Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dynamic Link Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

Truncated ARQ Statistical Link Analysis for Dynamic Links

The future deep space links are migrating towards higher frequency bands such as Ka band and optical. These links are susceptible to non Gaussian and non linear effects such as atmospheric turbulence, scintillation, antenna mis-pointing, jitter, etc. These dynamic links thus will experience various degrees of fading loss, and some of these link disruptions cannot be effectively mitigated by forward error correction coding and/or interleaving. One effective way to ensure reliable communication is by using Automatic Repeat Request (ARQ) protocol, where the receiver acknowledges to the transmitter whether or not a data unit is successfully received. If a data unit is not successfully received (such as after a pre-set time-out), the transmitter would then re-transmit the lost data unit to the receiver. In a previous paper, we derived a statistical link analysis method of finding the optimal operating Signal-to-Noise Ratio (SNR) and estimating the latency of an ARQ scheme. In a more recent paper, we demonstrated the above method using the SNR distribution constructed from the Ka-band (32 GHz) flight data. To simplify the discussion, we considered the academic approach that the ARQ scheme allows for an infinite number of retransmissions. In this paper, we consider the more practical case of a truncated ARQ scheme, where there is a limit on the number of retransmissions. We derive the error probability, the optimal SNR setting, and the latency statistics of the correctly received frames of the truncated ARQ schemes. We first discuss the truncated ARQ link analysis principles using the Gaussian assumption for SNR distribution with a large variance. Next, we demonstrate the statistical truncated ARQ link analysis using the SNR distribution constructed from the Ka-band flight data. The results in this paper can be applied in the design of reliable communication systems such as the Consultative Committee for Space Data System (CCSDS) File Transfer Protocol (CFTP) and the Delay Tolerant Network (DTN).

Morabito, David↗
NASA NTRS2017

Demonstrating High-Accuracy Orbital Access Using Open-Source Tools

Orbit propagation is fundamental to almost every space-based analysis. Currently, many system analysts use commercial software to predict the future positions of orbiting satellites. This is one of many capabilities that can replicated, with great accuracy, without using expensive, proprietary software. NASAs SCaN (Space Communication and Navigation) Center for Engineering, Networks, Integration, and Communications (SCENIC) project plans to provide its analysis capabilities using a combination of internal and open-source software, allowing for a much greater measure of customization and flexibility, while reducing recurring software license costs. MATLAB and the open-source Orbit Determination Toolbox created by Goddard Space Flight Center (GSFC) were utilized to develop tools with the capability to propagate orbits, perform line-of-sight (LOS) availability analyses, and visualize the results. The developed programs are modular and can be applied for mission planning and viability analysis in a variety of Solar System applications. The tools can perform 2 and N-body orbit propagation, find inter-satellite and satellite to ground station LOS access (accounting for intermediate oblate spheroid body blocking, geometric restrictions of the antenna field-of-view (FOV), and relativistic corrections), and create animations of planetary movement, satellite orbits, and LOS accesses. The code is the basis for SCENICs broad analysis capabilities including dynamic link analysis, dilution-of-precision navigation analysis, and orbital availability calculations.

propagation↗
NASA NTRS2011

Link Analysis in the Mission Planning Lab

The legacy communications link analysis software currently used at Wallops Flight Facility involves processes that are different for command destruct, radar, and telemetry. There is a clear advantage to developing an easy-to-use tool that combines all the processes in one application. Link Analysis in the Mission Planning Lab (MPL) uses custom software and algorithms integrated with Analytical Graphics Inc. Satellite Toolkit (AGI STK). The MPL link analysis tool uses pre/post-mission data to conduct a dynamic link analysis between ground assets and the launch vehicle. Just as the legacy methods do, the MPL link analysis tool calculates signal strength and signal- to-noise according to the accepted processes for command destruct, radar, and telemetry assets. Graphs and other custom data are generated rapidly in formats for reports and presentations. STK is used for analysis as well as to depict plume angles and antenna gain patterns in 3D. The MPL has developed two interfaces with the STK software (see figure). The first interface is an HTML utility, which was developed in Visual Basic to enhance analysis for plume modeling and to offer a more user friendly, flexible tool. A graphical user interface (GUI) written in MATLAB (see figure upper right-hand corner) is also used to quickly depict link budget information for multiple ground assets. This new method yields a dramatic decrease in the time it takes to provide launch managers with the required link budgets to make critical pre-mission decisions. The software code used for these two custom utilities is a product of NASA's MPL.

