Search NASASearch

SEARCH · Search NASA

Results for “Deployable heat shields”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Landing Characteristics of the Apollo Spacecraft with Deployed Heat Shield Impact Attenuation Systems

An experimental investigation was made to determine the landing characteristics of a 1/4-scale dynamic model of the Apollo spacecraft command module using two different active (heat shield deployed prior to landing) landing systems for impact attenuation. One landing system (configuration 1) consisted of six hydraulic struts and eight crushable honeycomb struts. The other landing system (configuration 2), consisted of four hydraulic struts and six strain straps. Tests made on water and the hard clay-gravel composite landing surfaces simulated parachute letdown (vertical) velocities of 23 ft/sec (7.0 m/s) (full scale). Landings made on the sand landing surface simulated vertical velocities of 30 ft/sec (9.1 m/s). Horizontal velocities of from 0 to 50 ft/sec (15 m/s) were simulated. Landing attitudes ranged from -30'degrees to 20 degrees, and the roll attitudes were O degrees, 90 degrees, and 180 degrees. For configuration 1, maximum normal accelerations at the vehicle center of gravity for landings on water, sand, and the hard clay-gravel composite surface were 9g, 20g, and 18g, respectively. The maximum normal center-of-gravity acceleration for configuration 2 which was landed only on the hard clay-gravel landing surface was approximately 19g. Accelerations for configuration 2 were generally equal to or lower than accelerations for configuration 1 and normal.

EXPERIMENTS

Progress in Payload Separation Risk Mitigation for a Deployable Venus Heat Shield

A deployable decelerator known as the Adaptive Deployable Entry and Placement Technology (ADEPT) offers substantial science and mass savings for the Venus In Situ Explorer (VISE) mission. The lander and science payload must be separated from ADEPT during atmospheric entry. This paper presents a trade study of the separation system concept of operations and provides a conceptual design of the baseline: aft-separation with a subsonic parachute. Viability of the separation system depends on the vehicle's dynamic stability characteristics during deceleration from supersonic to subsonic speeds. A trajectory sensitivity study presented shows that pitch damping and Venusian winds drive stability prior to parachute deployment, while entry spin rate is not a driver of stability below Mach 5. Additionally, progress in free-flight CFD techniques capable of computing aerodynamic damping parameters is presented. Exploratory simulations of ADEPT at a constant speed of Mach number of 0.8 suggest the vehicle may have an oscillation limit cycle near 5 angle-of-attack. The proposed separation system conceptual design is thought to be viable.

Smith, Brandon P.

Mars Molniya Orbit Atmospheric Resource Mining

This NASA Innovative Advanced Concepts (NIAC) Phase I study examined the revolutionary concept of performing resource collection and utilization during Mars orbital operations in order to enable the landing of large payloads. An exploration architecture was developed, out of which several mission alternatives were developed. Concepts of operations were then developed for each mission alternative, followed by concepts for spacecraft systems, which were traded to assess their feasibility. A novel architecture using Mars Molniya Orbit Atmospheric Resource Mining is feasible to enable an Earth-independent and pioneering, permanent human presence on Mars by providing a reusable, single-stage-to-orbit transportation system. This will allow cargo and crew to be routinely delivered to and from Mars without transporting propellants from Earth.In Phase I, our study explored how electrical energy could be harnessed from the kinetic energy of the incoming spacecraft and then be used to produce the oxygen necessary for landing. This concept of operations is revolutionary in that its focus is on using in situ resources in complementary and varied forms: the upper atmosphere of Mars is used for aerocapture, which is followed by aerobraking, the kinetic energy of the spacecraft is transformed into usable electrical energy during aerobraking, and the atmospheric composition is the source of oxidizer for a landing under supersonic retropropulsion. This NASA Innovative Advanced Concepts (NIAC) Phase I study explores a novel mission architecture to establish routine, Earth-independent transfer of large mass payloads between Earth and the Mars surface and back to Mars orbit. The first stage of routine mission operations involves an atmospheric resource mining aerobraking campaign following aerocapture into a highly elliptical Mars orbit. During each pass through the atmosphere, the vehicle ingests the atmospheric oxidizer and stores it onboard, using solid oxide electrolysis to convert the primarily CO2 atmosphere into usable O2 for propellant. Power is made available through the use of magnetohydrodynamic energy generation, which converts the motion of the plasma in the shock later into usable electrical energy. Upon termination of the aerobraking sequence, the descent vehicle detaches from the orbit stack, deorbits, and executes the entry, descent, and landing sequence. Hypersonic deceleration is achieved via a deployable heat shield to lower the vehicle ballistic coefficient, and supersonic and subsonic deceleration are achieved via retropropulsion. Mars surface operations involve resource mining of the Martian regolith to produce CH4 and O2 propellant to be used for the subsequent MDAV ascent back to high Mars orbit (HMO) providing an apoapsis raise maneuver to initialize the aerobraking sequence, in addition to providing fuel from the Mars surface for EDL propulsive descent. The Resource Collector Vehicle (RCV), which is used for the orbital mining operations, is raised back to HMO via onboard deployable augmented solar electric propulsion. Concepts of operations were developed for each mission alternative, to evaluate between them and assess feasibility.

