Search NASA⌕ Search

SEARCH · Search NASA

Results for “Delamination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Electrochemical mechanisms of leakage-current-enhanced delamination and corrosion in Si photovoltaic modules

This paper analyzes the mechanisms for corrosion and delamination observed in Si photovoltaic modules subjected to high temperature and humidity with a negative-ground bias testing. Based on the thermodynamic data, the ionic component of the leakage current causes reduction reactions of water on the cathodic metallization, producing hydrogen gas and hydroxide ions. Ag fingers are strong catalysts for this reduction reaction compared to other materials used in solar cells and can be the initiation sites of corrosion and delamination caused by the electrochemical reactions. The produced hydrogen gas accumulates inside the module potentially producing a high gas pressure that can promote delamination, which is often preferentially initiated on metallization where the adhesion strength is lower [1], [2], [3]. The local basicity near the metal surface increases due to the hydroxide ion generation. Thus, the environment inside the encapsulant can be alkaline despite the presence of acetic acid decomposition products from the encapsulant. Corrosion of materials such as Si used in solar cells occurs and the extent depends on their corrosion resistance to the alkaline solution. This suggests that corrosion and delamination are interactive and promote the formation and propagation of one another.

14 SOLAR ENERGY↗
DOE OSTI2026

Delamination recycling of multilayer plastic films: Solvent-assisted separation pathways and recovery of solid polyolefins

Multilayer plastic films are excellent packaging materials due to the bound layers of multiple polymers, with each different polymer contributing to the film properties. Desirable properties lead to continuously growing demand for multilayer films. Multilayer plastic films are typically single-use and, as such, their increased production and disposal have led to waste management problems. Multilayer films are not currently recyclable primarily due to the multiple bound polymers. This work advances delamination as a recycling process to separate and sequester valuable polymers from multilayer films, facilitating the incorporation of these polymers into the circular economy. We effect delamination in a physical process that preserves targeted polymers as solid film, hence retaining their embodied energy. This work documents three different pathways of inducing delamination of multilayer films, with appropriate solvents disrupting adhesion between adjacent layers or dissolving a minor component of the film in less than an hour and at temperatures below 90°C, and where all initial polyethylene is maintained in its solid form throughout the process and is recovered at high purity. Solvent-based delamination is exemplified on commercial multilayer films with majority polyethylene (PE), and polyethylene terephthalate (PET) or ethylene vinyl alcohol copolymer (EVOH) or nylon also present. Solvent-based delamination is an energy-efficient and environmentally friendly recycling process that improves upon dissolution-precipitation recycling, since delamination involves very little dissolution and no precipitation, and is superior to pyrolysis which breaks down the polymers, while delamination keeps polymer chains intact. Furthermore, delamination recycling can contribute to the sustainable use of multilayer films as they continue to protect our food and medicine.

Chemical Recycling↗
DOE OSTI2018

SSZ-70 Borosilicate Delamination Without Sonication: Effect of Framework Topology on Olefin Epoxidation Catalysis

Here, we report a scalable delamination procedure for a SSZ-70-framework layered-zeolite precursor, which for the first time does not involve either sonication or long-chain surfactants. Our approach instead relies on the mild heating of layered zeolite precursor B-SSZ-70(P) in an aqueous solution containing Zn(NO 3 ) 2 and tetrabutylammonium fluoride. Powder X-ray diffraction data are consistent with a loss of long-range order along the z-direction, while 29 Si MAS NMR spectroscopy demonstrates preservation of the zeolite framework crystallinity during delamination. The resulting delaminated material, DZ-2, possesses 1.4-fold higher external surface area relative to the nondelaminated three-dimensional zeolite B-SSZ-70, based on N2 physisorption data at 77 K. DZ-2 was functionalized with cationic Ti heteroatoms to synthesize Ti-DZ-2 via exchange with framework B. Ti-DZ-2 contains isolated titanium centers in its crystalline framework, as shown by UV-Vis spectroscopy. The generality of the synthetic delamination approach and catalyst synthesis is demonstrated with the synthesis of delaminated material DZ-3, which is derived from layered zeolite precursor ERB-1(P) with MWW framework topology. Upon catalytic testing for the epoxidation of 1-octene with ethylbenzene hydroperoxide as oxidant, under harsh tail-end conditions that deactivate amorphous Ti-silica-based catalysts, Ti-DZ-2 exhibits the highest per-Ti-site activity, selectivity, and stability for 1-octene epoxidation of all catalysts investigated. This testing includes the prior benchmark delaminated zeolite catalyst in this area, Ti-UCB-4, which possesses similar external surface area to Ti-DZ-2 but requires sonication and long-chain surfactants for its synthesis. The synthesis of DZ-2 is the first example of an economical delamination of layered zeolite precursor SSZ-70(P) and opens up new doors to the development of delaminated zeolites as commercial catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Delamination-informed lifecycle decisions: A dielectric and machine learning framework for composite sorting and recycling

