Search NASA⌕ Search

SEARCH · Search NASA

Results for “Commercially pure titanium”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

ECCI based characterization of dislocation shear in polycrystalline arrays during heterogeneous deformation of commercially pure titanium

A new electron channeling contrast imaging (ECCI) based approach for the characterization of heterogeneous plastic deformation across multiple grains in a polycrystal is presented. The nature of the shear accommodation at grain boundaries has been assessed by evaluating the spatial distribution of dislocations and slip system activities near the boundaries and relating these observations to standard slip transfer criteria and the global state of stress. The direction of slip band propagation, and consequently the location of dislocation slip band nucleation, was determined by characterizing the slip band widths across individual grains. This assessment leads to a better understanding of the factors involved in polycrystalline deformation, including the grain boundary shear accommodation associated with both dislocation pile-ups and grain boundary dislocation nucleation. Because ECCI allows study of dislocation structures over large surface areas, and thus larger overall volumes than typically are accessible by other techniques, the overall approach allows the dislocation distribution across individual grains to be understood in terms of the broader polycrystalline constraints.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Mechanical Behavior of Commercially Pure Titanium Weldments at Lower Temperatures

Commercially pure titanium is used for low-temperature applications due to good toughness attributed to single-phase microstructure (α). Electron beam welding (EBW) and gas tungsten arc welding (GTAW) processes have been used for welding two grades of commercially pure titanium (Grade 2 and Grade 4). Martensitic microstructure is found to be finer in the case of EBW joint as compared to GTAW joint due to faster rate of cooling in the former process. Weldments have been characterized to study the mechanical behavior at ambient (298 K) and cryogenic temperatures (20 and 77 K). Strength of weldments increases with the decrease in temperature, which is found to be more prominent in case of Grade 4 titanium as compared to Grade 2. Weld efficiency of Grade 4 is found to be higher at all the temperatures (ambient, 77 and 20 K). However, ultimate tensile strength/yield strength ratio is higher for Grade 2 as compared to Grade 4. % Elongation is found to increase/retained at cryogenic temperatures for Grade 2, and it is found to decrease for Grade 4. Electron backscattered diffraction analysis and transmission electron microscopy of deformed samples confirmed the presence of extensive twinning in Grade 2 and the presence of finer martensitic structure in Grade 4. Fractography analysis of tested specimens revealed the presence of cleavage facets in Grade 4 and dimples in specimens of Grade 2. Higher strength in Grade 4 is attributed to higher oxygen restricting the twin-assisted slip, which is otherwise prominent in Grade 2 titanium.

36 MATERIALS SCIENCE↗
NASA NTRS2012

Effects of Long-Term Thermal Exposure on Commercially Pure Titanium Grade 2 Elevated-Temperature Tensile Properties

Elevated-temperature tensile testing of commercially pure titanium (CP Ti) Grade 2 was conducted for as-received commercially produced sheet and following thermal exposure at 550 and 650 K (531 and 711 F) for times up to 5000 h. The tensile testing revealed some statistical differences between the 11 thermal treatments, but most thermal treatments were statistically equivalent. Previous data from room temperature tensile testing was combined with the new data to allow regression and development of mathematical models relating tensile properties to temperature and thermal exposure. The results indicate that thermal exposure temperature has a very small effect, whereas the thermal exposure duration has no statistically significant effects on the tensile properties. These results indicate that CP Ti Grade 2 will be thermally stable and suitable for long-duration space missions.

Ellis, David L.↗
DOE OSTI2018

Effect of laser power on oxygen and nitrogen concentration of commercially pure titanium manufactured by selective laser melting

Highlights: • The hardness and strength of pure titanium fabricated by SLM were increased with increasing the laser power. • During the SLM processing, the concentrations of oxygen and nitrogen in the SLM parts were increased. • The oxidation and nitriding were thermodynamically possible under SLM. - Abstract: This study analyzed the variation of mechanical properties and its causes with increasing the laser power in the fabrication of pure titanium by selective laser melting (SLM). SLM samples were fabricated using commercially pure titanium grade 1 powder when the scan speed was 1000 mm/s and the laser power as 120, 200, 280, 360, and 440 W, respectively. As the laser power increased, the hardness and strength of the samples increased gradually. During the SLM processing, the concentrations of oxygen and nitrogen in the SLM samples were increased, which resulted in the increase of hardness and strength. The SLM equipment used in this study removed oxygen in the chamber by flowing high purity argon gas and fabricates the sample while preserving the oxygen concentration in the atmosphere to 0.2%. Evaluating the possibility of oxidation and nitriding during the SLM process by thermodynamic analysis, it was found that the process occurred under conditions in which temperature and residual oxygen and nitrogen partial pressure led to oxidation and nitriding.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of pre-annealing deformation on the recrystallized texture and grain boundary misorientation in commercial pure titanium

