Search NASA⌕ Search

SEARCH · Search NASA

Results for “DME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Unsteady deflagration speed of an auto-ignitive dimethyl-ether (DME)/air mixture at stratified conditions

The propagation speed of an auto-ignitive dimethyl-ether (DME)/air mixture at elevated pressures and subjected to monochromatic temperature oscillations is numerically evaluated in a one-dimensional statistically stationary configuration using fully resolved numerical simulations with reduced kinetics and transport. Two sets of conditions with temperatures within and slightly above the negative temperature coefficient (NTC) regime are simulated to investigate the fundamental aspects of auto-ignition and flame propagation along with the transition from auto-ignitive deflagration to spontaneous propagation regimes under thermal stratification. Contrary to the standard laminar flame speed, the steady propagation speed of an auto-ignitive front is observed to scale proportionally to its level of upstream reactivity. It is shown that this interdependence is primarily influenced by the characteristic residence time and the homogeneous auto-ignition delay. Furthermore, the unsteady reaction front in either of the two cases responds distinctly to the imposed stratification. Specifically, the results in both cases show that the dynamic flame response depends on the mean temperature at the flame base Tb and the time-scale of thermal stratification. It is also found that, based on Tb and the propensity of the mixture to two-stage chemistry, the instantaneous peak propagation speed and the overall time taken to achieve that speed differs considerably. A displacement speed analysis is carried out to elucidate the underlying combustion modes that are responsible for such a variation in flame response.

Energy & Fuels↗

Fluid age-based analysis of a lifted turbulent DME jet flame DNS [Residence Time-Based Analysis of a Lifted Turbulent DME Jet Flame]

The link between the distribution of fluid residence time and the distribution of reactive scalars is analysed using Direct Numerical Simulation data. Information about the reactive scalar distribution is needed in order to model the reaction terms that appear in Large Eddy and Reynolds-Averaged simulations of turbulent reacting flows. The lifted flame is simulated taking account of multi-step chemistry for dimethyl-ether fuel and differential diffusion. Due to autoignition and flame propagation, the reaction progress increases with residence time. The variation of fluid residence time is evaluated by solving an Eulerian transport equation for the fluid age. The fluid age is a passive scalar with a spatially-uniform source term, meaning that its moments and dissipation rates in turbulent flows can be modelled using closures already established for conserved scalars such as mixture fraction. In combination with the mixture fraction, the fluid age serves as a useful mapping variable to distinguish younger less-reacted fluid near the inlet from older more-reacted fluid downstream. The local fluctuations of mixture fraction and fluid age have strong negative correlation and, building upon established presumed-pdf models for mixture fraction, this feature can be used to construct an accurate presumed-pdf model for the joint mixture fraction/fluid age pdf. It is demonstrated that the double-conditional first-order moment closure combined with the proposed presumed model for the joint pdf of mixture fraction and fluid age gives accurate predictions for unconditional reaction rates – both for pre-ignition radical species produced by low-temperature processes upstream of the flame base, and for major species that are produced at the flame front.

