Search NASA⌕ Search

SEARCH · Search NASA

Results for “Collab”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The EGS Collab Project – Stimulations at Two Depths

The EGS Collab project, supported by the US Department of Energy, is performing intensively monitored rock stimulation and flow tests at the 10-m scale in an underground research laboratory to address challenges in implementing enhanced geothermal systems (EGS). Data and observations from the field tests are compared to simulations to understand processes and build confidence in numerical modeling of the processes. We have completed Experiment 1 (of 3), which examined hydraulic fracturing in a well-characterized underground fractured phyllite test bed at a depth of approximately 1.5 km at the Sanford Underground Research Facility (SURF) in Lead, South Dakota. Testbed characterization included fracture mapping, borehole acoustic and optical televiewers, full waveform sonic, conductivity, resistivity, temperature, campaign p- and s-wave investigations and electrical resistance tomography. Borehole geophysical techniques including passive seismic, continuous active source seismic monitoring, electrical resistance tomography, fiber-based distributed strain, distributed temperature, and distributed acoustic monitoring, were used to carefully monitor stimulation events and flow tests. More than a dozen stimulations and nearly one year of flow tests were performed. Quality data and detailed observations were collected and analyzed during stimulation and water flow tests using ambient temperature and chilled water. We achieved adaptive control of the tests using real-time monitoring and rapid dissemination of data and near-real-time simulation. More detailed numerical simulation was performed to answer key experimental design questions, forecast fracture propagation trajectories and extents, and analyze and evaluate results. Data are freely available from the Geothermal Data Repository. Experiment 2 examines the potential for hydraulic shearing in amphibolite at a depth of about 1.25 km at SURF. This site has a different set of stress and fracture conditions than Experiment 1. The Experiment 2 testbed consists of nine subhorizontal boreholes configured in two fans of two boreholes which surround the testbed and contain grouted-in electrical resistance tomography, seismic sensors, active seismic sources and distributed fiber sensors. A “five-spot” set of test wells that extends from a custom mined alcove includes an injection well and four production/monitoring wells. The testbed was characterized geophysically and hydrologically, and three stimulations have been performed using the Step-Rate Injection Method for Fracture In-Situ Properties (SIMFIP) tool to measure strains, and a new strain quantifying tool (downhole robotic strain analysis tool -DORSA) was deployed in a monitoring hole during stimulation. Real-time data were broadcast during stimulations to allow real-time response to arising issues.

EGS Collab, Enhanced Geothermal Systems, EGS, fiel↗
DOE OSTI2021

Modeling heat transport processes in enhanced geothermal systems: Validation study from EGS Collab Experiment 1

Heat recovery from enhanced geothermal systems (EGS) is a complex process involving heat transport in both fracture networks and rock formations. A comprehensive understanding of and the ability to model the underlying heat transport mechanisms is important for the success of EGS but remains challenging in practice due to the generally insufficient characterization of EGS reservoirs. In the present study, we analyze an extensively monitored intermediate-scale EGS field experiment performed in a well-characterized testbed. The high-resolution, high-quality measurements from the field experiment enable the development of a high-fidelity model incorporating a well-constrained fracture network. Based on the field experiment, we investigate the complex heat transport processes in an EGS-relevant environment and validate the capability of a numerical approach in simulating these inherently coupled heat transport processes. A series of numerical simulations were performed to study the effects of different heat transport mechanisms, including thermal convection with fracture flow, thermal conduction in rock formations, and the Joule-Thomson effect. The agreement of thermal responses between field measurements and simulation results indicates that our numerical approach can appropriately model the heat transport processes pertaining to heat recovery from EGS reservoirs.

