Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cell Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Evolution of oxygenated cadmium sulfide (CdS:O) during high-temperature CdTe solar cell fabrication

Oxygenated cadmium sulfide (CdS:O) produced by reactive sputtering has emerged as a promising alternative to conventional CdS for use as the n-type window layer in CdTe solar cells. Here, complementary techniques are used to expose the window layer (CdS or CdS:O) in completed superstrate devices and combined with a suite of materials characterization to elucidate its evolution during high temperature device processing. During device fabrication amorphous CdS:O undergoes significant interdiffusion with CdTe and recrystallization, forming CdS1-yTey nanocrystals whose Te fraction approaches solubility limits. Significant oxygen remains after processing, concentrated in sulfate clusters dispersed among the CdS1-yTey alloy phase, accounting for ~30% of the post-processed window layer based on cross-sectional microscopy. Interdiffusion and recrystallization are observed in devices with un-oxygenated CdS, but to a much lesser extent. Etching experiments suggest that the CdS thickness is minimally changed during processing, but the CdS:O window layer is reduced from 100 nm to 60-80 nm, which is confirmed by microscopy. Alloying reduces the band gap of the CdS:O window layer to 2.15 eV, but reductions in thickness and areal density improve its transmission spectrum, which is well matched to device quantum efficiency. The changes to the window layer in the reactive environments of device fabrication are profoundly different than what occurs by thermal annealing in an inert environment, which produced films with a band gap of 2.4 eV for both CdS and CdS:O. These results illustrate for the first time the significant changes that occur to the window layer during processing that are critical to the performance of CdTe solar cells.

14 SOLAR ENERGY↗

Comparative Study of Zn(O,S) Buffer Layers and CIGS Solar Cells Fabricated by CBD, ALD, and Sputtering: Preprint

Zn(O,S) thin films were deposited by chemical bath deposition (CBD), atomic layer deposition, and sputtering. Composition of the films and band gap were measured and found to follow the trends described in the literature. CBD Zn(O,S) parameters were optimized and resulted in an 18.5% efficiency cell that did not require post annealing, light soaking, or an undoped ZnO layer. Promising resultswere obtained with sputtering. A 13% efficiency cell was obtained for a Zn(O,S) emitter layer deposited with 0.5%O2. With further optimization of process parameters and an analysis of the loss mechanisms, it should be possible to increase the efficiency.

14 SOLAR ENERGY↗

An ant-nest-like cathode substrate for lithium-sulfur batteries with practical cell fabrication parameters

We report that electrochemical performances of lithium-sulfur batteries have received much progress in recent years. However, their practical deployment encounters challenges with respect to optimizing the cell-fabrication parameters (e.g., amounts of the active material and electrolyte). We present here an “ant-nest-like” cathode substrate with unique architecture to synchronously attain high electrochemical performance and necessary cell-fabrication parameters. The cells with a high sulfur loading (11.5 mg cm -2 ), a high sulfur content (75 wt.%), and a low electrolyte/sulfur ratio (9 μL mg -1 ) display a high areal capacity and energy density of, respectively, 7 mA h cm -2 and 14 mW h cm -2 with a capacity retention of 70% after 150 cycles. Moreover, the cells exhibit a low self-discharge behavior with a low self-discharge constant of 0.0013 per day and a long rest period of one month. Lastly, these dynamic and static electrochemical stabilities are attributed to the ant-nest-like structure and low surface area of the cathode substrate that allows, respectively, the accommodation and encapsulation of a high amount of active material and reduces the consumption of electrolyte.

25 ENERGY STORAGE↗

Nonradiative Recombination Dominates Voltage Losses in Cu(In,Ga)Se 2 Solar Cells Fabricated using Different Methods

Voltage losses reduce the photovoltaic conversion efficiency of thin‐film solar cells and are a primary efficiency limitation in Cu(In,Ga)Se 2 . Herein, voltage loss analysis of Cu(In,Ga)Se 2 solar cells fabricated at three institutions with variation in process, bandgap, absorber structure, postdeposition treatment (PDT), and efficiency is presented. Nonradiative voltage losses due to Shockley–Read–Hall charge carrier recombination dominate and constitute >75% of the total compared to <25% from radiative voltage losses. The radiative voltage loss results from nonideal absorption and carriers in band tails that stem from local composition‐driven potential fluctuations. It is shown that significant bulk lifetime improvements are achieved for all alkali PDT processed absorbers, chiefly associated with reductions in nonradiative recombination. Primary voltage loss contributions (radiative and nonradiative) change little across fabrication processes, but variation in submechanisms (bulk lifetime, net acceptor concentration, and interface recombination) differentiate nonradiative loss pathways in this series of solar cells.

