Results for “Cold spray process”

NASA NTRS2007

Development of Oxidation Resistant Coatings on GRCop-84 Substrates by Cold Spray Process

GRCop-84, a Cu-CR-Nb alloy, has been developed for rocket engine liner applications. For maximum life additional oxidation protection is required to prevent blanching. NiCrAlY was identified as a suitable coating, and efforts were initiated to develop suitable coating techniques. Cold spray is one technique under consideration. Efforts at ASB Industries to produce dense, adherent coatings are detailed. The work culminated in the production of samples for testing at NASA Glenn Research Center.

Karthikeyan, J.↗

NASA NTRS2013

Advanced Materials and Manufacturing for Low-Cost, High-Performance Liquid Rocket Combustion Chambers

A document describes the low-cost manufacturing of C103 niobium alloy combustion chambers, and the use of a high-temperature, oxidation-resistant coating that is superior to the standard silicide coating. The manufacturing process involved low-temperature spray deposition of C103 on removable plastic mandrels produced by rapid prototyping. Thin, vapor-deposited platinum-indium coatings were shown to substantially improve oxidation resistance relative to the standard silicide coating. Development of different low-cost plastic thrust chamber mandrel materials and prototyping processes (selective laser sintering and stereolithography) yielded mandrels with good dimensional accuracy (within a couple of mils) for this stage of development. The feasibility of using the kinetic metallization cold-spray process for fabrication of free-standing C1O3 thrusters on removable plastic mandrels was also demonstrated. The ambient and elevated temperature mechanical properties of the material were shown to be reasonably good relative to conventionally processed C103, but the greatest potential benefit is that coldsprayed chambers require minimal post-process machining, resulting in substantially lower machining and material costs. The platinum-iridium coating was shown to provide greatly increased oxidation resistance over the silicide when evaluated through oxyacetylene torch testing to as high as 300 F (= 150 C). The iridium component minimizes reaction with the niobium alloy chamber at high temperatures, and provides the high-temperature oxidation resistance needed at the throat.

Williams, Brian E.↗

NASA NTRS2009

Young's Moduli of Cold and Vacuum Plasma Sprayed Metallic Coatings

Monolithic metallic copper alloy and NiCrAlY coatings were fabricated by either the cold spray (CS) or the vacuum plasma spray (VPS) deposition processes. Dynamic elastic modulus property measurements were conducted on these monolithic coating specimens between 300 K and 1273 K using the impulse excitation technique. The Young's moduli decreased almost linearly with increasing temperature at all temperatures except in the case of the CS Cu-23%Cr-5%Al and VPS NiCrAlY, where deviations from linearity were observed above a critical temperature. It was observed that the Young's moduli for VPS Cu-8%Cr were larger than literature data compiled for Cu. The addition of 1%Al to Cu- 8%Cr significantly increased its Young's modulus by 12 to 17% presumably due to a solid solution effect. Comparisons of the Young s moduli data between two different measurements on the same CS Cu- 23%Cr-5%Al specimen revealed that the values measured in the first run were about 10% higher than those in the second run. It is suggested that this observation is due to annealing of the initial cold work microstructure resulting form the cold spray deposition process.

Raj, S. V.↗

NASA NTRSDate not supplied

Metal Additive Manufacturing Process Selection and Development for Propulsion Components

Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication processes. Each of these manufacturing process has unique advantages and challenges for use in aerospace propulsion applications. The most commonly used AM processes include Powder Bed Fusion (PBF), Directed Energy Deposition (DED), and solid-state processes as in Cold Spray, Ultrasonic Additive Manufacturing, and Additive Friction Stir Deposition. While detailed research has been conducted among many of the AM processes to mature processing parameters and material properties, navigating which processes are best to select is difficult as it is based on specific component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various key attributes. These key attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hot-fire evaluations, and (4) certification approaches. This presentation summarizes these results and is meant to introduce specific examples which show what to consider when designing a metal AM component for aerospace propulsion applications.

