Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cd annealing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Characterization of precipitates in CdTe and Cd(1-x)Zn(x)Te grown by vertical Bridgman-Stockbarger technique

Different polishing solutions were tested for exposing precipitates in CdTe and Cd(0.96)Zn(0.04) single crystals grown by vertical Bridgman-Stockbarger technique. A solution of 5-7% Br2 in methanol and E-solution were both effective. High resolution scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS) was employed to characterize those exposed precipitates. Most of the polyhedral-shaped Te precipitates with a size range from 3 to 20 microns had voids inside. Partially dissolved Te precipitates were observed in CdTe samples that had been annealed in Cd vapor at 700 C for 10 min. Isolated areas mis-oriented from the matrix were observed in CdTe and Cd(0.96)Zn(0.04)Te that had been annealed in Cd vapor at 700 C for 20 and 50 h, respectively. Te precipitate images were recorded with EDS. By SEM/EDS, Cd-rich precipitates were observed in some Cd-annealed CdTe. C and Na impurities were detected in some Te precipitates.

Shen, J.↗
NASA NTRS1987

II-VI and I-III-VI2 alloy crystals for photovoltaic applications

The results of the photoreflectance, photoconductivity, and photoluminescence studies on Mn(x)Cd(1-x)Te single crystals are discussed from the viewpoint of the utility of these compounds as gap components in multijunction solar cells. Attention is also given to recent results on CuInSe2 and on quaternary I-III-VI2 alloys based on CuInSe2. Recent Kelvin probe and X-ray photoemission spectroscopy studies of the surface properties of CuInSe2 and Mn(x)Cd(1-x)Te, respectively, are described. In addition, recent results on the radiation damage and annealing kinetics of Mn(x)Cd(1-x)Te are considered in the context of future work on the sputtering and ion beam deposition of thin films of this material.

Bachmann, K. J.↗
NASA NTRS1982

Defect chemistry and characterization of Hg sub 1x Cd sub x Te

Single crystal samples of undoped and doped Hg sub 1-x Cd sub x Te were annealed at varying temperatures and partial pressures of Hg. Hall effect and mobility measurements were carried out on these samples after quenching to room temperature. Based on the variation of the carrier concentration and the carrier mobility as a function of the partial pressure of Hg temperature, and dopant concentration, defect models were established for the doped and the undoped crystals. These models indicate that the native acceptor defects in both Hg0.8Cd0.2Te and Hg0.6Cd0.4Te doubly ionized and the native donor defects are negligible in concentration, implying that p to n conversion in these alloys occurs due only to residual donors. Incorporation mechanism of copper, indium, iodine, and phosphorus were investigated. A large concentration of indium is found to be paired with the native acceptor defects. Results on crystals doped with phosphorus indicate that phosphorus behaves amphoterically, acting as a donor on Hg lattice sites and as an acceptor intersitially on Te lattice sites. A majority of the phosphorus is found to be present as neutral species formed from the pairing reaction between phosphorus on Hg lattice sites and phosphorus in interstitial sites. Equilibrium constants for the intrinsic excitation reaction, as well as for the incorporation of the different dopants and the native acceptor defects were established.

Vydyanath, H. R.↗
NASA NTRS1981

Defect chemistry and characterization Hg(1-x)Cd(x)Te

Iodine doped single crystal samples of mercury cadmium telluride were annealed at temperatures varying from 450 C to 600 C in Hg vapor and quenched to room temperature. Hall effect measurements at 77 K on the crystals cooled to room temperature indicate the samples to be n-type after anneals at high Hg pressures whereas they turn p-type after anneals at low Hg pressures; the electron concentration increases with increase in Hg pressure. The results are explained on the basis that the crystals are saturated with (Hg,Cd)I2, with a fraction of the iodine being present as donor occupying tellurium lattice sites and a fraction being present as acceptors resulting from the iodine on tellurium lattice sites pairing with the doubly ionized native acceptor defects. The solubility of the donor species increases with increase in Hg pressure, whereas that of the acceptor species increases with decrease in Hg pressure. Equilibrium constants for the incorporation of the iodine species as well as the pairing reaction were established.