14 SOLAR ENERGY↗

A Novel Technique for Performing PID Susceptibility Screening during the Solar Cell Fabrication Process

Various characterization techniques have historically been developed in order to screen potential induced degradation (PID)-susceptible cells, but those techniques require final solar cells. We present a new characterization technique for screening PID-susceptible cells during the cell fabrication process. Illuminated Lock-In Thermography (ILIT) was used to image PID shunting of the cell without metallization and clearly showed PID-affected areas. PID-susceptible cells can be screened by ILIT, and the sample structure can advantageously be simplified as long as the sample has the silicon nitride antireflection coating and an aluminum back surface field.

14 SOLAR ENERGY↗

Development of Novel RTP-like Processing for Solar Cell Fabrication using UV-Rich Light Sources: Cooperative Research and Development Final Report

NREL and Mattson Technology are interested in developing new processing techniques for fabrication of solar cells using UV-rich optical processing. UV light has a very high absorption coefficient in most semiconductors, allowing the semiconductor surface to be heated locally and, in some cases, without a significant increase in the substrate temperature. NREL has several projects related to cell processing that currently use an optical furnace (having a spectrum rich in visible and infrared light). Mattson Technology has developed a UV rich light source that can be used in either pulse or continuous modes. The objective of this CRADA is to explore applications in solar cell processing where absorption characteristics of UV light can lead to lower cell cost and/or higher efficiencies.

14 SOLAR ENERGY↗

Influence of Tabula Rasa on Process- and Light-Induced Degradation of Solar Cells Fabricated From Czochralski Silicon

Monocrystalline Si solar cells are fabricated from Czochralski (Cz) Si, which contains 10 17 –10 18 cm -3 oxygen atoms. Cz Si undergoes degradation during high-temperature thermal processing steps, such as dopant diffusion to form the p - n junction. This degradation in the bulk minority carrier lifetime can be related to the formation of oxygen precipitates. We found that a high-temperature annealing process known as tabula rasa (TR) not only mitigates process-induced degradation via oxygen precipitate nuclei dissolution, but also modifies subsequent light-induced degradation. We report on the bulk carrier lifetime of n - and p -type Cz Si after TR, which homogenizes the interstitial oxygen in the bulk Si to its monoatomic form in either an N 2 or O 2 environment. A control sample, which was not subjected to a TR processing step, experienced severe process-induced degradation during a boron emitter thermal budget as oxygen precipitates were formed in the Si bulk. These precipitates could be imaged using photoluminescence. Additionally, samples that underwent a TR processing step prior to the boron emitter thermal budget show efficient gettering of metallic impurities compared to the control sample, which showed a decline in the implied open-circuit voltage after the gettering step. Furthermore, modification of the interstitial oxygen bonding by TR had a strong effect on the light-induced degradation kinetics. Instead of a typically observed monotonic decrease, minority carrier lifetime increases first, followed by a nonmonotonic decrease over a ~20 h period. Finally, we conclude that by modifying the interstitial oxygen bonding via TR pretreatment, p -type Cz Si wafers become substantially resistant to harsh solar cell processes and strongly modified light-induced degradation, which would open alternative ways to mitigate this degradation mechanism.

14 SOLAR ENERGY↗

Photosensitivity of ZnO/CdS/Cu(In,Ga)Se{sub 2}/Mo thin-film solar cells fabricated on various substrates

The results of measuring the first spectra of relative quantum efficiency for photoconversion in thin-film ZnO/CdS/Cu(In,Ga)Se{sub 2}/Mo solar cells fabricated on rigid (glass) and flexible (polyimide) substrates are reported. The character of interband transitions has been studied and the values of the band gap for direct and indirect transitions in thin Cu(In,Ga)Se{sub 2} films are determined. It is found that a shift of the maximal photosensitivity for the obtained solar cells to shorter wavelengths is observed as rigid substrates are replaced by flexible ones. It is concluded that thin-film Cu(In,Ga)Se{sub 2} structures can be used as broad-band photoconverters of solar radiation.