Additive Manufacturing↗

NASA NTRSDate not supplied

Metal Additive Manufacturing Process Selection and Development Lifecycle for Propulsion Components

Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication processes. Each of these manufacturing process has unique advantages and challenges for use in aerospace propulsion applications. The most commonly used AM processes include Powder Bed Fusion (PBF), Directed Energy Deposition (DED), and solid-state processes as in Cold Spray, Ultrasonic Additive Manufacturing, and Additive Friction Stir Deposition. While detailed research has been conducted among many of the AM processes to mature processing parameters and material properties, navigating which processes are best to select is difficult as it is based on specific component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various key attributes. These key attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hot-fire evaluations, and (4) certification approaches. This presentation summarizes these results and is meant to introduce specific examples which show what to consider when designing a metal AM component for aerospace propulsion applications.

Paul Gradl↗

NASA NTRS2017

Thermophysical Properties of Cold and Vacuum Plasma Sprayed Cu-Cr-X Alloys, NiAl and NiCrAlY Coatings: Electrical and Thermal Conductivity, Thermal Diffusivity, and Total Hemispherical Emissivity - Part 1

This two-part paper reports the thermophysical properties of several cold and vacuum plasma sprayed monolithic Cu and Ni-based alloy coatings. Part I presents the electrical and thermal conductivity, thermal diffusivity, and total hemispherical emissivity data while Part II reports the specific heat capacity data for these coatings. Metallic copper alloys, stoichiometric NiAl and NiCrAlY coatings were fabricated by either the cold sprayed or the vacuum plasma spray deposition processes for thermal property measurements between 77 and 1223 K. The temperature dependencies of the thermal conductivities, thermal diffusivities, electrical conductivities and total hemispherical emissivities of these cold and vacuum sprayed monolithic coatings are reported in this paper. The electrical and thermal conductivity data correlate reasonably well for Cu-8%Cr-1%Al, Cu-23%Cr-5%Al and NiAl in accordance with the Wiedemann-Franz (WF) law although a better fit is obtained using the Smith-Palmer relationship. The Lorentz numbers determined from the WF law are close to the theoretical value.

Raj, S. V.↗

NASA NTRS2002

Thin Film CuInS2 Prepared by Spray Pyrolysis with Single-Source Precursors

Both horizontal hot-wall and vertical cold-wall atmospheric chemical spray pyrolysis processes deposited near single-phase stoichiometric CuInS2 thin films. Single-source precursors developed for ternary chalcopyrite materials were used for this study, and a new liquid phase single-source precursor was tested with a vertical cold-wall reactor. The depositions were carried out under an argon atmosphere, and the substrate temperature was kept at 400 C. Columnar grain structure was obtained with vapor deposition, and the granular structure was obtained with (liquid) droplet deposition. Conductive films were deposited with planar electrical resistivities ranging from 1 to 30 Omega x cm.

Jin, Michael H.↗

NASA NTRS2006

Cold Flow Testing for Liquid Propellant Rocket Injector Scaling and Throttling

Scaling and throttling of combustion devices are important capabilities to demonstrate in development of liquid rocket engines for NASA's Space Exploration Mission. Scaling provides the ability to design new injectors and injection elements with predictable performance on the basis of test experience with existing injectors and elements, and could be a key aspect of future development programs. Throttling is the reduction of thrust with fixed designs and is a critical requirement in lunar and other planetary landing missions. A task in the Constellation University Institutes Program (CUIP) has been designed to evaluate spray characteristics when liquid propellant rocket engine injectors are scaled and throttled. The specific objectives of the present study are to characterize injection and primary atomization using cold flow simulations of the reacting sprays. These simulations can provide relevant information because the injection and primary atomization are believed to be the spray processes least affected by the propellant reaction. Cold flow studies also provide acceptable test conditions for a university environment. Three geometric scales - 1/4- scale, 1/2-scale, and full-scale - of two different injector element types - swirl coaxial and shear coaxial - will be designed, fabricated, and tested. A literature review is currently being conducted to revisit and compile the previous scaling documentation. Because it is simple to perform, throttling will also be examined in the present work by measuring primary atomization characteristics as the mass flow rate and pressure drop of the six injector element concepts are reduced, with corresponding changes in chamber backpressure. Simulants will include water and gaseous nitrogen, and an optically accessible chamber will be used for visual and laser-based diagnostics. The chamber will include curtain flow capability to repress recirculation, and additional gas injection to provide independent control of the backpressure. This paper provides a short review of the appropriate literature, as well as descriptions of plans for experimental hardware, test chamber instrumentation, diagnostics, and testing.

