Green and durable engineered cementitious composites (GD-ECC) with recycled PE fiber, desert sand, and carbonation curing: Mixture design, durability performance, and life-cycle analysis
Not provided.
Construction & Building Technology↗
SEARCH · Search NASA
Results for “Carbonation curing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The Impact of Carbonation Curing on the Fatigue Behavior of Polyvinyl Alcohol Engineered Cementitious Composites (PVA-ECC)
Use of Engineered Cementitious Composites (ECC) has been proven to enhance structural fatigue resistance and reduce the use-phase emissions for transportation infrastructure. Carbonation curing offers an opportunity to reduce the embodied carbon of ECC via direct CO 2 sequestration. In this study, the impact of carbonation curing on ECC’s fatigue resistance was examined. ECC’s CO 2 uptake, static flexural behavior, flexural fatigue performance, and single fiber pull-out behavior were studied experimentally. Midspan deflection up to 3 million cycles under fatigue load, fatigue stress-life relationship, and failure mechanism for carbonation-cured and air-cured ECC were investigated. Carbonation curing was found to significantly improved the fatigue life of ECC and lowered the midspan deflection under the same stress. Further, CO 2 -cured ECC can achieve >20% CO 2 uptake per cement mass after 24-hour carbonation curing. Carbonation curing increased ECC’s flexural strength by 32% and promoted crack width control capability, with maximum post-fatigue crack width reduced from 148 μm to 76 μm. As a result, the positive impact of carbonation curing on the fatigue behavior of ECC simultaneously lowers the embodied and operational carbon of ECC structural members subjected to fatigue loading during service.
36 MATERIALS SCIENCE↗
Development of sustainable low carbon Engineered Cementitious Composites with waste polyethylene fiber, sisal fiber and carbonation curing
Engineered cementitious composites (ECC) is an advanced fiber-reinforced cementitious composite with high tensile ductility. However, the binder and fiber system in ECC incur high economic and environmental cost. In this study, a low carbon ECC was developed by substituting virgin polyethylene fiber with waste polyethylene fiber (WPE) from waste marine fishing nets. Carbonation curing was applied to further reduce embodied carbon footprint via direct CO 2 mineralization. This research examined the low carbon ECC’s mechanical properties, including compressive strength and tensile strength and ductility. The CO 2 footprint and material costs of ECC were also investigated. The objective was to develop an ECC competitive to normal concrete economically and environmentally while maintain the unique ductile performance of ECC. Results suggest that carbonation-cured WPE reinforced ECC possesses 50% of the CO 2 footprint and 37% of the cost of traditional concrete. Meanwhile, this low carbon ECC maintains at least 4 MPa tensile strength and 6% tensile ductility. This research demonstrates the feasibility of developing construction materials with low environmental impact while maintaining high performance for civil infrastructure applications. As a result, the adoption of WPE in ECC provides a plausible pathway to recycle marine waste into the construction industry that urgently needs to be decarbonized.
42 ENGINEERING↗
Life cycle assessment of railway ties fabricated with ductile cementitious composites and carbonation curing
This paper evaluates the lifecycle economic and environmental benefits of implementing CO 2 utilization and storage within advanced engineered cementitious composite (ECC) railway ties. Using CO 2 -treated ECC ties can yield lifecycle benefits primarily due to enhanced material properties – increased lifespan in this case – instead of due to the stored CO 2 that would otherwise enter the atmosphere. Sequestration-based policies such as 45Q in the United States would therefore not incentivize deployment of ECC railway ties, despite their considerable CO 2 avoidance opportunities. To reach these conclusions, cradle-to-grave lifecycle models were developed for ECC ties and conventional concrete ties and evaluated under 1000 possible use-phase scenarios. The models incorporated premature tie failures – consistent with real-world observations – that were used to study a wide range of non-linear impacts arising from the random nature of tie failures and replacements. The results show that past studies that neglected premature failure of ties may have underestimated lifecycle greenhouse gas (GHG) emissions of concrete rail ties by nearly three times. Overall, servicing a track with ECC ties instead of concrete ties can reduce the lifecycle costs and GHG emissions by 12% and 21% respectively, based on median values of 1000 model run results. The expected benefits would be larger for entities like Amtrak that plan to expand concrete tie infrastructure despite significant challenges with premature concrete tie failures. Furthermore, the results of this study suggest that the lifespan of ECC ties needs to be at least 25% longer than concrete ties to achieve net lifecycle benefits. The possibility of this should be tested and confirmed under real-world conditions.
