Search NASA⌕ Search

SEARCH · Search NASA

Results for “Co-Evaporation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Ellipsometric study of YBa2Cu3O(7-x) laser ablated and co-evaporated films

High temperature superconducting films of YBa2Cu3O(7-x) (YBCO) were grown on SrTiO3, LaAl03, and YSZ substrates using two techniques: excimer laser ablation with in situ annealing and co-evaporation of Y, Cu, and BaF2 with ex-situ annealing. Film thicknesses were typically 5000 A, with predominant c-axis alignment perpendicular to the substrate. Critical temperatures up to Tc(R = 0) = 90 K were achieved by both techniques. Ellipsometric measurements were taken in the range 1.6 to 4.3 eV using a variable angle spectroscopic ellipsometer. The complex dielectric function of the laser ablated films was reproducible from run to run, and was found to be within 10 percent of that previously reported for (001) oriented single crystals. A dielectric overlayer was observed in these films, with an index of refraction of approximately 1.55 and nearly zero absorption. For the laser ablated films the optical properties were essentially independent of substrate material. The magnitude of the dielectric function obtained for the co-evaporated films was much lower than the value reported for single crystals, and was sample dependent.

Alterovitz, S. A.↗
NASA NTRS1990

Ellipsometric study of YBa2Cu3O(7-x) laser ablated and co-evaporated films

High temperature superconducting films of YBa2Cu3O(7-x) (YBCO were grown on SrTiO3, LaA1O3, and YSZ substrates using two techniques: excimer laser ablation with in situ annealing and co-evaporation of Y, Cu, and BaF2 with ex-situ annealing. Film thicknesses were typically 5000 A, with predominant c-axis alignment perpendicular to the substrate. Critical temperatures up to Tc(R=O)=90 K were achieved by both techniques. Ellipsometric measurements were taken in the range 1.6 to 4.3 eV using a variable angle spectroscopic ellipsometer. The complex dielectric function of the laser ablated films was reproducible from run to run, and was found to be within 10 percent of that previously reported for (001) oriented single crystals. A dielectric overlayer was observed in these films, with an index of refraction of approximately 1.55 and nearly zero absorption. For the laser ablated films the optical properties were essentially independent of substrate material. The magnitude of the dielectric function obtained for the co-evaported films was much lower than the value reported for single crystals, and was sample dependent.

Alterovitz, S. A.↗
NASA NTRS1993

Microwave properties and characterization of co-evaporated BSCCO thin films

An extensive characterization of Bi-Sr-Ca-Cu-O (BSCCO) thin films deposited by co-evaporation on LaAlO3 and SrTiO3 substrates was performed. The films had a T(sub c) (R = O) of approximately 78 K, and were predominantly c-axis oriented, with critical current densities (J(sub c)) at 4.5 K of 1.6 x 10(exp 6) and 1.1 x 10(exp 6) A cm(sup -2), for the samples on SrTiO3 and LaAlO3, respectively. The microwave properties of the films were examined by three techniques. The complex conductivity sigma(sub *) = sigma(sub 1) - j(sigma(sub 2)) and the magnetic penetration depth (A) were measured by power transmission at 30.6 GHz; the surface resistance (R(sub s)) was measured using a cavity resonator at 58.9 GHz, and the transmission line losses were determined by measuring the quality factor (Q) of a linear microstrip resonator at 10.4 and 20.2 GHz. The complex conductivity for the film on LaAlO3 was determined to be (2.0-j10) x 10(exp 5) S/m at 77 K. It was observed that in the superconducting state sigma(sub 1) deviates from both the Bardeen-Cooper-Schrieffer (BCS) theory and the two-fluid model. Values of lambda were found to be approximately 2.0 and 1.1 microns at 77 K and 20 K respectively, and were obtained for the film on LaAlO3. The value of lambda at 20 K was approximately three times larger than that of BSCCO single crystals. R(sub s) values of 865 and 1391 mOmega were obtained for the films on SrTiO3 and LaAlO3, respectively, at 77 K and 58.9 GHz. Unloaded Q factors at 20 K of approximately 1100 and 800 at 10.4 and 20.2 GHz respectively, were measured for the BSCCO resonator. Unloaded Q values of 290 and 405 at 20 K were obtained at 10.4 GHz and 20.2 GHz respectively, for an all gold (Au) resonator.