Mining

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview, Science Return, and Future Applications of This Technology

The Low-Earth Orbit (LEO) Flight Test of an Inflatable Decelerator (LOFTID) mission was the culmination of two decades of research and development for Hyper-sonic Inflatable Aerodynamic Decelerator (HIAD) technology. LOFTID was a project overseen by the Technology Demonstration Mission (TDM) program within NASA’s Space Technology Mission Directorate. The success of the LOFTID mission could enable new NASA missions to Mars, Venus, and most solar-system destinations with atmospheres, as well as cost-effective payload returns to Earth, including in-space manufactured materials and launch vehicle asset recovery. LOFTID, with its unique inflatable heat shield, was the first-of-a-kind orbital reentry flight, and the largest blunt body atmospheric entry of any kind. On November 10, 2022, just over 10 years since the previous flight test of the smaller sub-orbital Inflatable Reentry Vehicle Experiment-3 (IRVE-3) [1], NASA Langley Research Center, with partner United Launch Alliance (ULA), successfully launched and achieved reentry and recovery of the LOFTID Reentry Vehicle (RV), further demonstrating the viability of the HIAD technology for large-diameter, inflatable heat shields to safely and accurately deliver large payloads through an atmosphere via a controlled descent and landing. Launching as a secondary payload with the Joint Polar Satellite System 2 (JPSS-2) from Vandenberg Space Force Base, California, stowed inside an ex-tended payload adapter of the Atlas V 401 launch vehicle, the LOFTID mission officially began after the JPSS-2 payload was delivered to its orbit by the Centaur second stage. The LOFTID RV was flying solo on its spin-stabilized ballistic reentry trajectory about one hour after launch, and the flight ended approximately one hour later with a gentle splashdown under parachute in the Pacific Ocean off the east coast of Hawaii, where the RV was recovered and later shipped back to NASA Langley. LOFTID endured the harsh environments of atmospheric reentry while demonstrating stable aerodynamics through the entire spectrum of hypersonic, supersonic, transonic, and subsonic flight. The LOFTID RV was exposed to an aeroheating environment representative of many Mars and LEO HIAD applications, while successfully demonstrating the ability of the heat-affected inflatable structure to with-stand aerodynamic forces that exceeded those expected at Mars. This flight demonstration of a 6m diameter HIAD confirmed the technology structural and thermal performance as it protected the 1100kg RV entering Earth’s atmosphere at 8 km/s, reaching Mach 30, and experiencing 9g deceleration before deploying parachutes and splashing down in the Pacific Ocean. HIAD technology involves an aeroshell that can be hard packed into a small volume for launch and then deployed prior to atmospheric entry for a controlled deceleration through the atmosphere. Large deployable heat shields enable spacecraft to carry bigger, heavier payloads, including scientific instruments and human support systems for planetary landing and exploration. Much larger than traditional fixed diameter aeroshells that are constrained by the size of launch vehicle shrouds, inflatable decelerators create more drag and start the deceleration process in the upper reaches of the atmosphere with greater efficiency and stability. LOFTID’s successful demonstration of the HIAD technology has greatly expanded NASA’s options for future planetary missions and opened new commercial opportunities for lower-cost mission pay-load recovery including recovery of launch vehicle assets, or as a delivery system to return cargo from the International Space Station or cislunar space. The developments for some of these applications are al-ready underway. While LOFTID was indeed a first-of-a-kind flight for an inflatable heatshield, the largest blunt-body entry ever, its remarkable performance assured that it will not be the last of its kind.

