature, high magnetostriction material. Contiguous disk test patterns were implanted with varying doses of a typical triple implant. Quality of propagation was judged by quasistatic tests on 8-micron period major and minor loops. Variations of magnetization, uniaxial anisotropy, implant dose, and magnetostriction were investigated to ensure optimum flux matching, good charged wall coupling, and wide operating margins. The most successful drive layer compositions were in the systems (SmDyLuCa)3(FeSi)5O12 and (BiGdTmCa)3(FeSi)5O12 and had Curie temperatures 25-44 C higher than the storage layers.

Fratello, V. J.↗
DOE OSTI2023

Tuning the Curie temperature of a two-dimensional magnet/topological insulator heterostructure to above room temperature by epitaxial growth

Heterostructures of two-dimensional (2D) van der Waals (vdW) magnets and topological insulators (TI) are of substantial interest as candidate materials for efficient spin-torque switching, quantum anomalous Hall effect, and chiral spin textures. However, since many of the vdW magnets have Curie temperatures below room temperature, we want to understand how materials can be modified to stabilize their magnetic ordering to higher temperatures. In this work, we utilize molecular beam epitaxy to systematically tune the Curie temperature (T C ) in thin film Fe 3 GeTe 2 /Bi 2 Te 3 from bulklike values (~220 K) to above room temperature by increasing the growth temperature from 300°C to 375°C. For samples grown at 375°C, cross-sectional scanning transmission electron microscopy (STEM) reveals the spontaneous formation of different Fe m Ge n Te 2 compositions (e.g., Fe 5 Ge 2 Te 2 and Fe 7 Ge 6 Te 2 ) as well as intercalation in the vdW gaps, which are possible origins of the enhanced Curie temperature. Furthermore, this observation paves the way for developing various Fe m Ge n Te 2 /TI heterostructures with novel properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High and temperature-insensitive piezoelectric performance in the lead-free Sm-doped BiFeO 3 –BaTiO 3 ceramics with high Curie temperature

Large sensor piezoelectric constant (d 33 = 334 pC/N) and superior actuator piezoelectric constant (d 33 * = 552 pm/V) as well as a high Curie temperature (T C = 454 °C) were obtained simultaneously in the lead-free 0.67Bi 1.03 FeO 3 -0.33Ba 1-x Sm x TiO 3 ceramics. Such an excellent and temperature-insensitive piezoelectric performance with only 10% temperature variation of piezoelectric strain at the range of 25–125 °C is highly desirable for real applications. The structural origin of the enhanced piezoelectric performance is mainly attributed to the morphotropic phase boundary and the highest known tetragonality (c T /a T = 1.02) in such materials. Transmission electron microscopy and electro-mechanical phenomenological theory demonstrate that the superior d 33 and d 33 * are associated with the hybrids nanodomains (60–90 nm) and flattened thermodynamic energy profile owing to the local structure heterogeneity. Furthermore, these results are superior as the piezoelectric properties are temperature-independent and the material has large d 33 *, and high TC compared to other lead-free piezoelectric ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Enhancement of the Curie temperature in single-crystalline ferromagnetic LaCrGe 3 by electron irradiation-induced disorder

LaCrGe 3 has attracted attention as a potential candidate for studies of quantum phase transitions in a ferromagnetic material. The application of pressure avoids a quantum critical point by developing a new magnetic phase. It was suggested that the disorder may provide an alternative route to a quantum critical point. We used low-temperature 2.5 MeV electron irradiation to induce relatively small amounts of pointlike disorder in single crystals of LaCrGe 3 . Irradiation leads to an increase of the resistivity at all temperatures with some deviation from the Matthiessen rule. Hall effect measurements show that electron irradiation does not cause any detectable change in the carrier density. Unexpectedly, the Curie temperature, T FM , increases with the increase of disorder from approximately 90 K in pristine samples up to nearly 100 K in the heavily irradiated sample, with a tendency towards saturation at higher doses. This effect is observed both in resistivity and magnetization measurements. Although the mechanism of this effect is not entirely clear, we conclude that it cannot be caused by effective “doping” or “pressure” due to electron irradiation. Finally, we suggest that disorder-induced broadening of a sharp peak in the density of states, D⁡(E), situated at E p = E F – 0.25 eV below the Fermi energy, E F , causes an increase in D⁡(E F ), leading to an enhancement of T FM in this itinerant ferromagnet.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1991