36 MATERIALS SCIENCE↗

15.3% AM1.5G Efficiency GaAs Solar Cells Fabricated via an Epitaxy-Free Process

Here, we report simple and potentially low-cost techniques for creating high-quality n-type gallium arsenide (GaAs) and GaAs p/n junctions and fabricate GaAs p/n junction solar cells. Detailed-balance modeling suggests that 20% AM1.5G efficiency p/n homojunction devices may be possible if the surface doping concentration can be limited to values less than ∼ 5 × 10 19 cm −3 . Our process exploits an open-tube, vapor-phase, deposition-free, zinc diffusion technique for forming p-type layers in melt-grown n-GaAs substrates that results in sheet resistances less than 1 kΩ/$\square$. In addition, we have improved the minority carrier diffusion lengths of melt-grown GaAs from less than one micron to over five microns using an open-tube, vacuum-free, annealing process which reduces the density of EL2 midgap defects. Finally, we have combined these advances to fabricate epitaxy-free, GaAs solar cells with a validated AM1.5G efficiency of 15.3%.

14 SOLAR ENERGY↗

Thermally evaporated methylammonium tin triiodide thin films for lead-free perovskite solar cell fabrication

Here, we report on the synthesis of methylammonium tin triiodide (MASnI 3 ) thin films at room temperature by a hybrid thermal evaporation method and their application in fabricating lead (Pb)-free perovskite solar cells. The as-deposited MASnI 3 thin films exhibit smooth surfaces, uniform coverage across the entire substrate, and strong crystallographic preferred orientation along the < 100 > direction. By incorporating this film with an inverted planar device architecture, our Pb-free perovskite solar cells are able to achieve an open-circuit voltage ( V oc ) up to 494 mV. The relatively high V oc is mainly ascribed to the excellent surface coverage, the compact morphology, the good stoichiometry control of the MASnI 3 thin films, and the effective passivation of the electron-blocking and hole-blocking layers. Finally, our results demonstrate the potential capability of the hybrid evaporation method to prepare high-quality Pb-free MASnI 3 perovskite thin films which can be used to fabricate efficient Pb-free perovskite solar cells.

14 SOLAR ENERGY↗

Optical properties of multi-stacked InGaAs/GaNAs quantum dot solar cell fabricated on GaAs (311)B substrate

Quantum dot solar cells (QDSCs) comprised of 10 stacked pairs of strain-compensated InGaAs/GaNAs QD structure have been fabricated by atomic hydrogen-assisted molecular beam epitaxy. A homogeneous and high-density QD array structure with improved in-plane ordering and total density of {approx}10{sup 12} cm{sup -2} has been achieved on GaAs (311)B grown at 460 Degree-Sign C after stacking. The external quantum efficiency (EQE) of InGaAs/GaNAs QDSC increases in the longer wavelength range due to additive contribution from QD layers inserted in the intrinsic region. The short-circuit current density measured for QDSC is 17.2 mA/cm{sup 2} compared to 14.8 mA/cm{sup 2} of GaAs reference cell. Further, an increase in EQE due to photocurrent production by 2-step photon absorption has been observed at room temperature though it is still small at around 0.1%.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Ablation of film stacks in solar cell fabrication processes

A dielectric film stack of a solar cell is ablated using a laser. The dielectric film stack includes a layer that is absorptive in a wavelength of operation of the laser source. The laser source, which fires laser pulses at a pulse repetition rate, is configured to ablate the film stack to expose an underlying layer of material. The laser source may be configured to fire a burst of two laser pulses or a single temporally asymmetric laser pulse within a single pulse repetition to achieve complete ablation in a single step.

36 MATERIALS SCIENCE↗

Investigating the Effect of Lamination on FAMACs: Toward a New Phase Space of Perovskite Solar Cell Fabrication

