Search NASA⌕ Search

SEARCH · Search NASA

Results for “ELASTIC MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Sub-Micrometer Zeolite Films on Gold-Coated Silicon Wafers with Single-Crystal-Like Dielectric Constant and Elastic Modulus

A low-temperature synthesis coupled with mild activation produces zeolite films exhibiting low dielectric constant (low-k) matching the theoretically predicted and experimentally measured values for single crystals. This synthesis and activation method allows for the fabrication of a device consisting of a b-oriented film of the pure-silica zeolite MFI (silicalite-1) supported on a gold-coated silicon wafer. The zeolite seeds are assembled by a manual assembly process and subjected to optimized secondary growth conditions that do not cause corrosion of the gold underlayer, while strongly promoting in-plane growth. The traditional calcination process is replaced with a non-thermal photochemical activation to ensure preservation of an intact gold layer. The dielectric constant (k), obtained through measurement of electrical capacitance in a metal-insulator-metal configuration, highlights the ultralow k approximate to 1.7 of the synthetized films, which is among the lowest values reported for an MFI film. There is large improvement in elastic modulus of the film (E approximate to 54 GPa) over previous reports, potentially allowing for integration into silicon wafer processing technology.

Tiriolo, Raffaele↗
DOE OSTI2018

Effects of enzymes on elastic modulus of low-density lipoproteins were investigated using atomic force microscopy

Highlights: • The elastic modulus of the enzymatically digested LDL was evaluated using AFM. • The LDL elastic modulus was decreased not by proteases but by phospholipase A{sub 2}. • The LDL size was unaffected by proteases or PLA{sub 2}. Oxidation of low-density lipoproteins (LDLs) induces development of cardiovascular disease. Recently, reports of studies using atomic force microscopy (AFM) have described that the elastic modulus of metal-induced oxidized LDLs is lower than the modulus before oxidation. However, the mechanisms of change of the elastic modulus have not been well investigated. We postulated that disorder of the LDL structure might decrease the elastic modulus. This study measured the elastic modulus of LDLs before and after enzyme treatment with V8 protease, α-chymotrypsin, and phospholipase A{sub 2}. After LDLs were obtained from serum by ultracentrifugation, LDLs or enzyme-treated LDLs were physically absorbed. They were crowded on a mica surface. Although V8 protease and α-chymotrypsin did not induce the elastic modulus change, treatment with PLA{sub 2} decreased the elastic modulus. The LDL particle size did not change during the enzyme treatment. Results suggest that disordering of the lipid structure of the LDL might contribute to the elastic modulus change. Results show that AFM might be a useful tool to evaluate disorders of complex nanoscale particle structures from lipids and proteins such as lipoproteins.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2018

Nanoindentation of high-purity vapor deposited lithium films: The elastic modulus

Nanoindentation has been used to measure the elastic modulus of 5 and 18 μm thick high-purity vapor deposited polycrystalline lithium films at 31 °C. Over indentation depths ranging from 150 to 1100 nm, the modulus is found to vary with film thickness from 9.8 GPa ± 11.9% to 8.2 GPa ± 14.5%. These results are well within the range of lithium's orientation dependent elastic modulus, which spans approximately 3.1 to 21.4 GPa. The measured values may also indicate (111) and (100) texture for the 5 and 18 μm thick films, respectively. The potential effects of pileup and surface contamination are found to be negligible if any at all. Small but discernible changes in damping capability near the free surface may provide insight into the subsurface defect structure and the potential for localized heating. In conclusion, numerous experimental challenges are addressed and key metrics are used to validate the measured elastic modulus.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrode Elastic Modulus as the Dominant Factor in the Capping Effect in Ferroelectric Hafnium Zirconium Oxide Thin Films

