Damage & fracture of high-explosive mock subject to cyclic loading
Abstract Not Provided
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract Not Provided
In-situ neutron diffraction during cyclic tension-compression loading (∼+3.5% to −2.8%) of a 17Mn-3Al-2Si-1Ni-0.06C steel that exhibits concurrent transformation and twinning -induced plasticity effects indicated a significant contribution of intragranular back stresses to the observed Bauschinger effect. Rietveld analysis revealed a higher rate of martensitic transformation during tension compared to compression. Throughout cycling, α′-martensite exhibited the highest phase strains such that it bears an increasing portion of the macroscopic load as its weight fraction evolves. On the other hand, the ε-martensite strain remained compressive as it accommodated most of the internal strains caused by the shape misfit associated with the γ→ε and/or ε→α′ transformations.
Abstract not provided
Not Available
Cyclic-loading effects on a nickel-based superalloy are investigated with in-situ neutron-diffraction measurements. The thermoelastic-temperature evolution subjected to cyclic loading is estimated based on the lattice-strain evolution. The atomic thermoelastic responses are compared with the measured bulk temperature evolution. Two transitions in the temperature-evolution are observed. The first transition, observed with the neutron-measurement results, is associated with the cyclic hardening/softening-structural transformation. The second transition is observed at larger number of fatigue cycles. It has a distinct origin and is related to the start of irreversible structural transformations during fatigue. A lattice-strain asymmetry behavior is observed. The lattice-strain asymmetry is quantified as a grain-orientation-dependent transverse/loading parameter (P-ratio). The P-ratio parameter evolution reveals the irreversible plastic deformation subjected to the fatigue. The irreversible fatigue phenomena might relate to the formation of the microcracks. At elevated temperatures the cyclic hardening/softening transition starts at lower fatigue cycles as compared to room temperature. A comparison between the room-temperature and the elevated-temperature fatigue experiments is performed. The P-ratio parameters show the same irreversible trends at both the room and the elevated temperatures.
Cyclic loading of aluminum alloy
In low cycle fatigue, cracks are initiated and propagated under general yielding cyclic loading. For general yielding cyclic loading, Dowling and Begley have shown that fatigue crack growth rate correlates well with the measured delta J. The correlation of da/dN with delta J was also studied by a number of other investigators. However, none of thse studies have correlated da/dN with delta J calculated specifically for the test specimens. Solomon measured fatigue crack growth in specimens in general yielding cyclic loading. The crack tips fields for Solomon's specimens are calculated using the finite element method and the J values of Solomon's tests are evaluated. The measured crack growth rate in Solomon's specimens correlates very well with the calculated delta J.
In low cycle fatigue, cracks are initiated, and propagated under general-yielding cyclic loading. For general-yielding cyclic loading, Dowling and Begley (1976) have shown that fatigue crack growth rate correlates well with the measured Delta J. The correlation of da/dN with Delta J has also been studied by a number of other investigators. However, none of these studies has correlated da/dN with Delta J calculated specifically for the test specimens. Solomon measured fatigue crack growth in specimens in general-yielding cyclic loading. The crack tip fields for Solomon's specimens are calculated, using the finite element method, and the J-values of Solomon's tests are evaluated. The measured crack growth rate in Solomon's specimens correlates very well with the calculated Delta J.
Most of the destructions of machine parts are of fatigue character. Under cyclic loading, the surface layer, in which hardening–softening processes rapidly occur, is formed almost at once after its beginning. The interaction of plastic-deformation traces with each other and with other structural elements, such as grains, results in the formation of a characteristic microstructure of the machine-part surface subject to cyclic loadings. The character of accumulation of slip bands and their shape (narrow, wide, twisting, and broken) depends on the conditions under which (under what factors) the cyclic loading occurs. The fatigue-resistance index expressed in terms of the slope of left portion of the fatigue curve linearized in logarithmic coordinates also depends on the set of relevant factors. The dependence of the surface damageability on the fatigue resistance index makes it possible to implement the method of predicting the fatigue curve by the description of the factors acting on a detail or construction. The position of the inflection point on the curve in the highcycle fatigue region (the endurance limit and the number of loading cycles, the ordinate and abscissa of the inflection point on the fatigue curve, respectively) also depends on the set of relevant factors. In combination with the previously obtained value of the slope of the left portion of the curve in the high-cycle fatigue region, this makes it possible to construct an a priori fatigue curve, thus reducing the scope of required fatigue tests and, hence, high expenses because of their long duration and high cost. The scope of tests upon using the developed method of prediction may be reduced to a minimum of one or two samples at the predicted level of the endurance limit.
For several years the nonlinear energy method proposed by Liebowitz and Eftis has been examined as a failure criterion for static testing of center-cracked and compact tension specimens. Since the method appears to be valid under conditions of crack-tip plasticity, subcritical crack growth and load relaxation, tests have been conducted to ascertain the merit of this method as a failure criterion under cyclic loading conditions. The nonlinear energy toughness for cyclic loading is obtained from an envelope of the cyclic load-displacement record, which naturally imposes some restrictions on the loading program. The cyclic toughness parameter has been evaluated for thin center-cracked sheets of 2024-T3 and 7075-T6 aluminum alloys. Both alloys exhibited a significant reduction of the cyclic toughness parameter with increasing cyclic life in a manner similar to the classical S-N diagram. It is suggested that this method may serve the design process by allowing the establishment of a fracture toughness parameter capable of including the effects of the entire loading history of a structure into the fracture toughness requirements.
