Search NASA⌕ Search

SEARCH · Search NASA

Results for “DAMPING IN ROLL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Aerodynamic roll damping of a T-tail transport configuration

The aerodynamic roll damping and the yawing moment due to roll rate for a model of a T-tail transport with aft-mounted engines were measured by means of a small-amplitude forced-oscillation mechanism. The tests were made for Mach numbers between 0.21 and 0.80 over a range of angles of attack from about minus 4 deg to 22 deg. The basic configuration had positive damping in roll at low angles of attack with regions of low positive and negative damping for angles of attack above 8 deg to 10 deg. There was good agreement between the theoretical estimates of the roll damping for the wing alone and the experimental results at an angle of attack of 0 deg for Mach numbers of 0.60 and less. The T-tail configuration and the engine nacelles mounted aft on the fuselage did not significantly affect either the damping in roll or the yawing moment due to roll rate.

Boyden, R. P.↗
NASA NTRS1974

Subsonic roll-damping characteristics of a series of wings

The aerodynamic damping in roll of a series of wings has been investigated in the Langley high-speed 7- by 10-foot tunnel at Mach numbers ranging from 0.2 to 0.8 by use of a forced oscillatory-roll technique. Tests were conducted on wings of aspect ratio 6 with sweep angles of 25, 35, and 45 deg and on 35 deg swept wings of aspect ratios 4 and 5.

Boyden, R. P.↗
NASA NTRS1978

Subsonic roll damping of a model with swept-back and swept-forward wings

The aerodynamic roll damping and the yawing moment due to roll rate characteristics were investigated at subsonic speeds for a model with either sweptback or swept forward wings. The tests were made in the Langley high speed 7 by 10 foot tunnel for Mach numbers between 0.3 and 0.7. The configuration with a 60 deg sweptback wing had positive damping in roll up to the maximum test angle of attack of almost 20 deg. The 32 deg swept forward wing configuration had positive damping in roll at the lower angles of attack, but there was a decrease in damping and negative damping in roll was measured at the highest angles of attack.

Boyden, R. P.↗
NASA NTRS1973

Wind-tunnel roll-damping measurements of a winged space shuttle configuration in launch attitude

Ground-wind load studies were conducted on three model configurations to assess the importance of aeroelastic instabilities of erected space shuttle vehicles. Roll damping was measured on a fuselage-alone model, which had a D cross section, and a fuselage and tail surfaces in combination with either a clipped-delta wing or a low-sweep tapered wing as the primary lifting surface. The largest negative roll-damping coefficients were measured with the fuselage-alone configuration and were a function of wind azimuth. At the wind azimuths at which the wing-fuselage configuration was unstable, the negative roll-damping coefficients were a function of reduced frequency.

Hess, R. W.↗
NASA NTRS1975

Experimental pitch-, yaw-, and roll-damping characteristics of a shuttle orbiter at Mach number 8

Wind tunnel tests were conducted to measure the pitch-, yaw-, and roll-damping characteristics of a modified 089B shuttle orbiter. These tests were conducted for NASA-Langley at the von Karman Gas Dynamics Facility of the Arnold Engineering Development Center. Data were obtained utilizing the small amplitude forced-oscillation technique at angles of attack of -4.9 to 26.5 deg at Reynolds numbers, based on model length, of 1,180,000 to 4,820,000. The orbiter was dynamically stable in pitch, yaw, and roll, and the pitch derivatives were dependent on Reynolds number, while the roll derivatives were independent of Reynolds number.