Composite materials are widely used in aerospace, marine, and automotive sectors due to their high strength-to-weight ratio and durability. However, their long-term reliability can be compromised by damage accumulation. Specifically, delamination initiation serves as a precursor to structural failure, which is often difficult to detect during damage inspection. Identifying and sorting delamination initiation in samples not only increases operational safety while providing critical information for end-of-life decisions, which influences both the service life extension value and the efficiency of fiber extraction during recycling. This research addresses two challenges: (1) developing a nondestructive, ex-situ framework to sort composite materials based on damage severity, particularly delamination, and (2) understanding how damage in composites influences resin removal during pyrolysis. Both experimental work and finite element analysis were performed to predict critical stress levels that are associated with delamination onset. Based on these results, three loading levels 50 %, 75 %, and 90 % of maximum stress, were selected for controlled experiments, generating composite samples with varying extents of damage for machine learning model training. Microscopic imaging of these samples confirmed the damage progression from matrix cracking to delamination, validating the computational predictions. We explored supervised machine learning using dielectric measurements to classify damage states. Preliminary results show an artificial neural network can identify early delamination which is a potential precursor to failure, with 94.44 % accuracy on our dataset. A parallel investigation into the effect of damage severity on pyrolysis recycling showed that heavily delaminated samples required significantly less energy for comparable matrix removal than undamaged samples.

dielectric variables↗
DOE OSTI2020

Quantifying thermal barrier coating delamination through luminescence modeling

Thermal barrier coatings (TBCs) are widely used in the hot sections of gas turbine systems as they are remarkably efficient in insulating the underlying superalloys, leading to higher operating temperatures and therefore enhancing the performance of the engines. However, this benefit is only possible if the integrity of the TBC under aggressive thermo-mechanical environments is ensured. Delamination is a common but hard to detect failure mode. We present, in this work, supported by experimentation, the implementation of a modeling approach applying the Kubelka-Munk theory to provide numerical quantification of luminescence contrast and intensity due to top coat delamination in TBCs. The method relies on the drastic change in reflectivity when a delamination forms, exploiting it for high-contrast luminescence mapping. Two distinct TBC configurations containing an erbium-doped yttria-stabilized zirconia (YSZ:Er 3+ ) layer for delamination sensing were used to validate this model. A delamination zone induced by Rockwell indentation was successfully tracked by measuring an increase of the intensity of the erbium emission line at 562 nm. Luminescence-based methods for delamination detection can provide a revolutionary non-invasive technique, with potential for both off-line and on-line engine monitoring.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Minimization of Cathode|Solid-Electrolyte Interfacial Delamination through the Application of Interphase Layers

Next-generation lithium-ion batteries are expected to use solid electrolytes (SEs) to enable higher energy density and extreme fast-charge capabilities. One major mode of degradation at the cathode|SE interface is delamination between the cathode active materials and SEs, which leads to performance decay. Experimental observations indicate that implementation of interphase layers can minimize the cathode|SE delamination induced capacity fade. A multiscale computational methodology is developed here to investigate the applicability of boron substituted lithium carbonate (Li 2+x B x C 1–x O 3 , x = 0.5, or LBCO) to minimize the delamination at the cathode|SE interface. Atomistic simulations indicate that the fracture energies at both the cathode|LBCO and LBCO|SE interfaces are higher than those at the cathode|SE interface, which reduces the extent of delamination. Mesoscale simulations indicate that, apart from increasing the fracture energy, decreasing the evolution of strain energy by lowering the elastic modulus of the interphase layer can also minimize the extent of delamination at the cathode|SE interface. However, the adoption of an interphase layer with high ionic conductivity is necessary to minimize the ohmic losses during operation at higher current densities. This study provides guidance on selecting interphase layers with specific properties and thicknesses to minimize both interfacial delamination and impedance growth.