42 ENGINEERING↗
Amino acids as performance-controlling additives in carbonation-activated cementitious materials
This article presents an investigation on the application of amino acids to control the CaCO{sub 3} crystallization in carbonation cured wollastonite composites. It was observed that wollastonite carbonated without any amino acid formed calcite as the primary polymorph of CaCO{sub 3}. In contrast, the use of amino acids as admixtures resulted in the formation of stable amorphous calcium carbonate (ACC), vaterite, and aragonite during the carbonation of wollastonite. The carbonated composites produced with amino acids were observed to have a lower critical pore size, but a higher total porosity, compared to the control batch. Additionally, the utilization of amino acids was observed to increase the flexural strength and compressive strength of the composites up to 106% and 48%, respectively, compared to the control batch. Such performance enhancement of the carbonated composites in the presence of amino acids was attributed to the reduced critical pore size and the formation of organic-inorganic hybrid phases in the matrix.
36 MATERIALS SCIENCE↗
Carbon fiber/epoxy vitrimer composite patch cured with bio‐based curing agents for one‐step repair metallic sheet and its recyclability
Abstract Vitrimers have gained a great deal of attention from researchers, yet research on its application is still lacking. This study, a novel bio‐based vitrimer was developed from epoxy (EP) and bio‐based curing agents, that is, cashew nut shell liquid (CNSL) and citric acid (CA), and then reinforced by carbon fiber. The vitrimers with different ratios of acid to epoxy (R ratio) at 0.30–0.40 contained ester and ether linkages. All EP/CA/CNSL vitrimers showed the stress relaxation over 70–100°C due to transesterification. The vitrimers were applied as polymer matrices for the carbon fiber composites and then used as repair patches. By using the carbon fiber‐reinforced vitrimer with the R ratio of 0.30, patch repair on a damaged alloy sheet revealed that approximately 98% of the tensile strength of the damaged alloy sheet was recovered. The vitrimer can be dissolved from carbon fiber composite to recover carbon fiber. The recovered carbon fiber retained good tensile strength compared to the pristine composite. Based on this study, the EP/CA/CNSL vitrimers showed the comparable thermomechanical properties with the epoxy vitrimer cured by the petroleum‐based curing agent. The vitrimer composite patch could therefore be an alternative new repair method to extend the service life of damaged structures.
Lorwanishpaisarn, Narubeth↗
Tandem CO 2 valorisation to polycarbonate vitrimer and ethylene carbonate
The need for renewably sourced polymers has intensified with the worsening of global challenges such as emissions and plastic pollution. Here, we report a CO 2 -based poly(cyclohexene carbonate) (PCHC) vitrimer cured with zinc stearate that directly addresses both issues. Enhanced zinc dispersion within the network enabled faster curing and reprocessing than possible with zinc acetate systems, while maintaining consistent T g and mechanical integrity across multiple cycles. The vitrimer undergoes rapid glycolysis in ethylene glycol, valorisation into ethylene carbonate with up to 97% yield without additional catalyst. When applied to carbon fibre-reinforced polymers (CFRPs), applying this strategy enabled the development of sustainable CO 2 -based CFRP that can undergo full resin valorisation and recovery of clean, damage-free fibres. Collectively, this tandem CO 2 valorisation strategy—from vitrimer synthesis to fibre-reinforced composites and subsequent chemical valorisation—establishes multiple recycling and valorisation pathways and provides a promising routte for carbon capture and utilization as well as material recycling.