John DiNonno

Mars Exploration Rover Heat Shield Recontact Analysis

The twin Mars Exploration Rover missions landed successfully on Mars surface in January of 2004. Both missions used a parachute system to slow the rover s descent rate from supersonic to subsonic speeds. Shortly after parachute deployment, the heat shield, which protected the rover during the hypersonic entry phase of the mission, was jettisoned using push-off springs. Mission designers were concerned about the heat shield recontacting the lander after separation, so a separation analysis was conducted to quantify risks. This analysis was used to choose a proper heat shield ballast mass to ensure successful separation with low probability of recontact. This paper presents the details of such an analysis, its assumptions, and the results. During both landings, the radar was able to lock on to the heat shield, measuring its distance, as it descended away from the lander. This data is presented and is used to validate the heat shield separation/recontact analysis.

Raiszadeh, Behzad

Pterodactyl: An Uncoupled Range Control Approach to Fully Numerical Predictor-Corrector Entry Guidance

Entry, descent, and landing (EDL) has been identified as a core area of investment in NASA's Strategic Technology Investment Plan (NASA STIP). STIP lists the space technologies needed to help achieve NASA's science, technology, and exploration goals across the agency. Within the EDL core area, deployable hypersonic decelerators, also known as deployable entry vehicles (DEVs), have been identified as an area of investment, due to its potential to revolutionize payload delivery methods to Earth and other planets. These vehicles, which can deploy their heat shields or alter their shape before entry, exploit an increased and more effective drag ratio by using less mass than traditional blunt body vehicles with rigid aeroshells. DEVs like Adaptive Deployable Entry and Placement Technology (ADEPT) and Hypersonic Inflatable Aerodynamic Decelerator (HIAD) have demonstrated the capability of transporting the equivalent science payloads of blunt body rigid aeroshells, while using a significantly smaller diameter when stowed within a launch vehicle. While DEVs' increased energy dissipation for less mass is an attractive feature, their ability to contract and expand would require advancements in the current state-of-the-art guidance and control (G&C) architectures used by traditional rigid vehicles. Pterodactyl, a project funded by NASA's Space Technology Mission Directorate (STMD), aims to provide feasible integrated G&C solutions for DEVs, complete with optimized vehicle designs and packaging analyses. Structural and aerodynamic analyses for the explored control systems suggested a need for a bank angle guidance algorithm, a heritage guidance approach that has been used in many entry precision targeting vehicles, as well as an additional need for the development of a non-bank angle guidance. For this reason, Pterodactyl will consider four different G&C configurations during its design phase: i) a reaction control system for bank (sigma) control, ii) a mass movement system for angle of attack (alpha) sideslip (beta) control, iii) flaps for alpha - beta control, and iv) flaps for sigma control. To increase the applicability of each proposed integrated G&C architecture, an 11 km/s lunar return demonstration mission is selected to stress the developed technology capability. The Lifting Nano-ADEPT (LNA) vehicle is chosen as the DEV to demonstrate the integrated solutions. This paper will detail the trajectory design for a lunar return mission, using the validated bank control guidance algorithm Fully Numerical Predictor-Corrector Entry Guidance (FNPEG) and a newly developed guidance algorithm: FNPEG Uncoupled Range Control (URC). FNPEG-URC diverges from traditional bank angle guidances by producing alpha and beta commands to thereby decouple downrange and crossrange control. This presentation will discuss the development and overall performance of FNPEG and FNPEG-URC for each of the four G&C configurations. Successful G&C configurations are defined as those that can deliver payloads to the intended descent and landing site while abiding by trajectory constraints in the face of dispersions.