Wu, Hui↗
DOE OSTI2022

EGS Collab Experiment 2: Earth Model Datasets

The EGS Collab Project performed a series of tests to increase the understanding the response of crystalline rock mass to stimulations and fluid circulation to efficiently implement enhanced geothermal systems (EGS) technologies. The EGS Collab team created two underground testbeds at the Sanford Underground Research Facility (SURF) in Lead SD at a depth of approximately 1.5 km (4850 level) and 1.25 km (4100 level) to examine hydraulic fracturing and hydraulic shearing, respectively. Experiment 2 was designed to examine hydraulic shearing and fluid flow in testbed 2 in amphibolite under a controlled set of stress and fracture conditions. This document summarizes the general geology, natural fractures, and conceptual model(s) of stimulated fracture networks in the testbed 2. The dataset package included here are input and output products associated with Earth Models for the EGS Collab Testbed 2. The earth model datasets are included in the whole package (project) in Leapfrog file format. Also, datasets are given in primary input file format (csv).

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Efforts and Innovations to Promote Data Sharing and Data Accessibility in the EGS Collab Experiments

Large-scale scientific research programs such as the EGS Collab experiments and the FORGE program play extremely important roles in advancing geothermal technologies. Such efforts involve a large number of researchers from multiple institutions, last multiple years, and generate large, complex datasets. The value of the research efforts is only realized when the datasets are used by a large community of researchers in the decades to come. A challenge is that due to the complexity of the data, it could require a user to devote a serious effort into understanding the data before the data can be effectively utilized. In the EGS Collab experiments, the team has devoted remarkable efforts and developed many innovative solutions to make the data more accessible to broader team members and future users. This paper documents the experience gained and lessons learned by the EGS Collab team in disseminating the data in the most informative and inspiring forms to maximize the value of this precious dataset. "Accessibility"in the title does not only mean making the raw data available for download. Particularly, we want to emphasize the importance of organizing, annotating, and presenting the data in ways to make it easy to digest by prospective consumers of the data.

circulation↗
DOE OSTI2024

The EGS Collab project: Outcomes and lessons learned from hydraulic fracture stimulations in crystalline rock at 1.25 and 1.5 km depth

With the goal of better understanding stimulation in crystalline rock for improving enhanced geothermal systems (EGS), the EGS Collab Project performed a series of stimulations and flow tests at 1.25 and 1.5 km depths. The tests were performed in two well-instrumented testbeds in the Sanford Underground Research Facility in Lead, South Dakota, United States. The testbed for Experiment 1 at 1.5 km depth contained two open wells for injection and production and six instrumented monitoring wells surrounding the targeted stimulation zone. Four multi-step stimulation tests targeting hydraulic fracturing and nearly year-long ambient temperature and chilled water flow tests were performed in Experiment 1. The testbed for Experiments 2 and 3 was at 1.25 km depth and contained five open wells in an outwardly fanning five-spot pattern and two fans of well-instrumented monitoring wells surrounding the targeted stimulation zone. Experiment 2 targeted shear stimulation, and Experiment 3 targeted low-flow, high-flow, and oscillating pressure stimulation strategies. Hydraulic fracturing was successful in Experiments 1 and 3 in generating a connected system wherein injected water could be collected. However, the resulting flow was distributed dynamically, and not entirely collected at the anticipated production well. Thermal breakthrough was not observed in the production well, but that could have been masked by the Joule-Thomson effect. Shear stimulation in Experiment 2 did not occur - despite attempting to pressurize the fractures most likely to shear - because of the inability to inject water into a mostly-healed fracture, and the low shear-to-normal stress ratio. The EGS Collab experiments are described to provide a background for lessons learned on topics including induced seismicity, the correlation between seismicity and permeability, distributed and dynamic flow systems, thermoelastic and pressure effects, shear stimulation, local geology, thermal breakthrough, monitoring stimulation, grouting boreholes, modeling, and system management.

