Search NASA⌕ Search

SEARCH · Search NASA

Results for “Deep Space Network (DSN) antennas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

A Study of Near to Far Fields of JPL Deep Space Network (DSN) Antennas for RFI Analysis

This paper addresses the issue of calculating the gain and power distribution of DSN antennas in the Fresnel (middle zone) and Fraunhofer (far zone) as a function of the distance from the DSN antenna and the off-boresight angle. Calculating the near and mid fields of DSN antennas are of interest in the receive mode where the transmitting signals from nearby flying objects such as helicopters and airplanes transmitting in the DSN frequency range, interfere with the operation of sensitive RF receiving system of the DSN antennas, and in the transmit mode where fields from high-powered DSN antennas interfere with receivers on nearby flying objects such as helicopters or other systems. Computing the exact fields of a large DSN antenna is, in general, a very complicated and arduous task. Even far-field calculations, which are less complicated compared to near and mid zone fields, take considerable computer time. These calculations become even more involved and time-consuming in very near field and back field regions. We provide two approaches for addressing the radio frequency interference (RFI) issue. In this paper, actual fields in mid and far zones are calculated using a relatively simple formulation that is accurate enough for the purposes of RFI analysis. In a future paper, we study and develop simple reference models that provide upper limit bounds or envelopes of the far field patterns as a function of the antenna diameter and frequency, which can be used for obtaining the field at any given point in space.

aperture antennas↗
NASA NTRS1989

Precision pointing compensation for DSN antennas with optical distance measuring sensors

The pointing control loops of Deep Space Network (DSN) antennas do not account for unmodeled deflections of the primary and secondary reflectors. As a result, structural distortions due to unpredictable environmental loads can result in uncompensated boresight shifts which degrade pointing accuracy. The design proposed here can provide real-time bias commands to the pointing control system to compensate for environmental effects on pointing performance. The bias commands can be computed in real time from optically measured deflections at a number of points on the primary and secondary reflectors. Computer simulations with a reduced-order finite-element model of a DSN antenna validate the concept and lead to a proposed design by which a ten-to-one reduction in pointing uncertainty can be achieved under nominal uncertainty conditions.

Scheid, R. E.↗
NASA NTRS1992

Wind-induced dynamics of the deep space network antennas

Accurate spacecraft tracking by the NASA Deep Space Network (DSN) antennas must be assured during changing weather conditions. Wind disturbances are the main source of tracking errors. This paper presents the development of a wind force model, and simulations of wind-induced pointing errors of DSN antennas. The antenna model includes the antenna structure, the elevation and azimuth servos, and the tracking controller. Simulation results show that pointing errors due to wind gusts are of the same order as due to wind static pressure, and that (similarly to the static wind pressure) these errors satisfy the velocity quadratic law. The methodology presented is used for wind disturbance estimation, and for design of an antenna controller with wind disturbance rejection properties.

Gawronski, W.↗
NASA NTRS1993

Cost and reliability study for a large array of small reflector antennas for JPL/NASA Deep Space Network (DSN)

A study performed to estimate the cost of an array of small aperture reflector antennas to be used instead of or in conjunction with the current large reflector antennas of the JPL/NASA Deep Space Network (DSN) is described. The arrays are used for servicing present and future NASA missions that involve smaller spacecraft with limited power and smaller, lower-gain antennas. The advantages of the array configuration in terms of cost and reliability are discussed. A probabilistic determination of the reliability and availability of the array as a function of the number of array elements and the availability of individual array elements is made. The impact of additional marginal elements on the operational availability of the array is studied. Parametric cost and reliability plots are presented and directions for further investigation are outlined.

Jamnejad, Vahraz↗
NASA NTRS1993

Cost and Reliability Study for a Large Array of Small Reflector Antennas for JPL/NASA Deep Space Network (DSN)

A study is performed to estimate the cost of an array of small aperture reflector antennas to be used instead or in conjunction with the current large reflector antennas of the JPL/NASA Deep Space Network (DSN), for servicing present and future NASA missions which involve smaller spacecraft with limited power and smaller, lower gain antennas. The advantages of the array configuration in terms of cost and reliability are studied. A probabilistic determination of the reliability and availability of the array as a function of the number of array elements and the availability of individual array elements is made. The impact of additional marginal elements on the operational availability of the array is studied. Parametric cost and reliability plots are presented and directions for further investigation are outlined.