Kenny, Jeremy R.↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRSDate not supplied

Advancing GRCop-based Bimetallic Additive Manufacturing to Optimize Component Design and Applications for Liquid Rocket Engines

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. The ability to rapidly design and manufacture components has provided significant opportunities for development and flight programs across the propulsion industry. AM has demonstrated significant advantages that include cost and schedule savings in addition to performance improvements through new design opportunities. While these performance advantages can be in the characteristics of complex design features, they can also be in the form of new materials. AM has been demonstrated in these various component applications using a variety of metal alloys, many of which are traditional alloys for extreme environments. Additional developments were completed using AM to provide new alloys and maturing these material uses for high performance applications. Almost all of the prior developments across component applications have focused on single-alloys in these AM processes. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-alloy AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. This is particularly important in liquid rocket engine combustion devices that must reject heat in high heat flux environments yet maintain adequate structural margins under high operational pressure. NASA has been exploring several AM processes, materials, and applications for combustion devices, specifically combustion chambers, injectors, nozzles, and ignition systems. These components require fine geometric features for internal flow or cooling functionality. They experience high thermal gradients across thin-walls and must survive high pressures and temperatures from propellants and the combustion process. A copper-based alloy is normally used to provide high thermal conductivity, but at the detriment of increased weight if used as a single alloy in an AM chamber. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include copper-based material primarily and superalloys, Inconel 625 or NASA HR-1. The various aspects of the additive manufacturing processes and challenges, materials characterization, and the testing of bimetallic components in a relevant environment will be discussed.

Additive Manufacturing↗

NASA NTRS1992

Three-dimensional modeling of diesel engine intake flow, combustion and emissions

A three-dimensional computer code (KIVA) is being modified to include state-of-the-art submodels for diesel engine flow and combustion: spray atomization, drop breakup/coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, soot and radiation, and the intake flow process. Improved and/or new submodels which were completed are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NOx, and spray/wall impingement with rebounding and sliding drops. Results to date show that adding the effects of unsteadiness and compressibility improves the accuracy of heat transfer predictions; spray drop rebound can occur from walls at low impingement velocities (e.g., in cold-starting); larger spray drops are formed at the nozzle due to the influence of vaporization on the atomization process; a laminar-and-turbulent characteristic time combustion model has the flexibility to match measured engine combustion data over a wide range of operating conditions; and finally, the characteristic time combustion model can also be extended to allow predictions of ignition. The accuracy of the predictions is being assessed by comparisons with available measurements. Additional supporting experiments are also described briefly. To date, comparisons with measured engine cylinder pressure and heat flux data were made for homogeneous charge, spark-ignited and compression-ignited engines. The model results are in good agreement with the experiments.

Reitz, R. D.↗

NASA NTRS2005

Characterization of Cold Sprayed CuCrAl Coated GRCop-84 Substrates for Reusable Launch Vehicles

An advanced Cu-8(at.%)Cr-4%Nb alloy developed at NASA's Glenn Research Center, and designated as GRCop-84, is currently being considered for use as combustor liners and nozzles in NASA's future generations of reusable launch vehicles (RLVs). Despite the fact that this alloy has superior mechanical and oxidation properties compared to many commercially available copper alloys, it is felt that its high temperature and environmental resistance capabilities can be further enhanced with the development and use of suitable coatings. Several coatings and processes are currently being evaluated for their suitability and future down selection. A newly developed CuCrAl has shown excellent oxidation resistance compared to current generation Cu-Cr coating alloys. Cold spray technology for depositing the CuCrAl coating on a GRCop-84 substrate is currently being developed under NASA's Next Generation Launch Technology (NGLT) Propulsion Research and Technology (PR&T) project. The microstructures, mechanical and thermophysical properties of overlay coated GRCop-84 substrates are discussed.