42 ENGINEERING↗

A Novel Catalytic Membrane Reactor for DME Synthesis from Renewable Resources

Production of liquid fuels or chemicals from CO 2 (captured from the air or flue gases) and renewable hydrogen presents a new approach to producing clean fuels domestically. While significant progress has been made in the area of renewable electricity generation from solar and wind, a large gap remains with respect to the production of renewable liquid fuels/chemicals. Other processes for producing liquid fuels/chemicals from renewable electricity are constrained by thermodynamic limitations, making them prohibitively expensive and impractical. The team is overcoming these limitations and developing catalytic membrane reactor processes with high yields and low energy penalties. Supported by the Advanced Research Projects Agency-Energy (ARPA-E) of the US Department of Energy (DOE), GTI Energy and partners have been developing a technology for the production of renewable dimethyl ether (DME) from carbon dioxide (CO 2 ) and renewable hydrogen (H 2 ) using a novel catalytic membrane reactor and demonstration of this system at a scale of 1 kg/day. DME is a clean-burning, non-toxic fuel with a high cetane value (55-60), making it an excellent diesel alternative. DME can be stored as a liquid under moderate pressure, eliminating the need for the high-pressure containers used for CNG or cryogenics, as in the case of LNG. DME is also approved as a renewable fuel under the U.S. Environmental Protection Agency’s Renewable Fuels Standard (RFS), making it eligible for Renewable Identification Numbers (RINs) credits. By producing DME through the catalytic conversion of captured CO 2 and renewable H 2 , this process will produce renewable liquid transportation fuel and a means of large-scale utilization of captured CO 2 . In the DME synthesis process, CO 2 and H 2 are fed to a hollow fiber catalytic membrane reactor at 300-600 psig that contains a bi-functional catalyst that combines two reactions, methanol synthesis (CO 2 + 3H 2 → CH 3 OH + H 2 O) and methanol dehydration (2CH 3 OH → CH 3 OCH 3 + H 2 O), into a one-step process to produce DME. The bifunctional catalyst converts methanol to DME, enabling higher overall CO 2 conversion. A Cu/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalyst is used for methanol synthesis and is coupled with a zeolite catalyst H-ZSM-5 for dehydration. This one-step process intensifies a process that would otherwise require multiple reaction steps. However, combining these two reactions results in increased water production which inhibits catalytic activity. Here, the Na + -gated, water-transport membrane (Science, vol. 367, pp. 667, 2020), removes water in situ, shifting the thermodynamic equilibrium towards product formation while decreasing kinetic inhibition from water adsorption onto the catalyst surface. The Na + gated, water-transport nanochannel membrane showed H 2 O/CO 2 selectivity of 560 at 250 °C and 300 psig for H 2 O/CO 2 /CO/H 2 /MeOH gas mixtures. The selectivities of H 2 O/H 2 , H 2 O/CO, and H 2 O/MeOH were 190, 170, and 80, respectively. In a laboratory-scale membrane reactor, DME synthesis testing using this membrane, a DME production rate of 440 g DME /kg cat /h was achieved at 260 °C and 550 psig. Compared to the packed bed reactor, the CO 2 conversion and DME production rate in the membrane reactor were 80% and three times higher, respectively. A prototype test system (1 kg/day) was designed, constructed, and tested. A DME production rate of 1.31 kg/day and a DME productivity of 360 g/h/kg were achieved in the prototype membrane reactor. Good stability was demonstrated during 150-h continuous operation and multiple startups/shutdowns tests.

10 SYNTHETIC FUELS↗

Ignition delay times of NH 3 /DME blends at high pressure and low DME fraction: RCM experiments and simulations

Here, autoignition delay times of ammonia/dimethyl ether (NH 3 /DME) mixtures were measured in a rapid compression machine with DME fractions of 0, 2 and 5 and 100% in the fuel. The measurements were performed at equivalence ratios $\varphi$= 0.5, 1.0 and 2.0 and pressures in the range 10–70 bar; depending on the fuel composition, the temperatures after compression varied from 610 K to 1180 K. Admixture of DME is seen to have a dramatic effect on the ignition delay time, effectively shifting the curves of ignition delay vs. temperature to lower temperatures, up to ~250 K compared to pure ammonia. Two-stage ignition is observed at $\varphi$= 1.0 and 2.0 with 2% and 5% DME in the fuel, despite the pressure being higher than that at which pure DME shows two-stage ignition. At $\varphi$= 0.5, a reproducible pre-ignition pressure rise is observed for both DME fractions, which is not observed in the pure fuel components. A novel NH 3 /DME mechanism was developed, including modifications in the NH 3 subset and addition of the NH 2 + CH 3 OCH 3 reaction, with rate coefficients calculated from ab initio theory. Simulations faithfully reproduce the observed pre- ignition pressure rise. While the mechanism also exhibits two-stage ignition for NH 3 /DME mixtures, both qualitative and quantitative improvement is recommended. The overall ignition delay times for ammonia/DME mixtures are predicted well, generally being within 50% of the experimental values, although reduced performance is observed for pure ammonia at $\varphi$= 2.0. Simulating the ignition process, we observe that the DME is oxidized much more rapidly than ammonia. Analysis of the mechanism indicates that this ‘early DME oxidation’ generates reactive species that initiate the oxidation of ammonia, which in turn begins heat release that raises the temperature and accelerates the oxidation process towards ignition. The reaction path analysis shows that the low-temperature chain-branching reactions of DME are important in the early oxidation of the fuel, while the sensitivity analysis indicates that several reactions in the oxidation of DME, including cross reactions between DME and NH 3 species presented here, are critical to ignition, even at fractions of 2% DME in the fuel.

