Search NASA⌕ Search

SEARCH · Search NASA

Results for “Data Injection attacks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

The prediction of viscous hypersonic flows about complex configurations using an upwind parabolized Navier-Stokes code

A three-dimensional parabolized Navier-Stokes computer code which employs an upwind algorithm is used to conduct a numerical study of an advanced maneuvering reentry vehicle configuration. Comparisons between numerical solutions and experimental data are presented for surface pressure, wall heat flux, and overall forces and moments. The effects of angle of attack, angle of yaw, and surface mass injection are investigated. Good agreement is observed between the calculated and measured data. The results of this investigation demonstrate the accuracy and efficiency of an upwind scheme in predicting the hypersonic flow field characteristics about a complex configuration.

Narain, J. P.↗
NASA NTRS1971

A study of boundary layer transition on outgassing cones in hypersonic flow

Surface heat-transfer rates and pressures were measured at hypersonic speeds on sharp cones at zero angle of attack with and without gas injection. Using the non-injection results for reference data the effects on heating and transition location of surface roughness and injectant rate, distribution and composition were determined. The transition location was sensitive to the injectant distribution. The transition Reynolds numbers were significantly greater when the injectant distribution was constant than with a variable distribution. The measured heat-transfer distribution were also strongly dependent upon the injectant distribution. Transition Reynolds number results obtained during this program with a variable injectant distribution were correlated with a limited amount of data available for a degrading model tested in a different facility. Transitional data with constant injectant distribution were correlated with earlier results. An empirical correlation of heat-transfer reduction due to gas injection in turbulent flow was developed for both distributions tested. Several effects of mass addition on heating and transition, which have been earlier reported, were observed.

Stalmach, C. J., Jr.↗
NASA NTRS1982

Advancements in aerothermodynamics in support of the Galileo probe

The Galileo probe, scheduled for launch in 1985, will experience the most severe heating environment ever encountered for a planetary mission, and the probe design should be based on a reliable definition of the aerothermal environment during entry. Significant advances in numerical computations make possible the prediction of such complicated flowfields, which include the effects of massive ablation injection, radiative transfer, turbulence, shape change and small angle of attack. Also included is a discussion of modeling and data inputs for numerical computations as deduced from both experimental and analytical studies concerning: radiation, transport and thermodynamic properties; probe afterbody flowfield and heating conditions; and the role of ablator spallation.

Moss, J. N.↗
NASA NTRSDate not supplied

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles ( δ a ) to increase lift-to-drag ratio (R/J). Improvements in low speed R/J can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to δ a = 16° relative to the nominal configuration, δ a = 7.5°. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D . Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

High-Lift Common Research Model↗
NASA NTRSDate not supplied

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles to increase lift-to-drag ratio (L/D). Improvements in low speed L/D can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to an aileron deflected at 16° relative to the nominal configuration of 7.5° deflection. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D. Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

CRM-HL↗
NASA NTRS1990

In-flight flow visualization with pressure measurements at low speeds on the NASA F-18 high alpha research vehicle

In-flight results from surface and off-surface flow visualizations and from extensive pressure distributions document the vortical flow on the leading edge extensions (LEX) and forebody of the NASA F-18 high alpha research vehicle for low speeds and angles of attack up to 50 degs. Surface flow visualization data, obtained using the emitted fluid technique, were used to define separation lines and laminar separation bubbles. Off-surface flow visualization data, obtained by smoke injection, were used to document both the path of the vortex cores and the location of vortex core breakdown. The location of vortex core breakdown correlated well with the loss of suction pressure on the LEX and with the flow visualization results from ground facilities. Surface flow separation lines on the LEX and forebody corresponded well with the end of pressure recovery under the vortical flows. Correlation of the pressures with wind tunnel results show fair to good correlation.