Highlights: • Tailoring the misorientation angle distribution by pre-annealing rolling in CP-Titanium. • Enhancing the inheritance of basal scatter texture by medium pre-annealing rolling. • Moderate pre-annealing rolling produces refined recrystallized grains. - Abstract: The effects of rolling reduction followed by annealing (at 650 °C) on commercial pure titanium sheet are investigated. The microstructure, texture and misorientation angle distributions after rolling and annealing are observed by electron back scatter diffraction (EBSD). It is found that, when the rolling deformation was low (20%) or medium (40%), a fraction of non-TD-split basal texture is inherited from the deformed state and remains even after long time (60 min) annealing. However, heavy rolling deformation (85%) causes a strong and typical TD-split basal texture in the deformed and annealed states. In addition, the misorentation angle distributions are relatively homogeneous for the recrystallized samples with a low or medium pre-annealing deformation. But with heavy pre-annealing deformation, the misorientation angle distributions exhibits two peaks, around 15–30° and 70–80°. The texture and misorientation angle evolution mechanisms are discussed in this work. The study shows the possibility to tailor the texture and the misorientation angle distribution of commercial pure titanium sheet by ordinary rolling process.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Creep Behavior of Commercially Pure Titanium TA2 After Supersonic Fine Particles Bombardment

In this study, the effect of supersonic fine particles bombardment (SFPB) on the creep behavior of commercially pure titanium TA2 was investigated. Microstructural observations with x-ray diffraction and a transmission electron microscope indicated that the grain size of the TA2 surface layer was refined to nanometer scale in the topmost surface layer after SFPB treatment. Indentation creep tests showed that the SFPB-treated sample had a lower maximum depth and higher hardness than the original sample at the same load, indicating an enhancement of the surface strength with SFPB. With lower creep displacements, the creep resistance was also improved after SFPB treatment. The maximum creep rate under different loading conditions showed obvious loading time and load dependencies. The maximum creep rate of the SFPB-treated sample was lower than the original sample for all test conditions, and the maximum creep strain rate of the SFPB-treated sample was similar to that of the original sample. The indentation stress of the SFPB-treated sample was higher than the original sample, while the creep stress exponent of the original sample was slightly higher than for the SFPB-treated sample, with no obvious variation tendency with different loading times or loads.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Damage evolution and ductile fracture of commercially-pure titanium sheets subjected to simple tension and cyclic bending under tension

This paper describes a study into the evolution of damage in commercial-purity titanium (CP–Ti) sheets subjected to cyclic bending under tension (CBT) and uniaxial tension (simple tension, ST). Sections were taken from sheets that were strained to various levels under both methods and were imaged using X-ray computed tomography (XCT) to reveal insights into the size, density, and distribution of microvoids in the sheets. Digital image correlation (DIC) was also used to observe the surface strain of CBT and ST sheets during testing. These results showed that elongation to failure (ETF) for CBT deformation is about 2.5× higher than for ST, local longitudinal strains in the bulk of the CBT sample are around 1.3× higher than the peak strain in the ST necked region, and 1.7× higher in the localized region of CBT failure. It was found that the volume-density of voids in both sheets followed a similar exponential increase with strain, reaching nearly 45× higher in the CBT than the ST sheets before the onset of failure, mainly due to the higher strain levels achieved. A higher volume density of voids developed in the center of sheets at high levels of strain, for both processes, with the density in the sheet center becoming approximately double that found near the edges. Scanning electron microscopy (SEM) was used to examine the fracture surface of CBT and ST sheets after failure. The observations are presented and discussed highlighting the CBT process as effective to delay ductile fracture of the CP-Ti sheets.

Commercially pure titanium↗
DOE OSTI2026

Low-Pressure Diffusion Bonding of Vanadium to Commercially Pure Titanium and Ti-6Al-4V

Modern technology increasingly requires components to be made from specific high-performance materials. To support complex multi-metal structures, a variety of techniques are required to join dissimilar metal parts with precise shapes. This study evaluates vacuum diffusion bonding as a method for joining titanium and vanadium, focusing on both pure titanium and the common alloy Ti-6Al-4V. We employ modest pressure provided by a weight and simple surface preparation to simulate the most commercially applicable process. Here, we show that Ti-6Al-4V alloy bonds readily to V, forming a continuous, clearly defined interdiffusion layer with predictable kinetics. Conversely, commercially pure Ti forms a crack-prone bond with V that fails to improve at higher bonding temperatures or longer times. We attribute this failure to the concentration of stress caused by the ß-to-α phase transformation in Ti. The contrasting bonding efficacy between pure Ti and the alloy provides insight into the crystallographic interactions that occur at the interface during bonding and cooling. These results provide surprising insight into a new method for bonding Ti alloys to V and possibly other metals that share the body-centered cubic crystal structure.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Planar Anisotropy, Tension–Compression Asymmetry, and Deep Drawing Behavior of Commercially Pure Titanium at Room Temperature