Resch, G.↗
NASA NTRS1992

Pointing-error simulations of the DSS-13 antenna due to wind disturbances

Accurate spacecraft tracking by the NASA Deep Space Network (DSN) antennas must be assured during changing weather conditions. Wind disturbances are the main source of tracking errors. The development of a wind-force model and simulations of wind-induced pointing errors of DSN antennas are presented. The antenna model includes the antenna structure, the elevation and azimuth servos, and the tracking controller. Simulation results show that pointing errors due to wind gusts are of the same order as errors due to static wind pressure and that these errors (similar to those of static wind pressure) satisfy the velocity quadratic law. The presented methodology is used for wind-disturbance estimation and for the design of an antenna controller with wind-disturbance rejection properties.

Gawronski, W.↗
NASA NTRS1993

Design of the reduced LQG compensator for the Deep Space Network antennas

A linear quadratic Gaussian (LQG) compensator design procedure is proposed for the NASA Deep Space Network (DSN) antennas. The procedure is based on two properties of antennas. It is shown that tracking and flexible motion of the DSN antennas are almost independent (the separation property), and that for the balanced LQG compensator its performance is evenly divided between the controller and the estimator (balancing property). As a consequence compensators for the flexible and tracking parts can be designed separately, and the compensator order is reduced significantly, which is important for implementation purposes. The approach is illustrated with the detailed compensator design for the DSS-13 antenna.

Gawronski, W.↗
NASA NTRS1987

Antenna pointing systematic error model derivations

The pointing model used to represent and correct systematic errors for the Deep Space Network (DSN) antennas is presented. Analytical expressions are given in both azimuth-elevation (az-el) and hour angle-declination (ha-dec) mounts for RF axis collimation error, encoder offset, nonorthogonality of axes, axis plane tilt, and structural flexure due to gravity loading. While the residual pointing errors (rms) after correction appear to be within the ten percent of the half-power beamwidth criterion commonly set for good pointing accuracy, the DSN has embarked on an extensive pointing improvement and modeling program aiming toward an order of magnitude higher pointing precision.

Guiar, C. N.↗
NASA NTRS1988

The Feasibility of the Disturbance Accommodating Controller for Precision Antenna Pointing

The objective of this study is to investigate the feasibility of a pointing (position loop) controller for the NASA-JPL Deep Space Network (DSN) antennas using the Disturbance Accommodating Control (DAC) theory. A model that includes state dependent disturbances was developed, and an example demonstrating the noise estimator is presented as an initial phase in the controller design. The goal is to improve pointing accuracy by the removal of the systematic errors caused by the antenna misalignment as well as sensor noise and random wind and thermal disturbances. Preliminary simulation results show that the DAC technique is successful in both cancelling the imposed errors and maintaining an optimal control policy.

Gresham, L. L.↗
NASA NTRS1993

Radio metric errors due to mismatch and offset between a DSN antenna beam and the beam of a troposphere calibration instrument