Delfrate, John H.↗
NASA NTRS1990

In-flight flow visualization and pressure measurements at low speeds on the NASA F-18 high alpha research vehicle

Inflight results from surface and off surface flow visualizations and from extensive pressure distributions document the vortical flow on the leading edge extensions (LEXs) and forebody of the NASA F-18 high alpha research vehicle (HARV) for low speeds and angles of attack up to 50 deg. Surface flow visualization data, obtained using the emitted fluid technique, were used to define separation lines and laminar separation bubbles (LSB). Off surface flow visualization data, obtained by smoke injection, were used to document both the path of the vortex cores and the location of vortex core breakdown. The location of vortex core breakdown correlated well with the loss of suction pressure on the LEX and with the flow visualization results from ground facilities. Surface flow separation lines on the LEX and forebody corresponded well with the end of pressure recovery under the vortical flows. Correlation of the pressures with wind tunnel results show fair to good correlation.

John H Del Frate↗
NASA NTRS2006

Test Capability Enhancements to the NASA Langley 8-Foot High Temperature Tunnel

The NASA Langley 8-Foot High Temperature Tunnel produces true enthalpy environments simulating flight from Mach 4 to Mach 7, primarily for airbreathing propulsion and aerothermal/thermo-structural testing. Flow conditions are achieved through a methane-air heater and nozzles producing aerodynamic Mach numbers of 4, 5 or 7 and have exit diameters of 8 feet or 4.5 feet. The 12-ft long free-jet test section, housed inside a 26-ft vacuum sphere, accommodates large test articles. Recently, the facility underwent significant upgrades to support hydrocarbon fueled scramjet engine testing and to expand flight simulation capability. The upgrades were required to meet engine system development and flight clearance verification requirements originally defined by the joint NASA-Air Force X-43C Hypersonic Flight Demonstrator Project and now the Air Force X-51A Program. Enhancements to the 8-Ft. HTT were made in four areas: 1) hydrocarbon fuel delivery; 2) flight simulation capability; 3) controls and communication; and 4) data acquisition/processing. The upgrades include the addition of systems to supply ethylene and liquid JP-7 to test articles; a Mach 5 nozzle with dynamic pressure simulation capability up to 3200 psf, the addition of a real-time model angle-of-attack system; a new programmable logic controller sub-system to improve process controls and communication with model controls; the addition of MIL-STD-1553B and high speed data acquisition systems and a classified data processing environment. These additions represent a significant increase to the already unique test capability and flexibility of the facility, and complement the existing array of test support hardware such as a model injection system, radiant heaters, six-component force measurement system, and optical flow field visualization hardware. The new systems support complex test programs that require sophisticated test sequences and precise management of process fluids. Furthermore, the new systems, such as the real-time angle of attack system and the new programmable logic controller enhance the test efficiency of the facility. The motivation for the upgrades and the expanded capabilities is described here.

Harvin, S. F.↗
NASA NTRS1987

Development of computer models for correlating data of film cooling of nose cone under hypersonic flow

A 12.5 degree half cone with tangential slot injection at Mach 6.95 was studied to determine the heating rates to the surface of the body near and far downstream of the slot. The cone had a zero degree angle of attack. The heating rates were obtained using a computer program that was developed at NASA-Langley Research Center. The concentration of nitrogen from the slot into the boundary layer was also determined. The ratio of slot to freestream was varied to determine its effect on heating. The numerical heating rates were compared to other correlations obtained from experimental studies as well as theoretical laminar and turbulent results.

Sharpe, L., Jr.↗
NASA NTRS2000

Experimental Study of the Structure of a Wingtip Vortex

A complete look at the near-field development and subsequent role-up of a wingtip vortex from a NACA 0015 wing section is investigated. Two separate but equally important surveys of the vortex structure in the region adjacent to the wingtip and approximately one chord length downstream of the trailing edge are performed. The two surveys provide qualitative flow-visualization an quantitative velocity measurement data. The near-field development and subsequent role-up of the vortex structures is strongly influenced by the angle-of-attack and the end-cap treatment of the wing section. The velocity field near the wingtip of the NACA 0015 wing section was measured with a triple-sensor hot wire probe and compared to flow visualization images produced with titanium tetrachloride smoke injection and laser illumination. The flat end-cap results indicate the formation of multiple, relatively strong vortex structures as opposed to the formation of a single vortex produced with the round end-cap. The multiple vortices generated by the flat end-cap are seen to rotate around a common ce te in a helical pattern until they eventually merge into a single vortex. Compared to a non-dimensional loading parameter, the results of the velocity and flow visualization data shows a "jetlike" axial velocity profile for loading parameter values on the order of 0.1 and a "wakelike" profile for much lower loading parameter values.