LBCO↗
DOE OSTI2018

The Effect of Aging on the Delamination Fracture Energy of Glass Solar Reflectors

Thin metal and metal oxide films deposited on glass or polymer substrates have been widely applied to manufacture front surfaced solar reflectors such as those used in the concentrated solar power (CSP) systems due to the facts that they are highly transparent, resistant to ultraviolet (UV) light and abrasion, and chemically inert. However, the reliable operation over long periods of outdoor exposure of such solar reflectors depends on the adequate adhesion between each layer to prevent delamination and subsequent failure. We report results from measurements of the delamination fracture energy (DFE) of the weakest interface in both as-deposited and aged reflectors, where the reflector construction consists of a glass/copper/silver/oxide stack. In this study, DFE was measured using a width-tapered beam method and the test results showed that the weakest interface of this solar reflector is the copper-glass interface, with a delamination fracture energy of approximately 4.4 J/m 2 . In order to verify the test results, finite element (FE) simulations were run using the commercial software package ABAQUS 6.14 based on the cohesive zone model (CZM). In the simulations, the DFE derived from the delamination measurement was treated as an input and the delamination forces from the FE simulations were compared to the experimental results. The good agreement between the tested and simulated delamination force indicated that this width-tapered beam method is accurate even for very small DFE, making it appropriate to test the DFE of front surfaced glass solar reflectors. Additionally, in order to study the aging effect on the DFE, accelerated aging tests were conducted using samples with different protective coatings, one group of samples with alumina ( Al 2 O 3 ) protective coating and the other group with titania ( TiO 2 ) protective coating. The DFE after 50 and 100 hours of accelerated aging were measured. The test results showed that the copper-glass interface would still be the weakest interface for all samples after aging, and the DFE for samples with Al 2 O 3 protective coating was unchanged whereas the copper-glass interface was found to undergo statistically significant change after both 50 and 100 hours of aging for samples with TiO 2 protective coating. We found that DFE at the copper/glass interface decreased after 50 hours of aging then increased after 100 hours of aging. The origin of this non-monotonic response of TiO 2 coated reflectors under accelerated aging conditions is unknown.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Competitive grain boundary segregation of phosphorus and carbon governs delamination crack in a ferritic steel

Highlights: • Trace amounts of P in the steel cause delamination in case of Lt-high Temp. holding. • Anisotropic microstructure did not affect the delamination in this study. • Crack-linked GBs in Lt-high Temp. steel had higher P and lower C segregation. • Crack-interrupt GBs in St-high Temp. steel had lower P and higher C segregation. • Competitive segregation controlled by high Temp. holding time affects delamination. - Abstract: The present study aims at unveiling the influence of trace amounts of phosphorus on the macro-scale delamination in a ferritic steel. Two different steels with trace amounts of phosphorus were examined to reveal the cause: One was made by long-time high temperature holding to maximize the phosphorus segregation, and the other one was made by short-time high temperature holding to minimize the phosphorus segregation. The atom probe results at the grain boundaries ahead of the delamination-related cracks provide a strong evidence that phosphorus-enrichment and carbon-depletion for the long-time high temperature holding induces a larger degree of delamination as compared to the short-time high temperature holding. Reasons for the different segregation tendency were discussed by correlating the isothermal holding time at high temperature and the competitive segregation between phosphorus and carbon.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Delamination of Multilayer Plastic Films to Recover Polyethylene with Favorable Mechanical Properties

