SEARCH · Search NASA

Results for “De-Orbit”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Design of an unmanned, reusable vehicle to de-orbit debris in Earth orbit

The space debris problem is becoming more important because as orbital missions increase, the amount of debris increases. It was the design team's objective to present alternative designs and a problem solution for a deorbiting vehicle that will alleviate the problem by reducing the amount of large debris in earth orbit. The design team was asked to design a reusable, unmanned vehicle to de-orbit debris in earth orbit. The design team will also construct a model to demonstrate the system configuration and key operating features. The alternative designs for the unmanned, reusable vehicle were developed in three stages: selection of project requirements and success criteria, formulation of a specification list, and the creation of alternatives that would satisfy the standards set forth by the design team and their sponsor. The design team selected a Chain and Bar Shot method for deorbiting debris in earth orbit. The De-orbiting Vehicle (DOV) uses the NASA Orbital Maneuvering Vehicle (OMV) as the propulsion and command modules with the deorbiting module attached to the front.

Aziz, Shahed↗

NASA NTRS1975

Time bases, discretes, and interrupts

The effort performed to assure proper flight program handling of time bases, discretes, and interrupts was discussed. The following time bases are used as key mission events: guidance reference release, liftoff, S-1B low level sensors dry, S-1B outboard engines cutoff, S-IVB cutoff, and S-IVB de-orbit DCS command. The five discrete outputs in the discrete output register were verified for proper setting. Each discrete input is honored in the proper time frame by forcing each discrete in the following intervals: before the discrete is enabled, after the discrete has been detected, and after the discrete has been disabled. As an assurance that an interrupt is honored only in the proper time frames, each interrupt was forced during the following intervals: prior to the specified enable time, after the interrupt has been honored, after the interrupt has been disabled.

Source record↗

NASA NTRS1975

Digital command system

The correct processing of the Digital Command System (DCS), which provides a limited real-time means of controlling specific flight program functions, was verified. The ability of the flight program to correctly read and process DCS commands was verified. Tests made by the flight program after reading the contents of the command decoder register to establish the validity of the received data were verified through the following: DCS mode command verification, DCS data command verification, DCS data validation, and DCS error message. The operation of the following DCS commands accepted and processed by the flight program was tested: time base update, navigation update, generalized switch selector, memory dump, terminate, execute generalized maneuver, return to nominal timeline, ECS water control valve logic inhibit, execute maneuver, execute alternate sequence, targeting load, ladder magnitude limit, S-IVB/IU de-orbit, compressed data dump, and remove inhibit on the extraction maneuver.

Source record↗

NASA NTRS1974

The Space Shuttle - Key considerations

Typical Space Shuttle flight operations, including launch/insertion, on-orbit operations, de-orbit, and ground turnaround, are summarized. The orbiter, main engine, and solid rocket boosters will be reusable. The Shuttle will be able to abort ascent and return the orbiter plus payload to the launch site if necessary. Mission capabilities include a 7-30 day duration, crew of 4-7 (with 1-4 payload specialists), and 14,500-29,500 kg payloads. Payload accommodations, including cabin, crew provisions, pointing and position stability, thermal constraints, electric power, communications, payload deployment and retrieval, contamination control, and kits for extended missions, are considered. The Thermal Protection System, utilizing pyrolized carbon and silica tiles, is described. The Space Shuttle Main Engine design and performance are considered and compared to those of the J-2 engine used on Saturn/Apollo missions.

Malkin, M. S.↗

NASA NTRS1975

On-orbit flight control algorithm description

Algorithms are presented for rotational and translational control of the space shuttle orbiter in the orbital mission phases, which are external tank separation, orbit insertion, on-orbit and de-orbit. The program provides a versatile control system structure while maintaining uniform communications with other programs, sensors, and control effectors by using an executive routine/functional subroutine format. Software functional requirements are described using block diagrams where feasible, and input--output tables, and the software implementation of each function is presented in equations and structured flow charts. Included are a glossary of all symbols used to define the requirements, and an appendix of supportive material.

Source record↗

NASA NTRS1977

OFT-1 reference flight profile. Deorbit through landing

Changes made in the de-orbiting through landing reference flight profile because of increases in Orbiter weight during entry and in the circular orbital attitude prior to deorbit are discussed. The rationale for the shaping of each phase is also presented.

Heath, D.↗

NASA NTRS1988

NASA Shuttle Training Aircraft flight simulation overview

The Shuttle Training Aircraft (STA) is a variable stability, variable control law flying simulator used by NASA/JSC to train astronauts in the final landing phase of a Space Shuttle Orbiter. A general outline is given for the STA flight simulation system. An overview is given of the software generation and verification process through the Advanced Validation System (AVAS). The flight test techniques for software verification will be reviewed and the process for releasing the software for flight training will be covered. The astronaut STA training syllabus is examined. Parameter matching with the Orbiter in the final approach phase of de-orbit and landing is briefly examined. Simulation performance will be assessed against flight data, performance measurement, and cue synchronization.

