Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELASTIC BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Upper limit for the effect of elastic bending stress on the saturation magnetization of L a 0.8 S r 0.2 Mn O 3

In this study, using polarized neutron reflectometry, we measured the influence of elastic bending stress on the magnetization depth profile of a La 0.8 Sr 0.2 MnO 3 (LSMO) epitaxial film grown on a SrTiO 3 substrate. The elastic bending strain of ±0.03% has no obvious effect on the magnetization depth profile at saturation. This result is in stark contrast to that of (La 1-x Pr x )1-yCayMnO 3 (LPCMO) films for which strain of ±0.01% produced dramatic changes in the magnetization profile and Curie temperature. We attribute the difference between the influence of strain on the saturation magnetization in LSMO (weak or none) and LPCMO (strong) to a difference in the ability of LSMO (weak or none) and LPCMO (strong) to phase separate. Our observation provides an upper limit of tuning LSMO saturation magnetization via elastic strain effect.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Photoacoustic elastic bending in thin film—Substrate system

Theoretical model for optically excited two-layer elastic plate, which includes plasmaelastic, thermoelastic, and thermodiffusion mechanisms, is given in order to study the dependence of the photoacoustic (PA) elastic bending signal on the optical, thermal, and elastic properties of thin film—substrate system. Thin film-semiconductor sample (in our case Silicon) is modeled by simultaneous analysis of the plasma, thermal, and elastic wave equations. Multireflection effects in thin film are included in theoretical model and analyzed. Relations for the amplitude and phase of electronic and thermal elastic bending in the optically excited two-layer mechanically-supported circular plate are derived. Theoretical analysis of the thermodiffusion, plasmaelastic, and thermoelastic effects in a sample-gas-microphone photoacoustic detection configuration is given. Two normalization procedures of the photoacoustic elastic bending signal in function of the modulation frequency of the optical excitation are established. Given theoretical model can be used for various photoacoustic detection configurations, for example, in the study of optical, thermal, and elastic properties of the dielectric-semiconductor or metal-semiconductor structure, etc., Theoretical analysis shows that it is possible to develop new noncontact and nondestructive experimental method—PA elastic bending method for thin film study, with possibility to obtain the optical, thermal, and elastic parameters of the film thinner than 1 μm.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Stability of elastic bending and torsion of uniform cantilever rotor blades in hover with variable structural coupling

The stability of elastic flap bending, lead-lag bending, and torsion of uniform, untwisted, cantilever rotor blades without chordwise offsets between the elastic, mass, tension, and areodynamic center axes is investigated for the hovering flight condition. The equations of motion are obtained by simplifying the general, nonlinear, partial differential equations of motion of an elastic rotating cantilever blade. The equations are adapted for a linearized stability analysis in the hovering flight condition by prescribing aerodynamic forces, applying Galerkin's method, and linearizing the resulting ordinary differential equations about the equilibrium operating condition. The aerodynamic forces are obtained from strip theory based on a quasi-steady approximation of two-dimensional unsteady airfoil theory. Six coupled mode shapes, calculated from free vibration about the equilibrium operating condition, are used in the linearized stability analysis. The study emphasizes the effects of two types of structural coupling that strongly influence the stability of hingeless rotor blades. The first structural coupling is the linear coupling between flap and lead-lag bending of the rotor blade. The second structural coupling is a nonlinear coupling between flap bending, lead-lag bending, and torsion deflections. Results are obtained for a wide variety of hingeless rotor configurations and operating conditions in order to provide a reasonably complete picture of hingeless rotor blade stability characteristics.

Hodges, D. H., Roberta.↗
NASA NTRS1974

Nonlinear equations of motion for the elastic bending and torsion of twisted nonuniform rotor blades

The equations of motion are developed by two complementary methods, Hamilton's principle and the Newtonian method. The resulting equations are valid to second order for long, straight, slender, homogeneous, isotropic beams undergoing moderate displacements. The ordering scheme is based on the restriction that squares of the bending slopes, the torsion deformation, and the chord/radius and thickness/radius ratios are negligible with respect to unity. All remaining nonlinear terms are retained. The equations are valid for beams with mass centroid axis and area centroid (tension) axis offsets from the elastic axis, nonuniform mass and stiffness section properties, variable pretwist, and a small precone angle. The strain-displacement relations are developed from an exact transformation between the deformed and undeformed coordinate systems. These nonlinear relations form an important contribution to the final equations. Several nonlinear structural and inertial terms in the final equations are identified that can substantially influence the aeroelastic stability and response of hingeless helicopter rotor blades.

