SEARCH · Search NASA
Results for “Cathode limitations”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Controlling hazardous reactions during voltage reversal of high energy lithium cells
The roll of general cell design characteristics in preventing hazardous reactions during voltage reversal of lithium cells is discussed. Anode limited versus cathode limited design and case positive versus case negative design are addressed.
Noise as a tool for evaluating the activation of cathodes
Measurements, at low frequencies, of the shot noise current from space charge limited cathodes always produced results substantially in excess of theoretical predictions. Measuring the ratio (I sub eq)/S yielded a relation (I sub eq)/S = 1.288 V sub k = 1.288 k(T sub k)/e, independent of the operating point of the diode (triode) as long as all parts of the cathode had a full space charge controlled emission. This method was so sensitive as to permit detection of cathode temperature changes by 1 K, thus it allowed a powerful screening method between well and poorly activated cathodes, superior to dip tests and other current-voltage methods.
Aqueous solution-based synthesis approach for carbon-disordered rocksalt composite cathode development and its limitations
Disordered rocksalt cathodes exhibit high specific capacities and high energy density; however, their low electronic conductivity poses a great challenge. Herein, we explored an aqueous-solution-based synthesis route that involves controlling the surface charges of Li 1.2 Mn 0.6 Ti 0.2 O 1.8 F 0.2 (LMTOF) to be anchored by a few-layer reduced graphene oxide (rGO) for the first time. The uniform rGO wrapping on the surface of the LMTOF particles is achieved by electrostatic attraction between the negatively charged rGO and positively charged LMTOF particles. Although the initial specific capacity of rGO-LMTOF composite increased by 58 % compared to the pristine LMTOF, the composite experienced a severe capacity fade over cycling. The synthesis process in an aqueous medium resulted in Li + /H + exchange and TM dissolution as evidenced from inductively coupled plasmon analysis and X-ray diffraction analysis. Therefore, this work suggests the search for alternative media or conditions for the synthesis of carbon-disordered rock salt cathode composite.
Study of Cathode Gas Diffusion Architecture for Improved Oxygen Transport in Hydroxide Exchange Membrane Fuel Cells
The high pH environment in hydroxide exchange membrane fuel cells (HEMFCs) has the potential to reach lower costs than the current proton exchange membrane fuel cells (PEMFCs), the incumbent technology. A significant difference between HEMFCs and PEMFCs is the location of water production within the cell. In PEMFCs, the water is produced on the cathode, limiting oxygen transport. In HEMFCs, the water is produced on the anode where the fuel is pure hydrogen. This allows the cathode to be optimized for oxygen transport without the presence of excess liquid water. Limiting current analysis, a technique previously used in PEMFCs, is adopted in HEMFCs to evaluate the oxygen mass transport resistances for different sections of the cathode. Through elimination of the microporous layer (MPL), gas diffusion layer (GDL), and traditional flow field and using porous nickel foam for gas distribution, the transport resistance at an operating condition of 150 kPa(g) and with the cell temperature at 80 °C was decreased from 112 s m −1 to 48 s m −1 , effectively halved. The optimal configuration for performance was found with Ni foam and a GDL, eliminating the MPL and traditional flow field, which vastly improved oxygen transport while maintaining adequate electrical contact with the cathode catalyst layer.
Electrochemical impedance spectroscopy of lithium-titanium disulfide rechargeable cells
The two-terminal alternating current impedance of Li/TiS2 rechargeable cells was studied as a function of frequency, state-of-charge, and extended cycling. Analysis based on a plausible equivalent circuit model for the Li/TiS2 cell leads to evaluation of kinetic parameters for the various physicochemical processes occurring at the electrode/electrolyte interfaces. To investigate the causes of cell degradation during extended cycling, the parameters evaluated for cells cycled 5 times were compared with the parameters of cells cycled over 600 times. The findings are that the combined ohmic resistance of the electrolyte and electrodes suffers a tenfold increase after extended cycling, while the charge-transfer resistance and diffusional impedance at the TiS2/electrolyte interface are not significantIy affected. The results reflect the morphological change and increase in area of the anode due to cycling. The study also shows that overdischarge of a cathode-limited cell causes a decrease in the diffusion coefficient of the lithium ion in the cathode.