The rapid progress in the field of perovskite solar cells has led to efficiencies approaching that of crystalline silicon in single junction devices, and increasing emphasis is now being placed on scalable fabrication strategies that have the potential to truly impact the photovoltaics industry. The standard fabrication route of sequential, layer-bylayer depositions to form the device stack is limited by the small range of selective materials that can withstand successive solvent exposures and thermal annealings. In order to overcome this limitation, we have developed a method to fabricate the device stacks through mechanical lamination under moderate pressures and temperatures. The procedure involves fabricating two transparent conductive oxide/transport material/perovskite half stacks and laminating them together at the perovskite/perovskite interface. This procedure previously achieved 10% efficiency in initial attempts based on methyl ammonium lead iodide (MAPI) perovskite compositions. Herein, we reported the fabrication conditions to achieve a reproducible lamination with a complex, multi-cation perovskite, [Cs0.05(MA0.17F A0.83)0.95P b(I0.83Br0.17)3] (FAMACs), laminated at 18 degrees C and with a pressure of 350 psi for 30 minutes. The resulting material showed a sharpening of the optical absorption edge and a slight reduction in the band gap from 1.622 eV to 1.616 eV, indicative of improved ordering and reduced defects. Concurrently, time resolved photoluminescence measurements revealed an increased luminescence lifetime from 85 ns to 123 ns.

14 SOLAR ENERGY↗

Nanopinhole Passivating Contact Si Solar Cells Fabricated with Metal-Assisted Chemical Etching

Monocrystalline Si (c-Si) solar cells with passivating contacts based on doped polycrystalline Si (poly-Si) on ≈2.0 nm silicon oxide (SiO x ) require >1000 °C thermal processing to create conducting pinholes in the SiO x layer. However, this high thermal budget can induce bulk defects in the Czochralski c-Si wafers used as the cell absorber layer. We demonstrate that pinholes can instead be created using metal-assisted chemical etching on planar or textured morphologies, at room temperature. This wet process creates up to 200 nm wide conducting pinholes that are directly observed with transmission electron and atomic force microscopies. High-performance hole-selective poly-Si/SiN y /SiO x and electron-selective poly-Si/SiO x passivating contacts are fabricated and implemented in laboratory-scale solar cells. This process development significantly broadens the range of passivation layer materials, their thicknesses, and surface morphologies, which enables the design of poly-Si contacts with superior passivating quality.

14 SOLAR ENERGY↗

Effects of transparent conducting electrodes and hole transport layers on the performance of MAPbI 3 solar cells fabricated on PET substrates

Abstract This study investigates how the performance of perovskite solar cells (PSCs) made on polyethylene terephthalate (PET) substrates depends on transparent conducting electrodes (TCEs) and hole transport layers (HTLs). We fabricated PSCs using commercially available PET/TCEs and compared their performance with PSCs manufactured on Glass/indium tin oxide (ITO) substrates. Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) with varying levels of acidity and NiO nanoparticles were used as HTLs. The current density-voltage characteristics of PSCs made on PET/TCEs were found to be significantly lower when highly acidic PEDOT:PSS was used as the HTL. However, this was not observed for PSCs made on Glass/ITO. To investigate the interaction between HTL and TCE, atomic force microscopy was carried out after dipping the TCEs in PEDOT:PSS solutions of different acidity. X-ray photoelectron spectroscopy measurements further revealed differences in the chemical composition between ITO film on PET vs. on glass. Our results indicate that the performance of PSCs depends both on the TCE substrates and HTLs, which can be explained by their chemical interaction.

14 SOLAR ENERGY↗

Improved Efficiency and Stability of Pb/Sn Binary Perovskite Solar Cells Fabricated by Galvanic Displacement Reaction

In this work, a simple and generally applicable method of fabricating efficient and stable Pb-Sn binary perovskite solar cells (PVSCs) based on a galvanic displacement reaction (GDR) is demonstrated. Different from the commonly used conventional approaches to form perovskite precursor solutions by mixing metal halides and organic halides such as PbI 2 , SnI 2 , MAI, FAI, etc., together, the precursor solutions are formulated by reacting pure Pb-based perovskite precursor solutions with fine Sn metal powders. After the ratios between Pb and Sn are optimized, high PCEs of 15.85% and 18.21% can be achieved for MAPb 0.4 Sn 0.6 I 3 and (FAPb 0.6 Sn 0.4 I 3 ) 0.85 (MAPb 0.6 Sn 0.4 Br 3 ) 0.15 based PVSCs, which are the highest PCEs among all values reported to date for Pb-Sn binary PVSCs. Moreover, the GDR perovskite-based PVSCs exhibit significantly improved ambient and thermal stability with encapsulation, which can retain more than 90% of their initial PCEs after being stored in ambient (relative humidity (RH) ≈50%) for 1000 h or being thermal annealed at 80 °C for more than 120 h in ambient conditions. These results demonstrate the advantage of using GDR to prepare tunable bandgap binary perovskites for devices with greatly improved performance and stability.

36 MATERIALS SCIENCE↗