Anderson, Elgin A.↗
NASA NTRS2006

Planar laser-induced fluorescence (PLIF) investigation of hypersonic flowfields in a Mach 10 wind tunnel

Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize four different hypersonic flowfields in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The four configurations were: (1) the wake flowfield of a fuselage-only X-33 lifting body, (2) flow over a flat plate containing a rectangular cavity, (3) flow over a 70deg blunted cone with a cylindrical afterbody, formerly studied by an AGARD working group, and (4) an Apollo-geometry entry capsule - relevant to the Crew Exploration Vehicle currently being developed by NASA. In all cases, NO was seeded into the flowfield through tubes inside or attached to the model sting and strut. PLIF was used to visualize the NO in the flowfield. In some cases pure NO was seeded into the flow while in other cases a 5% NO, 95% N2 mix was injected. Several parameters were varied including seeding method and location, seeding mass flow rate, model angle of attack and tunnel stagnation pressure, which varies the unit Reynolds number. The location of the laser sheet was as also varied to provide three dimensional flow information. Virtual Diagnostics Interface (ViDI) technology developed at NASA Langley was used to visualize the data sets in post processing. The measurements demonstrate some of the capabilities of the PLIF method for studying hypersonic flows.

Danehy, Paul M.↗
NASA NTRS2011

ALH84001: The Key to Unlocking Secrets About Mars-15 Years and Counting

From the December 27, 1984 discovery of ALH84001, and its subsequent identification as a sample of Mars in 1993, mystery and debate has surrounded the meteorite. With the realization that the ALH84001 sample was a orthopyroxenite and one of the oldest SNC meteorites (~4.09 Ga) available to study, important and critical information about the Martian hydrosphere and atmosphere along with the early history and evolution of the planet could be obtained by studying the unique carbonate globules (~3.9 Ga) in the sample. The initial work showed the carbonate globules were deposited within fractures and cracks in the host-orthopyroxene by low-temperature aqueous fluids. Ideas that the carbonates were formed at temperatures approaching 800oC were ruled out by later experiments. The 1996 announcement by McKay et al. that ALH84001 contained features which could be interpreted as having a biogenic origin generated considerable excitement and criticism. The NASA Administrator Dan Golden said the 1996 ALH84001 announcement saved NASA s Mars planetary exploration program and injected $6 billion dollars over five years into the scientific research and analysis efforts. All of the original four lines of evidence for possible biogenic features within ALH84001 offered by McKay et al. have withstood the test of time. Criticism has been directed at the interpretation of the 1996 analytical data. Research has expanded to other SNC meteorites. Despite the numerous attacks on the ideas, the debate continues after 15 years. The 2009 paper by Thomas-Keprta et al. on the origins of a suite of magnetites within the ALH84001 has offered strong arguments that some of the magnetites can only be formed by biogenic processes and not from thermal decomposition or shock events which happened to the meteorite. NASA s Astrobiology Institute was formed from the foundation laid by the ALH84001 hypothesis of finding life beyond the Earth. The strong astrobiology outreach programs have expanded because of the work done on the Martian meteorites. Despite the criticism on the biogenic-like features in ALH84001, the meteorite has opened a window into the early history of Mars. Clearly low-temperature fluids have left their signatures within the ALH84001 meteorite and subsequent cratering events on Mars have been recorded on observable features within the meteorite. The 15 years of detailed study on ALH84001 and its unique carbonate globules have clearly shown formational and secondary processes at work on Mars. The evidence for biogenic processes operating on early Mars along with ground water activity within the last 15% of the life of Mars offers clear evidence that another niche for life may be possible within our solar system. Now we need a well-documented Mars sample return mission.