10 SYNTHETIC FUELS↗

Performance and Emissions of an SI Engine Fueled With DME-Propane Blends

Dimethyl Ether (DME) is an alternative fuel that can be produced renewably and has the potential for lower CO and NOx emissions than conventional petroleum-based fuels. Blending DME with another gaseous fuel such as propane, which has a lower knock tendency than gasoline, can allow this fuel to be leveraged on SI engines. In this study, the use of DME-propane blends on a spark ignition (SI) engine was studied via computer simulations in order to understand the impact on engine performance and emissions and to identify the knock limitations of using such fuel blends. A 2L Hyundai SI engine was modeled in GT Power and the model was validated by comparing it with computational fluid dynamics (CFD) simulation results. Starting from pure propane, DME was added incrementally until knock was observed in the engine. Results indicate that it is feasible to run propane with DME percentages up to 35% before severe knock impacts were observed. The BTE was higher, but the BSFC also increased for DME-propane blends as compared to gasoline. Here, an increase in NOx emissions was detected along with a significant decrease in CO emissions. CO 2 emissions declined for propane as compared to gasoline but increased with the addition of DME.

alternative fuels↗

NOx Reduction on a Transition Metal-free γ-Al2O3 Catalyst Using Dimethylether (DME)

NO2 and dimethylether (DME) adsorption as well as DME and NO2 coadsorption on a transition metal-free γ-alumina catalyst were investigated via in-situ transmission Fourier transform infrared spectroscopy (in-situ FTIR), residual gas analysis (RGA) and temperature programmed desorption (TPD) techniques. NO2 adsorption at room temperature leads to the formation of surface nitrates and nitrites. DME adsorption on the alumina surface at 300 K leads to molecularly adsorbed DME, molecularly adsorbed methanol and surface methoxides. Upon heating the DME-exposed alumina to 500-600 K the surface is dominated by methoxide groups. At higher temperatures methoxide groups are converted into formates. At T > 510 K formate decomposition takes place to form H2O(g) and CO(g). DME and NO2 coadsorption at 423 K do not indicate a significant reaction between DME and NO2. However, in similar experiments at 573 K, fast reaction occurs and the methoxides present at 573 K before the NO2 adsorption are converted into formates, simultaneously with the formation of isocyanates. Under these conditions, NCO can further be hydrolyzed into isocyanic acid or ammonia with the help of water which is generated during the formate formation, decomposition and/or NCO formation steps.

10 SYNTHETIC FUELS↗

Experimental Investigation of the Effect of Air-Handling and DME-Propane Blends on the Performance and Emissions of a 4-Cylinder CI Engine

Dimethyl ether (DME) is considered an excellent alternative to diesel because of its higher cetane number and lower carbon content. Additionally, DME can be blended with abundantly available propane with minimal modifications to the propane infrastructure. This paper focuses on an experimental investigation of the effect of air-handling i.e., boost pressure and exhaust gas recirculation (EGR), and DME-propane blends on the combustion and emissions performance of a light-duty, four-cylinder, compression ignition (CI) engine. Here, the boost pressure and EGR sweeps were carried out and showed that higher boost pressures resulted in increased brake thermal efficiencies (BTE) at the expense of higher NOx emissions which could be reduced by an increase in EGR. The fuel sweeps were carried out at 0, 15 and 25% propane (neat, 85% and 75% DME) with 0% and 25% EGR. The fuel sweeps indicated that the ignition delay (ID) increased and burn duration (BD) decreased monotonically when the blend increased to 25% propane/75% DME. The results suggest optimum engine performance with neat DME at 105 kPa boost pressure and 25% EGR with propane addition improving the BTE with negligible increase in emissions. Higher contents of Propane, up to 25%, did not affect the variability of combustion, with standard deviations of burn duration and peak cylinder pressures below 1% for all test cases.

