Results for “Coal Specifications”

DOE OSTI2019

Quality Guidelines for Energy System Studies: Detailed Coal Specifications

Specifications for selected feedstocks that are commonly found in the National Energy Technology Laboratory (NETL)-sponsored energy system studies are summarized in NETL’s “Quality Guidelines for Energy System Studies” (QGESS). The purpose of this companion section is to document default QGESS specifications for coal compositions reflecting a spectrum of seven coal ranks: North Dakota (ND) lignite; Texas (TX) lignite; “super-compliance” subbituminous, ~0.2 percent sulfur (as-received weight percent); subbituminous, > 0.5 percent sulfur(as-received weight percent); high volatile bituminous; medium volatile bituminous; low volatile bituminous.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Investigating Benefits and Challenges of Converting Retiring Coal Plants into Nuclear Plants

A coal-to-nuclear (C2N) transition means siting a nuclear reactor at the site of a recently retired coal power plant. Three overarching questions from the C2N transition guide this research: where in the United States are retired coal facilities located and what factors make a site feasible for transition; what factors of technology, cost, and project timeline drive investor economics over such a decision; and how will C2N impact local communities? The study team evaluated the siting characteristics of recently retired plants and those operating coal-fired power plant sites run by a utility or an independent power producer utilizing publicly available data to screen U.S. coal power plant sites to nuclear-feasible locations. After screening all retired coal sites to a set of 157 potential candidates and screening operating sites to a set of 237 candidates, the study team estimates that 80% of retired and operating coal power plant sites that were evaluated have the basic characteristics needed to be considered amenable to host an advanced nuclear reactor. For the recently retired plant sites evaluated, this represents a capacity potential of 64.8 GWe to be backfit at 125 sites. For the operating plant sites evaluated, this represents a capacity potential of 198.5 GWe to be backfit at 190 sites. This report evaluates a case study for the detailed impacts and potential outcomes from a C2N transition. Based on the nuclear technology choices and sizes evaluated to replace a large coal plant of 1,200 MWe generation capacity at the case study site, nuclear overnight costs of capital could decrease by 15% to 35% when compared to a greenfield construction project, through the reuse of infrastructure from the coal facility. Nuclear replacement designs can have a lower capacity size because nuclear power plants run at higher capacity factors than coal power plants. In the case study replacing coal capacity with 924 GWe of nuclear capacity, the study team found regional economic activity could increase by as much as $\$275 million$ and add 650 new, permanent jobs to the region of analysis. The evaluated site choice in the report is hypothetical for analysis purposes only and based on available data and documented assumptions. Consequently, the findings only inform at a general level. A community, investor, or other interested stakeholder can use these results to set up a detailed, in-depth analysis for a specific application of interest, such as evaluating a C2N transition of a specific coal power plant and a specific nuclear technology design. The report was subjected to independent peer reviews by experts in systems engineering and regional economic modeling to evaluate analysis and assumptions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

New coal char-based bricks: Effects of curing temperature, humidity, pressing pressure, and addition of superplasticizer on the physical, mechanical, and thermal properties

Coal char, as a sustainable and eco-friendly material, holds significant potential for use in new construction materials, specifically, coal char-based bricks. This study employed the pre-pressing method to create char bricks containing high char content of 70%. The impact of various curing temperatures (20, 40, 60 °C), humidity levels (15% and 90%), and pressing pressures (3.5, 7, and 10 MPa) on the density, X-ray diffraction, compressive strength, and thermal conductivity of char-based samples were examined. The addition of superplasticizer and the performance of char bricks were assessed by comparing them to traditional clay bricks and corresponding standards. The study discovers that the temperature of 40 °C enhances the early 7-day strength of char brick samples, while the highest 28-day strength is observed in char bricks at a temperature of 20 °C and humidity of 90%. Compared to conventional clay bricks (with density of 1.9 g/cm3, thermal conductivity of 0.39-0.63 W/mK, compressive strength of 10-20 MPa), the proposed char bricks exhibit lower density (~0.8 g/cm 3 ), lower thermal conductivity (0.26-0.35 W/mK), and good performance in compressive strength (up to 15 MPa). Lastly, coal char-based bricks with high char content demonstrate significant advantages over traditional clay bricks, making them a sustainable and environmentally friendly building material option.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Carbon Electrodes from Powder River Basin Coal Development of Competitive Supercapacitor Electrodes of Diverse Compositions from Coal Extract