McCarthy, Jessica A.↗
NASA NTRS2014

Comm for Small Sats: The Lunar Atmosphere and Dust Environment Explorer (LADEE) Communications Subsystem

September 6, 2013 through April 21, 2014 marked the mission lifecycle of the highly successful LADEE (Lunar Atmosphere and Dust Environment Explorer) mission that orbited the moon to gather detailed information about the thin lunar atmosphere. This paper will address the development, risks, and lessons learned regarding the specification, selection, and deployment of LADEE's unique Radio Frequency based communications subsystem and supporting tools. This includes the Electronic Ground Support Equipment (EGSE), test regimes, and RF dynamic link analysis environment developed to meet mission requirements for small, flexible, low cost, high performance, fast turnaround, and reusable spacecraft communication capabilities with easy and reliable application to future similar low cost small satellite missions over widely varying needs for communications and communications system complexity. LADEE communication subsystem key components, architecture, and mission performance will be reviewed toward applicability for future mission planning, design, and utilization.

transponder↗
DOE OSTI2026

A Kinetic Model-Driven Techno-Economic Analysis of Plastic Pyrolysis: Linking Process Dynamics to Economic Viability

This study employs a kinetic model integrated into Aspen Plus to predict pyrolysis product distribution under various conditions. A techno-economic assessment calculated the minimum selling price (MSP) of pyrolysis oil under different operating conditions for the baseline capacity of 100 kta, and across eight processing capacities ranging from 30 to 150 kta. The lowest MSP under the baseline capacity is estimated at $\$$420/ton, which is 33% lower than the 2023 average US crude oil price ($\$$74.6/bbl, equivalent to $\$$634/ton based on the density of pyrolysis oil). Under Monte Carlo simulation, accounting for variability in key economic and technical parameters, the mean MSP is estimated at $\$$1137/ton. The economic viability depends on feedstock price remaining below $\$$320/ton, defining the break-even feedstock price threshold. Sensitivity analysis further identifies capital investment and transportation cost as key economic drivers. Capacities beyond 90 kta show limited economies of scale benefits. Reducing product storage time cuts capital costs by 7% but raises operational risk. Uncertainty analysis suggests the economic feasibility of pyrolysis oil is unlikely to compete with crude oil without policy incentives.

petrochemicals↗
NASA NTRS1990

Dynamic Analysis and Control of Lightweight Manipulators with Flexible Parallel Link Mechanisms

The objective is the theoretical analysis and the experimental verification of dynamics and control of a two link flexible manipulator with a flexible parallel link mechanism. Nonlinear equations of motion of the lightweight manipulator are derived by the Lagrangian method in symbolic form to better understand the structure of the dynamic model. The resulting equation of motion have a structure which is useful to reduce the number of terms calculated, to check correctness, or to extend the model to higher order. A manipulator with a flexible parallel link mechanism is a constrained dynamic system whose equations are sensitive to numerical integration error. This constrained system is solved using singular value decomposition of the constraint Jacobian matrix. Elastic motion is expressed by the assumed mode method. Mode shape functions of each link are chosen using the load interfaced component mode synthesis. The discrepancies between the analytical model and the experiment are explained using a simplified and a detailed finite element model.

Lee, Jeh Won↗
NASA NTRS1991

Dynamic analysis and control of lightweight manipulators with flexible parallel link mechanisms

The flexible parallel link mechanism is designed for increased rigidity to sustain the buckling when it carries a heavy payload. Compared to a one link flexible manipulator, a two link flexible manipulator, especially the flexible parallel mechanism, has more complicated characteristics in dynamics and control. The objective of this research is the theoretical analysis and the experimental verification of dynamics and control of a two link flexible manipulator with a flexible parallel link mechanism. Nonlinear equations of motion of the lightweight manipulator are derived by the Lagrangian method in symbolic form to better understand the structure of the dynamic model. A manipulator with a flexible parallel link mechanism is a constrained dynamic system whose equations are sensitive to numerical integration error. This constrained system is solved using singular value decomposition of the constraint Jacobian matrix. The discrepancies between the analytical model and the experiment are explained using a simplified and a detailed finite element model. The step response of the analytical model and the TREETOPS model match each other well. The nonlinear dynamics is studied using a sinusoidal excitation. The actuator dynamic effect on a flexible robot was investigated. The effects are explained by the root loci and the Bode plot theoretically and experimentally. For the base performance for the advanced control scheme, a simple decoupled feedback scheme is applied.