air-handling↗

DME-Propane Ignition Delay Time Measurements at Mixing Controlled Compression Ignition Engine-Relevant Conditions

The blend of dimethyl ether (DME, CH 3 OCH 3 ) and propane (C 3 H 8 ) is a potentially renewable fuel mixture that has the potential to replace diesel in compression ignition engines. The combination can potentially reduce particulate and greenhouse gas emissions compared to a conventional diesel engine operating under similar conditions. However, detailed conceptual and simulation studies must be conducted before adopting a new fuel on a compression ignition engine. For these simulations, accurate chemical kinetic models are necessary. However, the validity of chemical kinetic mechanisms in the literature is unknown for mixing controlled compression ignition (MCCI) engine operating conditions. Hence, in this work, we studied the ignition of dimethyl ether (DME) and propane blends in a shock tube at MCCI engine conditions. Ignition delay time (IDT) data was collected behind the reflected shock for DME-propane mixtures for heavy-duty compression ignition (CI) engine parameters. Undiluted experiments spanning temperatures of 700 to 1100 K and pressures of 55 to 84 bar for various blends (100% CH 3 OCH 3 / 0% C 3 H 8, 100% C 3 H 8 / 0% CH 3 OCH 3 , 60% CH 3 OCH 3 / 40% C 3 H 8 ) of DME and propane were combusted in synthetic air (21% O 2 / 79% N 2 ). Some experiments were conducted at higher pressures (90-120 bar) to understand model performance at these conditions. Comparisons of IDT were made with the predictions of recent chemical kinetic mechanisms for DME-propane mixture, including the Aramco3.0, NUIG, and Dames et al. mechanisms. All mechanisms overpredicted IDT compared to experimental values. Sensitivity analysis was conducted with Dames et al. model, and critical reactions sensitive to IDT of DME-propane mixture near 100 bar are outlined.

Mohammed, Zuhayr Pasha↗

Magnetic fields and dense chromospheres in dMe stars

The hypothesis is investigated that dense chromospheres of dMe stars are heated by dissipation of hydromagnetic waves which may be generated in active regions where the nonspot magnetic field strength can be as large as 5 to 10 kG. It is proposed that dMe stars are a set of magnetic stars on the lower main sequence which have strong fields generated by dynamo action in deep convective envelopes, while dM stars are nonmagnetic or weakly magnetic stars having no starspots on their surfaces. The combination of magnetic fields and dense chromospheres in dMe stars is shown to provide consistent evidence for several conclusions, including: (1) the dMe stars which are most likely to be flare stars are those with hydrogen emission lines and (2) propagation of flare-initiated coronal waves can trigger sympathetic stellar flares. It is suggested that grain formation occurs in starspots of dMe stars and that such grains in a circumstellar shell are responsible for the systematic IR excesses of dMe stars relative to dM stars.

Mullan, D. J.↗

Flame stabilization in DME spray flames under engine-relevant conditions characterized by OH* chemiluminescence and formaldehyde laser-induced fluorescence

The transient and quasi-steady flame structures of Dimethyl Ether (DME) fuel sprays, produced by a single-hole injector (Spray D), were investigated using Planar Laser-Induced Fluorescence (PLIF) and chemiluminescence imaging in a constant-volume chamber under Engine Combustion Network (ECN) Spray A conditions (900 K ambient temperature, 60 bar ambient pressure, 1500 bar injection pressure, and 22.8 kg/m 3 ambient density). Low-temperature chemical reaction zones were visualized using formaldehyde (CH 2 O) PLIF with 355 nm excitation, while high-temperature flame regions were captured via chemiluminescence imaging of excited-state hydroxyl radicals (OH*). Both transient and quasi-steady flame structures clearly show the transition from CH 2 O to OH*, highlighting the progression from low- to high-temperature combustion, while the position of the flame is displaced for DME compared to reference hydrocarbon n-dodecane. Homogeneous reactor calculations with detailed chemistry and using adiabatic mixing for initial temperature show that CH 2 O peaks are significantly higher for DME at the same equivalence ratio, with a higher heat-release during the cool-flame regime with respect to the fuel heating value. Thus, the cool-flame dynamic as a precursor to high-temperature combustion and flame stabilization exhibit distinct behavior for DME relative to conventional hydrocarbons, and these phenomena are effectively resolved through the soot-free nature of DME and the high-speed, time-resolved diagnostics.

