Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compression Corner”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Numerical solutions of the Navier-Stokes equations for the supersonic laminar flow over a two-dimensional compression corner

Numerical solutions have been obtained for the supersonic, laminar flow over a two-dimensional compression corner. These solutions were obtained as steady-state solutions to the unsteady Navier-Stokes equations using the finite difference method of Brailovskaya, which has second-order accuracy in the spatial coordinates. Good agreement was obtained between the computed results and wall pressure distributions measured experimentally for Mach numbers of 4 and 6.06, and respective Reynolds numbers, based on free-stream conditions and the distance from the leading edge to the corner. In those calculations, as well as in others, sufficient resolution was obtained to show the streamline pattern in the separation bubble. Upstream boundary conditions to the compression corner flow were provided by numerically solving the unsteady Navier-Stokes equations for the flat plate flow field, beginning at the leading edge. The compression corner flow field was enclosed by a computational boundary with the unknown boundary conditions supplied by extrapolation from internally computed points.

Carter, J. E.↗
NASA NTRS1989

Modeling of turbulence for compression corner flows and internal flows

A compressible Reynolds averaged Navier-Stokes code is applied to examine the performances of basic turbulence models for unseparated and separated flows. The turbulence models considered are a zero-equation model and several two-equation models, including a new k-epsilon model with an eddy viscosity damping function depending upon the Reynolds number and the distance from the wall. The turbulence models are assessed using the following experimental flows: a channel flow, a backward facing step, and a two-dimensional compression corner at Mach 2.8. Discussions and comparisons of the experimental and numerical results are given. Mesh refinement is shown to have a significant beneficial effect on free shear layer flow results obtained with two-equation turbulence models. The results illustrate the usefulness of several turbulence models as a design tool for fluid engineering systems.

Champney, J. M.↗
NASA NTRS1992

An experimental examination of the effects of incoming boundary layer modifications on the dynamics of a turbulent compression corner interaction

This experimental study examines the effects of modifications to the incoming turbulent boundary layer on the highly separated shock wave/boundary layer interaction generated by an unswept compression corner. Particular focus is placed on the motion of the unsteady separation shock wave. The flowfield was generated by a 28 deg ramp in a Mach 5 flow with a freestream Reynolds number of 50 x 10 exp 6/m. The incoming turbulent boundary layer transitioned naturally and developed under near-adiabatic wall conditions. Modification of the flow entering the interaction was effected through either a single plate boundary layer manipulator (BLM) or riblets. The BLM reduced the length of separation by 35-45 percent and reduced the streamwise extent of the separation shock motion by 36-74 percent. Examination of the flowfield downstream of the BLM showed this result to be due to the inviscid preturning of the flow by the BLM, and not by changes to the boundary layer dynamics. The riblets had no measurable effect on the compression corner interaction.

Mcclure, W. B.↗
NASA NTRS2011

Uncertainty Assessments of 2D and Axisymmetric Hypersonic Shock Wave - Turbulent Boundary Layer Interaction Simulations at Compression Corners

This paper is one of a series of five papers in a special session organized by the NASA Fundamental Aeronautics Program that addresses uncertainty assessments for CFD simulations in hypersonic flow. Simulations of a shock emanating from a compression corner and interacting with a fully developed turbulent boundary layer are evaluated herein. Mission relevant conditions at Mach 7 and Mach 14 are defined for a pre-compression ramp of a scramjet powered vehicle. Three compression angles are defined, the smallest to avoid separation losses and the largest to force a separated flow engaging more complicated flow physics. The Baldwin-Lomax and the Cebeci-Smith algebraic models, the one-equation Spalart-Allmaras model with the Catrix-Aupoix compressibility modification and two-equation models including Menter SST, Wilcox k-omega 98, and Wilcox k-omega 06 turbulence models are evaluated. Each model is fully defined herein to preclude any ambiguity regarding model implementation. Comparisons are made to existing experimental data and Van Driest theory to provide preliminary assessment of model form uncertainty. A set of coarse grained uncertainty metrics are defined to capture essential differences among turbulence models. Except for the inability of algebraic models to converge for some separated flows there is no clearly superior model as judged by these metrics. A preliminary metric for the numerical component of uncertainty in shock-turbulent-boundary-layer interactions at compression corners sufficiently steep to cause separation is defined as 55%. This value is a median of differences with experimental data averaged for peak pressure and heating and for extent of separation captured in new, grid-converged solutions presented here. This value is consistent with existing results in a literature review of hypersonic shock-turbulent-boundary-layer interactions by Roy and Blottner and with more recent computations of MacLean.