Recent demand for coal as a thermal energy source has decreased significantly and will likely continue to decrease as renewable sources of energy become more available and environmental concern and cost from burning coal makes it more costly than renewables. Given that Powder River Basin (PRB) coal in Wyoming has relatively low thermal energy, it is critical for Wyoming to employ coal in other capacities at the current energy transition period in history. Among many potential non-thermal applications, PRB coal can be utilized for membrane and electrode applications through the formation of carbon fibers. Coal-derived membranes can become low-cost, conductive membranes for use in electrodialysis separation processes. Carbon fiber derived electrodes have been shown be a cost-effective alternative to typical electrode materials that can meet or exceed the performance of current carbon electrode materials. In this talk, we demonstrate the manufacture of supercapacitor electrodes from Powder River Basin (PRB) coal-derived precursors. Specifically, PRB coal was treated in cheap solvents, partitioned into liquid extract and solid residue. An electropinning process has been developed that can convert either the liquid extract or the solid residue into carbon fiber mats. The electrospinning process is versatile with many tunable process parameters to achieve desirable physiochemical properties. For example, the coal residue can be manipulated by additional heat treatment, or by adding binders, salts, or surfactants to create a solution that can be electrospun into advanced carbon electrodes with desirable structural and surface properties. Similarly, some of the liquid extract (tar fraction) can be subsequently reacted with toluene diisocyanate to create resinous coal-derived polyurethane (PUs) as a spinnable ink. Carbon nanofiber mats made from our proprietary electrospinning process were further carbonized at temperature ranging from 700°C to 900°C before they are used as electrodes in supercapacitors. Galvanostatic charge-discharge (GCD) results show that the best performing PU fiber mats can deliver a specific capacitance of 604 F g -1 at the current density of 1 A g -1 . A carbon fiber mat from a different solvent extraction residue also delivered the specific capacitance of 508 F g -1 . These specific capacitance values are comparable to or better than commercial activated carbons, demonstrating the viability of manufacturing carbon nanofiber electrodes from coal without the use of a commercial polymer as binder in the spinning ink.

Cincotta, Robert↗

DOE OSTI2025

Tunable electrochemical pathway for high-purity REMs and CMs

This report details a comprehensive research initiative focused on developing a technical research plan for the efficient and sustainable production of rare earth elements (REEs) and critical materials (CMs) from coal-based resources, specifically lignite coal from the Williston Basin in North Dakota. The project’s methodology centers on the design and evaluation of a tunable electrochemical pathway (TEP), an innovative approach aimed at achieving high-purity rare earth oxides (REOs), rare earth salts (RES), and CMs. This research is crucial for addressing the growing demand for these materials in clean energy technologies, electric vehicles, and high-tech applications, while reducing the United States’ reliance on foreign supply chains.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Tunable Electrochemical Pathway for High-Purity REMs and CMs

This report details a comprehensive research initiative focused on developing a technical research plan for the efficient and sustainable production of rare earth elements (REEs) and critical materials (CMs) from coal-based resources, specifically lignite coal from the Williston Basin in North Dakota. The project’s methodology centers on the design and evaluation of a tunable electrochemical pathway (TEP), an innovative approach aimed at achieving high-purity rare earth oxides (REOs), rare earth salts (RES), and CMs. This research is crucial for addressing the growing demand for these materials in clean energy technologies, electric vehicles, and high-tech applications, while reducing the United States’ reliance on foreign supply chains. The project was structured into four key tasks, each designed to build upon the previous one and contribute to the overarching goal of developing a viable technical research plan.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

The Role of State Utility Regulators in a Just and Reasonable Energy Transition: Examining Regulatory Approaches to the Economic Impacts of Coal Retirements

The ongoing trend of coal retirements has disproportionately affected the socioeconomic health of communities where power plants are located. For many public utility commissions, these impacts have led to important questions around the scope of PUCs’ statutory authority to analyze, consider and mitigate losses to host communities within their role as utility regulators. Due largely to variations in state legislative charges, commissions have taken different approaches to articulating what lies within the public interest.This report examines the authority of PUCs across the country to consider non-energy economic impacts beyond direct ratepayer effects, and summarizes approaches that PUCs, utilities and other stakeholders have used to mitigate the economic fallout of coal retirements, specifically.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2020