Uselton, B. L.↗
NASA NTRS2011

Handling Qualities Evaluations of Low Complexity Model Reference Adaptive Controllers for Reduced Pitch and Roll Damping Scenarios

National Aeronautics and Space Administration (NASA) researchers have conducted a series of flight experiments designed to study the effects of varying levels of adaptive controller complexity on the performance and handling qualities of an aircraft under various simulated failure or damage conditions. A baseline, nonlinear dynamic inversion controller was augmented with three variations of a model reference adaptive control design. The simplest design consisted of a single adaptive parameter in each of the pitch and roll axes computed using a basic gradient-based update law. A second design was built upon the first by increasing the complexity of the update law. The third and most complex design added an additional adaptive parameter to each axis. Flight tests were conducted using NASA s Full-scale Advanced Systems Testbed, a highly modified F-18 aircraft that contains a research flight control system capable of housing advanced flight controls experiments. Each controller was evaluated against a suite of simulated failures and damage ranging from destabilization of the pitch and roll axes to significant coupling between the axes. Two pilots evaluated the three adaptive controllers as well as the non-adaptive baseline controller in a variety of dynamic maneuvers and precision flying tasks designed to uncover potential deficiencies in the handling qualities of the aircraft, and adverse interactions between the pilot and the adaptive controllers. The work was completed as part of the Integrated Resilient Aircraft Control Project under NASA s Aviation Safety Program.

Hanson, Curt↗
NASA NTRS2014

Roll Damping Derivatives from Generalized Lifting-Surface Theory and Wind Tunnel Forced-Oscillation Tests

Improving aerodynamic models for adverse loss-of-control conditions in flight is an area being researched under the NASA Aviation Safety Program. Aerodynamic models appropriate for loss of control conditions require a more general mathematical representation to predict nonlinear unsteady behaviors. As more general aerodynamic models are studied that include nonlinear higher order effects, the possibility of measurements that confound aerodynamic and structural responses are probable. In this study an initial step is taken to look at including structural flexibility in analysis of rigid-body forced-oscillation testing that accounts for dynamic rig, sting and balance flexibility. Because of the significant testing required and associated costs in a general study, it makes sense to capitalize on low cost analytical methods where possible, especially where structural flexibility can be accounted for by a low cost method. This paper provides an initial look at using linear lifting surface theory applied to rigid-body aircraft roll forced-oscillation tests.

Pototzky, Anthony S↗
NASA NTRS1986

Wind-tunnel investigation of the flight characteristics of a canard general-aviation airplane configuration

A 0.36-scale model of a canard general-aviation airplane with a single pusher propeller and winglets was tested in the Langley 30- by 60-Foot Wind Tunnel to determine the static and dynamic stability and control and free-flight behavior of the configuration. Model variables made testing of the model possible with the canard in high and low positions, with increased winglet area, with outboard wing leading-edge droop, with fuselage-mounted vertical fin and rudder, with enlarged rudders, with dual deflecting rudders, and with ailerons mounted closer to the wing tips. The basic model exhibited generally good longitudinal and lateral stability and control characteristics. The removal of an outboard leading-edge droop degraded roll damping and produced lightly damped roll (wing rock) oscillations. In general, the model exhibited very stable dihedral effect but weak directional stability. Rudder and aileron control power were sufficiently adequate for control of most flight conditions, but appeared to be relatively weak for maneuvering compared with those of more conventionally configured models.

Satran, D. R.↗
NASA NTRS1951

A Flight Investigation of the Damping in Roll and Rolling Effectiveness Including Aeroelastic Effects of Rocket Propelled Missile Models Having Cruciform, Triangular, Interdigitated Wings and Tails

The damping in roll and rolling effectiveness of two models of a missile having cruciform, triangular, interdigitated wings and tails have been determined through a Mach number range of 0.8 to 1.8 by utilizing rocket-propelled test vehicles. Results indicate that the damping in roll was relatively constant over the Mach umber range investigated. The rolling effectiveness was essentially constant at low supersonic speeds and increased with increasing mach numbers in excess of 1.4 over the Mach number range investigated. Aeroelastic effects increase the rolling-effectiveness parameters pb/2V divided by delta and decrease both the rolling-moment coefficient due to wing deflection and the damping-in-roll coefficient.