Lee, Jeh Won↗
NASA NTRS1989

The coupling effects of kinematics and flexibility on the Lagrangian dynamic formulation of open chain deformable links

A nonlinear Lagrangian formulation for the spatial kinematic and dynamic analysis of open chain deformable links consisting of cylindrical joints that connect pairs of flexible links is developed. The special cases of revolute or prismatic joint can also be obtained from the kinematic equations. The kinematic equations are described using a 4x4 matrix method. The configuration of each deformable link in the open loop kinematic chain is identified using a coupled set of relative joint variables, constant geometric parameters, and elastic coordinates. The elastic coordinates define the link deformation with respect to a selected joint coordinate system that is consistent with the kinematic constraints on the boundary of the deformable link. These coordinates can be introduced using approximation techniques such as Rayleigh-Ritz method, finite element technique or any other desired approach. The large relative motion between two neighboring links are defined by a set of joint coordinates which describes the large relative translational and rotational motion between two neighboring joint coordinate systems. The origin of these coordinate systems are rigidly attached to the neighboring links at the joint definition points along the axis of motion.

Changizi, Koorosh↗
NASA NTRS2006

LAD-C: A large area debris collector on the ISS

The Large Area Debris Collector (LAD-C) is a 10 sq m aerogel and acoustic sensor system under development by the U.S. Naval Research Laboratory (NRL) with main collaboration from the NASA Orbital Debris Program Office at Johnson Space Center, JAXA Institute of Space and Astronautical Science (ISAS), Chiba University (Japan), ESA Space Debris Office, University of California at Berkeley, and University of Kent at Canterbury (UK). The U.S. Department of Defense (DoD) Space Test Program (STP) has assumed the responsibility for having the system manifested and deployed on the International Space Station (ISS), and then having it retrieved and returned to Earth after one to two years. LAD-C will attempt to utilize the ISS as a scientific platform to characterize the near-Earth meteoroid and orbital debris environment in the size regime where little data exist. In addition to meteoroid and orbital debris sample return, the acoustic sensors will record impact time, location, signal strength, and acoustic waveform data of the largest collected samples. A good time-dependent meteoroid and orbital debris flux estimate can be derived. Analysis of the data will also enable potential source identification of some of the collected samples. This dynamical link can be combined with laboratory composition analysis of impact residuals extracted from aerogel to further our understanding of orbital debris population, and the sources of meteoroids, asteroids and comets.

Liou, J.-C.↗
DOE OSTI2026

Feedback and Oscillations: Constructing Feedback Systems for Root Cause Analysis of Oscillations in Power Grids

Dynamic phenomena linked to inverter-based resources (IBRs) have gained global attention. Several IBR-induced dynamics have caused bulk power system-connected wind or solar power plants to trip, and some have even led to widespread outages. In addition, many oscillations have been observed involving IBR power plants. In 2023, the IEEE Power & Energy Society (PES) IBR Subsynchronous Oscillations (SSO) task force published a journal article, “Real-World Subsynchronous Oscillation Events in Power Grids With High Penetrations of Inverter-Based Resources,” in which 19 IBR oscillation events were examined for their causation. Earlier in 2020, another PES task force article, “Definition and Classification of Power System Stability-Revisited & Extended,” authored by prominent academics, introduced converter-driven stability as a new category of stability. The international power grid industry community also took action by publishing the CIGRE Green Book, Power System Dynamic Modelling and Analysis in Evolving Networks (led by Babak Badrzadeh and Zia Emin) in 2024. In August 2024, the Energy Systems Integration Group (ESIG) released a practical guide led by Nick Miller, “Diagnosis and Mitigation of Observed Oscillations in IBR-Dominant Power System: A Practical Guide.” The goal of the guide is to assist practicing engineers in making initial judgments and conducting detailed analyses about oscillations. Finally, when addressing the classification of stability and oscillations, the guide emphasizes a causality-based taxonomy for grouping, such as voltage control-induced oscillations, synchronization-induced oscillations, and frequency or active power control-induced oscillations.