A new approach of reduction of carbon dioxide emission and optimal use of carbon and hydrogen content for the desired syngas production from coal

We report this research is designed to make progress in overcoming the challenges through the development of a two-stage coal processing. Specifically, a two-stage process was used to maximize the use of the carbon in coal or increase the carbon monoxide yield or lower carbon dioxide and methane yields. Carbon dioxide-char gasification in the absence of water can generate carbon monoxide with near-zero methane, which is desired to produce high-carbon and low-hydrogen chemicals such as oxalic acid through catalytic carbon monoxide coupling and hydrolysis. The technology is applicable to any coal, although Power River Basin (PRB) coal is used as an example feedstock in this research Also, the sodium-iron catalyst can accelerate not only the reaction kinetics in both stages but also increase the hydrogen/carbon monoxide ratio in the syngas produced in the second stage. In other words, the catalyst is a multifunctional agent, which can not only intensify the overall coal process efficiency but also improve the qualities of the desired syngas products and reduce carbon dioxide emission. Thus, In the 1st stage, the catalysts can significantly reduce the CO 2 -char gasification by as high as 75.00%. In the 2nd stage, the H 2 /CO ratio of ideal syngas is ~2:1 with near-0 CH 4 generation and the CH4 production can be reduced as high as 61.29% for the CO 2 –H 2 O-Char coal gasification. The activation energy for the 2nd stage is reduced by as high as 35.43% than that of raw coal without use Na–Fe catalyst. The overall carbon footprint reduction for the study is reduced by 87.33% in the 1st stage and 96.77% compared to the direct coal combustion.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Enabling The Next Generation of Smart Sensors in Coal Fired Power Plants using Cellular 5G Technology

Ohio University (OHIO), West Virginia University (WVU), and American Electric Power (AEP) proposed to study and report on the benefits of 5G wireless cellular technologies for coal-fired power plants. The significant advantages, cost savings, and potential of 5G wireless data communications based sensors promised to usher in a new era of reliable, inexpensive, and powerful embedded systems that had not previously been available for coal-fired power plants. The team built upon existing experience with cellular-based systems, power plant water quality sensing, and high temperature sensors developed during past projects. Principal Investigator Wilhelm had been developing cellular-based sensor data systems with a commercial partner for 10 years, pioneering innovative solar-powered devices that began with 2G technology. The lessons and knowledge gained served as a foundation to demonstrate innovations and potential impacts specific to coal fired power plants enabled by 5G technology, along with integration with existing sensors and systems.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Computational Analysis of the Impact of Boundary Conditions on a Particle-Laden Flow: A Case Study in a Pressurized Oxy-Coal Combustor

Designing an effective burner is vital for the development of coal combustion technologies. Because of high pressure, the volumetric fraction of the coal particles in the injected fuel in a pressurized oxy-combustion (POC) burner approaches or even exceeds the limitations allowed by the commercial computational fluid dynamics codes (e.g., Ansys Fluent). Consequently, for such high particle volumetric fractions, the interplay between the particles, the fluid flow, and the burner wall needs to be re-evaluated. The present computational work is a first step in a systematic analysis of the roles of various characteristics involved in the POC process, such as the method of particle release, its location, and the particle size. Specifically, pulverized coal is burned under an elevated pressure of 15 bar in an O 2 /CO 2 environment. A 100 kW, a POC combustor, is modeled with Ansys Fluent using the Reynolds-averaged Navier−Stokes approach. It is revealed that for this pilot-scale, pressurized burner, the gas phase flow velocity in the near-wall region exhibits anomalies. With the major focus on POC, this work aims to eliminate/reduce the impact of high particle loading on the gas-phase flow. To scrutinize the role of particle loading in the near-wall region and eliminate the impact of this velocity on POC downstream, the particle−gas interplay in the boundary layer is investigated by means of the computational simulations incorporating the coupling between the turbulent flow and the particles. It is found that the tuning of the particle release location makes the gas-phase flow velocity in the presence of particles consistent with the pure gas flow velocity profile. The particles size is also found to have a significant impact on the particle trajectory.