Russell N Hopko↗
NASA NTRS1953

Rocket-Model Measurements of Zero-Lift Damping in Roll of the Bell MX-776 Missile at Mach Numbers from 0.6 to 1.56

The zero-lift damping in roll of the Bell MX-776 missile has been measured by a sting-mounted rocket-model technique at Mach numbers from 0.6 to 1.56. The damping-in-roll data, in general, show no unusual variation with Mach number. Aileron rolling-moment effectiveness derived from these data and previously obtained rolling-effectiveness data appear reasonable,

Bland, William N., Jr.↗
NASA NTRS1978

Transonic static and dynamic stability characteristics of a finned projectile configuration

Static and dynamic stability tests were made of a finned projectile configuration with the aft-mounted fins arranged in a cruciform pattern. The tests were made at free stream Mach numbers of 0.7, 0.9, 1.1, and 1.2 in the Langley 8-foot transonic pressure tunnel. Some of the parameters measured during the tests were lift, drag, pitching moment, pitch damping, and roll damping. Configurations tested included the body with undeflected fins, the body with various fin deflections for control, and the body with fins removed. Theoretical estimates of the stability derivatives were made for the fins on configuration.

Boyden, R. P.↗
NASA NTRS1950

Theoretical lift and damping in roll at supersonic speeds of thin sweptback tapered wings with streamwise tips, subsonic leading edges, and supersonic trailing edges

On the basis of linearized supersonic-flow theory, generalized equations were derived and calculations made for the lift and damping in roll of a limited series of thin sweptback tapered wings. Results are applicable to wings with streamwise tips and for a range of supersonic speeds for which the wing is wholly contained between the Mach cones springing from the wing apex and from the trailing edge of the root section. A further limitation is that the tip Mach lines may not intersect on the wing. For the portion of the wing external to the Mach cones springing from the leading edge of the wing tips, the pressure distributions for lift and roll previously obtained for the triangular wing are valid. For the portion of the wing contained within the wing-tip Mach cones a satisfactory approximation to the exact pressure distribution was obtained by application of a point-source-distribution method developed in NACA-TN-1382. A series of design curves are presented which permit rapid estimation of the lift-curve slope and damping-in-roll derivative for given values of aspect ratio, taper ratio, Mach number, and leading-edge sweep. (author)

Malvestuto, Frank S , Jr↗
NASA NTRS1932

Effect of length of Handley Page tip slots on the lateral-stability factor, damping in roll

Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested.

Weick, Fred E↗
NASA NTRS1985

Theory of wing rock

Wing rock is one type of lateral-directional instabilities at high angles of attack. To predict wing rock characteristics and to design airplanes to avoid wing rock, parameters affecting wing rock characteristics must be known. A new nonlinear aerodynamic model is developed to investigate the main aerodynamic nonlinearities causing wing rock. In the present theory, the Beecham-Titchener asymptotic method is used to derive expressions for the limit-cycle amplitude and frequency of wing rock from nonlinear flight dynamics equations. The resulting expressions are capable of explaining the existence of wing rock for all types of aircraft. Wing rock is developed by negative or weakly positive roll damping, and sustained by nonlinear aerodynamic roll damping. Good agreement between theoretical and experimental results is obtained.

Hsu, C.-H.↗
NASA NTRS1984

Theory of wing rock

A theory is developed for predicting wing rock characteristics. From available data, it can be concluded that wing rock is triggered by flow asymmetries, developed by negative or weakly positive roll damping, and sustained by nonlinear aerodynamic roll damping. A new nonlinear aerodynamic model that includes all essential aerodynamic nonlinearities is developed. The Beecham-Titchener method is applied to obtain approximate analytic solutions for the amplitude and frequency of the limit cycle based on the three degree-of-freedom equations of motion. An iterative scheme is developed to calculate the average aerodynamic derivatives and dynamic characteristics at limit cycle conditions. Good agreement between theoretical and experimental results is obtained.

Hsu, C. H.↗