Gibson, Everett K.↗
NASA NTRS2011

ALH84001: The Key to Unlocking Secrets About Mars-15 Years and Counting

From the December 27, 1984 discovery of ALH84001, and its subsequent identification as a sample of Mars in 1993, mystery and debate has surrounded the meteorite [1]. With the realization that the ALH84001 sample was a orthopyroxenite and one of the oldest SNC meteorites (approx.4.09 Ga) [2] available to study, important and critical information about the Martian hydrosphere and atmosphere along with the early history and evolution of the planet could be obtained by studying the unique carbonate globules (approx.3.9 Ga) in the sample [3]. The initial work showed the carbonate globules were deposited within fractures and cracks in the host-orthopyroxene by low-temperature aqueous fluids [4]. Ideas that the carbonates were formed at temperatures [5] approaching 800 C were ruled out by later experiments [6]. The 1996 announcement by McKay et al. [7] that ALH84001 contained features which could be interpreted as having a biogenic origin generated considerable excitement and criticism. The NASA Administrator Dan Golden said the 1996 ALH84001 announcement saved NASAs Mars planetary exploration program and injected $6 billion dollars over five years into the scientific research and analysis efforts [8]. All of the original four lines of evidence for possible biogenic features within ALH84001 offered by McKay et al. have withstood the test of time. Criticism has been directed at the interpretation of the 1996 analytical data. Research has expanded to other SNC meteorites. Despite the numerous attacks on the ideas, the debate continues after 15 years. The 2009 paper by Thomas-Keprta et al. [9] on the origins of a suite of magnetites within the ALH84001 has offered strong arguments that some of the magnetites can only be formed by biogenic processes and not from thermal decomposition or shock events which happened to the meteorite. NASA s Astrobiology Institute was formed from the foundation laid by the ALH84001 hypothesis of finding life beyond the Earth. The strong astrobiology outreach programs have expanded because of the work done on the Martian meteorites. De-spite the criticism on the biogenic-like features in ALH84001, the meteorite has opened a window into the early history of Mars. Clearly low-temperature fluids have left their signatures within the ALH84001 meteorite and subsequent cratering events on Mars have been recorded on observable features within the meteorite. The 15 years of detailed study on ALH84001 and its unique carbonate globules have clearly shown formational and secondary processes at work on Mars. Now we need a well-documented Mars sample return mission.

Gibson, Everett K.↗
NASA NTRS1984

Analysis of heat-transfer measurements from 2 AEDC wind tunnels on the Shuttle external tank

Previous aerodynamic heating tests have been conducted in the AEDC/VKF Supersonic Wind Tunnel (A) to aid in defining the design thermal environment for the space shuttle external tank. The quality of these data has been under discussion because of the effects of low tunnel enthalpy and slow model injection rates. Recently the AEDC/VKF Hypersonic Wind Tunnel (C) has been modified to provide a Mach 4 capability that has significantly higher tunnel enthalpy with more rapid model injection rates. Tests were conducted in Tunnel C at Mach 4 to obtain data on the external tank for comparison with Tunnel A results. Data were obtained on a 0.0175 scale model of the Space Shuttle Integrated Vehicle at Re/ft = 4 x 10 to the 6th power with the tunnel stagnation temperature varying from 740 to 1440 R. Model attitude varied from an angle of attack of -5 to 5 deg and an angle of sideslip of -3 to 3 deg. One set of data was obtained in Tunnel C at Re/ft = 6.9 x 10 to the 6th for comparison with flight data. Data comparisons between the two tunnels for numerous regions on the external tank are given.