Fan, Lingling [Univ. of South Florida, Tampa, FL (↗
DOE OSTI2021

Dynamic Linking of Upstream Energy and Freight Demands for Bio and Fossil Energy Pathways in the Global Change Analysis Model

Comprehensive study of the environmental impacts associated with demand for an energy resource or carrier in any one sector requires a full consideration of the direct and indirect impacts on the rest of the regional and global energy system. It is important to consider the energy that is consumed in producing primary energy resources and energy consumed in transporting these energy resources internationally and domestically in order to produce a complete picture of these impacts. Biofuels are especially complex since they have feedbacks not just to the energy system but also to regional and global crop markets. Different modeling and analysis strategies have been applied to consider these impacts, which occur “upstream” of final energy consumption, with some success. Traditional life cycle models allow for rich technological detail in linking upstream impacts of energy demand with downstream final consumption; however, they cannot by themselves represent dynamic economic feedbacks across multiple sectors and regions over time. Computable general equilibrium (CGE) modeling does account for economic feedback among all sectors and regions; however, CGE modeling does not lend itself to physical representation of technological detail. Partial equilibrium (PE) modeling is a heterogeneous category describing economic models that focus on a subset of the economy, and they differ in coverage and ease in incorporating more sectors and economic links. In this study, we present a strategy for dynamically including the direct and indirect impacts of energy demand with physical and technology detail by explicitly adding these upstream energy and transportation links to GCAM, a PE model of global energy, land use, and emissions. We incorporate the following inter-sectoral linkages: energy inputs to crop production, energy inputs to fossil resource production, and freight transport requirements of energy and agricultural commodities. We assess the implications of explicitly including these links by measuring the global impacts of increased corn ethanol demand in the United States with and without these links included. Although the net global impact of the upstream links on energy and emissions are relatively modest in the scenarios we studied, the inclusion of these links illustrates interesting trade-offs in energy and transportation demand among fossil fuel and agriculture sectors. These sectoral interactions suggest that this level of modeling detail could be important in evaluating future analytical questions.

Sampedro Martinez de Estivariz, Jon↗
NASA NTRS2000

Supporting Scientific Analysis within Collaborative Problem Solving Environments

Collaborative problem solving environments for scientists should contain the analysis tools the scientists require in addition to the remote collaboration tools used for general communication. Unfortunately, most scientific analysis tools have been designed for a "stand-alone mode" and cannot be easily modified to work well in a collaborative environment. This paper addresses the questions, "What features are desired in a scientific analysis tool contained within a collaborative environment?", "What are the tool design criteria needed to provide these features?", and "What support is required from the architecture to support these design criteria?." First, the features of scientific analysis tools that are important for effective analysis in collaborative environments are listed. Next, several design criteria for developing analysis tools that will provide these features are presented. Then requirements for the architecture to support these design criteria are listed. Sonic proposed architectures for collaborative problem solving environments are reviewed and their capabilities to support the specified design criteria are discussed. A deficiency in the most popular architecture for remote application sharing, the ITU T. 120 architecture, prevents it from supporting highly interactive, dynamic, high resolution graphics. To illustrate that the specified design criteria can provide a highly effective analysis tool within a collaborative problem solving environment, a scientific analysis tool that contains the specified design criteria has been integrated into a collaborative environment and tested for effectiveness. The tests were conducted in collaborations between remote sites in the US and between remote sites on different continents. The tests showed that the tool (a tool for the visual analysis of computer simulations of physics) was highly effective for both synchronous and asynchronous collaborative analyses. The important features provided by the tool (and made possible by the specified design criteria) are: 1. The tool provides highly interactive, dynamic, high resolution, 3D graphics. 2. All remote scientists can view the same dynamic, high resolution, 3D scenes of the analysis as the analysis is being conducted. 3. The responsiveness of the tool is nearly identical to the responsiveness of the tool in a stand-alone mode. 4. The scientists can transfer control of the analysis between themselves. 5. Any analysis session or segment of an analysis session, whether done individually or collaboratively, can be recorded and posted on the Web for other scientists or students to download and play in either a collaborative or individual mode. 6. The scientist or student who downloaded the session can, individually or collaboratively, modify or extend the session with his/her own "what if" analysis of the data and post his/her version of the analysis back onto the Web. 7. The peak network bandwidth used in the collaborative sessions is only 1K bit/second even though the scientists at all sites are viewing high resolution (1280 x 1024 pixels), dynamic, 3D scenes of the analysis. The links between the specified design criteria and these performance features are presented.