Two components of the error of a troposphere calibration measurement were quantified by theoretical calculations. The first component is a beam mismatch error, which occurs when the calibration instrument senses a conical volume different from the cylindrical volume sampled by a Deep Space Network (DSN) antenna. The second component is a beam offset error, which occurs if the calibration instrument is not mounted on the axis of the DSN antenna. These two error sources were calculated for both delay (e.g., VLBI) and delay rate (e.g., Doppler) measurements. The beam mismatch error for both delay and delay rate drops rapidly as the beamwidth of the troposphere calibration instrument (e.g., a water vapor radiometer or an infrared Fourier transform spectrometer) is reduced. At a 10-deg elevation angle, the instantaneous beam mismatch error is 1.0 mm for a 6-deg beamwidth and 0.09 mm for a 0.5-deg beam (these are the full angular widths of a circular beam with uniform gain out to a sharp cutoff). Time averaging for 60-100 sec will reduce these errors by factors of 1.2-2.2. At a 20-deg elevation angle, the lower limit for current Doppler observations, the beam-mismatch delay rate error is an Allan standard deviation over 100 sec of 1.1 x 10(exp -14) with a 4-deg beam and 1.3 x 10(exp -l5) for a 0.5-deg beam. A 50-m beam offset would result in a fairly modest (compared to other expected error sources) delay error (less than or equal to 0.3 mm for 60-sec integrations at any elevation angle is greater than or equal to 6 deg). However, the same offset would cause a large error in delay rate measurements (e.g., an Allan standard deviation of 1.2 x 10(exp -14) over 100 sec at a 20-deg elevation angle), which would dominate over other known error sources if the beamwidth is 2 deg or smaller. An on-axis location is essential for accurate troposphere calibration of delay rate measurements. A half-power beamwidth (for a beam with a tapered gain profile) of 1.2 deg or smaller is desired for calibration of all types of radio metrics. A water-vapor radiometer calibration beam of this size with very low sidelobes would require a clear aperture antenna with a diameter of at least 1.5 m if the primary water vapor sensing channel were in the 20-22 GHz range.

R P Linfield↗
NASA NTRS1991

Mark 4A antenna control system data handling architecture study

A high-level review was conducted to provide an analysis of the existing architecture used to handle data and implement control algorithms for NASA's Deep Space Network (DSN) antennas and to make system-level recommendations for improving this architecture so that the DSN antennas can support the ever-tightening requirements of the next decade and beyond. It was found that the existing system is seriously overloaded, with processor utilization approaching 100 percent. A number of factors contribute to this overloading, including dated hardware, inefficient software, and a message-passing strategy that depends on serial connections between machines. At the same time, the system has shortcomings and idiosyncrasies that require extensive human intervention. A custom operating system kernel and an obscure programming language exacerbate the problems and should be modernized. A new architecture is presented that addresses these and other issues. Key features of the new architecture include a simplified message passing hierarchy that utilizes a high-speed local area network, redesign of particular processing function algorithms, consolidation of functions, and implementation of the architecture in modern hardware and software using mainstream computer languages and operating systems. The system would also allow incremental hardware improvements as better and faster hardware for such systems becomes available, and costs could potentially be low enough that redundancy would be provided economically. Such a system could support DSN requirements for the foreseeable future, though thorough consideration must be given to hard computational requirements, porting existing software functionality to the new system, and issues of fault tolerance and recovery.

Briggs, H. C.↗
NASA NTRS1984

Radio interferometric determination of intercontinental baselines and earth orientation utilizing deep space network antennas - 1971 to 1980

Progress has been made toward the realization of the potential of radio interferometry for measuring crustal motions and global rotations of the earth with accuracies at the centimeter level. In this connection, a series of experiments, primarily with NASA's Deep Space Network (DSN) antennas, has been conducted to develop two generations of very long baseline interferometric (VLBI) systems. A description is presented of the employed techniques, an analysis of the experiments, and the results of geophysical significance. Attention is given to the interferometry technique, the geometric delay model, propagation media calibrations, and the observing strategy.