Hodges, D. H.↗
DOE OSTI2019

A surface with stress, extensional elasticity, and bending stiffness

We demonstrate that the surface of a commonly used polydimethylsiloxane formulation (PDMS, Sylgard 184) treated by ultraviolet ozonolysis (UVO) has significant surface stress, considerable extensional elasticity (the “Shuttleworth Effect”), and surface bending elasticity.

Lapinski, Nicole↗
NASA NTRS2014

Blade Displacement Predictions for the Full-Scale UH-60A Airloads Rotor

An unsteady Reynolds-Averaged Navier-Stokes solver for unstructured grids is loosely coupled to a rotorcraft comprehensive code and used to simulate two different test conditions from a wind-tunnel test of a full-scale UH-60A rotor. Performance data and sectional airloads from the simulation are compared with corresponding tunnel data to assess the level of fidelity of the aerodynamic aspects of the simulation. The focus then turns to a comparison of the blade displacements, both rigid (blade root) and elastic. Comparisons of computed root motions are made with data from three independent measurement systems. Finally, comparisons are made between computed elastic bending and elastic twist, and the corresponding measurements obtained from a photogrammetry system. Overall the correlation between computed and measured displacements was good, especially for the root pitch and lag motions and the elastic bending deformation. The correlation of root lead-lag motion and elastic twist deformation was less favorable.

Bledron, Robert T.↗
DOE OSTI2023

An experiment-informed discrete element modelling study of knife milling for flexural biomass feedstocks

A discrete element method (DEM) based approach is used to study the relationships between material attributes (MAs), processing parameters (PPs), and quality attributes (QAs) for the knife milling of maize stalks. An approximate DEM shape model was conceptualized based on real maize stalks and calibrated based on experimental bending test data for flexural properties (elastic bending stiffness, elastic bending angle limit, elastoplastic ratio, etc.). DEM simulations of maize stalk comminution in a Jordan Reduction Solutions (“JRS”) knife mill were performed to investigate the relationships between the MAs (maize stalk size and breakage stress limit), PPs (impeller rotational speed), and QAs (mass throughput and output particle size distribution (PSD)). The DEM results suggest that stalk length has little influence on mass throughput and PSD, whilst stalks with larger cross sections tend to generate larger sizes of milled particles given the same breakage stress limit. Both the DEM and experimental results show that faster impeller rotation (or higher power) does not necessarily generate higher throughput or smaller output PSD, especially for maize stalks of higher breakage stress limit. The correlations between these MAs, PPs and QAs are found highly stochastic, though breakage stress limit dictates mass throughput, regardless of stalk size. The DEM-predicted output particle size tended to match the experimental data with coarse PSDs based on sieve size but showed weakened fidelity with finer material, indicating the potential for further model improvement.

09 BIOMASS FUELS↗
NASA NTRSDate not supplied

Blade Displacement Measurements of a Rotor in Forward Flight in the Langley 14- by 22-Ft Wind Tunnel

Stereo photogrammetry was used to measure the elastic bending and twist of a three-bladed rotor in forward flight in the NASA Langley 14-by 22-Ft Subsonic Wind Tunnel. The rotor was imaged from below by two cameras mounted at windows of a large turntable in the floor of the test section. At each test condition, the turntable and cameras were rotated and the cameras were triggered to allow measurements over a range of blade azimuth angles. Retro-reflective targets were applied along the leading and trailing edges of the lower surface of each blade. Image blur due to blade motion was minimized by illuminating the targets with high-intensity LED flash lamps mounted next to each camera. The cameras were re-calibrated at each angular position of the turntable using the positions in each image of retro-reflective targets on the ceiling of the test section whose spatial coordinates had been very accurately measured. The blade displacement measurements yielded elastic bending and twist along each blade as functions of blade azimuth, thrust coefficient, and advance ratio, all at a constant rotor angle-of-attack. In addition, the measurements produced estimates of the rigid-body blade pitch, flap, and lag angles.

rotor blade displacement↗
NASA NTRSDate not supplied

Blade Displacement Measurements of a Rotor in Forward Flight in the Langley 14-by 22-Foot Wind Tunnel