Vydyanath, H. R.↗
NASA NTRS1983

Mode of incorporation of phosphorus in Hg(0.8)Cd(0.2)Te

Selim and Kroeger (1977) have studied the mode of incorporation of phosphorus in CdTe. According to their findings, phosphorus behaves amphoterically in CdTe acting as an acceptor interstitially and on Te lattice sites, and as a triple donor on Cd lattice sites. The present investigation is concerned with the role of phosphorus in Hg(0.8)Cd(0.2)Te, taking into account Hall-effect and mobility measurements on phosphorus-doped crystals quenched from a temperature in the range from 450 to 600 C subsequent to anneals in different partial pressures of Hg. It is found that the behavior of phosphorus in Hg(0.8)Cd(0.2)Te is similar to that established for CdTe, except that all the electrically active phosphorus defect centers in Hg(0.8)Cd(0.2)Te appear to be only singly ionized. At low Hg pressure, phosphorus is incorporated as a single donor occupying Hg lattice sites, and at high Hg pressure, as a single acceptor on interstitial sites and Te lattice sites.

Vydyanath, H. R.↗
NASA NTRS1997

Photorefractivity in a Titanium Doped ZnCdTe Crystal

Single crystals of Zn(.04)Cd(.96)Te was grown by horizontal physical vapor transport (PVT) method and doped by annealing with TiTe2 powder at 600 C for six days. Photorefractive two-beam coupling, along with photoluminescence and absorption spectroscopy, were used to characterize the ZnCdTe:Ti crystal. At 1.32 micrometers, the photorefractive gain has been measured as a function of the grating period. A gain of about 0.16/cm was obtained at an intensity of about 0.1 W/sq cm. The results of this titanium doped ZnCdTe crystal are compared to that of vanadium-doped CdTe crystals reported previously.

Davis, M.↗
NASA NTRS1976

Photoluminescence of ion-implanted GaN

Thirty-five elements were implanted in GaN. Their photoluminescence spectra were measured and compared to those of an unimplanted control sample. Most impurities emit a peak at about 2.15 eV. Mg, Zn, Cd, Ca, As, Hg, and Ag have more characteristic emissions. Zn provides the most efficient recombination center. A set of midgap states is generated during the damage-annealing treatment.

Pankove, J. I.↗
NASA NTRS1981

Defect chemistry and characterization of (Hg, Cd)Te

Single crystal samples of phosphorus doped Hg sub 0.8 Cd sub 0.2 Te were anneald at temperatures varying from 450 C to 600 C in various Hg atmospheres. The samples were quenched to room temperature from the annealing temperatures. Hall effect and mobility measurements were performed at 77 K on all these samples. The results indicate the crystals to be p type for a total phosphorus concentration of 10 to the 19th power/cu cm in all the samples. The hole concentration at 77 K increases with increasing Hg pressures at 450 C and 500 C contrary to the observation in undoped crystals. Also, at low Hg pressures the concentration of holes in the phosphorus doped crystals is lower than in the undoped crystals. The hole concentration in all the samples is lower than the intrinsic carrier concentration at the annealing temperatures. The hole mobility in the doped crystals is similar to that in the undoped crystals. A defect model according to which phosphorus behaves as a single acceptor interstitially, occupying Te lattice sites while it acts as a single donor occupying Hg lattice sites was established. Equilibrum constants established for the incorporation of all the phosphorus species explain the experimental results

Vydyanath, H. R.↗
NASA NTRS1990

Study of surface passivation as a function of InP closed-ampoule solar cell fabrication processing variables

The effects of various surface preparation procedures, including chemical treatment and anodic or chemical oxidation, closed-ampoule diffusion conditions, and post-diffusion surface preparation and annealing conditions, on the passivating properties of InP have been investigated in order to optimize the fabrication procedures of n(+)p InP solar cells made by closed-ampoule diffusion of sulfur into p-type InP. The InP substrates used were p-type Cd-doped to a level of 1.7 x 10 to the 16th/cu cm, Zn-doped to levels of 2.2 x 10 to the 16th and 1.2 x 10 to the 18th/cu cm, and n-type S-doped to 4.4 x 10 to the 18th/cu cm. The passivating properties have been evaluated from photoluminescence (PL) and conductance-voltage (G-V) data. Good agreement was found between the level of surface passivation and the composition of different surface layers as revealed by X-ray photoelectron spectroscopy (XPS) analysis.