15 - GEOTHERMAL ENERGY↗
DOE OSTI2024

Detecting fractures and monitoring hydraulic fracturing processes at the first EGS Collab testbed using borehole DAS ambient noise

Enhanced geothermal systems (EGS) require cost-effective monitoring of fracture networks. We validate the capability of using borehole distributed acoustic sensing (DAS) ambient noise for fracture monitoring using core photos and core logs. The EGS Collab project has conducted 10 m scale field experiments of hydraulic fracture stimulation using 50–60 m deep experimental wells at the Sanford Underground Research Facility (SURF) in Lead, South Dakota. The first EGS Collab testbed is located at 1616.67 m (4850 ft) depth at SURF and consists of one injection well, one production well, and six monitoring wells. All wells are drilled subhorizontally from an access tunnel called a drift. The project uses a single continuous fiber-optic cable installed sequentially in the six monitoring wells to record DAS data for monitoring hydraulic fracturing during stimulation. We analyze 60 s time records of the borehole DAS ambient noise data and compute the noise root-mean-square (rms) amplitude on each channel (points along the fiber cable) to obtain DAS ambient noise rms amplitude depth profiles along the monitoring wellbore. Our noise rms amplitude profiles indicate amplitude peaks at distinct depths. We compare the DAS noise rms amplitude profiles with borehole core photos and core logs and find that the DAS noise rms amplitude peaks correspond to the locations of fractures or lithologic changes indicated in the core photos or core logs. We then compute the hourly DAS noise rms amplitude profiles in two monitoring wells during three stimulation cycles in 72 h and find that the DAS noise rms amplitude profiles vary with time, indicating the fracture opening/growth or closing during the hydraulic stimulation. Our results demonstrate that borehole DAS passive ambient noise can be used to detect fractures and monitor fracturing processes in EGS reservoirs.

58 GEOSCIENCES↗
DOE OSTI2021

EGS Collab Experiment 1: Circulation Testing Processed data

This submission includes processed and reduced data for circulation testing that was conducted at the 164' fracture on the 4850 ft level of the Sanford Underground Research Facility. The circulation tests were done to test the flow through the 164' fracture in the EGS Collab Experiment 1 testbed on the 4850 ft level of the Sanford Underground Research Facility in order to validate computer models concerned with flow processes and heat exchange processes in EGS. This data was processed from raw data that is available in the GDR submission linked below: "EGS Collab Circulation Testing Raw Data and Documentation." Python scripts used to process and reduce the data are included. The scripts also serve as "documentation" as well as examples for data processing. More information about the test itself as well as the rationale and process of data processing is available at wiki page linked below.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Hydro-mechanical measurements and x-ray imaging of sheared crystalline rock fractures from EGS Collab experiments 1 & 2

Measuring hydro-mechanical properties of natural fractures is a prerequisite for optimizing hydraulic stimulation design and well placement. We completed experiments to characterize shear on natural fractures in schist, amphibolite, and rhyolite specimens drilled from EGS Collab Project’s field sites at the Sanford Underground Research Facility (SURF) in South Dakota. A triaxial direct shear method and coupled x-ray imaging were used to perform hydroshearing and mechanical shearing at the site’s in-situ stress conditions. This produced simultaneous measurements of fracture and matrix strength, permeability, stress-dependent aperture, dilation, and friction strength. Our results identified that only a subset of the natural fractures was weak enough for hydroshearing. Generally, hydroshearing increases fracture permeability by a factor of 10 or more and the enhancement is retainable over time. However, the shear slip does not always result in permeability enhancement. High content of phyllosilicates was found to associate with exceptionally weak fractures that also exhibited poor or even negative enhancement after stimulation. Combining our measurements with site data, we can predict that most observable fractures at the two EGS Collab sites do not meet the criteria for hydroshearing before tensile opening. In some cases, the visible fractures are low permeability and as strong as the adjacent rock. To induce hydroshearing before tensile opening, injection must target known weak and favorably oriented fractures with confirmed pre-existing permeability.