Sovers, O. J.↗
NASA NTRS2009

Estimating Transmitted-Signal Phase Variations for Uplink Array Antennas

A method of estimating phase drifts of microwave signals distributed to, and transmitted by, antennas in an array involves the use of the signals themselves as phase references. The method was conceived as part of the solution of the problem of maintaining precise phase calibration required for proper operation of an array of Deep Space Network (DSN) antennas on Earth used for communicating with distant spacecraft at frequencies between 7 and 8 GHz. The method could also be applied to purely terrestrial phased-array radar and other radio antenna array systems. In the DSN application, the electrical lengths (effective signal-propagation path lengths) of the various branches of the system for distributing the transmitted signals to the antennas are not precisely known, and they vary with time. The variations are attributable mostly to thermal expansion and contraction of fiber-optic and electrical signal cables and to a variety of causes associated with aging of signal-handling components. The variations are large enough to introduce large phase drifts at the signal frequency. It is necessary to measure and correct for these phase drifts in order to maintain phase calibration of the antennas. A prior method of measuring phase drifts involves the use of reference-frequency signals separate from the transmitted signals. A major impediment to accurate measurement of phase drifts over time by the prior method is the fact that although DSN reference-frequency sources separate from the transmitting signal sources are stable and accurate enough for most DSN purposes, they are not stable enough for use in maintaining phase calibrations, as required, to within a few degrees over times as long as days or possibly even weeks. By eliminating reliance on the reference-frequency subsystem, the present method overcomes this impediment. In a DSN array to which the present method applies (see figure), the microwave signals to be transmitted are generated by exciters in a signal-processing center, then distributed to the antennas via optical fibers. At each antenna, the signals are used to drive a microwave power-amplifier train, the output of which is coupled to the antenna for transmission. A small fraction of the power-amplifier-train output is sent back to the signal-processing center along another optical fiber that is part of the same fiber-optic cable used to distribute the transmitted signal to the antenna. In the signal-processing center, the signal thus returned from each antenna is detected and its phase is compared with the phase of the signal sampled directly from the corresponding exciter. It is known, from other measurements, that the signal-propagation path length from the power-amplifier-train output port to the phase center of each antenna is sufficiently stable and, hence, that sampling the signal at the power-amplifier-train output port suffices for the purpose of characterizing the phase drift of the transmitted signal at the phase center of the antenna

Paal, Leslie↗
NASA NTRS2007

DSN Resource Scheduling

TIGRAS is client-side software, which provides tracking-station equipment planning, allocation, and scheduling services to the DSMS (Deep Space Mission System). TIGRAS provides functions for schedulers to coordinate the DSN (Deep Space Network) antenna usage time and to resolve the resource usage conflicts among tracking passes, antenna calibrations, maintenance, and system testing activities. TIGRAS provides a fully integrated multi-pane graphical user interface for all scheduling operations. This is a great improvement over the legacy VAX VMS command line user interface. TIGRAS has the capability to handle all DSN resource scheduling aspects from long-range to real time. TIGRAS assists NASA mission operations for DSN tracking of station equipment resource request processes from long-range load forecasts (ten years or longer), to midrange, short-range, and real-time (less than one week) emergency tracking plan changes. TIGRAS can be operated by NASA mission operations worldwide to make schedule requests for the DSN station equipment.

Wang, Yeou-Fang↗
NASA NTRS1986

Design considerations for the beam-waveguide retrofit of a ground antenna station

Retrofitting an antenna that was originally designed without a beam waveguide introduces special difficulties because it is desirable to minimize alteration of the original mechanical truss work and to image the actual feed without distortion at the focal point of the dual-shaped reflector. To obtain an acceptable image, certain Geometrical Optics (GO) design criteria are followed as closely as possible. The problems associated with applying these design criteria to a 34-meter dual-shaped DSN (Deep Space Network) antenna are discussed. The use of various diffraction analysis techniques in the design process is also discussed. GTD and FFT algorithms are particularly necessary at the higher frequencies, while Physical Optics and Spherical Wave Expansions proved necessary at the lower frequencies.

Veruttipong, T.↗
NASA NTRS1985

Planning for VLA/DSN arrayed support to the Voyager at Neptune

Preplanning for the use of the National Radio Astronomy Observatory's Very Large Array (VLA) in support of Voyager at Neptune has been underway since early 1982. When arrayed with the Deep Space Network (DSN) antennas at Goldstone, CA, the VLA more than doubles the potential data return over the American longitude for the 1989 Voyager encounter. The background, rationale and current status of planning for VLA-DSN Arrayed Support to the Voyager at Neptune are discussed.

Layland, J. W.↗
NASA NTRS1988

Multiple-Feed Design For DSN/SETI Antenna

Frequency bands changed with little interruption of operation. Modification of feedhorn mounting on existing 34-m-diameter antenna in Deep Space Network (DSN) enables antenna to be shared by Search for Extra-Terrestrial Intelligence (SET) program with minimal interruption of DSN spacecraft tracking. Modified antenna useful in terrestrial communication systems requiring frequent changes of operating frequencies.

Slobin, S. D.↗