Miranda, F. A.↗
DOE OSTI2023

Solutions Are the Problem: Ordered Two-Dimensional Covalent Organic Framework Films by Chemical Vapor Deposition

Covalent organic frameworks (COFs) are a promising class of crystalline polymer networks that are useful due to their high porosity, versatile functionality, and tunable architecture. Conventional solution-based methods of producing COFs are marred by slow reactions that produce powders that are difficult to process into adaptable form factors for functional applications, and there is a need for facile and fast synthesis techniques for making crystalline and ordered covalent organic framework (COF) thin films. In this work, we report a chemical vapor deposition (CVD) approach utilizing co-evaporation of two monomers onto a heated substrate to produce highly crystalline, defect-free COF films and coatings with hydrazone, imine, and ketoenamine COF linkages. Further, this all-in-one synthesis technique produces highly crystalline, 40 nm–1 μm-thick COF films on Si/SiO2 substrates in less than 30 min. Crystallinity and alignment were proven by using a combination of grazing-incidence wide-angle X-ray scattering (GIWAXS) and transmission electron microscopy (TEM), and successful conversion of the monomers to produce the target COF was supported by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and UV–vis measurements. Additionally, we used atomic force microscopy (AFM) to investigate the growth mechanisms of these films, showing the coalescence of triangular crystallites into a smooth film. To show the wide applicability and scope of the CVD process, we also prepared crystalline ordered COF films with imine and ketoenamine linkages. These films show potential as high-quality size exclusion membranes, catalytic platforms, and organic transistors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

High Semi-Volatile Organic Aerosol Contributions Associated with Ammonium Nitrate in the Coastal Urban Environment

Organic components often contribute 50% or more of the submicron aerosol mass in coastal urban environments, but their partitioning between the gas and particle phases is controlled by a complex mixture of unidentified organic compounds that are poorly constrained by observations. This study compares daily filter organic functional groups (OFG) with online organic mass fragments from La Jolla, California, as part of the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), quantifying the contributions of four types of non-volatile (NV) organic emission sources to the submicron composition. Daily filters retained only 0.79–0.98 µg/m3 NV submicron organic mass concentration, even though 1.8–1.9 µg/m3 non-refractory (NR) submicron organic mass concentration was measured online. The 62–64% of measured NR submicron organic mass concentration that exceeded what remained on the filters after 23-hr sampling is interpreted as semi-volatile, consistent with the moderate correlation of the NR NV difference to NR ammonium, NR nitrate, and biomass burning-related NV and NR organic factors. The association between semi-volatile organic components and ammonium nitrate likely results from both co-emission and co-evaporation. Size-resolved filter analysis showed that NV organic mass concentration accounts for 68% of NR organic mass concentration for 0.5–1 µm dry diameter but account for 9.0% for 0.18–0.5 µm dry diameter showing the differences in volatility between particle modes. Importantly, volatility of organic components was size-dependent Information Classification: General and associated with ammonium nitrate and biomass burning, providing guidance for constraining atmospheric aerosol properties in global models.

Pelayo, Christian↗
DOE OSTI2022

Grain Enhancement in Polycrystalline CuGaSe 2 by AgBr Vapor Treatment

Copper Gallium diselenide (CuGaSe 2 or CGS) thin film were deposited using a three-stage thermal co-evaporation process on molybdenum coated soda lime glass. Recrystallization was carried after the second stage by flashing AgBr for 2 mins. The change in morphology, structure and depth profile were studied after the treatment. SEM and XRD showed an increase in grain size and enhanced crystallinity. Here, a decrease in sodium profile after the treatment was observed through SIMS measurements. Overall, AgBr treatment of CGS seems to be promising for the improvement of film quality, which could help with enhanced device fabrication in the future.

14 SOLAR ENERGY↗
DOE OSTI2022

On the Effect of Indium Chloride Dose on the Recrystallization of Cu(In,Ga)Se 2 Thin Films and associated Devices

Cu(In,Ga)Se 2 thin films deposited by a single-stage co-evaporation process at 350 ºC on molybdenum coated soda lime glass substrate were annealed post-deposition in InCl 3 vapor. The amount of InCl 3 and Se was varied. Here, the annealing treatment was done at 450 ºC for 30 minutes. Increase in grain size was observed after the treatment in all cases by X-ray diffraction. Device performance was low, but improved slightly after KCN etching.