58 GEOSCIENCES↗
DOE OSTI2022

Hydro-Mechanical Measurements of Sheared Crystalline Rock Fractures With Applications for EGS Collab Experiments 1 and 2

We present hydro-mechanical measurements that characterize shear on natural fractures in schist, amphibolite, and rhyolite specimens from the enhanced geothermal system (EGS) Collab Project's Experiment 1 and 2 sites (E1 and E2) at the Sanford Underground Research Facility. We employed a triaxial direct shear method augmented with X-ray imaging to perform hydroshearing (injection-induced shearing) and mechanical shearing on naturally fractured specimens at in situ stress conditions. Measurements included fracture permeability, strength, stress-dependent aperture, shear dilation, and frictional strength. Results reveal that in situ natural fractures must be permeable, weak, and shear-oriented to be hydrosheared, and only a subset of the observable in situ fractures were suitable. When sheared, the fracture permeability typically increased by a factor of 10 or more and this increase was retained over time. However, shear slip did not always result in permeability increase. High phyllosilicate content associated with exceptionally weak fractures exhibited poor or even decreased permeability after stimulation. These measurements in combination with site data were used to conduct a slip-tendency analysis for different fracture sets, and we selected the top candidate natural fractures for hydroshearing at the EGS Collab sites. We also found that the lower in situ shear stress and stronger fractures at the E2 site make hydroshearing more challenging than at the E1 site. Overall, the methods and analysis used in our work can be applied to any geothermal project to identify in situ joint sets that are best suited for hydroshearing, which in turn can help to optimize well placement and energy production.

58 GEOSCIENCES↗
DOE OSTI2022

Computed Tomography Scanning and Geophysical Measurements of the Enhanced Geothermal Systems (EGS) Collab SURF Core

The computed tomography (CT) facilities and the Multi-Sensor Core Logger (MSCL) at the National Energy Technology Laboratory (NETL) in Morgantown, West Virginia were used to characterize core from 8 wells from the Enhanced Geothermal Systems (EGS) Collab project located in the Sanford Underground Research Facility’s (SURF) 4850 level. The work in this report falls in Experiment 1 in a three-phase experiment, with the primary purpose to increase understanding of hydraulic fracturing. The primary impetus of this work is a collaboration between U.S. Department of Energy (DOE) and the EGS Collab. The resultant datasets are presented in this report and can be accessed from NETL's Energy Data eXchange (EDX) online system using the following link: https://edx.netl.doe.gov/dataset/surf-collab-core. All equipment and techniques used were non-destructive, enabling future examinations and analyses to be performed on these cores. None of the equipment used was suitable for direct visualization of the pore space in the core, although fractures and discontinuities were detectable with the methods tested. Low resolution CT imagery with the NETL medical CT scanner was performed on the entire core. Qualitative analysis of the medical CT images, coupled with X-ray fluorescence (XRF), P-wave, and magnetic susceptibility measurements from the MSCL were useful in identifying zones of interest for more detailed analysis as well as fractured zones. The ability to quickly identify key areas for more detailed study with higher resolution will save time and resources in future studies. The combination of methods used provides a multi-scale analysis of the core; the resulting macro and micro descriptions are relevant to many subsurface energy related examinations traditionally performed at NETL.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Simulation of Chilled-water Injection at EGS Collab Testbed 2 using the GEOS simulation framework

This work seeks to model the chilled-water injection that occurred at EGS Collab Testbed 2 as part of experiment 3, using the open-source GEOS simulation framework. Modeling of this process, previously conducted using STOMP-GT, confirmed that thermal breakthrough was expected to occur during the chill water injection and may have been masked by strong Joule-Thompsons effects induced by large pressure drops between the fractures and the production wells. Building a GEOS numerical model of this process will allow to include additional physics. In fact, GEOS can model fully coupled thermo-poromechanical processes in fractured porous media and can be employed to model the process of artificially enhancing rock permeability by hydraulically fracturing the rocks. For example, the GEOS model could help understanding the dynamic nature of the EGS collab experiment 3 flow system. Since the limited time and resources do not allow for an extensive study, the focus is on building a baseline model of this process. As such, the main outcomes of this modelling efforts are listed below.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