36 MATERIALS SCIENCE↗
Effects of cleavable comonomer structure and crosslinker chemistry on the performance and deconstructability of frontally cured pDCPD composites
Reclaiming undamaged carbon fiber from thermoset composites requires chemical recycling methods that leverage complete deconstruction of the polymer matrix. Cleavable comonomers enable chemical recycling of poly(dicyclopentadiene) (pDCPD) composites, but current systems suffer from reduced glass transition temperature (T g ), limiting application. Here, we investigate the effect of cleavable comonomer loading and cleavable crosslinker chemistry on network formation, thermomechanical properties, and fiber recovery in frontally cured pDCPD composites. All formulations fully deconstructed in acid and recovered fibers ranged from pristine to variably contaminated depending on crosslinker chemistry. Reducing backbone-cleaving comonomer content and introducing cleavable crosslinkers raised composite T g to 126–138 °C compared to 105 °C previously reported in deconstructable pDCPD composites. Although the cleavable crosslinkers increased T g in unreinforced polymers to 150–160 °C, the fiber-reinforced composite T g remained lower due to under-curing and interactions between the crosslinkers and the fiber surface. Increasing polymerization initiator loading improved comonomer conversion and yielded a deconstructable composite with T g = 151 °C, approaching the performance of non-deconstructable pDCPD composites (T g = 161 °C). This work clarifies how cleavable comonomer and crosslinker chemistry governs curing, thermomechanical performance, and reclaimed reinforcement quality, and the results highlight the need for more robust cleavable comonomers to realize multigenerational composite materials without sacrificing thermomechanical performance.
Carbon fibers↗
Chemically and Mechanically Recyclable Vitrimers from Carbon Dioxide-Based Polycarbonates
Designing thermoset materials with dynamic crosslinks is an important strategy to mitigate rising global carbon dioxide emission levels. The development of polymers from sustainable feedstocks, with efficient manufacturing methods, for high-value applications, and with circular end-of-use solutions is essential for advancing material technologies. One approach involves exploiting carbon dioxide itself as feedstock to create high performance, sustainable materials, by enchaining 50 mol% CO2 via copolymerization with epoxides to yield polycarbonates. This work describes the synthesis, end-functionalization, and curing of poly(propylene carbonate) (PPC) and poly(cyclohexene carbonate) (PCHC) into beta-hydroxy ester vitrimers. These vitrimers demonstrate the ability to be mechanically reprocessed up to 3 times with retention of the material’s properties through dynamic transesterification exchange reactions. The polycarbonate vitrimers with gel fractions exceeding 90 % exhibit high tensile strength (> 50 MPa) and Young’s modulus (> 2 GPa), achieved by varying repeat unit structure in the polymer backbone from the low Tg PPC to the more rigid high Tg PCHC structures. Owing to an entropically favorable chain back-biting mechanism, the network chains can be cleaved and depolymerized into cyclic small molecules. In the case of PCHC, this process enables repolymerization back to polycarbonates with 69 wt.% CO2 retention through life-cycles. The promising mechanical performance and recyclability of these CO2-based polycarbonate vitrimers indicate their potential for sustainable, high-performance materials, paving the way for future innovations in circular polymer technologies and carbon capture utilization.
36 MATERIALS SCIENCE↗
A parametric study of accelerated carbonation in alkali-activated slag
Resistance to carbonation is one important attribute that low-CO{sub 2} cement alternatives must possess, and is particularly crucial for cement alternatives subjected to aggressive CO{sub 2} concentrations such as those used in construction of oil wells and wells for below ground carbon sequestration. Here, a parametric study of alkali-activated slag (AAS) carbonation in aggressive environments has been conducted to examine (i) calcium carbonate polymorphism using X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy, and (ii) the extent of calcium carbonate formation and CO{sub 2} adsorption using thermogravimetric analysis (TGA). A range of AASs have been studied by varying the magnesium content of the slag, the activator type (sodium hydroxide and sodium silicate), the activator concentration, and the curing time prior to carbonation. It was uncovered that both (i) magnesium from the slag and (ii) silica from the activating solution are needed to reduce the propensity for the sodium-containing calcium-alumino-silicate-hydrate gel to undergo decalcification.