14 SOLAR ENERGY↗
DOE OSTI2022

Effect of Metal Halides Treatment on High Throughput Low Temperature CIGS Solar Cells

Copper indium gallium diselenide (CIGS) semiconductor thin films were deposited at high rate and low temperature using single-stage thermal co-evaporation process on molybdenum back contact. A post deposition treatment was done by flashing AgBr at 350 ºC to induce recrystallization. Changes in morphology were confirmed by SEM, with an observed increase in grain size, as well as by XRD measurements, with a decrease in FWHM. Device results show an improvement of the performance after the AgBr vapor treatment, as all the photovoltaic parameters enhanced. Altogether, AgBr seems to be a suitable transport agent and beneficial for device fabrication.

14 SOLAR ENERGY↗
DOE OSTI2022

Post-deposition Metal Halide Treatment of CuGaSe 2 for Photovoltaic Application

Copper gallium diselenide (CGS) semiconductor thin films were deposited by three-stage thermal co-evaporation process. Post-deposition treatments and recrystallization were performed at various AgBr doses of 40 mg, 60 mg, and 80 mg after the 2 nd stage. The changes in surface morphology were confirmed by SEM. The electrical properties were also modified, as the resistivity of the film decreases with increasing doses. Here, the device performance after the treatment did not change as expected, as the overall device performance only slightly increases in the case of 60 mg of AgBr. Substantial changes in the fabrication process will therefore be required for better device results.

14 SOLAR ENERGY↗
DOE OSTI2022

Low refractive index OLEDs for practical high-efficiency outcoupling. Final report

Improving OLED light extraction is a significant on-going challenge for the OLED lighting industry. The goal of this program was to explore the potential to improve internal light extraction in a manufacturable way by lowering the refractive index of the OLED stack through dilution with an electrically-inert, low refractive index molecule. We accomplished this goal, identifying a small molecule that can be co-evaporated in the hole transport layer of OLEDs at high loading to reduce the refractive index by 0.2-0.3 refractive index units without degrading charge transport. Implementing this dilution molecule in the hole transport layer of a range of single and multi-stack OLEDs, we demonstrated the ability to improve their internal light extraction by up to ~35% without increasing their drive voltage or reducing their operational lifetime. Importantly, these findings extend to state-of-the-art device architectures with proprietary OLED materials.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Measurements and Analyses to Enable Science for the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE)

Coastal cities provide the opportunity to characterize the substantial effects of manmade particles on marine cloud properties and processes. La Jolla lies to the north of San Diego, California, but it is often about a day directly downwind of the major pollution sources located in the ports of Los Angeles and Long Beach. The large dynamic range of aerosol particle concentrations combined with the multi-hour to multi-day persistence of stratocumulus cloud layers makes the site ideal for investigating the seasonal changes in cloud and aerosol properties as well as the quantitative relationships between cloud and aerosol properties. The Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE) characterized the extent, radiative properties, aerosol interactions, and precipitation characteristics of stratocumulus clouds in the Eastern Pacific across all four seasons at two coastal sites in La Jolla. This project was designed to enhance and expand the scientific uses of the ARM AMF1 measurements from EPCAPE. The goal was to ensure meaningful observations were collected that would enable science. The project included the following objectives: (1) Reviewing the ARM AMF1 measurements [ARM, 2021a; b] and circulating a summary of the measurements each week, (2) Comparing AMF1 measurements to those provided by collaborators (including filter measurements at the pier), (3) Collecting and analyzing filter samples from Scripps Pier by Fourier Transform Infrared spectroscopy (FTIR) and X-ray Fluorescence (XRF), (4) Assisting in operations of instruments provided by Guest PIs when possible, and (5) Providing an initial compilation of EPCAPE aerosol and cloud seasonal differences. The expected outcomes of these objectives were enhanced proposals and publications using EPCAPE measurements by helping to identify instrument issues, expanded data access and awareness by distributing weekly plots and related summaries, improved source-related attribution of aerosols with elemental tracers, additional observations provided by Guest PIs, and accelerated ACI studies enabled by the compiled seasonal summaries of aerosol and cloud properties. Three examples of the science enabled by this project are findings that (i) aerosol and cloud aqueous production contributes more than half of sulfate particle mass concentration, (ii) upwind sources make chemical composition very similar at nearby sites despite local differences in meteorology, and (iii) most of the large mass concentration of semi-volatile organic components is co-emitted and co-evaporated with nitrate. Together these findings illustrate how ARM extended field campaigns in coastal regions can be used to constrain ACI processes with direct observations. By using the unique ARM suite of cloud radiative products in addition to the measured aerosol properties at a coastal location, we were able to address the more specific question of which aerosol particles cause how much of the effects on clouds. Identifying this signature in coastal areas provides an opportunity to test the representation of aerosol sources by global models in a range of clean and urban-influenced conditions.