Raj, S . V.↗

NASA NTRSDate not supplied

Optimization of Rocket Engine Components using Multi-Metallic Additive Manufacturing

Additive manufacturing (AM) is advancing many applications of component design for liquid rocket engines. AM has been demonstrated in various rocket component applications using a variety of monolithic metal alloys, many of which are traditional alloys for extreme environments. NASA and industry partners have focused in recent years to advance processing to create bimetallic and multicomponent AM processes and materials. The role of multi-metallic AM offers advantages since it can further optimize weight, optimize reliability and performance by increasing the strength to weight ratio of a component, and can optimize materials for various engineering requirements. NASA’s Rapid Analysis and Manufacturing Propulsion Technology (RAMPT) project has designed and manufactured a series of additively manufactured (AM) coupled combustion chambers, nozzles, and other engine components to advance new AM processes and materials with the goal of reducing cost and schedule for engine manufacturing. These designs incorporated multimetallic AM, which further enabled carbon-fiber composite overwrap to reduce overall thrust chamber assembly (TCA) mass. Various AM processes were demonstrated on these components using a copper-based alloy/superalloy bimetallic solution. The AM processes being explored individually and in combination for bimetallic applications include Laser Powder Bed Fusion (L-PBF), Laser Powder Directed Energy Deposition (LP-DED), and cold spray. The combination of bimetallic material combinations explored in this research include GRCop-based alloys and superalloys, Inconel 625 or NASA HR-1. One unique development that will be presented is the combustion chamber and nozzle as a single component by using freeform integrated DED to build the nozzle directly onto the aft end of the chamber. The various aspects of the additive manufacturing processes and challenges, materials characterization and mechanical testing, and hot-fire testing of bimetallic components in a relevant rocket engine environment will be discussed.

Additive Manufacturing↗

NASA NTRS2024

Aerosol Size Distribution Properties Associated With Cold-Air Outbreaks in the Norwegian Arctic

The aerosol particles serving as cloud condensation and ice nuclei contribute to key cloud processes associated with cold-air outbreak (CAO) events but are poorly constrained in climate models due to sparse observations. Here we retrieve aerosol number size distribution modes from measurements at Andenes, Norway, during the Cold-Air Outbreaks in the Marine Boundary Layer Experiment (COMBLE) and at Zeppelin Observatory, approximately 1000 km upwind from Andenes at Svalbard. During CAO events at Andenes, the sea-spray-mode number concentration is correlated with strong over-ocean winds with a mean of 8±4 cm−3 that is 71 % higher than during non-CAO conditions. Additionally, during CAO events at Andenes, the mean Hoppel minimum diameter is 6 nm smaller than during non-CAO conditions, though the estimated supersaturation is lower, and the mean number concentration of particles that likely activated in-cloud is 109±61 cm−3 with no statistically significant difference from the non-CAO mean of 99±66 cm−3. For CAO trajectories between Zeppelin Observatory and Andenes, the upwind-to-downwind change in number concentration is the largest for the accumulation mode with a mean decrease of 93±95 cm−3, likely attributable primarily to precipitation scavenging. These characteristic properties of aerosol number size distributions during CAO events provide guidance for evaluating CAO aerosol–cloud interaction processes in models.

accumulation mode particle scavenging↗

NASA NTRS2015

Fundamental Study of a Single Point Lean Direct Injector. Part I: Effect of Air Swirler Angle and Injector Tip Location on Spray Characteristics

Lean direct injection (LDI) is a combustion concept to reduce oxides of nitrogen (NOx) for next generation aircraft gas turbine engines. These newer engines have cycles that increase fuel efficiency through increased operating pressures, which increase combustor inlet temperatures. NOx formation rates increase with higher temperatures; the LDI strategy avoids high temperature by staying fuel lean and away from stoichiometric burning. Thus, LDI relies on rapid and uniform fuel/air mixing. To understand this mixing process, a series of fundamental experiments are underway in the Combustion and Dynamics Facility at NASA Glenn Research Center. This first set of experiments examines cold flow (non-combusting) mixing using air and water. Using laser diagnostics, the effects of air swirler angle and injector tip location on the spray distribution, recirculation zone, and droplet size distribution are examined. Of the three swirler angles examined, 60 degrees is determined to have the most even spray distribution. The injector tip location primarily shifts the flow without changing the structure, unless the flow includes a recirculation zone. When a recirculation zone is present, minimum axial velocity decreases as the injector tip moves downstream towards the venturi exit; also the droplets become more uniform in size and angular distribution.