EGS Stimulation Design with Uncertainty Quantification at the EGS Collab Site

Engineering a robust hydraulic connection between wells is one of the most difficult aspects of enhanced geothermal systems (EGS). Designing and constructing such hydraulic connections requires and understanding of the in situ state of stress and the heterogeneities and discontinuities that naturally exist and may control the stimulation. Even with comprehensive stress and formation characterization programs substantial uncertainty remains in these key parameters. This is especially the case in high-temperature EGS environments where drilling conditions are often difficult and a far fewer logging and testing options are available. This paper presents a new approach for explicitly quantifying the uncertainties in the state of stress using a Bayesian Markov Chain Monte Carlo method. This approach produces a probability distribution for the stress tensor, including a general 3D orientation, that reflects the uncertainties in all the observations or indicators used to constrain the stress state. This method is demonstrated on the characterization data for the EGS Collab Experiment 2 site. The output of the analysis is used to guide the design of the planned stimulations. In the case of research projects like EGS Collab, explicitly quantifying the uncertainties in the stress state allow for more rigorous hypothesis testing by allowing conclusions drawn from the experiments to be interpreted in the context of the uncertain knowledge about conditions in the test bed.

Burghardt, Jeffrey A.↗
DOE OSTI2021

Field Experiments and Model Validation: The EGS Collab Project

Implementing enhanced geothermal systems (EGS) will require improvements in understanding stimulation of crystalline rock to create appropriate flow pathways, and the ability to effectively simulate both the stimulation and the flow and transport processes in the resulting fracture network. The US Department of Energy (DOE) is addressing these and other challenges at multiple scales. The EGS Collab project, addressed here, is performing tests and modeling at the 10 m scale. The FORGE project is performing tests at the full reservoir scale. The EGS Collab team created an underground testbed at the Sanford Underground Research Facility (SURF) in Lead, South Dakota, at a depth of approximately 1.5 km to examine hydraulic fracturing (Experiment 1). We are currently building a second testbed at SURF at a depth of about 1.25 km aimed at investigating shear stimulation (Experiment 2). In Experiment 1, we drilled eight boreholes in a well-characterized phyllite and installed geophysical sensors in six of them to create a well-instrumented testbed to allow careful monitoring of stimulation events and flow tests. Numerical simulation was used to answer key experimental design questions, to forecast fracture propagation trajectories and extents, and to analyze and evaluate results both in near-real-time and in detailed process studies. Stimulations performed in this testbed allowed quantification of processes occurring during stimulation and the examination of dynamic flow occurrences. Long-term ambient temperature and chilled water flow tests were performed in addition to many tracer tests to examine system behavior. Our second testbed, targeted at shear stimulation, is currently being built at the SURF Facility at a depth of about 1.25 km in amphibolite under a different set of stress and fracture conditions than Experiment 1.

artificial intelligence↗
DOE OSTI2022

EGS Collab Experiment 2: Results of Tracer Tests

Multiple sets of tracer tests were conducted at the EGS Collab Testbed 2 on the 4100 L at the Sanford Underground Research Facility (SURF), Lead, SD. The enclosed data package includes: tracer recovery results, water balance calculations and rationales, water flow measurement for north ditch, (manual) water flow measurements at different production points, and a tracer-interpretation paper presented at the Stanford Geothermal Workshop, 2023.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Monitoring spatiotemporal evolution of fractures during hydraulic stimulations at the first EGS collab testbed using anisotropic elastic-waveform inversion

The EGS Collab project acquired continuous active-source seismic monitoring (CASSM) data before, during, and after hydraulic stimulations at the first testbed at the depth of 4850 ft (1478 m) at the Sanford Underground Research Facility in Lead, South Dakota, for monitoring fracture creation and evolution. CASSM acquisition was conducted using 24 hydrophones, 18 accelerometers, and 17 piezoelectric sources within four fracture-parallel wells and two orthogonal wells. 3D anisotropic traveltime tomography and anisotropic elastic-waveform inversion of the campaign cross-borehole seismic data show that the rock within the stimulation region is a heterogeneous horizontal transverse isotropic medium. Here we use these inversion results as the initial models and apply 3D anisotropic first-arrival traveltime tomography and 3D anisotropic elastic-waveform inversion to the CASSM data acquired after each stimulation in May, 2018 and December, 2018. We observe the spatiotemporal evolution of seismic velocities and anisotropic parameters caused by hydraulic fracture stimulations, showing the regions of rock alternation caused by hydraulic fracture stimulation.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Close Observation of Hydraulic Fracturing at EGS Collab Experiment 1: Fracture Trajectory, Microseismic Interpretations, and the Role of Natural Fractures

