Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diesel injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The effect of insulated combustion chamber surfaces on direct-injected diesel engine performance, emissions, and combustion

The combustion chamber of a single-cylinder, direct-injected diesel engine was insulated with ceramic coatings to determine the effect of low heat rejection (LHR) operation on engine performance, emissions, and combustion. In comparison to the baseline cooled engine, the LHR engine had lower thermal efficiency, with higher smoke, particulate, and full load carbon monoxide emissions. The unburned hydrocarbon emissions were reduced across the load range. The nitrous oxide emissions increased at some part-load conditions and were reduced slightly at full loads. The poor LHR engine performance was attributed to degraded combustion characterized by less premixed burning, lower heat release rates, and longer combustion duration compared to the baseline cooled engine.

Dickey, Daniel W.↗
NASA NTRS1989

Two-dimensional analysis of two-phase reacting flow in a firing direct-injection diesel engine

The flow field, spray penetration, and combustion in two-stroke diesel engines are described. Fuel injection begins at 345 degrees after top dead center (ATDC) and n-dodecane is used as the liquid fuel. Arrhenius kinetics is used to calculate the reaction rate term in the quasi-global combustion model. When the temperature, fuel, and oxygen mass fraction are within suitable flammability limits, combustion begins spontaneously. No spark is necessary to ignite a localized high temperature region. Compression is sufficient to increase the gaseous phase temperature to a point where spontaneous chemical reactions occur. Results are described for a swirl angle of 22.5 degrees.

Nguyen, H. Lee↗
NASA NTRS1983

Baseline performance and emissions data for a single-cylinder, direct-injected diesel engine

Comprehensive fuel consumption, mean effective cylinder pressure, and emission test results for a supercharged, single-cylinder, direct-injected, four-stroke-cycle, diesel test engine are documented. Inlet air-to-exhaust pressure ratios were varied from 1.25 to 3.35 in order to establish the potential effects of turbocharging techniques on engine performance. Inlet air temperatures and pressures were adjusted from 34 to 107 C and from 193 to 414 kPa to determine the effects on engine performance and emissions. Engine output ranged from 300 to 2100 kPa (brake mean effective pressure) in the speed range of 1000 to 3000 rpm. Gaseous and particulate emission rates were measured. Real-time values of engine friction and pumping loop losses were measured independently and compared with motored engine values.

Dezelick, R. A.↗
NASA NTRS1988

Liquid sprays and flow studies in the direct-injection diesel engine under motored conditions

A two dimensional, implicit finite difference method of the control volume variety, a two equation model of turbulence, and a discrete droplet model were used to study the flow field, turbulence levels, fuel penetration, vaporization, and mixing in diesel engine environments. The model was also used to study the effects of engine speed, injection angle, spray cone angle, droplet distribution, and intake swirl angle on the flow field, spray penetration and vaporization, and turbulence in motored two-stroke diesel engines. It is shown that there are optimum conditions for injection, which depend on droplet distribution, swirl, spray cone angle, and injection angle. The optimum conditions result in good spray penetration and vaporization and in good fuel mixing. The calculation presented clearly indicates that internal combustion engine models can be used to assess, at least qualitatively, the effects of injection characteristics and engine operating conditions on the flow field and on the spray penetration and vaporization in diesel engines.

Nguyen, Hung Lee↗
NASA NTRS1926

The Fundamental Principles of High-speed Semi-diesel Engines. Part I: a General Discussion of the Subject of Fuel Injection in Diesel Engines and Detailed Descriptions of Many Types of Injection Nozzles

Three questions relating to the technical progress in the utilization of heavy oils are discussed. The first question considers solid injection in high-speed automobile engines, the second concerns the development of the hot-bulb engine, and the third question relates to the need for a more thorough investigation of the processes on which the formatation of combustible, rapidly-burning mixtures depend.

NOZZLES, FUEL - PEUGEOT-TARTRAIS↗
DOE OSTI2025

Mapping ammonia-diesel combustion on a single-cylinder 107 mm bore diesel engine retrofitted for ammonia port-fuel injection

Ammonia is garnering significant interest from the international maritime sector as an alternative fuel. It is attractive as a hydrogen carrier and as a fuel because it has a higher volumetric energy density compared with gaseous or liquid hydrogen, making it easier to store and transport without requiring high pressures or cryogenic storage. Ammonia has significant toxicity concerns, but safe handling procedures have already been established because it is one of the most widely produced chemicals worldwide for use as a fertilizer. Barriers to consuming NH 3 as a fuel in engines include (1) less favorable ignition energy and flame speed compared with conventional fuels; (2) emissions challenges, including potentially high NH 3 , NO X , and N 2 O emissions; and (3) fuel delivery and handling challenges. Although NH 3 has been used to fuel compression-ignition marine engines in limited demonstration projects, technical barriers still exist. The use of NH 3 as a fuel in smaller-bore, high-speed auxiliary engines for large vessels and for smaller inland and coastal marine applications remains unaddressed. This work investigates a late-injection diesel pilot ignition dual-fuel NH 3 strategy using a single-cylinder, high-speed Cummins four-stroke diesel engine platform with a 107 mm bore and 1.1 L displacement per cylinder. The engine was modified for port fuel injection of heated gaseous anhydrous NH 3 . The diesel fuel injection system and the combustion geometry were unmodified to represent a retrofit application, which would minimize additional hardware to maximize diesel fuel displacement with NH 3 . Furthermore, the results show the applicability of a late injection diesel pilot strategy to overcome the challenging fuel properties of NH 3 over the engine operating envelope. Mapping results focusing on emissions are presented, and comparisons are made to a conventional diesel combustion baseline.