Multilayer plastic films play a critical role in packaging, with each polymer layer contributing specific properties to the multilayer film. Multilayer plastic films are not currently recyclable due to the bound polymers. With multilayer film production of about 20 million metric tons in 2024 and rising, endof- life treatment becomes pressing. This work presents a scalable solvent-based delamination recycling process that is applied to commercial postindustrial multimaterial films to unbind the materials within a multilayer film by dissolving only the adhesive layer and recover polyethylene (PE) as an intact solid film. Solventbased delamination is a simple process that allows the complete recovery of materials and solvents used in the process. The delaminating solvent, 88% formic acid in water, induces delamination of PE/PEI/PET and PE/PU/PET films at 70 °C in under an hour. Recovered PE has no contamination detected by Fourier transform infrared spectroscopy and mechanical properties on par with those of virgin resin. The recovery of high-quality solid PE film fit for reprocessing, at low operating temperatures and with closed-loop solvent reuse, promotes delamination as a low energy consumption and environmentally friendly recycling process. PE recovered from delamination can be reused in equivalent products, promoting circularity of multimaterial films.

chemical recycling↗
DOE OSTI2018

Mitigation of Crack Formation During Thermo-Mechanical Delamination of CdTe Solar Cells

Controlled thermo-mechanical delamination of thin-film solar cells offers a promising approach to drastically improve flexibility and specific power (power-to-weight ratio). However, the issue of film cracking during the delamination process must first be addressed. Here, we examine the causes of cracking during and after delamination, where it is found that cracking is heavily influenced by the material properties of the stressor layer used to induce delamination and the glass substrate that the solar cell is grown on. We then present several ways to reduce cracking during the delamination process.

14 SOLAR ENERGY↗
DOE OSTI2023

Delamination imaging in composites using cross-correlation method by non-contact air-coupled Lamb waves

Abstract This paper presents a cross-correlation damage detection technique using damage scattered waves of all directions cross-correlate with the incident waves for delamination imaging in carbon fiber reinforced polymer (CFRP) composite plate. The presented imaging can not only detect the delamination but also precisely quantify the damage with locations and sizes. First, a CFRP composite sample with interlaminar delamination by inserting the Teflon layer is designed and manufactured in house using the hot-press machine. And a three-dimensional model of composite sample is simulated using the finite element method. Next, the cross-correlation imaging algorithm is introduced in detail, and the cross-correlation imaging proof-of-concept study is conducted with the simulated Lamb waves in the composite sample. Finally, a fully non-contact air-coupled transducer and scanning laser Doppler vibrometer system with a single-mode Lamb wave method is established to actuate and sense the interrogating Lamb waves in the structure. The imaging method is experimentally implemented for the one delamination and two delaminations imaging and quantification.

Instruments & Instrumentation↗
DOE OSTI2024

Predicting the Rate of Degradation Related to Oxygen Electrode Delamination in Solid Oxide-Ion Electrolyzers

One of the leading causes for the performance degradation in H 2 -producing solid oxide electrolytic cells (SOECs) is the gradual delamination of oxygen electrode (OE) from the electrolyte under a strong anodic polarization. Identification of the key factor that controls the rate of OE delamination is of paramount importance to achieve long-term stable operation of SOECs. Here we show from thousands of hours of testing data that the exchange current density (i°) of OE can be leveraged as a predictor for the rate of delamination. To obtain i°, we apply DC-biased electrochemical impedance spectroscopy on a three-electrode symmetrical cell to measure polarization resistance (R p ) of OE as a function of current density (i) and time (t). The collected R p -i-t raw data are then converted to overpotential ( η )-i-t, from which i° is extracted from the “low-field” approximation. An analytical relationship between i° and time-to-delamination (TTD) is further established from the established i°-i-t relationship. We show that under a constant anodic polarization current density i, the greater the ratio i/i°, the faster the delamination. Therefore, we conclude that the exchange current density of an OE, i°, can be used to predict the rate of OE degradation in solid oxide-ion electrolyzers.

25 ENERGY STORAGE↗
DOE OSTI2023

Task 12 PV Sustainability - Life Cycle Assessment of Crystalline Silicon Photovoltaic Module Delamination with Hot Knife Technology

The objective of this study is to complete a life cycle assessment (LCA) of a novel technology that separates the crystalline silicon (c-Si) photovoltaic (PV) module front glass from the backsheet using hot knife technology. This is known to be the most challenging step in module recycling, where the choice of delamination approach can determine the process selection for the next steps of the recycling process, the economic value of the recovered materials, and environmental performance. The life cycle inventory (LCI) reported here is based on primary data from the technology manufacturer. Different LCIs are established following the cut-off approach and the end-of-life (EOL) approach. The environmental impacts of the hot knife delamination process are analysed based on six indicators, and the main contributors to delamination efforts are identified. For the EOL approach, the potential environmental benefits from the recovered materials are compared to the environmental impacts caused by the delamination process. The functional unit of this analysis is the delamination of 1 kg of used framed c-Si PV modules at the place of installation.