CFD↗

DOE OSTI2019

Micron-scale distribution controls metal(loid) release during simulated weathering of a Pennsylvanian coal shale

Abstract not provided

Singer, David M.↗

DOE OSTI2020

Power Plant Water Risk and Adaptive Measures Database

Project objective was to understand water-related constraints affecting conventional powerplant operations, specifically coal-fired power plants. Of concern were threats related to drought and flood affecting both water supply and ability of plant to discharge wastewater. Also of interest were adaptive measures taken to mitigate identified threats. This spreadsheet contains the responses provided by the power plant operators and owners. Data have been "sanitized" (e.g., random plant ID, binned location and generation capacity information) to ensure anonymity of individual power plants.

Adaptive Measures↗

DOE OSTI2022

Gas generation and intramolecular isotope study in laboratory pyrolysis of the Springfield coal from the Illinois Basin

Position-specific (PS) isotopes of propane have been proposed as a potential geochemical tool to decipher various geological processes (e.g., thermal cracking, biodegradation, H exchange) in natural reservoirs. The limited studies have been conducted on the PS isotopes of propane from the pyrolysis gases from marine shales, and natural gases sourced from lacustrine and marine kerogens, but little is known on gases produced from the humic kerogen. Here, this study investigated the PS δ 13 C of propane in the closed-system pyrolysis of the Springfield coal, Illinois Basin, Indiana, at 310 to 470 °C (Easy %Ro: 0.76 to 3.07). The C kinetic isotope effect (KIE) of CH 4 produced in both this study and previous low-temperature pyrolysis of the same coal indicates the cleavage of C—O bonds is the main generation pathway at the early kerogen cracking stage, followed by the breakdown of alkyl groups. At the wet-gas cracking stage, C 3 H 8 production from thermally stable compounds has a significant influence on the bulk and position-specific C KIE in the pyrolysis of marine Woodford kerogen and Springfield coal. According to the PS δ 13 C of propane, the central site is likely more enriched in 13 C and the δ 13 C of the terminal site is relatively heterogeneous within the propyl group attached to different functional groups of the gas-prone kerogen. Our findings based on the pyrolysis experiments and natural gas samples indicate thermal cracking and biodegradation appear to alter the δ 13 C cen values more significantly than the δ 13 C ter values of propane. The larger magnitude of ΔC c-t in the kMC simulations (Peterson et al., 2018) compared with those from the marine shale and coal possibly implies the non-random distributions of 13 C of propane precursors in the kerogens. As a new dimension of intramolecular isotopic information of propane, the PS δ 13 C values can contribute to fingerprinting the gas origins and identifying the various geological processes (e.g., kerogen cracking, wet-gas cracking, microbial activities) in sedimentary basins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Beneficial Use of Harvested Ponded Fly Ash and Landfilled FGD Materials for High-Volume Surface Mine Reclamation

The overall motivation of this project was to demonstrate at laboratory, bench-scale, and full-scale demonstration levels that (a) coal ash surface impoundments can go through closure by removal as per USEPA and state regulations so that the material can be used as is (other than draining free water using CCRs piles) in high-volume beneficial applications, (b) FGD material from closed out FGD facilities can be excavated and recompacted for coal mine reclamation, and (c) harvested CCRs can be beneficially utilized (providing a net environmental gain) in large-volumes for reclamation at abandoned coal mine sites across the US, especially in the Eastern and Midwest coal mining regions. The objectives of this project were to: 1) promote the safe and cost-effective closure by removal of coal ash impoundments, 2) harvest landfilled FGD, and 3) promote the high-volume beneficial use of these harvested CCRs in the reclamation of abandoned surface coal mine sites across the eastern and midwestern coal mining regions of the United States. The major tasks carried out for this project are summarized below: 1) Conesville Full-Scale Demonstration Project: About 2 million tons of harvested CCR materials from the closure by removal of an inactive fly ash pond and an adjacent old FGD landfill were used for the full-scale demonstration project to fully reclaim a nearby partially completed abandoned surface coal mine. Site monitoring for the project duration was carried out and results are discussed. 2) Laboratory Testing: Geotechnical and environmental testing of harvested ponded fly ash and landfilled FGD material at the former Conesville power plant were carried out. Completing the laboratory testing allowed for QA/QC for the full-scale site construction and informed the formulation of the risk analysis. 3) Risk Analysis: We developed a reliable computational model for fate and transport. We used these models and the rich set of monitored data for the Conesville site to analyze risks to human health and ecological risks associated with high-volume surface mine reclamation using harvested CCRs. 4) GIS Siting Study: A Geographic Information System (GIS) study was carried out for three states in the Eastern coal mining region and two states in the Midwest coal region. This effort provided site specific GIS information for five states and allowed us to establish protocols that other states can follow in implementing their own state specific GIS study.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2020