Russell, Lynn [Univ. of California, San Diego, CA ↗
NASA NTRS1975

Cadmium sulfide solar cells

Development, fabrication and applications of CdS solar cells are reviewed in detail. The suitability of CdS cells for large solar panels and microcircuitry, and their low cost, are emphasized. Developments are reviewed by manufacturer-developer. Vapor phase deposition of thin-film solar cells, doping and co-evaporation, sputtering, chemical spray, and sintered layers are reviewed, in addition to spray deposition, monograin layer structures, and silk screening. Formation of junctions by electroplating, evaporation, brushing, CuCl dip, and chemiplating are discussed, along with counterelectrode fabrication, VPD film structures, the Cu2S barrier layer, and various photovoltaic effects (contact photovoltage, light intensity variation, optical enhancement), and various other CdS topics.

Stanley, A. G.↗
NASA NTRS1978

Reactively evaporated films of copper molybdenum sulfide

Films of superconducting Chevrel-phase copper molybdenum sulfide CuxMo6S8 were deposited on sapphire substrates by reactive evaporation using H2S as the reacting gas. Two superconducting temperatures (10.0 K and 5.0 K) of the films were found, corresponding to two different phases with different copper concentrations. All films were superconducting above 4.2 K and contained Chevrel-phase compound as well as free molybdenum. The critical current was measured as a function of applied field. One sample was found to deviate from the scaling law found for co-evaporated or sputtered samples, which possibly indicates a different pinning mechanism or inhomogeneity of the sample.

Chi, K. C.↗
DOE OSTI2022

Downhole laser system with an improved laser output production and data collection

One or more embodiments relates to a method of growing ultrasmooth and high quantum efficiency CsTe photocathodes. The method includes exposing a substrate of Cs using an alkali source such as an effusion cell; and controlling co-evaporating growth and co-deposition forming a CsTe growth. The method further includes monitoring a stoichiometry of the CsTe growth.

Mcintyre, Dustin↗
DOE OSTI2024

Investigation of properties of CdSeTe/Sb and Sb/CdSeTe stacks

The effect of Sb inclusion in CdSeTe thin films was examined. CdSeTe alloys were grown by co-evaporation, either on 5 nm thick electron-beam evaporated Sb layers (Sb/CdSeTe) or coated with Sb post-deposition (CdSeTe/Sb). Sb inclusion improved CdSeTe grain structure, a critical factor for device performance, with average grain size increasing from 0.6 to 1.5 μm. All samples crystallized on annealing to the cubic structure, with a change in film orientation from (111) to random or (220). The presence of Sb in CdSeTe/Sb or Sb/CdSeTe samples, however, had a limited effect on the carrier concentration compared to Sb-free samples. Time resolved photoluminescence showed Sb inclusion increased decay lifetimes, with τ1 = 0.8 ns for and τ2 = 6.9 ns for the Sb/CdSeTe sample.

14 SOLAR ENERGY↗
DOE OSTI2024

Downhole laser system with an improved laser output production and data collection

One or more embodiments relates to a method of growing ultrasmooth and high quantum efficiency CsTe photocathodes. The method includes exposing a substrate of Cs using an alkali source such as an effusion cell; and controlling co-evaporating growth and co-deposition forming a CsTe growth. The method further includes monitoring a stoichiometry of the CsTe growth.

McIntyre, Dustin↗
DOE OSTI2022

Homogeneous CuGaSe 2 growth by the CuPRO process with In-Situ AgBr treatment

Homogeneous CuGaSe 2 thin film growth is limited by slow kinetics of formation. A modified growth process was previously developed to address this issue but requires two separate long, high temperature anneals. Here, we demonstrate that a short AgBr treatment can replace this modified growth process. The AgBr works as a transport agent to catalyze CuGaSe 2 formation and atomic mobility. Furthermore, this treatment results in large grains with homogeneous composition through the bulk. Solar cells made with this material show better performance.

14 SOLAR ENERGY↗