36 MATERIALS SCIENCE↗
Additive manufacturing of carbon fiber-reinforced thermoset composites via in-situ thermal curing
Fiber-reinforced polymer composites are lightweight structural materials widely used in the transportation and energy industries. Current approaches for the manufacture of composites require expensive tooling and long, energy-intensive processing, resulting in a high cost of manufacturing, limited design complexity, and low fabrication rates. Here, we report rapid, scalable, and energy-efficient additive manufacturing of fiber-reinforced thermoset composites, while eliminating the need for tooling or molds. Use of a thermoresponsive thermoset resin as the matrix of composites and localized, remote heating of carbon fiber reinforcements via photothermal conversion enables rapid, in-situ curing of composites without further post-processing. Rapid curing and phase transformation of the matrix thermoset, from a liquid or viscous resin to a rigid polymer, immediately upon deposition by a robotic platform, allows for the high-fidelity, freeform manufacturing of discontinuous and continuous fiber-reinforced composites without using sacrificial support materials. This method is applicable to a variety of industries and will enable rapid and scalable manufacture of composite parts and tooling as well as on-demand repair of composite structures.
36 MATERIALS SCIENCE↗
Prediction of curing kinetics of resorcinol‐added resole phenolic resins using differential scanning calorimetry for the fabrication of carbon/carbon composites
Phenolic resins are commonly used as carbon precursors for the fabrication of carbon/carbon composites due to their high carbon yield and aromatic nature. To decrease curing times, acid catalysts are generally used, but the addition of resorcinol was found to have a similar effect while being incorporated into the resin matrix with no contamination or corrosion issues. In this work, the curing kinetics of pure, 10, 20, and 30 wt% resorcinol-added phenolic resins were investigated through differential scanning calorimetry. Heating rates of 0.5, 1, 2.5, and 5°C min -1 were used with several curing models to predict isothermal curing. Averaged mean absolute error (MAE) for the isoconversional mathematical approaches namely Kissinger–Akahira–Sunose (MAE = 12.9 min), Flynn–Wall–Ozawa (15.8 min), and Vyazovkin (14 min) show that these methods provide the best predictions, attributed to their adoption of an activation energy that depends on the extent of cure (E a (α)). The Kissinger method (MAE = 36 min), which depends only on peak temperature with a constant activation energy assumption, and the data noise sensitive Friedman model (MAE = 1144.7 min) provide the least accurate results. Thermogravimetric analysis revealed that resorcinol decreases the curing times by up to 71% without lowering carbon yield.