Slag Management of Carbon Feedstock Used in Gasification FY17 TCF between Eastman Chemical and NETL (Final Report)

NETL, in collaboration with Eastman Chemical Corp (Kingsport, TN), targeted the joint evaluation and refinement of a slag management program developed by NETL (NETL IP, patent applied for) to control gasifier slag properties formed from ash in individual or combinations of different coal-based carbon feedstock materials and specific slag modifiers used in gasification. Slag forms from mineral or organic-metallic impurities in the carbon feedstock that melt at the high temperatures of gasification, coalescing to form a liquid (slag) that must flow from the gasifier. Slag additives, also known as slag modifiers, are often added to the carbon feedstock to modify the ash chemistry and achieve desired slag flow properties at target temperatures used in gasification. If slag does not flow from a gasifier, its buildup within the gasification chamber will cause either gasifier shutdown to physically remove the slag (consuming time and damaging the protective refractory lining), or the gasification temperature must be increased to lower slag viscosity so it can flow from the gasifier, leading to greater refractory wear/corrosion, along with increased fouling and downstream component wear. Because of these issues, gasification is typically targeted at the lowest temperature possible where slag will flow in a controlled manner (a temperature range called T100 for the lowest temperature, with T250 being the highest temperature where the slag has achieved the desired fluidity). That temperature range also needs to yield a desired syngas composition, highlighting the importance of knowing and being able to control carbon feedstock slag viscosity and the temperature of thermal breakdown of the carbon feedstock. Slag viscosity varies with changes in the gasification chamber temperature, oxygen partial pressure, and slag chemistry. The slag model work with Eastman Chemical targeted predicting and controlling molten coal ash slag behavior at specific gasification conditions. The final goal of the refined model was to develop/refine the NETL slag model so a gasifier operator would be able to predict slag behavior prior to purchasing or using a carbon feedstock and control slag properties once a carbon feedstock is being gasified, allowing a gasifier user to determine what mineral additives or blends of different carbon materials would be needed to achieve desired slag properties at targeted gasification conditions. For a given carbon feedstock and desired gasification condition, the actual gasification cost and slag behavior would be able to be predicted using the slag management program in advance of purchasing or using the carbon feedstock – allowing accurate control of slag ash behavior in real time. As part of the TCF project work with Eastman Chemical, the viscosity of several ash compositions of interest to them would be measured and used to populate the slag model, along with a large database of historical slag temperature, chemistry, and viscosity information they possess – information that would in-crease the predictive accuracy of the slag management model with slag ash chemistry of interest to them. As part of the model evaluation and refinement, the predictive model and its database will be installed on computers at Eastman Chemical and used to manage slag properties in a gasifier during real-time operation of their gasifier. In summary, success of the slag management program at Eastman Chemical would support its use by other gasifier operators to manage slag chemistry and properties over other desired gasification temperature ranges, allowing greater process control and efficiency of their carbon feedstock conversion during gasification.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Enabling Entrained-Flow Gasification of Blends of Coal, Biomass and Plastics (Final Report)