Johnson, Breanna

AERACEPT (Aerosol Rapid Analysis Combined Entry Probe/sonde Technology): Enabling Technology for Planetary Atmospheric Science Probes

Aerosols –clouds, hazes, and dusts –are a key part of planetary mass and energy balance, but difficult to study remotely. Current technology limits in situ measurements to once-in-a-lifetime flagship missions, which is not enough to characterize such highly dynamic systems. AERACEPT (AErosol Rapid Analysis Combined Entry Probe/sonde Technology) is an early-stage technology allowing asingle aeroshell body toact as both anentry vehicle and aerosol-samplingpassivedescent sonde, using the aeroshell’sown velocityto drive aerosol capture and separationthrough a series of embedded inlets.It takes advantage ofrecently developed thermal protection materials (3D-CC and 3MDCP)in combination withheritage aerosol sampling technologies fromboth planetary and airborne science (high-speed inlets and particle separation). By eliminating the need for heat shield separation, deployable parachutes, ordescent control, AERACEPT reducesthe mass, volume, and complexity ofplanetary aerosol sampling. Verifying AERACEPT’s performance involves modeling interdependencies between the size and geometry of the sampling inlets, the material response of the hypersonic phase of entry, the thermal conditions throughout the probe’s descent, the subsonic flow and particle sampling efficiency, the needed amount of sample, andthe cadence at which the sample can be analyzed. AERACEPT’s current predictions, using the Nephele Venus cloud mission concept (sampling between 63km to 39km, all subsonic) indicates AERACEPT can obtain >20 μL of particle material (roughly 10x the limit of detection) from droplets larger than 0.2 μm, with sample heating limited to <15 K above ambient. Validation testing for the thermal material response model has recently been performed at the UIUC Plasmatron facility, and for the flow and particle capture models is planned for this fall at the Ames Fluid Mechanics Laboratory.

AERACEPT

AERACEPT (Aerosol Rapid Analysis Combined Entry Probe/sonde Technology): Enabling Technology for Missions to the Venus Clouds

AERACEPT (AErosol Rapid Analysis Combined Entry Probe/sonde Technology) is an early-stage technology allowing a single aeroshell body to act as both an entry vehicle and aerosol-sampling passive descent sonde. AERACEPT does not require heat shield separation, deployable parachutes, or descent control, thus reducing the mass, volume, and complexity of planetary aerosol sampling. AERACEPT is particularly well suited for a Venus mission, where the particles of greatest interest are within the subsonic descent regime. AERACEPT uses the aeroshell’s own velocity to drive aerosol capture and separation through a series of embedded inlets. It takes advantage of recently developed thermal protection materials (3D-CC and HEEET) in combination with heritage aerosol sampling technologies from both planetary and airborne science (high-speed inlets and particle separation). The trade space for a given descent trajectory includes the particle capture efficiency for a given size, the bias introduced in the sampled particle size and concentration distributions, and the thermal alteration experienced by the particles during their brief exposure to the internal flow environment. AERACEPT is included in the Nephele mission concept study for a small spacecraft targeting the Venus middle and lower cloud layers. Nephele complements larger missions targeting Venus atmospheric gas analysis, such as DAVINCI and Venera-D, by specifically targeting cloud and haze particles. Because of the short lifetime of the probe in the lower atmosphere, Nephele requires a fast cadence of analysis of the captured particles, and includes the VOLTR dual optical spectrometer (SERS/LIBS) as part of its notional payload. Preliminary modeling based on the Nephele trajectory at 63 km to 39 km indicates AERACEPT can limit sample heating to 30-60 K above ambient. A modified particle tracking model has been implemented to estimate capture efficiency of particles larger than 0.1 µm and total sample volume as part of an inlet and interal flow path geometry trade study. Further modeling and empirical testing is underway to improve these estimates.