vortex↗

NASA NTRS2014

Fundamental Study of a Single Point Lean Direct Injector. Part I: Effect of Air Swirler Angle and Injector Tip Location on Spray Characteristics

Lean direct injection (LDI) is a combustion concept to reduce oxides of nitrogen (NOx) for next generation aircraft gas turbine engines. These newer engines have cycles that increase fuel efficiency through increased operating pressures, which increase combustor inlet temperatures. NOx formation rates increase with higher temperatures; the LDI strategy avoids high temperature by staying fuel lean and away from stoichiometric burning. Thus, LDI relies on rapid and uniform fuel/air mixing. To understand this mixing process, a series of fundamental experiments are underway in the Combustion and Dynamics Facility at NASA Glenn Research Center. This first set of experiments examines cold flow (non-combusting) mixing using air and water. Using laser diagnostics, the effects of air swirler angle and injector tip location on the spray distribution, recirculation zone, and droplet size distribution are examined. Of the three swirler angles examined, 60 deg is determined to have the most even spray distribution. The injector tip location primarily shifts the flow without changing the structure, unless the flow includes a recirculation zone. When a recirculation zone is present, minimum axial velocity decreases as the injector tip moves downstream towards the venturi exit; also the droplets become more uniform in size and angular distribution.

Tedder, Sarah A.↗

NASA NTRSDate not supplied

Robust Metal Additive Manufacturing Process Selection and Development for Aerospace Components

Metal additive manufacturing (AM) is a generic term that captures a variety of fabrication techniques. Each of these manufacturing process has unique advantages, applications for use, and challenges. The most common AM processes in use include Powder Bed Fusion (PBF) and Directed Energy Deposition (DED) as well as many solid state processes. While detailed research has been conducted among many of the processes including parameters and material properties, navigating which processes are best to select is difficult as it is based on component requirements. The focus of this presentation is to provide an overview of considerations for each of metal AM process selection for aerospace components based on various attributes. These attributes include geometric considerations, metallurgical characteristics, cost basis, post-processing and maturity of the processes. The data for these trade selections are based on studies that NASA as performed internally and with academic and industry partners. These studies include multiple AM build experiments to evaluate (1) geometric variations and constraints within the processes, (2) alloy characterization and mechanical testing, (3) pathfinder component development and hotfire evaluations, and (4) certification approaches. This presentation summarizes these results and meant to introduce various considerations when designing a metal AM component.

Additive Manufacturing↗

NASA NTRS2011

Gas Dynamic Spray Technology Demonstration Project Management

The standard practice for protecting metallic substrates in atmospheric environments is the use of an applied coating system. Current coating systems used across AFSPC and NASA contain volatile organic compounds (VOCs) and hazardous air pollutants (HAPs). These coatings are sUbject to environmental regulations at the Federal and State levels that limit their usage. In addition, these coatings often cannot withstand the high temperatures and exhaust that may be experienced by Air Force Space Command (AFSPC) and NASA structures. In response to these concerns, AFSPC and NASA have approved the use of thermal spray coatings (TSCs). Thermal spray coatings are extremely durable and environmentally friendly coating alternatives, but utilize large cumbersome equipment for application that make the coatings difficult and time consuming to repair. Other concerns include difficulties coating complex geometries and the cost of equipment, training, and materials. Gas Dynamic Spray (GOS) technology (also known as Cold Spray) was evaluated as a smaller, more maneuverable repair method as well as for areas where thermal spray techniques are not as effective. The technology can result in reduced maintenance and thus reduced hazardous materials/wastes associated with current processes. Thermal spray and GOS coatings also have no VOCs and are environmentally preferable coatings. The primary objective of this effort was to demonstrate GDS technology as a repair method for TSCs. The aim was that successful completion of this project would result in approval of GDS technology as a repair method for TSCs at AFSPC and NASA installations to improve corrosion protection at critical systems, facilitate easier maintenance activity, extend maintenance cycles, eliminate flight hardware contamination, and reduce the amount of hazardous waste generated.

Lewis, Pattie↗