Gnoffo, Peter A.↗
NASA NTRS1992

Response of a supersonic boundary layer to a compression corner

On the basis of direct numerical simulations of rapidly compressed turbulence, Zeman and Coleman have developed a model to represent rapid directional compression contribution to the pressure dilatation term in the turbulent kinetic energy equation. The model has been implemented in the CFD code for simulation of supersonic compression corner flow with an extended separated region. The computational results have shown a significant improvement with respect to the baseline solution given by the standard k- epsilon turbulence model which does not contain any compressibility corrections.

Vandromme, D.↗
NASA NTRS1994

Numerical Simulation of Supersonic Compression Corners and Hypersonic Inlet Flows Using the RPLUS2D Code

A two-dimensional computational code, PRLUS2D, which was developed for the reactive propulsive flows of ramjets and scramjets, was validated for two-dimensional shock-wave/turbulent-boundary-layer interactions. The problem of compression corners at supersonic speeds was solved using the RPLUS2D code. To validate the RPLUS2D code for hypersonic speeds, it was applied to a realistic hypersonic inlet geometry. Both the Baldwin-Lomax and the Chien two-equation turbulence models were used. Computational results showed that the RPLUS2D code compared very well with experimentally obtained data for supersonic compression corner flows, except in the case of large separated flows resulting from the interactions between the shock wave and turbulent boundary layer. The computational results compared well with the experiment results in a hypersonic NASA P8 inlet case, with the Chien two-equation turbulence model performing better than the Baldwin-Lomax model.

Kapoor, Kamlesh↗
NASA NTRS1992

Structure of supersonic turbulent flow past a swept compression corner

The structure of the shock wave/turbulent boundary-layer interaction generated by a 3D swept compression corner has been investigated through a combined experimental and theoretical research program. The flowfield geometry is defined by the streamwise compression angle alpha and the sweep angle lambda of the corner. The present study examines two different configurations, namely (alpha, lambda) = (24 deg, 40 deg) and (24 deg, 60 deg) at Mach 3 and Re sigma infinity about 9 x 10 exp 5. The theoretical model is the 3D Reynolds-averaged compressible Navier-Stokes equations with turbulence incorporated using a turbulent eddy viscosity. The calculated flowfields display general agreement with experimental data for surface pressure and good agreement with experimental flowfield profiles of pitot pressure and yaw angle. The principal feature of the flowfield is a large vortical structure approximately aligned with the corner. The entrainment of incoming fluid into the vortical structure is strongly affected by the sweep angle lambda. Viscous (turbulent and molecular) effects appear to be important only in the immediate vicinity of the surface and in an isolated region within the interaction and near the corner.

Knight, Doyle D.↗
NASA NTRS1994

Effects of turbulence compressibility and unsteadiness in compression corner flow

The structure of the separated flow region over a 20 degree compression corner at a free-stream Mach number of 2.84 is investigated computationally using a Reynolds averaged Navier Stokes (R.A.N.S.) solver and kappa-epsilon model. At this Mach number and ramp angle, a steady-state recirculation region of order delta(sub o) is observed, with onset of a 'plateau' in the wall pressure distribution near the corner. At lower ramp angles, separation is negligible, while at an angle of 24 degrees, separation regions of length 2 delta(sub o) are expected. Of interest here is the response of the mathematical model to inclusion of the pressure dilatation term for turbulent kinetic energy. Compared with the experimental data of Smits and Muck (1987), steady-state computations show improvement when the pressure dilatation term is included. Unsteady computations, using both unforced and then forced inlet conditions, did not predict the oscillatory motion of the separation bubble as observed in laboratory experiments. An analysis of the separation bubble oscillation and the turbulent boundary layer (T.B.L.) frequencies for this flow suggests that the bubble oscillations are of nearly the same order as the turbulent frequencies, and therefore difficult for the model to separate and resolve.