Stereo photogrammetry was used to measure the elastic bending and twist of a three-bladed rotor in forward flight in the NASA Langley 14-by 22-Ft Subsonic Wind Tunnel. The rotor was imaged from below by two cameras mounted at windows of a large turntable in the floor of the test section. At each test condition, the turntable and cameras were rotated and the cameras were triggered to allow measurements over a range of blade azimuth angles. Retro-reflective targets were applied along the leading and trailing edges of the lower surface of each blade. Image blur due to blade motion was minimized by illuminating the targets with high-intensity LED flash lamps mounted next to each camera. The cameras were re-calibrated at each angular position of the turntable using the positions in each image of retro-reflective targets on the ceiling of the test section whose spatial coordinates had been very accurately measured. The blade displacement measurements yielded elastic bending and twist along each blade as functions of blade azimuth, thrust coefficient, and advance ratio, all at a constant rotor shaft angle. In addition, the measurements produced estimates of the rigid-body blade pitch, flap, and lag angles.

rotor↗
NASA NTRS1990

Bearingless rotor aeromechanical stability measurements and correlations using nonlinear aerodynamics

The aeromechanical stability of a 1/8th Froude scaled bearingless rotor model was investigated experimentally in a wind tunnel. Both shaft-fixed and shaft-free conditions were examined to study the aeroelastic stability of a bearingless rotor without the incorporation of auxiliary dampers. This wind tunnel investigation generated a set of stability data for four different advance ratios, and a wide range of collective pitch settings. Theoretical analysis was performed using the newly developed University of Maryland Advanced Rotorcraft Code (UMARC). For analysis, the blade is modeled as an elastic beam undergoing flap bending, lag bending, elastic twist, and axial deformation. Blade response is calculated using a finite element method in time. Nonlinear aerodynamic effects are included by using a semiempirical stall modeling. The linearized periodic rotor perturbation equations in the nonrotating frame are solved for stability roots using Floquet transition matrix theory, as well as constant coefficient approximation. The predicted results are compared with the experimental data.

Wang, James M.↗
NASA NTRS1991

An aeroelastic analysis with a generalized dynamic wake

An aeroelastic model with generalized dynamic wake is developed for application in the integration of aerodynamic, dynamic, and structural optimization of a rotor blade. The investigation is carried out with special attention to efficiency and accuracy of aeroelastic modeling. Each blade is assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist and axial deflections. The nonuniform blade is discretized into finite beam elements, each of which consists of twelve degrees of freedom. Such important blade design variables as pretwist, and chordwise offsets of the blade center of gravity and of the aerodynamic center from the elastic axis have been included in the analysis. Aerodynamic loads are computed from unsteady blade element theory where the rotor three-dimensional unsteady wake is modeled using a generalized dynamic wake theory. The noncirculatory loads based on unsteady thin airfoil theory are also included.

He, Cheng J.↗
NASA NTRS1993

Finite state aeroelastic model for use in rotor design optimization

In this article, a rotor aeroelastic model based on a newly developed finite state dynamic wake, coupled with blade finite element analysis, is described. The analysis is intended for application in rotor blade design optimization. A coupled simultaneous system of differential equations combining blade structural dynamics and aerodynamics is established in a formulation well-suited for design sensitivity computation. Each blade is assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist, and axial deflections. Aerodynamic loads are computed from unsteady blade element theory where the rotor three-dimensional unsteady wake is described by a generalized dynamic wake model. Correlation of results obtained from the analysis with flight test data is provided to assess model accuracy.

He, Chengjian↗
DOE OSTI2024

A novel technique for minimizing energy functional using neural networks

An energy functional describes the equilibrium state of a system. In this work, we present a novel technique, Functional Optimization using Neural Networks (FONN), for minimizing the system’s energy. FONN utilizes neural networks to process information at discrete grid points, considering their interactions with neighboring grid points, to update the state of the system. The training process involves formulating a loss function based on the system’s energy, and with the help of multiple fine-tuning steps, the method employs a progressive energy reduction technique that decreases the energy in multiple steps. FONN’s effectiveness is demonstrated across various problems, including the minimization of the heat and Lyapunov energy. Furthermore, the paper explores the minimization of the elastic bending energy with an area constraint.

97 MATHEMATICS AND COMPUTING↗