Search NASA⌕ Search

SEARCH · Search NASA

Results for “Coating processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Directional Crystallization of Conjugated Molecules during Coating Processes

The coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and coating parameters, we identified that it is crucial for the coating speed to match the growth speed of the fastest growing crystal plane to achieve a high degree of directional crystallization.

36 MATERIALS SCIENCE↗
NASA NTRS2018

Effect of Pre- and Post-Coat Processing on the Fatigue Life of Coated Disk Alloys

Increasing temperatures in aero gas turbines is resulting in oxidation and hot corrosion attack of turbine disks. Since disks are sensitive to low cycle fatigue (LCF), any environmental attack, and especially hot corrosion pitting, can seriously degrade the life of the disk. Application of metallic coatings is one means of protecting disk alloys from this environmental attack. However, since LCF is sensitive to surface conditions, pre- and post-coat processing can have a significant effect on the LCF life of coated bars. Various pre-and post-coating conditions were examined with a Ni-45wt. Cr coating applied by High-power impulse magnetron sputtering (HiPiMS) to a Ni-based disk alloy. Initial pre-coat surface conditions examined a grit blasted surface. Later pre-coat surface treatments involved wet blasting, two shot peening levels (8N-200 and 16N-200) and a highly polished surface. Post-coat treatments involved two shot peening levels (4N-100 and 16N-200) and a post-coat diffusion anneal in high purity Ar or a low PO2 environment to encourage chromia scale formation. Half of the coated and uncoated bars were LCF tested at 760C without further environmental exposure to evaluate the pre- and post-coat treatments. The second half of samples were either oxidized for 500 hours at 760C in air, hot corroded for 50 hours at 760C in air using a Na2SO4-MgSO4 salt, or subjected to both exposures. Results of the LCF testing and post-test characterization of the various coatings will be presented and future research directions discussed.

LCF Life↗
DOE OSTI2021

SiOC coatings on yttria stabilized zirconia microspheres using a fluidized bed coating process

In this study, defect-free SiOC coatings were prepared on yttria stabilized zirconia (YSZ) microspheres by a fluidized bed coating process. Effects of the rheological properties of the coating solution on the coating process were elucidated. An impact regime diagram was constructed, which demonstrated that the coating mechanisms were collision/impact. During the fluidized bed coating, longer spouted time resulted in wider dispersion, longer residence time, and more circulatory motion of particles; the fluid distributed more uniformly throughout the column, as demonstrated in our Multiphase Flow with Interface eXchange (MFiX) simulations. Two-step pyrolysis in Ar achieved complete coating layers, which were comprised of SiOC, SiO 2 , SiC, and graphite. The two stage mass loss during the pyrolysis corresponded to simultaneous reactions due to depolymerization and hydrocarbon loss from 400 to 600°C. Carbon cluster size in the pyrolyzed samples was calculated to be 25 ± 2 Å. In conclusion, this work provides a new method for producing SiOC coatings on micron spheres, with nuclear TRISO fuel particles as the application.

42 ENGINEERING↗
NASA NTRS1976

A parylene coating process for hybrid circuits

The parylene coating process developed during this program consists of (1) obtaining a hybrid cover with a hole in it, (2) sealing of the circuit with a hole in the cover, (3) parylene coating through the hole with the external leads protected from parylene by appropriate fixturing, and (4) sealing of the hole by soldering a pretinned kovar tab. Development of the above process required optimization of the parylene coater parameters to obtain a uniform consistent coating which could offer adequate protection to the circuits, fixture design for packages of various types, determination of the size of the deposition hole, and the amount of dimer charge per run, a process to hermetically seal the deposition holes and establishment of quality control techniques or acceptance criteria for the deposited film.

Source record↗
NASA NTRS1977

A production parylene coating process for hybrid microcircuits

The real impetus for developing a production parylene coating process for internal hybrid passivation came as a result of the possibility of loose conductive particles in hybrid microelectronic circuits, causing intermittent and sometimes permanent failures. Because of the excellent mechanical properties of parylene, it is capable of securing the loose particles in place and prevent such failures. The process of coating described consists of (1) vaporizing the initial charge, which is in the form of a dimer; (2) conversion of the dimer into a reactive monomer; and (3) deposition and subsequent polymerization of the monomer in the deposition chamber which forms a uniform parylene film over all the cold surfaces in contact. Experimental results are discussed in terms of wire bond reliability, resistor drift, high-temperature storage characteristics of parylene, and coating acceptance standards. It is concluded that internal cavities of microelectronic circuits can be successfully coated with parylene provided appropriate tooling is used to protect external leads from the parylene monomer.