14 SOLAR ENERGY↗
DOE OSTI2022

Multiphysics modeling of SOFC performance degradation caused by interface delamination and active layer cracking

In solid oxide device operation, delamination and cracking cause more catastrophic damage to cell life than other degradation mechanisms, leading to more rapid cell failure. The electrochemical performance degradation caused by electrode/electrolyte interface delamination and active layer cracking were investigated through in-house developed three-dimensional multiphysics simulations. Here the multiphysics simulations, fully calibrated against experimental datasets for button cells in a previous study, were extended to quantitatively investigate the effects of electrode/electrolyte interface delamination and active layer cracking. The simulated polarization curves and impedance behavior with various levels of delamination and cracking provided insights of the performance degradation. Furthermore, the local current distributions within the cell were analyzed for three different operating modes: constant voltage, constant current, and constant power. Finally, a practical strategy was proposed to mitigate the performance degradation in the realistic cell operations, extending overall cell lifetime.

08 HYDROGEN↗
DOE OSTI2018

Environmental Influence on Module Delamination Rate

Here, this study begins to investigate the role of environmental factors, such as temperature and humidity, on the delamination kinetics of the ethylene vinyl acetate (EVA)/silicon-photovoltaic (Si-PV) cell interface. A fracture mechanics approach based on a single cantilever beam technique is employed to measure the delamination rate as a function of applied driving force. To glean insight into the mechanisms of bonding and degradation at this interface, and the effect of manufacturing variability and quality, we consider a high-quality pristine EVA and two EVAs formulated with reduced amounts of its adhesion promoter, silane. Results indicate that a bulk change in the viscoelastic properties of the EVA dominates the delamination kinetics at high driving forces and low humidity and the effect of a chemical reaction only becomes apparent at higher humidity and lower driving forces. These findings suggest that only interfacial phenomenon of susceptible, degraded material may have to be considered to adequately model PV module delamination failure.

14 SOLAR ENERGY↗
DOE OSTI2023

Understanding and Mitigating the Dissolution and Delamination Issues Encountered with High-Voltage LiNi 0.5 Mn 1.5 O 4

In our initial study on the high-voltage 5 V cobalt-free spinel LiNi 0.5 Mn 1.5 O 4 (LNMO) cathode, we discovered a severe delamination issue in the laminates when cycled at a high upper cut-off voltage (UCV) of 4.95 V, especially when a large cell format was used. This delamination problem prompted us to investigate further by studying the transition metal (TM) dissolution mechanism of cobalt-free LNMO cathodes, and as a comparison, some cobalt-containing lithium nickel manganese cobalt oxides (NMC) cathodes, as the leachates from the soaking experiment might be the culprit for the delamination. Unlike other previous reports, we are interested in the intrinsic stability of the cathode in the presence of a baseline Gen2 electrolyte consisting of 1.2 M of LiPF 6 in ethylene carbonate/ethyl methyl carbonate (EC/EMC), similar to a storage condition. The electrode laminates (transition metal oxides, transition metal oxides, TMOs, coated on an Al current collector with a loading level of around 2.5 mAh/cm 2 ) or the TMO powders (pure commercial quality spinel LNMO, NMC, etc.) were stored in the baseline solution, and the transition metal dissolution was studied through nuclear magnetic resonance, such as 1 H NMR, 19 F NMR, scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). Significant electrolyte decomposition was observed and could be the cause that leads to the TM dissolution of LNMO. To address this TM dissolution, additives were introduced into the baseline electrolyte, effectively alleviating the issue of TM dissolution. The results suggest that the observed delamination is caused by electrolyte decompositions that lead to etching, and additives such as lithium difluorooxalato borate and p-toluenesulfonyl isocyanate can alleviate this issue by forming a firm cathode electrolyte interface. This study provides a new perspective on cell degradation induced by electrode/electrolyte interactions under storage conditions.

25 ENERGY STORAGE↗