Faur, Mircea↗
NASA NTRS1994

Status of diffused junction p+n InP solar cells for space applications

Recently, we have succeeded in fabricating diffused junction p(sup +)n(Cd,S) InP solar cells with measured AMO, 25 C open circuit voltage (V(sub OC)) of 887.6 mV, which, to the best of our knowledge, is higher than previously reported V(sub OC) values for any InP homojunction solar cells. The experiment-based projected achievable efficiency of these cells using LEC grown substrates is 21.3 percent. The maximum AMO, 25 C internal losses due to date on bare cells is, however, only 13.2 percent. This is because of large external and internal losses due to non-optimized front grid design, antireflection (AR) coating and emitter thickness. This paper summarizes recent advances in the technology of fabrication of p(sup +)n InP diffused structures and solar cells, resulted from a study undertaken in an effort to increase the cell efficiency. The topics discussed in this paper include advances in: (1) the formation on thin p(sup +) InP:Cd emitter layers, (2) electroplated front contacts, (3) surface passivation and (4) the design of a new native oxide/Al2O3/MgF2 tree layer AR coating using a chemically-grown P-rich passivating oxide as a first layer. Based on the high radiation resistance and the excellent post-irradiation annealing and recovery demonstrated in the early tests done to date, as well as the projected high efficiency and low-cost high-volume fabricability, these cells show a very good potential for space photovoltaic applications.

Faur, Mircea↗
NASA NTRS1994

Status of Diffused Junction p(+)n InP Solar Cells for Space Applications

Recently, we have succeeded in fabricating diffused junction p(+)n(Cd,S) InP solar cells with measured AMO, 25 C open circuit voltage (V(sub OC)) of 887.6 mV, which, to the best of our knowledge, is higher than previously reported V(sub OC) values for any InP homojunction solar cells. The experiment-based projected achievable efficiency of these cells using LEC grown substrates is 21.3%. The maximum AMO, 25 C efficiency recorded to date on bare cells is, however, only 13.2%. This is because of large external and internal losses due to non-optimized front grid design, antireflection (AR) coating and emitter thickness. This paper summarizes recent advances in the technology of fabrication of p(+)n InP diffused structures and solar cells, resulted from a study undertaken in an effort to increase the cell efficiency. The topics discussed in this paper include advances in: 1) the formation of thin p(+) InP:Cd emitter layers, 2) electroplated front contacts, 3) surface passivation and 4) the design of a new native oxide/AI203/MgF2 three layer AR coating using a chemically-grown P-rich passivating oxide as a first layer. Based on the high radiation resistance and the excellent post-irradiation annealing and recovery demonstrated in the early tests done to date, as well as the projected high efficiency and low-cost high-volume fabricability, these cells show a very good potential for space photovoltaic applications.

Faur, Mircea↗
NASA NTRS2016

A Quantum-Assisted Algorithm for Sampling Applications in Machine Learning

An increase in the efficiency of sampling from Boltzmann distributions would have a significant impact in deep learning and other machine learning applications. Recently, quantum annealers have been proposed as a potential candidate to speed up this task, but several limitations still bar these state-of-the-art technologies from being used effectively. One of the main limitations is that, while the device may indeed sample from a Boltzmann-like distribution, quantum dynamical arguments suggests it will do so with an instance-dependent effective temperature, different from the physical temperature of the device. Unless this unknown temperature can be unveiled, it might not be possible to effectively use a quantum annealer for Boltzmann sampling. In this talk, we present a strategy to overcome this challenge with a simple effective-temperature estimation algorithm. We provide a systematic study assessing the impact of the effective temperatures in the learning of a kind of restricted Boltzmann machine embedded on quantum hardware, which can serve as a building block for deep learning architectures. We also provide a comparison to k-step contrastive divergence (CD-k) with k up to 100. Although assuming a suitable fixed effective temperature also allows to outperform one step contrastive divergence (CD-1), only when using an instance-dependent effective temperature we find a performance close to that of CD-100 for the case studied here. We discuss generalizations of the algorithm to other more expressive generative models, beyond restricted Boltzmann machines.

Perdomo-Ortiz, Alejandro↗
NASA NTRS1986

Sputtering and native oxide formation on (110) surfaces of Cd(1-x)Mn(x)Te

Native oxides on the surface of Cd(1-x)Mn(x)Te (X between 0 and 0.7) have been analyzed on the basis of X-ray photoemission spectroscopy measurements. Depth profile analysis revealed a significant increase in the thickness at higher Mn concentrations and a strong Mn segregation to the surface, respectively. Sputter-induced damage on cleaved (110)-oriented surfaces was analyzed by photoreflectance and photoluminescence measurements. The damage was found to be larger on CdTe than on the alloy. Thermal annealing showed nearly complete restoration for the surface of the alloy, while CdTe revealed irreversible modifications in the near-surface regime upon sputtering and post annealing.

Neff, H.↗