Kale, V. S.↗
DOE OSTI2023

A Versatile Fiber Coating Process for Efficient Fabrication of Multifunctional Composites

The objective of this research is to demonstrate the versatility of a dip coating process for the efficient integration of piezoelectric barium titanate (BaTiO3) microparticles on a wide variety of fibers to design passive self-sensing composites. The microparticles were deposited on glass, aramid, and basalt fiber weaves through the proposed dip coating technique. A computational framework is established to predict the deposition thickness on the fiber surfaces from the given microparticle concentration, size, coating velocity, and coating fluid viscosity. The deposition quality assessment was performed through scanning electron microscope imaging and subsequent image analysis. BaTiO3-coated fibers were directly used in composite preparation. After fabrication, the BaTiO3-enhanced composites were subjected to high-voltage poling. Finally, their passive self-sensing properties were characterized through experimental studies. The results show the adaptability of the proposed coating process to integrate BaTiO3 microparticles within different types of fiber-reinforced composites enabling passive self-sensing to attain subsurface damage characterization.

Gupta, Sumit↗
DOE OSTI2021

Solvent absorption rate of perfluorosulphonic acid membranes towards understanding direct coating processes

Here we present a method for measurement of the rate of solvent absorption by perfluorosulfonic acid (PFSA) membranes using a force tensiometer. The method presented here can be used as a tool to understand solvent absorption and should provide a rationale for designing catalyst inks for direct coating processes since it is necessary to understand how the absorption rate – on a time scale of seconds to minutes – compares to the time scales of the coating process in order to minimize membrane swelling. This method allows for rapid screening of the absorption and swelling behavior of different solvents and mixtures. Using this method, the absorption of water/1-propanol mixtures were measured for three thicknesses of Nafion PFSA membrane – Nafion 1135, Nafion 115, and Nafion 117. We find that the absorption rate is dependent on the ratio of the solvents as well as the thickness of the membrane. The analysis indicates that the highest absorption rate occurs when the mass percentage of 1-propanol in the mixture is 50%, whereas the lowest rates are for pure water and 1-propanol. In addition, membrane distortion also occurs most quickly for the 50% 1-propanol mixture. Our results suggest that catalyst inks that are highly rich (=90%) in water or 1-propanol are likely best for direct coating as such formulations will minimize absorption and swelling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1998

Evaluation of Chemical Coating Processes for AXAF

The need existed at MSFC for the development and fabrication of radioisotope calibration sources of cadmium 109 and iron 55 isotopes. This was in urgent response to the AXA-F program. Several issues persisted in creating manufacturing difficulties for the supplier. In order to meet the MSFC requirements very stringent control needed to be maintained for the coating quality, specific activity and thickness. Due to the difficulties in providing the precisely controlled devices for testing, the delivery of the sources was seriously delayed. It became imperative that these fabrication issues be resolved to avoid further delays in this AXA-F observatory key component. The objectives are: 1) Research and provide expert advice on coating materials and procedures. 2) Research and recommend solutions to problems that have been experienced with the coating process. 3) Provide recommendations on the selection and preparation of substrates. 4) Provide consultation on the actual coating process including the results of the qualification and acceptance test programs. 5) Perform independent tests at UAH or MSFC as necessary.

Engelhaupt, Darell↗
NASA NTRS1983

Coating Process

A black chrome coating, originally developed for spacecraft solar cells, led to the development of an efficient flat plate solar collector. The coating, called Chromonyx, helps the collector absorb more heat. Olympic Solar Corporation was formed to electroplate the collector. The coating technique allows 95% of the sun's energy to be utilized. The process is widely used.