Ship engines↗
DOE OSTI2025

Dual-Fuel Ammonia Equivalence Ratio Sweep Data

Ammonia (NH3) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2,eq and thermal efficiency benefits both E-pilot and L-pilot injection strategy cases compared with CDC at a λ of 1.4. The indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for L-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions. This dataset includes the raw experimental data and documentation of the experiment conditions and methods.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1983

Characterization of a high-pressure diesel fuel injection system as a control technology option to improve engine performance and reduce exhaust emissions

Test results from a high pressure electronically controlled fuel injection system are compared with a commercial mechanical injection system on a single cylinder, diesel test engine using an inlet boost pressure of 2.6:1. The electronic fuel injection system achieved high pressure by means of a fluid intensifier with peak injection pressures of 47 to 69 MPa. Reduced exhaust emissions were demonstrated with an increasing rate of injection followed by a fast cutoff of injection. The reduction in emissions is more responsive to the rate of injection and injection timing than to high peak injection pressure.

Mcfadden, J. J.↗
DOE OSTI2025

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗
DOE OSTI2025

Experimental investigation of air-fuel equivalence ratio effects on advanced dual-fuel ammonia/diesel combustion on a single-cylinder medium-duty diesel engine at high load

Ammonia (NH 3 ) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH 3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH 3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N 2 O emissions was identified. The results indicated an optimal balance between CO 2,eq and thermal efficiency benefits both E-pilot and l-pilot injection strategy cases compared with CDC at a λ of 1.4. In conclusion, the indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for l-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions.

Ammonia↗
DOE OSTI2020

Development and Validation of Physics-Based Sub-Models of High-Pressure Supercritical Fuel Injection at Diesel Conditions Insert

The project sought to develop and validate accurate, physics-based, numerical submodels and implement them in computational fluid dynamics (CFD) software codes to enable accurate predictions of diesel sprays at pressures higher than the current systems. The combined experimental-computational effort has four main objectives: (1) acquire spatially and temporally resolved scalar measurements of fuel-oxidizer mixing in the near field of the fuel jet, (2) develop software modules to calculate thermo-physical properties of diesel surrogates and their mixtures with oxidizer of interest in real-gas operating regime, (3) integrate the real-fluid model into a commercial and an open-source CFD code to simulate fuel-air mixing in high-pressure diesel sprays, and (4) assess the robustness, accuracy, and uncertainty of the integrated CFD solvers in computing diesel sprays. Project accomplishments are consistent with the original goals of the project. Although we acquired spatially and temporally resolved scalar measurements, they were limited to refractive index difference and not to thermodynamic properties such as temperature and equivalence ratio. However, we successfully developed the theoretical background needed to acquire such measurements at diesel conditions and demonstrated the capability of the RSD for scalar measurements in a canonical turbulent jet flow replicating features of the diesel jet. Additional work will be needed to implement these procedures at high-pressure, high-temperature engine-like conditions of the CPFR. Mainly, we did not anticipate the need to find the liquid boundary and its statistical features or the state relationships between refractive index and thermodynamic properties, assuming the widely known Dale-Gladstone equation would suffice. Still, efforts devoted to these tasks were essential to fulfil the goals of the project and serves as the foundation on which many of the conclusions and key contributions of this project are based. Further assessment and application of the developed CFD codes is recommended to fully realize the benefits of this research.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1936

Ignition and Flame Development in the Case of Diesel Fuel Injection

To investigate the process of ignition and combustion in the case of spray injection into heated air, a new form of apparatus is developed and the tests carried out with it described. Photographs of the spray before and after ignition are obtained at frequencies of 500 pictures per second. Pressures and temperatures are simultaneously recorded on oscillograms. Information on the initial conditions, ignition time lag, period of complete combustion, place where ignition starts, and general course of the combustion is obtained.

Holfelder, Otto↗
DOE OSTI2021

Investigation of post-injection strategies for diesel engine Catalyst Heating Operation using a vapor-liquid-equilibrium-based spray model

Most multidimensional engine simulations spend much time solving for non-equilibrium spray dynamics (atomization, collision, vaporization). However, their accuracy is limited by significant grid dependency, and the need for extensive calibration. This is critical for modeling cold-start diesel fuel post injections, which occur at low temperatures and pressures, far from typical model validation ranges. At the same time, resolving micron-scale spray phenomena would render full Eulerian multiphase calculations prohibitive. In this study, an improved phase equilibrium based approach was implemented and assessed for simulating diesel catalyst heating operation strategies. A phase equilibrium solver based on the model by Yue and Reitz [1] was implemented: a fully multiphase CFD solver is employed with an engineering-size engine grid, and fuel injection is modeled using the standard Lagrangian parcels approach. Mass and energy from the liquid parcels are released to the Eulerian multiphase mixture according to an equilibrium-based liquid jet model. An improved phase equilibrium solver was developed to handle large real-gas mixtures such as those from accurate chemical kinetics mechanisms. The liquid-jet model was improved such that momentum transfer to the Eulerian solver better reproduces the physical spray jet structure. Validation of liquid/vapor penetration predictions showed that the model yields accurate results with very limited tuning and low sensitivity to the few calibration constants. In-cylinder simulations of diesel catalyst heating operation strategies showed that capturing spray structure is paramount when short, transient injection pulses and low temperatures are present. Furthermore, the EP model provides improved predictions of post-injection spray structure and ignitability, while conventional spray modeling does not capture the increase of liquid penetration during the expansion stroke. Finally, the only important EP model calibration constant, Cliq, does not affect momentum transfer, but it changes the local charge cooling distribution through the local energy transfer, which makes it candidate to additional research. The results confirm that non-equilibrium spray processes do not need to be resolved in engineering simulations of high-pressure diesel sprays.

42 ENGINEERING↗