Modeling and validation of single-chamber microbial fuel cell cathode biofilm growth and response to oxidant gas composition
This work describes experiments and computational simulations to analyze single-chamber, air-cathode microbial fuel cell (MFC) performance and cathodic limitations in terms of current generation, power output, mass transport, biomass competition, and biofilm growth. Steady-state and transient cathode models were developed and experimentally validated. Two cathode gas mixtures were used to explore oxygen transport in the cathode: the MFCs exposed to a helium-oxygen mixture (heliox) produced higher current and power output than the group of MFCs exposed to air or a nitrogen-oxygen mixture (nitrox), indicating a dependence on gas-phase transport in the cathode. Multi-substance transport, biological reactions, and electrochemical reactions in a multi-layer and multi-biomass cathode biofilm were also simulated in a transient model. The transient model described biofilm growth over 15 days while providing insight into mass transport and cathodic dissolved species concentration profiles during biofilm growth. Lastly, simulation results predict that the dissolved oxygen content and diffusion in the cathode are key parameters affecting the power output of the air-cathode MFC system, with greater oxygen content in the cathode resulting in increased power output and fully-matured biomass.
Mercury vapor hollow cathode component studies
An experimental study of starting and operating characteristics of conventional hollow cathodes and of hollow cathodes without alkaline earth emissive materials demonstrated that the emissive mix is essential to obtain the desired cathode operation. Loss of the emissive mix by evaporation and chemical reaction was measured. New insert designs consisting of emissive mix supported on nickel and of barium impregnated porous tungsten were studied. Cathodes with a modified orifice geometry operated in a low voltage, 'spot' mode over a broad range of discharge current. Thermal degradation tests on cathode heaters showed the flame sprayed SERT II type to be the most durable at high temperatures. Thermal shock was observed to be a significant factor in limiting cathode heater life. A cathode having a barium impregnated porous tungsten tip and a heater which is potted in sintered alumina was found to have favorable operating characteristics.
All-Sputtered, Superior Power Density Thin-Film Solid Oxide Fuel Cells with a Novel Nanofibrous Ceramic Cathode
Thin film solid oxide fuel cells (TF-SOFCs) are attracting attention due to their ability to operate at comparatively lower temperatures (400–650 °C) that are unattainable for conventional anode-supported SOFCs (650–800 °C). However, limited cathode performance and cell scalability remain persistent issues. Here, we report a new approach of fabricating yttria-stabilized zirconia (YSZ)-based TF-SOFCs via a scalable magnetron sputtering process. Notable is the development and deposition of a porous La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 2.95 (LSCF)-based cathode with a unique fibrous nanostructure. This all-sputtered cell shows an open-circuit voltage of ~1.0 V and peak power densities of ~1.7 and ~2.5 W/cm 2 at 600 and 650 °C, respectively, under hydrogen fuel and air along with showing stable performance in short-term testing. The power densities obtained in this work are the highest among YSZ-based SOFCs at these low temperatures, which demonstrate the feasibility of fabricating exceptionally high-performance TF-SOFC cells with distinctive dense or porous nanostructures for each layer, as desired, by a sputtering process. This work illustrates a new, potentially low-cost, and scalable platform for the fabrication of next-generation TF-SOFCs with excellent power output and stability.
The cycle life chemistry of ambient-temperature secondary lithium cells
The Jet Propulsion Laboratory is involved in a NASA-sponsored research program to demonstrate the feasibility of ambient-temperature secondary lithium batteries for geosynchronous space applications. Encouraging cycle life has been demonstrated in sealed, cathode-limited laboratory cells. However, the cell capacity declines with cycle life. The results of recent studies of the lithium electrode passivation chemistry, and of conductive diluents for TiS2 cathodes and their possible contribution to capacity decline, are here presented. Technical issues associated with the unique operational requirements of a geosynchronous mission are also described.
A Study on the Corrosion Behavior of Carbon Steel Exposed to a H{sub 2}S-Containing NH{sub 4}Cl Medium
NH{sub 4}Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H{sub 2}S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H{sub 2}S concentration, on the corrosion behavior of carbon steel in an NH{sub 4}Cl environment with the presence of H{sub 2}S. The effect of H{sub 2}S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H{sub 2}S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H{sub 2}S environment, and the corrosion product film was tight and protective. The ammonia from NH{sub 4}Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness (R{sub a}) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH{sub 4}Cl environment with the presence of H{sub 2}S.