Source record↗
DOE OSTI2020

An Experimental Investigation of Multilayer Flow in a Slide Die Coating Process

Roll-to-roll coating technology has been actively applied not only for conventional film production but also for emerging energy devices such as organic solar cells, organic light emitting diodes, batteries, smart windows, and fuel cells. The devices are multilayer structures requiring several coating and drying steps when implemented in a serial fashion, which increases capital costs and energy consumption. Simultaneous multilayer (ML) coating technologies present an opportunity for cost reductions and improved process efficiency by reducing equipment footprint and the number of process steps. In this talk, we experimentally investigate ML slide die coating flow for the manufacturing of fuel cell membrane electrode assemblies (MEAs). For ML slide coating, understanding fluid properties such as density, surface tension, and viscosity are necessary for stable flows and limiting intermixing of the miscible layers. Here, we utilize a design-of-experiment methodology - Box-Behnken design (BBD) - to correlate ink formulation parameters to fluid properties. Using the ink properties obtained from the BBD, we performed numerical flow simulations to obtain a proper process conditions to guide experimental coating trials. Finally, experimental verification is performed on a ML slide die and a degree of miscibility was observed for various ink formulation conditions.

28 EE - Advanced Manufacturing Office (EE-5A)↗
NASA NTRS1992

Anodized aluminum coatings for thermal control. I - Coating process and stresses

Anodized aluminum is a candidate material for use as a thermal radiator surface on Space Station Freedom. Here, results of measurements of coating stress at room temperature are presented. The effects of coating process conditions and also subsequent exposure to different humidities, from above ambient to vacuum, are reported. The most important observation with regard to space applications is that the coating stress is very dependent on humidity, changing from compressive at ambient humidity to strongly tensile in 10 exp -6 torr vacuum. The increase in stress is accompanied by loss of water from the coating, and the process is reversible.

Alwitt, R. S.↗
DOE OSTI2026

Inconel 718 Oxide Coating Process for Mu2e Target Redesign

A method of growing an oxide coating on Inconel 718 samples was investigated to increase the emissivity of the redesigned Inconel Mu2e production target. Microscopy and emissivity measurements of a range of samples indicate excellent performance.

Williams, J. [Fermilab]↗
NASA NTRS1989

Lubricant Coating Process

"Peen Plating," a NASA developed process for applying molybdenum disulfide, is the key element of Techniblast Co.'s SURFGUARD process for applying high strength solid lubricants. The process requires two machines -- one for cleaning and one for coating. The cleaning step allows the coating to be bonded directly to the substrate to provide a better "anchor." The coating machine applies a half a micron thick coating. Then, a blast gun, using various pressures to vary peening intensities for different applications, fires high velocity "media" -- peening hammers -- ranging from plastic pellets to steel shot. Techniblast was assisted by Rural Enterprises, Inc. Coating service can be performed at either Techniblast's or a customer's facility.

Source record↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

The technical and economic feasibility of producing solar cell quality sheet silicon by dip-coating one surface of carbonized ceramic substrates with a thin layer of large grain polycrystalline silicon was investigated. The dip-coating methods studied were directed toward a minimum cost process with the ultimate objective of producing solar cells with a conversion efficiency of 10% or greater. The technique shows excellent promise for low cost, labor-saving, scale-up potentialities and would provide an end product of sheet silicon with a rigid and strong supportive backing. An experimental dip-coating facility was designed and constructed, several substrates were successfully dip-coated with areas as large as 25 sq cm and thicknesses of 12 micron to 250 micron. There appears to be no serious limitation on the area of a substrate that could be coated. Of the various substrate materials dip-coated, mullite appears to best satisfy the requirement of the program. An inexpensive process was developed for producing mullite in the desired geometry.

Heaps, J. D.↗
NASA NTRS1976

Dip coating process: Silicon sheet growth development for the large-area silicon sheet task of the low-cost silicon solar array project

To date, an experimental dip-coating facility was constructed. Using this facility, relatively thin (1 mm) mullite and alumina substrates were successfully dip-coated with 2.5 - 3.0 ohm-cm, p-type silicon with areas of approximately 20 sq cm. The thickness and grain size of these coatings are influenced by the temperature of the melt and the rate at which the substrate is pulled from the melt. One mullite substrate had dendrite-like crystallites of the order of 1 mm wide and 1 to 2 cm long. Their axes were aligned along the direction of pulling. A large variety of substrate materials were purchased or developed enabling the program to commence a substrate definition evaluation. Due to the insulating nature of the substrate, the bottom layer of the p-n junction may have to be made via the top surface. The feasibility of accomplishing this was demonstrated using single crystal wafers.

Heaps, J. D.↗