CH2O laser-induced fluorescence↗

Evaluation of the Performance and Exhaust Emissions of a 4 Cylinder CI Engine Operating With Dimethyl Ether (DME) and Propane Blends

In response to stringent emissions regulations and the need for higher efficiency engines, the utilization of DME and propane fuel blends in compression ignition (CI) engines has gained interest in the automotive industry. In this study, a range of DME-propane blends are explored in a CI combustion strategy at high injection pressures. A GT-Power model of a 2.2 L Hyundai CI engine was developed to facilitate evaluation of the impacts of variations of DME and propane blends at a light and medium engine speed-torque-load operating condition; specifically at 1500 rpm, 50 Nm and 2.84 bar brake mean effective pressure (BMEP); and 2000 rpm, 150 Nm, 8.53 bar BMEP speed-torque-load combination. Here, the GT-Power model was validated using Computational Fluid Dynamics (CFD) simulations. The results indicate that high diesel-like efficiencies can be achieved with a 100% DME mass substitution and up to 50% propane-DME blends could be implemented without a significant penalty on engine performance indicators. Significant brake specific nitrogen oxides (BSNOx) reductions were also observed along with reductions in carbon dioxide (CO2) and soot when leveraging these fuel blends.

computational fluid dynamics↗

Direct Numerical Simulations of Autoignition in Stratified Dimethyl-ether (DME)/Air Turbulent Mixtures

In our paper, two- and three-dimensional direct numerical simulations (DNS) of autoignition phenomena in stratified dimethyl-ether (DME)/air turbulent mixtures are performed. A reduced DME oxidation mechanism, which was obtained using rigorous mathematical reduction and stiffness removal procedure from a detailed DME mechanism with 55 species, is used in the present DNS. The reduced DME mechanism consists of 30 chemical species. This study investigates the fundamental aspects of turbulence-mixing-autoignition interaction occurring in homogeneous charge compression ignition (HCCI) engine environments. A homogeneous isotropic turbulence spectrum is used to initialize the velocity field in the domain. Moreover, the computational configuration corresponds to a constant volume combustion vessel with inert mass source terms added to the governing equations to mimic the pressure rise due to piston motion, as present in practical engines. DME autoignition is found to be a complex three-staged process; each stage corresponds to a distinct chemical kinetic pathway. The distinct role of turbulence and reaction in generating scalar gradients and hence promoting molecular transport processes are investigated. Then, by applying numerical diagnostic techniques, the different heat release modes present in the igniting mixture are identified. In particular, the contribution of homogeneous autoignition, spontaneous ignition front propagation, and premixed deflagration towards the total heat release are quantified.