The discovery of ferroelectricity in hafnia based thin films has catalyzed significant research focused on understanding the ferroelectric property origins and means to increase stability of the ferroelectric phase. Prior studies have revealed that biaxial tensile stress via an electrode “capping effect” is a suspected ferroelectric phase stabilization mechanism. This effect is commonly reported to stem from a coefficient of thermal expansion (CTE) incongruency between the hafnia and top electrode. Despite reported correlations between ferroelectric phase fraction and electrode CTE, the thick silicon substrate dominates the mechanics and CTE-related stresses, negating any dominant contribution from an electrode CTE mismatch toward the capping effect. In this work, these discrepancies are reconciled, and the origin of these differences deriving from electrode elastic modulus, not CTE, is demonstrated. Pt/M/TaN/Hf 0.5 Zr 0.5 O 2 /TaN/Si devices, where M is platinum, TaN, iridium, tungsten, and ruthenium, were fabricated. Sin 2 (ψ)-based X-ray diffraction measurements of biaxial stress in the HZO layer reveal a strong correlation between biaxial stress, remanent polarization, and electrode elastic modulus. Conversely, a low correlation exists between the electrode CTE, HZO biaxial stress, and remanent polarization. A higher elastic modulus enhances the resistance to electrode elastic deformation, which intensifies the capping effect during crystallization, and culminates in the tandem restriction of out-of-plane hafnia volume expansion and preferential orientation of the polar c-axis normal to the plane. These behaviors concomitantly increase the ferroelectric phase stability and polarization magnitude. This work provides electrode material selection guidelines toward the development of high-performing ferroelectric hafnia into microelectronic devices, such as nonvolatile memories.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Full-Field Strain Measurement Integrated with Two Dimension Regression Analysis to Evaluate the Bi-Modulus Elastic Properties of Isotropic and Transversely Isotropic Materials

Background: Measuring the physical properties of shale is critical for optimizing engineering activities such as geothermal energy generation and hydraulic fracturing. Shale is a transversely isotropic material. Furthermore, this material can also include micro and macro cracks at different locations and orientations that cause it to behave differently under tensile or compressive loading. Objective: In this work, a combined experimental–numerical approach is proposed to evaluate the bi-modulus elastic properties of isotropic and transversely isotropic materials. Methods: Full-field strain measurements for a circular disk under diametral compression are integrated with a regression analysis technique to evaluate the elastic properties of bi-modulus materials subjected to tensile and compressive loads using two loading configurations on the same specimen. Digital Image Correlation (DIC) is used to measure the full-field strains. Subsequently, in the case of an isotropic material, a linear least-squares approach is utilized to process the experimentally determined strains in conjunction with analytical expressions of the stress fields (in terms of far-field loading) to determine the elastic modulus E, the shear modulus G, and the Poisson’s ratio $v$. In the case of a transversely isotopic material, such as shale, a finite element model is implemented to determine the stress fields (again in terms of far-field loading), which is followed by repeating the previous regression analysis in an iterative process to estimate the elastic parameters. Results: The results show that the proposed technique successfully provides a complete set of elastic properties as a function of both the loading condition and the principal material directions. The technique is validated by measurements on a known isotropic material and then applied to determine the properties of shale. Conclusion: In this work, the proposed approach is successfully used to calculate the bi-modulus elastic response of poly(methyl meth- acrylate) (PMMA) and shale. As expected, PMMA exhibits an isotropic response with no bi-modulus effect, however, shale exhibits both transverse isotropy and a bi-modulus effect. Therefore, this approach holds promise for investigating the elastic properties of materials like rocks and fiber-reinforced composite laminates as functions of the principal material directions and the loading conditions.

42 ENGINEERING↗
DOE OSTI2016

AGC-1 Irradiation Induced Property Changes Analysis Report: Dynamic Elastic Modulus

Recent analyses of some of the test property data from the AGC-1 creep capsule are reported. Specifically the analyses of data for the effects of compressive creep strain on the Dynamic elastic modulus (by the fundamental frequency and ultrasonic velocity/tof methods) are reported. Statistical “t” testing was used to establish the statistical significance of any differences observed between the Dynamic elastic modulus of the creep (irradiated with compressive stress) and the control (irradiated without stress) specimens. Compressive creep strain does have a small effect on Dynamic elastic modulus, reducing it at the higher doses as volume turnaround is approached.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2016

Hardness, elastic modulus, and wear resistance of hafnium oxide-based films grown by atomic layer deposition