Mechanically Oriented, Low-Curie-Temperature Materials

Proposed fabrication process produces permanent magnets of greater flux density, intended for use at temperatures far below room temperature. Such magnets parts of electrical motors and other electromechanical actuators operating in cryogenic systems. Performances of actuators increase with flux densities available from their magnets. Based on use of mechanical metallurgical techniques to make oriented magnets of Dy3Al2, because these techniques produce alignments above Curie temperature.

Boltich, Edward B.↗
DOE OSTI2025

Nanoscale Magnetic Ordering Dynamics in a High Curie Temperature Ferromagnet

Thermally driven transitions between ferromagnetic and paramagnetic phases are characterized by critical behavior with divergent susceptibilities, long-range correlations, and spin dynamics that can span kHz to GHz scales as the material approaches the critical temperature T c , but it has proven technically challenging to probe the relevant length and time scales with most conventional measurement techniques. In this study, we employ scanning nitrogen-vacancy center based magnetometry and relaxometry to reveal the critical behavior of a high-T c ferromagnetic oxide near its Curie temperature. Cluster analysis of the measured temperature-dependent nanoscale magnetic textures points to a 3D universality class with a correlation length that diverges near T c . Meanwhile, the temperature-dependent spin dynamics, measured through all optical relaxometry suggest that the phase transition is in the XY universality class. In conclusion, our results capture both static and dynamic aspects of critical behavior, providing insights into universal properties that govern phase transitions in magnetic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Unusual Ferromagnetic Band Evolution and High Curie Temperature in Monolayer 1T‐CrTe2 on Bilayer Graphene

2D van der Waals ferromagnets hold immense promise for spintronic applications due to their controllability and versatility. Despite their significance, the realization and in-depth characterization of ferromagnetic materials in atomically thin single layers, close to the true 2D limit, has been scarce. Here, a successful synthesis of monolayer (ML) 1T-CrTe2 is reported on a bilayer graphene (BLG) substrate via molecular beam epitaxy. Using angle-resolved photoemission spectroscopy and magneto-optical Kerr effect measurements, that the ferromagnetic transition is observed at the Curie temperature (TC) of 150 K in ML 1T-CrTe2 on BLG, accompanied by unconventional temperature-dependent band evolutions. The spectroscopic analysis and first-principle calculations reveal that the ferromagnetism may arise from Goodenough-Kanamori super-exchange and double-exchange interactions, enhanced by the lattice distortion and the electron doping from the BLG substrate. These findings provide pivotal insight into the fundamental understanding of mechanisms governing 2D ferromagnetism and offer a pathway for engineering higher TC in 2D materials for future spintronic devices.

Park, Kyoungree↗
DOE OSTI2023

Synthesis and Characterization of a New Ferroelectric with Low Lead Content, a High Curie Temperature, and a High Piezoelectric Response

Abstract A new solid solution (1− x )Bi(Fe 2/8 Ti 3/8 Mg 3/8 )O 3 –( x )PbTiO 3 (BFTM‐PT) is synthesized and the electromechanical properties are measured. This system is defined as a low‐lead material with ferroelectric/piezoelectric behavior and a morphotropic phase boundary (MPB) that leads to enhanced properties. The MPB is located between x = 0.30 and 0.35 and coincides with a structural phase transition and a sharp increase in the piezoelectric response. The system demonstrates ferroelectric hysteresis where x = 0.325 displays the best properties with a maximum polarization of 39 µC cm −2 and a remnant polarization of 26 µC cm −2 . The range of compositions has high Curie temperature ( T c ), ranging from 625–650 °C. Materials with a T c above 400 °C typically have a low d 33 of <50 pC N −1 at room temperature. However, BFTM‐PT has a higher d 33 that most other compositions with a T c in this range, with the highest being 145 pC N −1 for x = 0.375. The d 33 drops off above 100 °C, but doping studies can be done in the future to stabilize the piezoelectric response at higher temperatures. These outstanding properties open the possibility of new transducer applications, in particular ones requiring high temperature and high power.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Two-dimensional ferromagnetic van der Waals CrCl 3 monolayer with enhanced anisotropy and Curie temperature