AERACEPT

Folding Elastic Thermal Surface - FETS

The FETS is a light and compact thermal surface (sun shade, IR thermal shield, cover, and/or deployable radiator) that is mounted on a set of offset tape-spring hinges. The thermal surface is constrained during launch and activated in space by a thermomechanical latch such as a wax actuator. An application-specific embodiment of this technology developed for the MATMOS (Mars Atmospheric Trace Molecule Occultation Spectrometer) project serves as a deployable cover and thermal shield for its passive cooler. The FETS fits compactly against the instrument within the constrained launch envelope, and then unfolds into a larger area once in space. In this application, the FETS protects the passive cooler from thermal damage and contamination during ground operations, launch, and during orbit insertion. Once unfolded or deployed, the FETS serves as a heat shield, intercepting parasitic heat loads by blocking the passive cooler s view of the warm spacecraft. The technology significantly enhances the capabilities of instruments requiring either active or passive cooling of optical detectors. This can be particularly important for instruments where performance is limited by the available radiator area. Examples would be IR optical instruments on CubeSATs or those launched as hosted payloads because radiator area is limited and views are often undesirable. As a deployable radiator, the panels making up the FETS are linked thermally by thermal straps and heat pipes; the structural support and deployment energy is provided using tape-spring hinges. The FETS is a novel combination of existing technologies. Prior art for deployable heat shields uses rotating hinges that typically must be lubricated to avoid cold welding or static friction. By using tape-spring hinges, the FETS avoids the need for lubricants by avoiding friction altogether. This also eliminates the potential for contamination of nearby cooled optics by outgassing lubricants. Furthermore, the tape-spring design of the FETS is also self-locking so the panels stay in a rigid and extended configuration after deployment. This unexpected benefit makes the tape-spring hinge design of the FETS a light, simple, reliable, compact, non-outgassing hinge, spring, and latch. While tape-spring hinges are not novel, they have never been used to deploy passive unfolding thermal surfaces (radiator panels, covers, sun shades, or IR thermal shields). Furthermore, because this technology is compact, it has minimal impact on the launch envelope and mass specifications. FETS enhances the performance of hosted payload instruments where the science data is limited by dark noise. Incorporating FETS into a thermal control system increases radiator area, which lowers the optical detector temperature. This results in higher SNR (signal-to-noise ratio) and improved science data.

Urquiza, Eugenio

Flexible Ablators: Applications and Arcjet Testing

Flexible ablators were conceived in 2009 to meet the technology pull for large, human Mars Exploration Class, 23 m diameter hypersonic inflatable aerodynamic decelerators. As described elsewhere, they have been recently undergoing initial technical readiness (TRL) advancement by NASA. The performance limits of flexible ablators in terms of maximum heat rates, pressure and shear remain to be defined. Further, it is hoped that this emerging technology will vastly expand the capability of future NASA missions involving atmospheric entry systems. This paper considers four topics of relevance to flexible ablators: (1) Their potential applications to near/far term human and robotic missions (2) Brief consideration of the balance between heat shield diameter, flexible ablator performance limits, entry vehicle controllability and aft-body shear layer impingement of interest to designers of very large entry vehicles, (3) The approach for developing bonding processes of flexible ablators for use on rigid entry bodies and (4) Design of large arcjet test articles that will enable the testing of flexible ablators in flight-like, combined environments (heat flux, pressure, shear and structural tensile loading). Based on a review of thermal protection system performance requirements for future entry vehicles, it is concluded that flexible ablators have broad applications to conventional, rigid entry body systems and are enabling to large deployable (both inflatable and mechanical) heat shields. Because of the game-changing nature of flexible ablators, it appears that NASA's Office of the Chief Technologist (OCT) will fund a focused, 3-year TRL advancement of the new materials capable of performance in heat fluxes in the range of 200-600 W/sq. cm. This support will enable the manufacture and use of the large-scale arcjet test designs that will be a key element of this OCT funded activity.

Thermal Protection

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material

Integrated Thermal Protection Systems and Heat Resistant Structures

In the early stages of NASA's Exploration Initiative, Snecma Propulsion Solide was funded under the Exploration Systems Research & Technology program to develop a CMC heatshield, a deployable decelerator, and an ablative heat shield for reentry vehicles. Due to changes within NASA's Exploration Initiative, this task was cancelled in early FY06. This paper will give an overview of the work that was accomplished prior to cancellation. The Snecma team consisted of MT Aerospace, Germany, and Materials Research & Design (MR&D), NASA Langley, NASA Dryden, and NASA Ames in the United States. An Apollo-type capsule was chosen as the reference vehicle for the work. NASA Langley generated the trajectory and aerothermal loads. Snecma and MT Aerospace began the design of a ceramic aft heatshield (CAS) utilizing C/SiC panels as the capsule heatshield. MR&D led the design of a C/SiC deployable decelerator, NASA Ames led the characterization of several ablators, NASA Dryden led the development of a heath management system and the high temperature structures testing, and NASA Langley led the insulation characterization. Though the task was pre-maturely cancelled, a significant quantity of work was accomplished.

Pichon, Thierry