Justiz, Charles R.↗

NASA NTRS1990

Lunar orbiting microwave beam power system

A microwave beam power system using lunar orbiting solar powered satellite(s) and surface rectenna(s) was investigated as a possible energy source for the Moon's surface. The concept has the potential of reduced system mass by placing the power source in orbit. This can greatly reduce and/or eliminate the 14 day energy storage requirement of a lunar surface solar system. Also propellants required to de-orbit to the surface are greatly reduced. To determine the practicality of the concept and the most important factors, a zero-th order feasibility analysis was performed. Three different operational scenarios employing state of the art technology and forecasts for two different sets of advanced technologies were investigated. To reduce the complexity of the problem, satellite(s) were assumed in circular equatorial orbits around the Moon, supplying continuous power to a single equatorial base through a fixed horizontal rectenna on the surface. State of the art technology yielded specific masses greater than 2500 kg/kw, well above projections for surface systems. Using advanced technologies the specific masses are on the order of 100 kg/kw which is within the range of projections for surface nuclear (20 kg/kw) and solar systems (500 kg/kw). Further studies examining optimization of the scenarios, other technologies such as lasers transmitters and nuclear sources, and operational issues such as logistics, maintenance and support are being carried out to support the Space Exploration Initiative (SEI) to the Moon and Mars.

Fay, Edgar H.↗

NASA NTRS1988

Some tether applications with small launch vehicles

This paper describes four potentially useful tether applications that are best suited to or even limited to small launch vehicles and their payloads. The first application uses a Small Expendable-tether Deployment System (SEDS) to deploy a 20-40 km tether which transfers momentum from the spent final stage to its payload. This de-orbits the stage and boosts the payload. The other concepts are endo-atmospheric applications specific to various kinds of boosters. In one, a large helicopter gently recovers a reusable booster while it is descending by parachute. Another improves the performance of a small single-stage-to-orbit launch vehicle, by lifting it by helicopter to an altitude of about 3 kilometers before ignition. The last tows an air-breathing launch vehicle to high speed behind a supersonic aircraft, to eliminate any need for low-speed propulsion on the launch vehicle.

Carroll, Joseph A.↗

NASA NTRS1990

Lunar orbiting microwave beam power system

A microwave-beam power system using lunar orbiting solar-powered satellite(s) and surface rectenna(s) is investigated as a possible energy source for the moon's surface. The concept has the potential of achieving reduced system mass by placing the power source in orbit. This can greatly reduce and/or eliminate the 14-d energy storage requirement of a lunar surface solar system. Also, propellants required to de-orbit to the surface are greatly reduced. To determine the practicality of the concept and the most important factors, a zeroth-order feasibility analysis is performed. Three different operation scenarios employing state of the art technology and forecasts for two different sets of advanced technologies are investigated. To reduce the complexity of the problem, satellite(s) are assumed to be in circular equatorial orbits around the moon, supplying continuous power to a single equatorial base through a fixed horizontal rectenna on the surface. State of the art technology yields specific masses greater than 2500 kg/kw, well above projections for surface systems. The specific masses are on the order of 100 kg/kW using advanced technologies, which is within the range of projections for surface nuclear (20 kg/kW) and solar systems (500 kg/kW). Further studies examining optimization of the scenarios, other technologies, such as laser transmitters and nuclear sources, and operational issues, such as logistics, maintenance, and support, are being carried out to support the Space Exploration Initiative (SEI) to the moon and Mars.

Fay, Edgar H.↗

NASA NTRS1991

Users manual for the IMA program

The Impulsive Mission Analysis (IMA) computer program provides a user-friendly means of designing a complete Earth-orbital mission profile using an 80386-based microcomputer. The IMA program produces a trajectory summary, an output file for use by the new Simplex Computation of Optimum Orbital Trajectories (SCOOT) program, and several graphics, including ground tracks on a world map, altitude profiles, relative motion plots, and sunlight/communication timelines. The user can design missions using any combination of three basic types of mission segments: double co-eliptic rendezvous, payload delivery, and payload de-orbit/spacecraft recovery. Each mission segment is divided into one or more transfers, and each transfer is divided into one or more legs, each leg consisting of a coast arc followed by a burn arc.

Williams, D. F.↗

NASA NTRS1991

Assured crew return vehicle

A return vehicle is disclosed for use in returning a crew to Earth from low earth orbit in a safe and relatively cost effective manner. The return vehicle comprises a cylindrically-shaped crew compartment attached to the large diameter of a conical heat shield having a spherically rounded nose. On-board inertial navigation and cold gas control systems are used together with a de-orbit propulsion system to effect a landing near a preferred site on the surface of the Earth. State vectors and attitude data are loaded from the attached orbiting craft just prior to separation of the return vehicle.