Influence of solvents on electrochemical stability window of ionic liquid solutions
The electrochemical stability window (ESW) defines the voltage range within which an electrolyte remains stable against oxidation and reduction, serving as a key descriptor for ionic liquid (IL)-based systems. The ESWs of 15 ILs with diverse cation-anion combinations were systematically investigated, both in their neat forms and as binary mixtures with three representative solvents, i.e., propylene carbonate (PC), ethylene glycol (EG), and tetrahydrofuran (THF). Cyclic voltammetry on a glassy carbon electrode determined anodic and cathodic stability limits, revealing that ESW protection in IL-solvent mixtures strongly depends on solvent polarity, proticity, and IL compatibility. PC, with a high dielectric constant and aprotic character, broadened anodic limits and moderately stabilized cathodic limits. THF maintained compact interfacial structure, offering additional cathodic protection, whereas EG, being protic, reduced ESWs via proton-coupled electron transfer and hydrogen evolution. The solvent protection trend followed by PC > THF > EG, with bulky, hydrophobic cations ([HMIM] + , [BMPYRR] + ) and weakly coordinating anions ([NTF 2 ] - , [DCA] - , [DEP] - ) showing the highest ESW protection for 50 mol% IL in these solvents. Among the neat ILs, [EMIM][DEP], [HMIM][PF 6 ], and [BMPYRR][DCA] showed wide ESWs of ∼5.5 V. These results provide valuable insight into solvent-modulated electrochemical stability, enabling rational design of IL-based electrolytes for energy storage and electrosynthesis.
Disordered Rocksalts as High‐Energy and Earth‐Abundant Li‐Ion Cathodes
To address the growing demand for energy and support the shift toward transportation electrification and intermittent renewable energy, there is an urgent need for low‐cost, energy‐dense electrical storage. Research on Li‐ion electrode materials has predominantly focused on ordered materials with well‐defined lithium diffusion channels, limiting cathode design to resource‐constrained Ni‐ and Co‐based oxides and lower‐energy polyanion compounds. Recently, disordered rocksalts with lithium excess (DRX) have demonstrated high capacity and energy density when lithium excess and/or local ordering allow statistical percolation of lithium sites through the structure. This cation disorder can be induced by high temperature synthesis or mechanochemical synthesis methods for a broad range of compositions. DRX oxides and oxyfluorides containing Earth‐abundant transition metals have been prepared using various synthesis routes, including solid‐state, molten‐salt, and sol‐gel reactions. This review outlines DRX design principles and explains the effect of synthesis conditions on cation disorder and short‐range cation ordering (SRO), which determines the cycling stability and rate capability. In addition, strategies to enhance Li transport and capacity retention with Mn‐rich DRX possessing partial spinel‐like ordering are discussed. Finally, the review considers the optimization of carbon and electrolyte in DRX materials and addresses key challenges and opportunities for commercializing DRX cathodes.
Solvent‐Phobic and Ionophilic Carboxylated Polythiophene Layer for Fluoride‐Rich Cathode Electrolyte Interphase
Abstract One focal area of contemporary organic mixed ionic‐electronic conductor (OMIEC) research relates to utilization of dual‐conductive properties to enhance the ion/electron transfer kinetics for energy storage applications. Insight regarding OMIEC response toward the electrolyte anion and solvent used in lithium‐ion batteries (LIBs), however, is limited. Here, for the first time, the solvent‐phobic and ionophilic (SP‐IP) properties of the OMIEC, poly[3‐(potassium‐4‐butanoate)thiophene‐2,5‐diyl] (P3KBT), are revealed through comprehensive evaluation and characterization. The solvent‐phobic characteristics arise from the cooperation of dispersive interaction, polar interaction, and hydrogen‐bonding between P3KBT and electrolyte solvent. The ionophilic nature is driven by electrostatic interactions between P3KBT side chain carboxylate groups and LiPF 6 , and the reversible electrochemical doping/de‐doping of the polythiophene backbone with PF 6 ⁻ . The SP‐IP properties induce formation of a LiF‐ rich , Li 2 CO 3 ‐ limited cathode electrolyte interphase (CEI) layer when a P3KBT coating layer is applied to the active material surface, significantly improving half‐cell life to over 1500 cycles at 2C.