This project demonstrated the technical feasibility of gasifying blends of coal, biomass and mixed waste plastics in a high pressure entrained-flow gasifier for production of hydrogen. This was achieved by creating slurries of coal, biomass pyrolysis liquids and liquefied plastic oil. Specific objectives of the project included (1) determining compositions of coal-biomass-plastic mixtures that produce a stable slurry suitable for pumping to high pressure, (2) designing and testing a novel burner to effectively atomize the mixed feedstock slurry in a pressurized gasifier, and (3) acquiring first-of-a-kind performance data for pressurized, oxygen-blown entrained-flow gasification of slurried blends of coal, biomass and plastic. A key focus of the project was preparation of mixtures of coal, biomass and plastic. To facilitate easy pumping to high pressure, slurries were created using (i) bioliquid resulting from a well-established rapid thermal treatment pyrolysis process, (ii) oil produced from waste plastic via an available thermal conversion process, and (iii) ground coal. Lab-scale tests were conducted to evaluate viscosity and stability/propensity for the mixtures to separate over time. Larger batches of the most promising slurry compositions were prepared and subjected to pumping studies. It was found that mixtures containing less than about 40% coal and less than about 30% plastic oil were stable and of low enough viscosity to facilitate pumping to high pressure. A high-performance hot oxygen burner (HOB) was designed and fabricated for use in an existing 1 ton/day pressurized entrained-flow gasifier. Ex-situ testing demonstrated that the HOB provides excellent atomization of the slurries and creates a very uniform and robust flame. Performance of the HOB in the gasifier was exceptional and resulted in better conversion to syngas than any previous generation of burner. Fabricating the HOB for this project was challenging due to the relatively small scale of the gasifier. Performance in larger-scale systems is expected to be even better. Gasification of mixtures of coal, bioliquid and plastic oil proved to be relatively easy. The gasifier was able to be started up, pressurized and transitioned to the blended slurry feedstock with no technical difficulty. Syngas rich in CO and H 2 , with relatively low concentrations of CO 2 , was produced. During startup and at low gasification temperatures, soot formation was observed, as is typical for gasification of petroleum-based feedstocks. No slag buildup was observed under the conditions tested. The project was successful in demonstrating the technical feasibility of the concept. Future development should broaden the range of feedstocks under consideration, more deeply explore performance of the gasifier, and evaluate scale-up and implementation strategies.

08 HYDROGEN↗

DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2020

Update on the United States Advanced Ultra-Supercritical Program with Full Scale Component Fabrication to Develop Utility Scale Power Plants with 760°C Steam Temperature

Following the successful completion of a 15-year effort to develop and test materials that would allow coal-fired power plants to be operated at advanced ultra-supercritical (A-USC) steam conditions, a United States-based consortium is presently engaged in Phase 2 of a project which includes an advanced manufacturing effort to complete US-based supply chain development for full commercial scale (800-850 MWe) A-USC components made of nickel-based alloys, components operating at up to 760°C. The project, funded under U.S. Department of Energy Award No. DE-FE0025064, falls under the US DOE overall goal to Develop cost-effective, reliable technologies to improve the efficiency of new and existing coal-fired power plants. A-USC steam cycles have the potential to improve cycle efficiency, reduce fuel costs, and reduce greenhouse gas emissions. Current development and demonstration efforts are focused on enabling the construction of A-USC plants, operating with steam temperatures as high as 1400°F (760°C) and steam pressures up to 5000 psi (35 MPa), which can potentially increase cycle efficiencies to 47% HHV (higher heating value), or approximately 50% LHV (lower heating value), and reduce CO 2 emissions by roughly 25%, compared to today’s U.S. fleet. A-USC technology provides a lower-cost method to reduce CO 2 emissions, compared to CO 2 capture technologies, while retaining a viable coal option for owners of coal generation assets. Among the specific goals of Phase 2 of the ComTest Project are to: validate that components made from advanced nickel-based alloys can operate and perform under A-USC conditions accelerate the development of a U.S.-based supply chain for the full complement of A-USC components close the remaining gaps and reduce the risks for manufacturing components from advanced materials for commercial demonstration fabricate full-scale versions of selected key components made of nickel-based alloys validate a qualified U.S. supply chain, to provide greater cost certainty for components obtain American Society of Mechanical Engineers (ASME) code approval for new materials, components and processes Additional benefit: Manufacturing technology will be applicable to other advanced fossil energy high temperature cycles, and can support increased flexibility of existing power plants The ComTest project is managed by Energy Industries of Ohio, and technically directed by the Electric Power Research Institute, Inc., with General Electric designing the A-USC components. As stated earlier, the current phase of the effort is primarily funded by the U.S. Department of Energy, through the National Energy Technology Laboratory. This presentation outlines the motivation for the project, explains the project’s structure and schedule, and provides some of the technical details on the design of the ComTest components.

01 COAL, LIGNITE, AND PEAT↗