The investigation of mechanical properties of atomic layer deposition HfO{sub 2} films is important for implementing these layers in microdevices. The mechanical properties of films change as a function of composition and structure, which accordingly vary with deposition temperature and post-annealing. This work describes elastic modulus, hardness, and wear resistance of as-grown and annealed HfO{sub 2}. From nanoindentation measurements, the elastic modulus and hardness remained relatively stable in the range of 163–165 GPa and 8.3–9.7 GPa as a function of deposition temperature. The annealing of HfO{sub 2} caused significant increase in hardness up to 14.4 GPa due to film crystallization and densification. The structural change also caused increase in the elastic modulus up to 197 GPa. Wear resistance did not change as a function of deposition temperature, but improved upon annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Elastic Modulus Measurement at High Temperatures for Miniature Ceramic Samples Using Laser Micro-Machining and Thermal Mechanical Analyzer

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale at high temperatures. We used a picosecond laser to precisely cut microbeams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm and a length of ~1 cm. They were then tested in a thermal mechanical analyzer at room temperature, 500 °C, 800 °C, and 1100 °C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

Chemistry↗
DOE OSTI2016

Simultaneous determination of the residual stress, elastic modulus, density and thickness of ultrathin film utilizing vibrating doubly clamped micro-/nanobeams

Measurement of ultrathin film thickness and its basic properties can be highly challenging and time consuming due to necessity of using several very sophisticated devices. Here, we report an easy accessible resonant based method capable to simultaneously determinate the residual stress, elastic modulus, density and thickness of ultrathin film coated on doubly clamped micro-/nanobeam. We show that a general dependency of the resonant frequencies on the axial load is also valid for in-plane vibrations, and the one depends only on the considered vibrational mode. As a result, we found that the film elastic modulus, density and thickness can be evaluated from two measured in-plane and out-plane fundamental resonant frequencies of micro-/nanobeam with and without film under different prestress forces. Whereas, the residual stress can be determined from two out-plane (in-plane) measured consecutive resonant frequencies of beam with film under different prestress forces without necessity of knowing film and substrate properties and dimensions. Moreover, we also reveal that the common uncertainties in force (and thickness) determination have a negligible (and minor) impact on the determined film properties. The application potential of the present method is illustrated on the beam made of silicon and SiO{sub 2} with deposited 20 nm thick AlN and 40 nm thick Au thin films, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Ion irradiation induced structural modifications and increase in elastic modulus of silica based thin films

Ion irradiation is an alternative to heat treatment for transforming organic-inorganic thin films to a ceramic state. One major shortcoming in previous studies of ion-irradiated films is the assumption that constituent phases in ion-irradiated and heat-treated films are identical and that the ion irradiation effect is limited to changes in composition. Here, we investigate the effects of ion irradiation on both the composition and structure of constituent phases and use the results to explain the measured elastic modulus of the films. Our results indicated that the microstructure of the irradiated films consisted of carbon clusters within a silica matrix. It was found that carbon was present in a non-graphitic sp 2 -bonded configuration. It was also observed that ion irradiation caused a decrease in the Si-O-Si bond angle of silica, similar to the effects of applied pressure. A phase transformation from tetrahedrally bonded to octahedrally bonded silica was also observed. The results indicated the incorporation of carbon within the silica network. Finally, a combination of the decrease in Si-O-Si bond angle and an increase in the carbon incorporation within the silica network was found to be responsible for the increase in the elastic modulus of the films.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Anomalously high elastic modulus of a poly(ethylene oxide)-based composite electrolyte