Brankovic, A.↗
NASA NTRS1987

Supersonic turbulent flow past a 3-D swept compression corner at Mach 3

Experimental and theoretical studies are presented on the three-dimensional shock wave-turbulent boundary layer interaction generated by a swept compression corner at Mach 3 for compression angle of 24 deg, sweep angle of 60 deg, and Reynolds numbers from 140,000 to 900,000. Two theoretical approaches were used, both of which utilize the full mass-averaged compressible three-dimensional Navier-Stokes equations but differ in the choice of turbulence model (the Baldwin-Lomax, 1978, and the Jones-Launder, 1972, model, respectively). The features of the computed mean flow structure were found to be qualitatively the same for both the Baldwin-Lomax and Jones-Launder models.

Knight, Doyle D.↗
NASA NTRS1988

Supersonic turbulent flow past a swept compression corner at Mach 3. II

The three-dimensional Mach 3.0 shock wave-turbulent boundary layer interaction generated by a swept compression corner whose geometry is characterized by the angle of streamwise compression angle alpha and the angle of sweep lambda is presently treated by the Baldwin-Lomax (1978) algebraic turbulent eddy viscosity model. The results obtained, and those previously derived by means of Cebeci and Smith (1974) and Jones and Launder (1972) models, are compared with experimental measurements. The rate of change of the mean kinetic energy along a streamline is investigated, and evidence is obtained that the flowfield structure is rotational and inviscid.

Knight, Doyle D.↗
NASA NTRS1978

A detailed study of attached and separated compression corner flowfields in high Reynolds number supersonic flow

An experimental study has been carried out to detail the interaction of a compressible turbulent boundary layer with shock waves of varying strengths. The interaction was produced by two-dimensional compression corners of 8, 16, 20, and 24 deg angles. The incoming boundary layer had an edge Mach number of 2.85 and a Reynolds number of 1.7 million based on overall thickness. Detailed mean-flow and surface measurements are presented for the four corner angles. The 8 deg corner flow was found to be fully attached, while the 16 deg case was near incipient separation. Both the 20 deg and 24 deg corners produced significant flow separation regions. In the discussion of these results, emphasis is placed on the development of flowfield properties from attached to separated conditions. Comparisons made with a computational solution of the Navier-Stokes equations show good agreement when the corner flow is not separated.

Settles, G. S.↗
NASA NTRS1976

Diffraction of a shock wave by a compression corner. I - Regular reflection

The unsteady, two-dimensional flowfield resulting from the interaction of a moving planar shock wave with a compression corner is determined using a second-order, discontinuity-fitting, finite-difference approach. The time-dependent Euler equations are transformed to normalize the distance between the body and peripheral shock and to include the existing self-similar property of the flow. The resulting set of partial differential equations in conservation-law form is then solved in a time-dependent fashion using MacCormack's scheme. The vortical singularity, which lies on the body surface, and the single reflected shock are both treated as discontinuities in the numerical procedure. The results of the numerical simulation compare quite favorably with existing experimental interferograms and yield better flowfield resolution than previous first-order, shock-capturing, numerical solutions.