36 MATERIALS SCIENCE↗
Storing Co 2 in Built Infrastructure: Co 2 Carbonation of Precast Concrete Products
The overall objective of the proposed study was to advance the technical understanding of CO 2 incorporation into novel cementitious materials for the development of high value products that provide a net reduction in carbon emissions. This project combined two primary phases of research that addressed technical barriers related to (i) optimizing CO 2 storage capability of cementitious materials, (ii) evaluating and enhancing physical properties of novel carbonated materials, and (iii) assessing the reductions in life cycle CO 2 emissions attributed to CO 2 carbonation of precast cementitious materials. Engineered cementitious composites (ECC) are a class of highly ductile concrete composites that have been shown to be very durable when used in the built environment. CO 2 carbonation of ECC was examined in this study and it was found that precast ECC specimens could sequester up to 35% CO 2 by cement mass after 24 hours of curing at a CO 2 pressure of 0.5 MPa and 23°C and had a strain capacity of 3%. Carbonation conditions were optimized at the bench-scale and then utilized to create full-scale CO 2 -cured ECC railroad ties that were field tested on a train track. Rail ties were selected for this initial assessment of CO 2 storage in precast concrete materials due to the large market for concrete ties in the railroad industry. Although the full-scale rail ties passed all of the required American Railway Engineering and Maintenance-of-Way Association qualifying mechanical tests, on-track testing of the CO 2 -cured ECC rail ties was unsuccessful due to fiber alignment in the ECC the during the rail tie casting process which prevented the material from achieving the expected level of strain capacity. This result highlights the challenge in scaling up bench-scale processes to full-scale product manufacturing and requires additional investigation into the casting process of large-scale infrastructure elements using ECC combined with carbonation curing. Life cycle assessment of a CO 2 -cured ECC rail tie versus a traditional concrete rail tie indicates that the ECC tie can have lifecycle carbon savings of between 11% and 51% depending on how much longer its useful lifetime is compared to traditional concrete rail ties. Both carbon and cost savings are driven by a reduction in the need to replace broken rail ties, so the key factor is the extent to which a CO 2 -cured ECC rail tie will have increased lifetime durability compared to alternative rail ties.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Microbial Curing of Cement for Energy Applications
Rutgers University, Lawrence Livermore National Laboratory, and the University of Arizona executed this program over 36 months with a 4-Task Program: (M1)-Microbial Engineering (M2)-Microstructure Modelling, (M3) Cement and Concrete Formulation, (M4)-Techno-economic analysis (TEA) and lifecycle assessment (LCA). This program developed a new carbonate cement concrete manufacturing process called microbial curing (MBC). MBC utilizes in-situ microbial production of CO 2 that dissolves into pore-bound water to carbonate a cementitious material creating a bonding matrix of CaCO 3 and SiO 2 that hardens and densifies the material. This is the first work of this type where calcium silicate was used in microbial studies. All other work reported in the literature always used a soluble form of calcium. This final report describes the work done in the final quarter, the best procedures and results, and the final techno-economic and lifecycle analyses. This quarter, we cast and cured twenty-five (4”x8”) cylinder samples. The compressive strength, split tensile, Young’s modulus, chloride permeability, and creep measurements were performed. These measurements demonstrated that MBC of calcium silicate concrete exhibits scaling problems due to the escape of ammonia gas, a product of the microbial reaction to generate CO 2 . As curing proceeds, the ability for the gas to escape from within the cylinder is restricted by the outer cylindrical portions densifying, making the outer portion highly impermeable to gas flow. In contrast, the small samples cured are uniformly cured, forming materials whose mechanical properties are 7x better than the large samples. This problem needs to be solved before this technology can be commercialized. The techno-economic and lifecycle analyses indicate that the technology developed in this program exhibits a significant opportunity to reduce the cost of cement and CO 2 emissions associated with concrete, provided the curing issue associated with larger samples can be addressed.
36 MATERIALS SCIENCE↗
Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes
We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.
25 ENERGY STORAGE↗
Impact of DMP-30 catalyst concentration on the degradation and kinetics of bisphenol A epoxy thermosets cured with linear amine hardener
Epoxy thermosets are a crucial component in carbon-fiber composites, serving as the organic binding matrix. Catalysts are commonly used in prepolymer formulations to accelerate curing of the thermosets. However, the impact of catalysts on the thermal stability, degradation pathways, and kinetics of the final thermoset is poorly understood. Here, in this work, Product-Specific Kinetics (PSK) analysis was utilized with isoconversional kinetics to provide a first look into the degradation kinetics of major pyrolysis pathways in bisphenol A (BPA) epoxy resins and determine the impact of altering catalysis concentrations on these kinetic pathways. Results revealed new insights into previously identified degradation pathways, provided evidence of multiple degradation pathways for some products, and showed that use of excess catalyst results in polymer network alterations and reduced thermal stability of the thermosets.
Bisphenol A↗