Delineating the Factors Impacting the Electrochemical Behavior of Single-Crystal High-Nickel Layered Oxide Cathodes
High-nickel (Ni) (≥80%) single-crystal LiNi 1-x-y Mn x Co y O 2 (NMCs) have garnered recent interest as cathodes in lithium (Li)-ion batteries (LIBs). However, capacity fade at high voltages, particularly after the onset of the H2–H3 phase transition, hampers their viability. In this study, single-crystal LiNi 0.8 Mn x Co 0.2-x O 2 (x = 0.2, 0.1, 0) are synthesized and tested in LiPF 6 in ethyl methyl carbonate-based electrolytes, with and without monofluoroethylene carbonate and LiF 2 PO 2 additives, to clarify the effects of Co/Mn ratio and surface stabilization on high-voltage cycling degradation. By imposing a kinetic barrier to the accessible H2–H3 capacity, surface reconstruction is identified as the primary driver of high-voltage capacity loss, being greater in the Co-free cathode and in the absence of fluorinated electrolyte components. This is attributed to a synergy between increased mechanical stress due to worsened bulk and interfacial H2–H3 kinetics and decreased interfacial stability due to the poor passivating capability of the electrolyte. Here, the findings highlight the importance of limiting cathode impedance growth during high-voltage cycling, which can be achieved by tuning bulk dopants and electrolyte chemistry.
Toward Realizing the Potential of Practical Li-O2 Batteries for Electric Aircraft
Electrochemical power sources based on the Li-O2 couple have potential to achieve more than two-times the specific energy that is achievable with state-of-the-art Li-ion technologies. Despite considerable research, significant practical limitations continue to impede the successful realization of the Li-O2 electrochemistry as a power source in electric and hybrid-electric aviation. In practice, power capability and cycle life present formidable challenges. In this work, projections are presented for Li-O2prismatic cells with lightweight construction and the effect of cathode-limited capacity and discharge rate on specific energy and power are presented.
High Energy Aqueous Lithium-Ion Batteries (Final Report)
Lithium-ion batteries (LIBs) are a widely used energy storage device. For decades, researchers have been studying aqueous electrolytes due to their non-flammability and environmental friendless. However, the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) of water greatly limit the voltage window of the aqueous electrolyte. The recent concept of ‘solvent-in-salt’ electrolytes, namely ‘water-in-salt’ electrolytes (WISE) for aqueous batteries and ‘super-concentrated’ electrolytes for non-aqueous batteries, greatly expands the electrochemical window of these battery systems and consequently their energy density. This expansion occurs because the large number of salt aggregates in ‘solvent-in-salt’ electrolytes enables preferential salt decomposition over solvent decomposition to form robust interphase layers on electrodes, thus enhancing their stability in a wide range of operating voltages. However, even when the salt concentration reached 63m, regardless of cost, the cathodic potential of the WISE expanded only to 1.75V with an overall electrochemical stability window of <3.25V. To design the next generation of high energy aqueous LIBs, electrolytes that possess a wider electrochemical stability window and lower cost but still maintain the merit of non-flammability are much needed. In this project, we designed the aqueous LIBs with widened voltage window. We reported a cheap and non-flammable ternary eutectic electrolyte that can form a robust solid electrolyte interface (SEI)so that the cathodic limiting potential can be decreased to <1.5 V for Li 4 Ti 5 O 12 anodes, while maintaining both a high ionic conductivity of >10 -3 S cm –1 and a low viscosity. We demonstrated the super-stable2.5V LiMn 2 O 4 ||Li 4 Ti 5 O 12 pouch cell with mass loading of 2.5 mAh/cm. Further, LiCl-LiBr-Graphite/Li full cells were designed with high energy density. Finally, we use a bi-layer design to enlarge the voltage window of aqueous electrolyte, which can endow the stable cycling of aqueous Lithium metal batteries.