The planar anisotropy (PA) and tension–compression asymmetry (TCA) of the CP-Ti were investigated via uniaxial tension and compression tests at room temperature. The formability and the earing behavior of the CP-Ti sheet were studied via deep drawing experiment. The deep drawing simulations using the uniaxial tensile and the compressive curves as the hardening rules were compared with each other and with the experimental results. The CP-Ti sheet showed PA and TCA in yielding and strain hardening. The PA was characterized by the plastic strain ratio r{sub 0}, r{sub 45}, and r{sub 90} of 1.47, 2.06, and 2.05. The TCA showed PA, which showed tension–compression yield strength ratios of 1.12, 1.08, and 1.04 in 0°, 45°, and 90° in the rolling direction, and tensile and compressive hardening exponent ratios of 0.86, 0.8, and 0.62. The orientation distribution functions (ODFs) analysis demonstrated that the tensile and the compressive deformation textures were different and showed PA. The simulative results, including the simulated forming force and the earing profiles using the uniaxial tensile and compressive curves as the hardening rules, were not in agreement with each other. The results were not in good agreement with the experimental results, implying that the TCA had an important effect on the formability of the sheet. The TCA tended to reduce the thickness of the deep drawing parts, increase the earing ratio, and affect the drawing force.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Gas phase hydrogen permeation in alpha titanium and carbon steels

Commercially pure titanium and heats of Armco ingot iron and steels containing from 0.008-1.23 w/oC were annealed or normalized and machined into hollow cylinders. Coefficients of diffusion for alpha-Ti and alpha-Fe were determined by the lag-time technique. Steady state permeation experiments yield first power pressure dependence for alpha-Ti and Sievert's law square root dependence for Armco iron and carbon steels. As in the case of diffusion, permeation data confirm that alpha-titanium is subject to at least partial phase boundary reaction control while the steels are purely diffusion controlled. The permeation rate in steels also decreases as the carbon content increases. As a consequence of Sievert's law, the computed hydrogen solubility decreases as the carbon content increases. This decreases in explained in terms of hydrogen trapping at carbide interfaces. Oxidizing and nitriding the surfaces of alpha-titanium membranes result in a decrease in the permeation rate for such treatment on the gas inlet surfaces but resulted in a slight increase in the rate for such treatment on the gas outlet surfaces. This is explained in terms of a discontinuous TiH2 layer.

Johnson, D. L.↗
NASA NTRS2018

Characterization of Titanium Alloys Produced by Electron Beam Directed Energy Deposition

Functionally graded materials offer the potential to improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a component. Additive manufacturing techniques enable the fabrication of such graded materials and structures. While examining several titanium alloys, this paper focuses on Ti-8Al-1Er as it has a unique microstructure that is only feasible when produced by rapid solidification methods like electron beam directed energy deposition, an additive manufacturing process. The results show that, when mixed, Ti-8Al-1Er and commercially-pure titanium uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. At discontinuous interfaces between Ti-8Al-1Er and commercially-pure titanium, the crack growth behavior progresses smoothly across the discontinuity as the crack transitions from one crack growth regime into another. Studies on monolithic samples shows the mechanisms of damage in the Ti-8Al-1Er; specifically, that strain localization occurs near grain boundaries of high mis-orientation on the microscale and that twinning and dislocation density is concentrated near erbia-strengthening particles (Er2O3) on the nanoscale.

Newman, John A.↗
DOE OSTI2020

ECCI analysis of shear accommodations at grain boundaries in commercially pure alpha titanium

This study uses a novel approach that couples electron channeling contrast imaging (ECCI) with controlled removal of surface material to investigate the slip system/grain boundary interactions by assessing the geometry of slip planes and grain boundaries as a function of depth. The comparison of spacing, relative distributions, and correlations of slip bands across grain boundaries reveals surface biasing on the slip band behavior in the grain boundary region. Furthermore, using analysis of the compatibility factor m’, the Schmid factor of each slip system, and the angles θ between slip planes, a more comprehensive understanding of the details of the mechanisms of strain transfer and heterogeneous deformation is developed. In general, the misalignment of primary slip systems on the grain boundary planes necessitates the activation of secondary accommodating slip systems close to the grain boundary area that are better aligned (higher m’ and lower θ) with respect to the incoming slip system across the grain boundary. Such systems have the same Burgers vector as the primary slip systems within the respective grains, but are typically on low mobility slip planes.

59 BASIC BIOLOGICAL SCIENCES↗