An elastic-plastic (incremental) finite-element analysis, in conjunction with a crack-growth criterion, was used to study crack-growth behavior under monotonic and cyclic loading. The crack-growth criterion was based on crack-tip strain. Whenever the crack-tip strain equals or exceeds a critical strain value, the crack grows. The effects of element-mesh size, critical strain, strain hardening, and specimen type (tension or bending) on crack growth under monotonic loading were investigated. Crack growth under cyclic loading (constant amplitude and simple variable amplitude) were also studied. A combined hardening theory, which incorporates features of both isotropic and kinematic hardening under cyclic loading, was also developed for smooth yield surfaces and was used in the analysis.
A methodology to compute the fatigue life for different ratios, r, of applied stress to the laminate strength based on first ply failure criteria combined with thermal cyclic loads has been developed and demonstrated. Degradation effects resulting from long term environmental exposure and thermo-mechanical cyclic loads are considered in the simulation process. A unified time-stress dependent multi-factor interaction equation model developed at NASA Lewis Research Center has been used to account for the degradation of material properties caused by cyclic and aging loads. Effect of variation in the thermal cyclic load amplitude on a quasi-symmetric graphite/epoxy laminate has been studied with respect to the impending failure modes. The results show that, for the laminate under consideration, the fatigue life under combined mechanical and low thermal amplitude cyclic loads is higher than that due to mechanical loads only. However, as the thermal amplitude increases, the life also decreases. The failure mode changes from tensile under mechanical loads only to the compressive and shear at high mechanical and thermal loads. Also, implementation of the developed methodology in the design process has been discussed.
The response of composite laminates to long-term, cyclic loading conditions is dependent on mode and level of loading, material system, geometry, and laminate stacking sequence. An overview of basic damage mechanisms in notched laminates is presented. The relationships between damage and long-term response, specifically changes in residual tensile and compressive strength and life, are discussed for several composite systems with different matrix materials subjected to reversed cyclic loading.
A test method to measure the response of composite materials under reversed cyclic loads is described. The method approximates the long-term response of a component by permitting the composite specimen to respond to the imposed loads and fail in an unconstrained mode rather than in a constrained mode. The method has been successfully used for the reversed cyclic loading of unnotched and notched graphite/epoxy and graphite/PEEK laminates of various stacking sequences. Included in the paper are monotonic tensile and compressive stiffness and strength data at several points in the fatigue lifetime, and damage development information obtained via X-ray radiography for quasi-isotropic T300/5208 and AS4/PEEK laminates with unloaded circular holes.
The cyclic loads tests performed on the 30-in. segments of the DM-9 (Development Motor-9) configuration solid rocket outer boot ring are described. The tests found that the effect of the cyclic loadings on the structural integrity of the outer boot ring was negligible. The results are compared with a hand analysis of the strength of a 30-in. outer boot ring segment. Several phenomena of engineering interest are also described.
In this paper, the Barton–Bandis model for rock joints is extended to cyclic loading conditions, without any new material parameter. Also developed herein is an implicit solution algorithm for the extended Barton–Bandis model, which can also be used for the original Barton–Bandis model for which an implicit algorithm has been unavailable. To this end, we first cast the Barton–Bandis model into an incremental elasto-plastic framework, deriving an expression for the elastic shear stiffness being consistent with the original model formulation. We then extend the model formulation to cyclic loading conditions, incorporating the dependence of shear stress and dilation on the joint position and the shearing direction. The extension is achieved by introducing a few state-dependent variables which can be calculated with the existing material parameters. For robust and accurate utilization of the model, we also develop an implicit algorithm based on return mapping, which is unconditionally stable and guarantees the satisfaction of the strength criterion. We verify that the proposed model formulation and algorithm produce virtually the same results as the original Barton–Bandis model under monotonic shearing conditions. Here, we then validate the extended Barton–Bandis model against experimental data on natural rock joints under cycling loading conditions. The present work thus enables the Barton–Bandis model, which has been exceptionally popular in research and practice, to be applicable to a wider range of problems in rock mechanics and rock engineering.
Based on the basic and essential features of the elastic-plastic response of the AS4/PEEK thermoplastic composite subjected to off-axis cyclic loadings, a simple rate-independent constitutive model is proposed to describe the orthotropic material behavior for cyclic loadings. A one-parameter memory surface is introduced to distinguish the virgin deformation and the subsequent deformation process and to characterize the loading range effect. Cyclic softening is characterized by the change of generalized plastic modulus. By the vanishing yield surface assumption, a yield criterion is not needed and it is not necessary to consider loading and unloading separately. The model is compared with experimental results and good agreement is obtained.
Experimental results from monotonic and cyclic tension tests on six different 6061 boron-aluminum laminates show that the strength of fiber dominated laminates is decreased and the strength of matrix dominated laminates is increased by T6 heat treatment. Cyrogenic exposure and cyclic loading are shown to have little influence on strength. Cyclic loading is also shown to produce small reductions in modulus for some laminates and some temper conditions. The results are discussed in light of expected metallurgical and residual stress changes due to temperature excursions and loading cycles.