Among the recently widely studied van der Waals layered magnets Cr X 3 ( X = Cl, Br, I), CrCl 3 monolayer (ML) is particularly puzzling: it is shown by experiments to have only an in-plane magnetic easy axis and, furthermore, all previous first-principles calculation results contradict this. Through systematic first-principles calculations, we unveil that the in-plane shape anisotropy that dominates over the weak perpendicular magnetocrystalline anisotropy is responsible for the in-plane magnetic easy axis of CrCl 3 ML. Further, to tune the in-plane ferromagnetism of CrCl 3 ML into the desirable perpendicular one, we propose substituting Cr with isovalent tungsten (W). We find that CrWCl 6 has a strong perpendicular magnetic anisotropy and a high Curie temperature up to 76 K. Our work not only gives insight into understanding the two-dimensional ferromagnetism of van der Waals MLs but also sheds new light on engineering their performances for nanodevices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Tunable Magnetic Exchange between Rare-Earth Metal 5d and Iron 3d States: A Case Study of the Multiple Magnetic Transitions in Gd 6 FeBi 2 and the Solid Solutions Dy 6– x Gd x FeBi 2 (1 ≤ x ≤ 5) with Curie Temperatures in the Range 120–350 K

In this paper, the room-temperature magnet Gd 6 FeBi 2 was comprehensively characterized by means of temperature-dependent single-crystal X-ray diffraction, magnetization measurements, and experimental electron density and electronic structure computations. This work explores the electron-spin effects of Fe on this structure and suggests that Gd6FeBi2 shows structural features and exchange interactions, which are clearly distinguishable from other analogues, including the solid solutions Dy 6–x Gd x FeBi 2 (0 ≤ x ≤ 5). The unique traits of Gd 6 FeBi 2 and its derivatives encompass abnormal variations of lattice parameters with the temperature, as well as the presence of multiple magnetic transitions of complex nature. Based on the comprehensive analyses, it can be suggested that the unique magnetic response in this material is the result from tunable Fe spin states, which are coupled with strong Gd 5d–Fe 3d interactions, which differ from other members of this large, structural family. In the ground state, according to density functional theory calculations, the Fe atom carries two net electrons, whose spins are coupled in an antiparallel fashion to the spins of the Gd electrons. Near the Curie temperature, the Fe net moment is reduced intermittently, coupled with a multiple of magnetic transitions. The magnetic correlations are manifested in unexpected variations of the lattice parameters as a function of temperature, suggesting spin–lattice interactions. Furthermore, this study emphasizes the important role of Gd 5d electrons in tuning Fe 3d-based magnetic contribution, which enables better understanding on the spin coupling in other related compounds and sheds light on the development of new magnetic and spintronic compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Macroscopic Monochalcogenide van der Waals Ferroics: Growth, Domain Structures, and Curie Temperature

Two-dimensional and layered van der Waals materials promise to overcome the limitations of conventional ferroelectrics in terms of miniaturization and material integration, but synthesis has produced only small (up to few micrometer-sized) ferroic crystals. Here, we report the realization of in-plane ferroelectric few-layer crystals of the monochalcogenides tin(II) sulfide and selenide (SnS, SnSe) whose linear dimensions exceed the current state of the art by up to 1 order of magnitude. Such large crystals allow the investigation of ferroic domain patterns that are unaffected by edges and finite-size effects. Analysis of the abundant stripe domains by electron microscopy and nanobeam electron diffraction shows two distinct domain types: twin domains separated by positively charged walls with alternating head-to-head and tail-to-tail polarization as well as not previously observed purely rotational domains connected by neutral domain walls with head-to-tail dipoles. Access to large crystals allowed the determination of the Curie temperature of few-layer SnSe van der Waals ferroelectrics, and it enables the investigation of this class of ferroelectrics by widely available methods such as polarized optical microscopy. Furthermore, the combination with layer transfer protocols promises uniform materials for exploring fundamentals and for implementing devices for information processing and energy conversion.

36 MATERIALS SCIENCE↗