Search NASA⌕ Search

SEARCH · Search NASA

Results for “CUT-OUT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

Influence of Cut-outs in Elevator on the Static Longitudinal Stability and on the Static Elevator Effect

The rudder effect of a sport airplane at high angles of attack was to be improved. This made it necessary to make a cut-out in the center of the continuous elevator so as to enlarge the rudder downward. This cut-out which reduced the rudder area by 12.5 percent changed the static stability of the airplane as well as the elevator effect. Flight measurements showed the stability zone with locked elevator to be 1.8 percent less at full throttle and at idling to be 1.3 percent less than the mean wing chord. The effect of the cut-out on the control forces could not be determined owing to insufficient instrumental accuracy at the extremely low existing forces. The measurement of the static controllability resulting from the cut-out manifested an 18 percent drop in elevator effect at full throttle and a 10 to 20 percent drop at idling, depending on lift.

Biechteler, Curt↗
NASA NTRS1947

Stresses Around Rectangular Cut-outs with Reinforced Coaming Stringers

Strain measurements and strength tests were made on six skin-stringer panels under axial load. Three of these panels had short rectangular cut-outs, and three a long one. The width of the cut-out was about one-half of the width of the panel. Three types of coating stringers were used: without reinforcement, with riveted-up reinforcement, or with integral reinforcement. The strain measurements were found to be in good agreement with a previously published theory adapted where necessary by making overlapping assumptions.

Kuhn, Paul↗
NASA NTRS1935

The Aerodynamic Effects of Wing Cut-Outs

In connection with the interference program being conducted in the NACA variable-density wind tunnel, an analysis was made of available material with the object of presenting a qualitative discussion on wing characteristics as affected by cut-outs and of determining means for their quantitative calculation.

Sherman, Albert↗
NASA NTRS1928

Air force and moment for N-20 wing with certain cut-outs

The airplane designer often finds it necessary, in meeting the requirements of visibility, to remove area or to otherwise locally distort the plan or section of an airplane wing. This report, prepared for the Bureau of Aeronautics January 15, 1925, contains the experimental results of tests on six 5 by 30 inch N-20 wing models, cut out or distorted in different ways, which were conducted in the 8 by 8 foot wind tunnel of the Navy Aerodynamical Laboratory in Washington in 1924. The measured and derived results are given without correction for vl/v for wall effect and for standard air density, p=0.00237 slug per cubic foot.

Smith, R H↗
NASA NTRS1931

The Interference Effects on an Airfoil of a Flat Plate at Mid-span Position

This report gives the results of an investigation of the mutual interference of an airfoil and a flat plate inserted at mid-span position. The tests were conducted in the Variable-Density Wind Tunnel of the National Advisory Committee for Aeronautics at a high value of the Reynolds Number. The interference effects of this combination were found to be small. Supplementary tests indicated that the use of fillets decreases both the lift and drag slightly. A bibliography of publication dealing with interference between wings and bodies, and with the effects of cut-outs and fillets is included.

Ward, Kenneth E↗
NASA NTRS1943

The exact solution of shear-lag problems in flat panels and box beams assumed rigid in the transverse direction

A mathematical procedure is herein developed for obtaining exact solutions of shear-lag problems in flat panels and box beams: the method is based on the assumption that the amount of stretching of the sheets in the direction perpendicular to the direction of essential normal stresses is negligible. Explicit solutions, including the treatment of cut-outs, are given for several cases and numerical results are presented in graphic and tabular form. The general theory is presented in a from which further solutions can be readily obtained. The extension of the theory to cover certain cases of non-uniform cross section is indicated. Although the solutions are obtained in terms of infinite series, the present developments differ from those previously given in that, in practical cases, the series usually converge so rapidly that sufficient accuracy is afforded by a small number of terms. Comparisons are made in several cases between the present results and the corresponding solutions obtained by approximate procedures devised by Reissner and by Kuhn and Chiarito.

STRESSED SKIN-PLATES, FLAT↗
NASA NTRS1944

The inward bulge type buckling of monocoque cylinders I : calculation of the effect upon the buckling stress of a compressive force, a nonlinear direct stress distribution, and a shear force

In the present part I of a series of reports on the inward bulge type buckling of monocoque cylinders the buckling load in combined bending and compression is first derived. Next the reduction in the buckling load because of a nonlinear direct stress distribution is determined. In experiments nonlinearity may result from an inadequate stiffness of the end attachments in actual airplanes from the existence of concentrated loads or cut-outs. The effect of a shearing force upon the critical load is investigated through an analysis of the results of tests carried out at GALCIT with 55 reinforced monocoque cylinders. Finally, a simple criterion of general instability is presented in the form of a buckling inequality which should be helpful to the designer of a monocoque in determining the sizes of the rings required for excluding the possibility of inward bulge type buckling.

Hoff, N J↗
NASA NTRS1940

Some data on the static longitudinal stability and control of airplanes : design of control surfaces

In the solution of a number of problems on the stability and controllability of airplanes, there arises the necessity for knowing the characteristics of the tail surfaces of the types in common use today. Of those characteristics, the most important are the effectiveness and hinge moments of the tail surfaces. As has been shown in the present paper, there exists the possibility of determining these characteristics by the formulas obtained with a degree of accuracy sufficient for the purposes of preliminary computation. These formulas take into account a number of fundamental tail characteristics such as tail cut-outs on the control surface and the form of the control surface leading edge.

Martinov, A↗
NASA NTRS1927

Experiments on airfoils with trailing edge cut away

Airfoils with their trailing edge cut away are often found on aircraft, as the fins on the hulls of flying boats and the central section of the wings for affording better visibility. It was therefore of some interest to discover the effect of such cutaways on the lift and drag and on the position of the center of pressure. For this purpose, systematic experiments were performed on two different airfoils, a symmetrical airfoil and an airfoil of medium thickness, with successive shortenings of their chords.

AIRFOILS↗