Watson, Velvin R.↗
NASA NTRS2019

Space Communications and Navigation (SCaN) Tool Capabilities Updates for Antenna Pattern and Jitter

The ability to accurately simulate the dynamic misalignment of pointing across a communications link is critical to determining the link performance between/across spacecraft and/or ground stations. The communication system antenna pattern and dynamic misalignment are key components to understanding the pointing loss induced on the communications link. Currently, projects performing these analyses use a variety of simulation tools and packages. NASA's Space Communications and Navigation (SCaN) office aims to provide a unified tool set for these functions. However, the analysis tool to calculate antenna patterns is currently static, two-dimensional, and approximated based on limited input. Steps were taken to change the inputs used by the tool to create a more accurate approximation of the antenna's far field pattern as well as create a three-dimensional pattern. An additional tool was also developed to calculate time-dynamic pointing loss from the antenna pattern generated or observed antenna pattern data given dynamic pointing errors.

SCaN↗
NASA NTRS1991

Fiber optic link for millimeter wave communication satellites

An electrically and optically optimized 18.5 to 19.0 GHz short-haul fiber optic (F.O.) link is presented. A theoretical link analysis of gain, system noise contributions, linearity, and dynamic range is shown as well as the corresponding measurements. Results indicate that by employing reactive matching and on-fiber lensing techniques, performance of high-speed F.O. links are still limited by high relative intensity noise levels and the limited frequency response of the laser. Alternative architectures are suggested to counteract these limiting problems of current high speed links.

Polifko, D. M.↗
NASA NTRS2003

Structural Reliability Using Probability Density Estimation Methods Within NESSUS

A reliability analysis studies a mathematical model of a physical system taking into account uncertainties of design variables and common results are estimations of a response density, which also implies estimations of its parameters. Some common density parameters include the mean value, the standard deviation, and specific percentile(s) of the response, which are measures of central tendency, variation, and probability regions, respectively. Reliability analyses are important since the results can lead to different designs by calculating the probability of observing safe responses in each of the proposed designs. All of this is done at the expense of added computational time as compared to a single deterministic analysis which will result in one value of the response out of many that make up the density of the response. Sampling methods, such as monte carlo (MC) and latin hypercube sampling (LHS), can be used to perform reliability analyses and can compute nonlinear response density parameters even if the response is dependent on many random variables. Hence, both methods are very robust; however, they are computationally expensive to use in the estimation of the response density parameters. Both methods are 2 of 13 stochastic methods that are contained within the Numerical Evaluation of Stochastic Structures Under Stress (NESSUS) program. NESSUS is a probabilistic finite element analysis (FEA) program that was developed through funding from NASA Glenn Research Center (GRC). It has the additional capability of being linked to other analysis programs; therefore, probabilistic fluid dynamics, fracture mechanics, and heat transfer are only a few of what is possible with this software. The LHS method is the newest addition to the stochastic methods within NESSUS. Part of this work was to enhance NESSUS with the LHS method. The new LHS module is complete, has been successfully integrated with NESSUS, and been used to study four different test cases that have been proposed by the Society of Automotive Engineers (SAE). The test cases compare different probabilistic methods within NESSUS because it is important that a user can have confidence that estimates of stochastic parameters of a response will be within an acceptable error limit. For each response, the mean, standard deviation, and 0.99 percentile, are repeatedly estimated which allows confidence statements to be made for each parameter estimated, and for each method. Thus, the ability of several stochastic methods to efficiently and accurately estimate density parameters is compared using four valid test cases. While all of the reliability methods used performed quite well, for the new LHS module within NESSUS it was found that it had a lower estimation error than MC when they were used to estimate the mean, standard deviation, and 0.99 percentile of the four different stochastic responses. Also, LHS required a smaller amount of calculations to obtain low error answers with a high amount of confidence than MC. It can therefore be stated that NESSUS is an important reliability tool that has a variety of sound probabilistic methods a user can employ and the newest LHS module is a valuable new enhancement of the program.

Chamis, Chrisos C.↗