Nutt, K. W.↗
NASA NTRS1975

Test evaluation of potential heat shield contamination of an Outer Planet Probe's atmospheric sampling system

An Outer Planets Probe which retains the charred heatshield during atmospheric descent must deploy a sampling tube through the heatshield to extract atmospheric samples for analysis. Once the sampling tube is deployed, the atmospheric samples ingested must be free of contaminant gases generated by the heatshield. Outgassing products such as methane and water vapor are present in planetary atmospheres and hence, ingestion of such species would result in gas analyzer measurement uncertainties. This paper evaluates the potential for, and design impact of, the extracted atmospheric samples being contaminated by heatshield outgassing products. Flight trajectory data for Jupiter, Saturn and Uranus entries are analyzed to define the conditions resulting in the greatest potential for outgassing products being ingested into the probe's sampling system. An experimental program is defined and described which simulates the key flow field features for a planetary flight in a ground-based test facility. The primary parameters varied in the test include: sampling tube length, injectant mass flow rate and angle of attack. Measured contaminant levels predict the critical sampling tube length for contamination avoidance. Thus, the study demonstrates the compatibility of a retained heatshield concept and high quality atmospheric trace species measurements.

Kessler, W. C.↗
NASA NTRS2016

Simulation of Sweep-Jet Flow Control, Single Jet and Full Vertical Tail

This work is a simulation technology demonstrator, of sweep jets used to suppress boundary layer separation and increase maximum achievable load coefficients. A sweep jet is a discrete Coanda jet that oscillates in the plane parallel to an aerodynamic surface. It injects mass and momentum in the approximate stream wise direction. It also generate turbulent eddies at the oscillation frequency, which are typically large relative to boundary layer turbulence, and which augmenting mixing across the boundary layer to attack flow separation. Simulations of a fluidic oscillator, the sweep jet emerging from the oscillator, and the suppression of boundary layer separation by an array of sweep jets are performed. Simulation results are compared to data from a dedicated CFD validation experiment of a single oscillator and its sweep jet, and from a study of a full-scale Boeing 757 vertical tail augmented with an array of sweep jets.2, 20 A critical step in the work is the development of realistic time-dependent sweep-jet in flow boundary conditions, derived from the results of the single-oscillator simulations, which create the sweep jets in the full-tail simulations. Simulations were performed using the Over flow CFD solver, with high-order spatial discretization and a range of turbulence modeling. Good results were obtained for all flows simulated, when suitable turbulence modeling was used.

flow control↗
NASA NTRS2016

Simulation of Sweep-Jet Flow Control, Single Jet and Full Vertical Tail

This work is a simulation technology demonstrator, of sweep jet flow control used to suppress boundary layer separation and increase the maximum achievable load coefficients. A sweep jet is a discrete Coanda jet that oscillates in the plane parallel to an aerodynamic surface. It injects mass and momentum in the approximate streamwise direction. It also generates turbulent eddies at the oscillation frequency, which are typically large relative to the scales of boundary layer turbulence, and which augment mixing across the boundary layer to attack flow separation. Simulations of a fluidic oscillator, the sweep jet emerging from a nozzle downstream of the oscillator, and an array of sweep jets which suppresses boundary layer separation are performed. Simulation results are compared to data from a dedicated validation experiment of a single oscillator and its sweep jet, and from a wind tunnel test of a full-scale Boeing 757 vertical tail augmented with an array of sweep jets. A critical step in the work is the development of realistic time-dependent sweep jet inflow boundary conditions, derived from the results of the single-oscillator simulations, which create the sweep jets in the full-tail simulations. Simulations were performed using the computational fluid dynamics (CFD) solver Overow, with high-order spatial discretization and a range of turbulence modeling. Good results were obtained for all flows simulated, when suitable turbulence modeling was used.

flow control↗
NASA NTRS1987

Separation control over an airfoil at high angles of attack by sound emanating from the surface

Active control by sound emanating from a narrow gap in the vicinity of the leading edge of a symmetrical airfoil is used to study the influence of sound on the pressure distribution and the wake at high angles of attack. The results from experiments conducted at a Reynolds number based on the chord of 35,000 show that, with injection of sound at twice the shedding frequency of the shear layer, the region of separation becomes drastically reduced. The shear layer is found to be very sensitive to sound excitation in the vicinity of the separation point. The excitation sufficiently alters the global circulation to cause an increase in lift and reduction in drag. Furthermore, experimental results describing stall and post-stall conditions compare well with the limited data available and indicate that stall is delayed by sound injection into the separated region.

Huang, L. S.↗