Kutler, P.↗
NASA NTRS1977

Numerical solution of supersonic laminar flow over a three-dimensional compression corner

A newly developed, rapid numerical scheme is extended to three dimensions to solve the complete Navier-Stokes equations for a supersonic, laminar flow over a compression corner with sidewall effects. The program is coded so that it can solve for a general curved ramp surface geometry such as found in inlets and fuselage-wing-flap junctions. A test case of Mach 3.0 flow is calculated. In regions where three-dimensional effects are small, good agreement is obtained between the present calculation and previous two-dimensional solutions. In other regions, the results show complex three-dimensional flow-field interactions including shock-shock and shock/boundary-layer interactions

Hung, C. M.↗
NASA NTRS2015

Evaluation of Industry Standard Turbulence Models on an Axisymmetric Supersonic Compression Corner

Reynolds-averaged Navier-Stokes computations of a shock-wave/boundary-layer interaction (SWBLI) created by a Mach 2.85 flow over an axisymmetric 30-degree compression corner were carried out. The objectives were to evaluate four turbulence models commonly used in industry, for SWBLIs, and to evaluate the suitability of this test case for use in further turbulence model benchmarking. The Spalart-Allmaras model, Menter's Baseline and Shear Stress Transport models, and a low-Reynolds number k- model were evaluated. Results indicate that the models do not accurately predict the separation location; with the SST model predicting the separation onset too early and the other models predicting the onset too late. Overall the Spalart-Allmaras model did the best job in matching the experimental data. However there is significant room for improvement, most notably in the prediction of the turbulent shear stress. Density data showed that the simulations did not accurately predict the thermal boundary layer upstream of the SWBLI. The effect of turbulent Prandtl number and wall temperature were studied in an attempt to improve this prediction and understand their effects on the interaction. The data showed that both parameters can significantly affect the separation size and location, but did not improve the agreement with the experiment. This case proved challenging to compute and should provide a good test for future turbulence modeling work.

Turbulent Boundary Layer↗
NASA NTRSDate not supplied

Unsteady CFD Simulations of a Compression Corner Geometry Using Wall-Modeled LES Methods in Loci/CHEM

Several wall-modeled large eddy simulation (WMLES) methods are tested by simulating an unsteady Mach 2.0 compression corner geometry in Mississippi State’s Loci/CHEM solver. This study is conducted to evaluate the usage and requirements of these WMLES methods for applications regarding fluctuating pressure environments on launch vehicles with computational fluid dynamics (CFD). Two hybrid Reynolds-averaged Navier-Stokes (RANS)-large eddy simulation (LES) methods, Dynamic Hybrid RANS-LES (DHRL) and Improved Delayed Detached Eddy Simulation (IDDES), and one wall-stress-model, the Algebraic Wall Model for Wall-Modeled LES (AWMLES), are tested on varying grid and timestep refinement levels. These grid and timestep sizes are chosen to test the minimum requirements for successfully running these WMLES methods. The simulations are evaluated based on turbulent boundary layer properties in the developed boundary layer as well as unsteady quantities relating to fluctuating pressure environments in the region of the compression corner. The DHRL method shows good agreement with the comparison wind tunnel data and shows good grid and timestep convergence. The results from the IDDES and WMLES simulations show good agreement for several quantities with some discrepancies regarding others. The results presented in this paper will be used to inform further studies in predicting unsteady environments on higher-complexity geometries.

Bryson Frank↗
NASA NTRS1976

Diffraction of a shock wave by a compression corner; regular and single Mach reflection

The two dimensional, time dependent Euler equations which govern the flow field resulting from the injection of a planar shock with a compression corner are solved with initial conditions that result in either regular reflection or single Mach reflection of the incident planar shock. The Euler equations which are hyperbolic are transformed to include the self similarity of the problem. A normalization procedure is employed to align the reflected shock and the Mach stem as computational boundaries to implement the shock fitting procedure. A special floating fitting scheme is developed in conjunction with the method of characteristics to fit the slip surface. The reflected shock, the Mach stem, and the slip surface are all treated as harp discontinuities, thus, resulting in a more accurate description of the inviscid flow field. The resulting numerical solutions are compared with available experimental data and existing first-order, shock-capturing numerical solutions.

Vijayashankar, V. S.↗