Abstract Despite the wide application of hydraulic fracturing in enhanced geothermal system (EGS) development and unconventional hydrocarbon production, our understanding of the many factors affecting the propagation of hydraulic fractures has relied on circumstantial evidence. This is partly due to the scarcity of direct observations in the subsurface. The EGS Collab project attempts to address these issues in the context of EGS research by performing intermediate‐scale (∼10 m) hydraulic stimulation experiments in a thoroughly characterized and heavily instrumented underground testbed. This paper analyzes the data collected from the first suite of hydraulic fracturing tests in this testbed, consisting of seven stimulation episodes. High‐quality microseismic data delineate five planar features very clearly. Combining fracture‐wellbore intersection observations from distributed temperature sensing (DTS) and visual observations from an open‐hole well, as well as prior in‐situ stress measurements, we conclude with high certainty that the four larger planes were hydraulic fractures. The growth of the hydraulic fractures was temporarily halted by a prominent, open natural fracture in the testbed but they eventually crossed and slightly reoriented under continued stimulation. Mineral‐filled (i.e., healed) natural fractures, though prevalent in the testbed, did not have perceivable effects on hydraulic fracture propagation. The high‐quality, mutually corroborating data sets allowed conclusions to be drawn with high confidence and attests to the advantage of intermediate‐scale experiments in subsurface research.

58 GEOSCIENCES↗
DOE OSTI2022

EGS Collab: Modeling and Simulation Working Group Teleconference Series (99-128)

This submission contains the presentation slides and recordings from EGS Collab Modeling and Simulation Working Group (MSWG) teleconferences number 99 through 128. These teleconferences served three objectives for the project: 1) share simulation results, 2) communicate field activities and results to the simulation teams, and 3) hold open scientific discussions on EGS topics.

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

EGS Collab Experiment 2: Continuous Broadband Seismic Waveform Data

Two broadband seismometers were installed on the 4100 level and recorded for the duration of EGS Collab Experiment #2. Inspired by published data from similar instruments installed in the Aspo Hard Rock Lab, these long-period instruments aimed to measure the tilting of the drift in response to the injection of fluid into the testbed. One instrument was installed underneath the wellheads in Site A (aka the "battery" alcove) and the other was installed along the east wall of the drift, south of Site B. Due to the feet of gravel (ballast) laid along the floor of the drift, we were unable to anchor the sensors directly to the rock. As a result, the coupling of the sensors to the experiment rock volume is likely poor. In addition, there are a number of noise sources that complicate the interpretation of the data. For example, sensor BBB is installed adjacent (within 3 ft) to the rail line that runs towards the Ross shaft. Trains (motors) run along this line almost daily and produce a large signal in these data. Careful extraction of periods of interest, as well as filtering for specific signals, is necessary. The sensors are Nanometrics Trillium Compact Posthole seismometers, sensitive down to 120 seconds period. They were installed as close to the drift wall and as deep as we could manually excavate (only about 1 ft or so). The holes were leveled with sand and the sensors were placed on a paver before backfilling with sand. The hole was then covered by a bucket filled with insulation to improve the sensor's isolation from daily temperature variations, which are minor but present due to drift ventilation from the surface. Data were recorded on Nanometrics Centaur digitizers at 100 Hz. The full response information is available in the StationXML file provided here, or by querying the sensors through the IRIS DMC (see links below). These instruments were provided free of charge through the IRIS PASSCAL instrument center. The network code is XP and the station codes are BBA and BBB. The waveform data can be queried through the IRIS FDSN server using any method the user likes. One convenient option is to use the Obspy python package: https://docs.obspy.org/packages/obspy.clients.fdsn.html

15 GEOTHERMAL ENERGY↗