33 ADVANCED PROPULSION SYSTEMS↗

DME-to-Propane Mixture Effects on a Light Duty Compression Ignition Engine

Fuels that can be produced in a sustainable manner are of high interest because they can provide an essential step toward net zero emissions vehicles. This study examines the combustion of two such fuels, Dimethyl Ether (DME) and propane, in a compression ignition, 4-cylinder, 2.2L engine running with mixtures of DME-to-Propane ranging of 100%-0%, 85%-15%, 75%-25%, and 65%-35% by weight. Testing was conducted at 2000rpm - 100Nm, an important representative point in the FTP certification cycle. For each fuel mixture, conditions tested include sweeps of boost, EGR and injection pressure. Here, tests are mainly conducted at a constant combustion timing with CA10 of -1 deg with respect to TDC, with an engine controller combustion feedback system based on in-cylinder sampling of pressure. Trends of NOx, HC, and CO are similar for the range of DME-to-propane, from 100%-0% to 75%-25%. Boost and injection pressures had the most notable impact on the heat release traces. Higher boost, from stoichiometric to lean resulted in approximately a 3-5% increase on cycle efficiency. Fuel injection pressures resulted in about 1% gain per 200bar. Results also illustrated that EGR is effective in reducing NOx but causes notable degradation of cycle efficiency. The emissions for DME-propane mixtures with 65%-35% had a different trend, with CO and HC exceeding the runs with lower propane content by 2 to 3-fold. As propane content increases, the pressure rise rates become higher, and with 65%-35% mixtures, rates easily exceed 12bar/deg. The increased rise rates correlate with early injection timings but the rates can be reduced, with higher boost and lower injection pressures. The result of the approach, however, leads to lower thermal efficiencies, decreasing efficiency by over 5% between neat DME and the highest propane ratios.

Combustion and combustion processes↗

Addition of phenylacetylene and camphor to the complex [(dpp-bian)Eu(dme){sub 2}] (dpp-bian is the 1,2-bis[(2,6-diisopropylphenyl)imino]acenaphthene dianion)

The reduction of 1,2-bis[(2,6-diisopropylphenyl)imino]acenaphthene (dpp-bian) with an excess of europium metal in 1,2-dimethoxyethane (dme) produces a divalent europium complex with the dpp-bian dianion, [(dpp-bian)Eu(dme){sub 2}] (1). The reactions of 1 with phenyl-acetylene and camphor proceed via protonation of the diimine ligand to form the monomeric amido-amino complexes of divalent europium — [H(dpp-bian)Eu(C≡CPh)(dme){sub 2}] (2) and [H(dpp-bian)Eu(camphor)(dme){sub 2}] (3), respectively. Compounds 2 and 3 were characterized by IR spectroscopy and elemental analysis. Their molecular structures were determined by X-ray diffraction. Compounds 2 and 3 were shown to be monomeric seven-coordinate europium(II) complexes with terminal phenylethynyl and enol ligands, respectively. According to the IR spectroscopic data, the terminal ligands in complexes 2 and 3 undergo tautomerization involving backward proton transfer from the amido-amino ligand to the substrate. The magnetic moment of compound 2 (8.03 μB) remains constant in the temperature range of 4—300 К and confirms the presence of divalent europium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced catalytic performance of Zr modified CuO/ZnO/Al 2 O 3 catalyst for methanol and DME synthesis via CO 2 hydrogenation

Zirconium (Zr) modified CuO/ZnO/Al 2 O 3 (CZA) catalysts with different aluminum (Al) and Zr contents were synthesized by the co-precipitation method. The synthesized CuO/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalysts were comprehensively characterized and studied for methanol synthesis via CO 2 hydrogenation. The CZZA catalyst showed the highest methanol yield of 12.4 % at 220 °C and 2.76 MPa with an optimized catalyst composition of Cu/Zn/Zr/Al (atomic ratio) at 4:2:1:0.5. The CZZA catalyst showed better activity than that of the CZA catalyst and a superior stability for methanol synthesis. There was no decrease in the BET surface area and very little coke formation for the spent CZZA catalyst, after 300 h of methanol synthesis. Bifunctional catalysts, composed of CZZA and HZSM-5, were investigated for dimethyl ether (DME) synthesis directly from CO 2 hydrogenation, and a maximum DME yield of 18.3 % was obtained at a reaction temperature of 240 °C and a pressure of 2.76 MPa. The stability of the bifunctional CZZA and HZSM-5 catalyst during the DME synthesis also significantly improved, as compared to that of the CZA and HZSM-5. A significant decrease in the BET surface area and an increase in coking on the spent CZZA catalyst were observed after 100 h of DME synthesis, indicating a detrimental effect on CZZA stability when a HZSM-5 catalyst was present. The changes in structural properties (e.g., BET surface area and crystallinity) and coking for HZSM-5 could be responsible for the deactivation of the bifunctional catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