Cerimele, Christopher J.↗

NASA NTRS1992

Aerobrake concepts for NTP systems study

Design concepts are described for landing large spacecraft masses on the Mars surface in support of manned missions with interplanetary transportation using Nuclear Thermal Propulsion (NTP). Included are the mission and systems analyses, trade studies and sensitivity analyses, design analyses, technology assessment, and derived requirements to support this concept. The mission phases include the Mars de-orbit, entry, terminal descent, and terminal touchdown. The study focuses primarily on Mars surface delivery from orbit after Mars orbit insertion using an NTP. The requirements associated with delivery of logistical supplies, habitats, and other equipment on minimum energy Earth to Mars transfers are also addressed in a preliminary fashion.

Cruz, Manuel I.↗

NASA NTRS1992

Support activities to maintain SUMS flight readiness

The Shuttle Upper Atmosphere Mass Spectrometer (SUMS), a component experiment of the NASA Orbital Experiments Program (OEX), was flown aboard the shuttle Columbia (OV102) mounted at the forward end of the nose landing gear well with an atmospheric gas inlet system fitted to the lower fuselage (chin panel) surface. The SUMS was designed to provide atmospheric data in flow regimes inaccessible prior to the development of the Space Transportation System (STS). The experiment mission operation began about one hour prior to shuttle de-orbit entry maneuver and continued until reaching 1.6 torr (about 86 km altitude). The SUMS mass spectrometer consists of the spare unit from the Viking mission to Mars. Bendix Aerospace under contract to NASA LaRC incorporated the Viking mass spectrometer, a microprocessor based logic card, a pressurized instrument case, and the University of Texas at Dallas provided a gas inlet system into a configuration suited to interface with the shuttle Columbia. The SUMS experiment underwent static and dynamic calibration as well as vacuum maintenance before and after STS 40 shuttle flight. The SUMS flew a total of 3 times on the space shuttle Columbia. Between flights the SUMS was maintained in flight ready status. The flight data has been analyzed by the NASA LaRC Aerothermodynamics Branch. Flight data spectrum plots and reports are presented in the Appendices to the Final Technical Report for NAS1-17399.

Wright, Willie↗

NASA NTRS1992

Support activities to maintain SUMS flight readiness, volume 2. Attachment A: Flight 61-C report

Wright, Willie↗

NASA NTRS1992

Support activities to maintain SUMS flight readiness, volume 3. Attachment B: Flight STS-35 report, section A

The Shuttle Upper Atmosphere Mass Spectrometer (SUMS), a component experiment of the NASA Orbital Experiments Program (OEX), was flown aboard the shuttle Columbia (OV102) mounted at the forward end of the nose landing gear well with an atmospheric gas inlet system fitted to the lower fuselage (chin panel) surface. The SUMS was designed to provide atmospheric data in flow regimes inaccessible prior to the development of the Space Transportation System (STS). The experiment mission operation begins about 1 hour prior to shuttle de-orbit entry maneuver and continues until reaching 1.6 torr (about 86 km altitude). The SUMS flew a total of three missions, 61C, STS-35, and STS-40. Between flights, the SUMS was maintained in flight ready status. The flight data has been analyzed by the NASA LaRC Aerothermodynamics Branch. Flight data spectrum plots and reports are presented in the Appendices to the Final Technical Report for NAS1-17399. This volume presents flight data for flight STS-35 in graphical format.

Wright, Willie↗

NASA NTRS1992

Support activities to maintain SUMS flight readiness, volume 4. Attachment B: Flight STS-35 report, section B

Wright, Willie↗

NASA NTRS1992

Support activities to maintain SUMS flight readiness, volume 5. Attachment B: Flight STS-35 report, section C

The Shuttle Upper Atmosphere Mass Spectrometer (SUMS), a component experiment of the NASA Orbital Experiments Program (OEX), was flown aboard the shuttle Columbia (OV102) mounted at the forward end of the nose landing gear well with an atmospheric gas inlet system fitted to the lower fuselage (chin panel) surface. The SUMS was designed to provide atmospheric data in flow regimes inaccessible prior to the development of the Space Transportation System (STS). The experiment mission operation begins about 1 hour prior to shuttle de-orbit entry maneuver and continues until reaching 1.6 torr (about 86 km altitude). The SUMS flew a total of three missions, 61C, STS-35, and STS-40. Between flights, the SUMS was maintained in flight ready status. The flight data has been analyzed by the NASA LaRC Aerothermodynamics Branch. Flight data spectrum plots and reports are presented in the Appendices to the Final Technical Report for NAS1-17399. This volume presents spectral graphs of the reentry of flight STS-35.

Wright, Willie↗