The practical use of lithium metal anodes in solid-state batteries requires a polymer membrane with high lithium-ion conductivity, thermal/electrochemical stability, and mechanical strength. The primary challenge is to effectively decouple the ionic conductivity and mechanical strength of the polymer electrolytes. We report a remarkably facile single step synthetic strategy based on in-situ crosslinking of poly(ethylene oxide) (xPEO) in the presence of a woven glass fiber (GF). Such a simple method yields composite polymer electrolytes (CPE) of anomalously high elastic modulus up to 2.5 GPa over a broad temperature range (20 °C – 245 °C) that has never been previously documented. An unsupervised machine learning algorithm, K-mean clustering analysis, was implemented on the hyperspectral Raman mapping at the xPEO/GF interface. Using such a unique means, we show for the first time that the promoted mechanical strength originates from xPEO and GF interactions through dynamic hydrogen and ionic bonding. High ionic conductivity is achieved by the addition plasticizer (e.g. tetraglyme), where trifluoromethanesulfonate anions are tethered to the xPEO matrix and Li + cations are favorably transported through coordination with the plasticizer. Further, stringent galvanostatic cycling tests indicates the CPE can be stably cycled for >3000 h in a Li-metal symmetric cell at a moderate temperature (nearly 1500 Coulombs/cm 2 Li equivalents), outperforming most of the PEO-based electrolytes. The GF reinforced CPE reported here has multifunctional uses, such as solid electrolytes for all solid-state batteries and membranes for redox-flow batteries. Although the focus of this study is on lithium-based batteries, the results are equally promising for other alkali metal based batteries such as sodium and potassium.

25 ENERGY STORAGE↗
DOE OSTI2019

Elastic Modulus Estimation for Copper Syntactic Foams Reinforced with Iron Hollow Spheres of Different Wall Thicknesses

The present study estimates the effect on Young’s modulus of the percentage and thickness of iron hollow spheres reinforcing copper syntactic foams. The resulting materials were modeled by inserting hollow spheres in a random arrangement, using a combination of Discrete Element Method (DEM) for generating the sphere location coordinates and Finite Element Analysis (FEA). Estimations for syntactic foams were compared to those obtained for conventional copper foams with the same porosity. Results showed that the elastic modulus of both syntactic and conventional foams drops significantly as the percentage of spheres or porosity increases. Furthermore, the increase in the wall thickness of the iron hollow spheres leads to significant rises in the Young’s modulus. Depending on the desired mechanical properties, the outcomes presented in this work could be used for selecting the kind of foam (syntactic or conventional) and predesign some characteristics such as porosity or thickness of the spheres or pores.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Compositional and phase dependence of elastic modulus of crystalline and amorphous Hf 1- x Zr x O 2 thin films

The elastic moduli of amorphous and crystalline atomic layer-deposited Hf 1-x Zr x O 2 (HZO, x = 0, 0.31, 0.46, 0.79, 1) films prepared with TaN electrodes on silicon substrates were investigated using picosecond acoustic measurements. The moduli of the amorphous films were observed to increase between 211 ± 6 GPa for pure HfO 2 and 302 ± 9 GPa for pure ZrO 2 . In the crystalline films, it was found that the moduli increased upon increasing the zirconium composition from 248 ± 6 GPa for monoclinic HfO 2 to 267 ± 9 GPa for tetragonal ZrO 2 . Positive deviations from this increase were observed for the Hf 0.69 Zr 0.31 O 2 and Hf 0.54 Zr 0.46 O 2 compositions, which were measured to have moduli of 264 ± 8 GPa and 274 ± 8 GPa, respectively. These two compositions contained the largest fractions of the ferroelectric orthorhombic phase, as assessed from polarization and diffraction data. The biaxial stress states of the crystalline films were characterized through sin 2 (ψ) x-ray diffraction analysis. The in-plane stresses were all found to be tensile and observed to increase with the increasing zirconium composition, between 2.54 ± 0.6 GPa for pure HfO 2 and 5.22 ± 0.5 GPa for pure ZrO 2 . The stresses are consistent with large thermal expansion mismatches between the HZO films and silicon substrates. Furthermore, these results demonstrate a device-scale means to quantify biaxial stress for investigation on its effect on the ferroelectric properties of hafnia-based materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental Assessment of Elastic Modulus vs. Relative Density for Stretch- and Bend-Dominated Lattices

This project was designed to study the possibility of using structural properties of lattices to replicate the material properties of certain hard to manufacture designs and use topology optimization to determine the lattice type and density required to mimic these properties. The integration of additively manufactured lattice structures with topology optimization highlights the need for well characterized mechanical properties and uncertainty analyses to insure these optimized structures respond as predicted. Stereolithographically printed octet and rhombic dodecahedron lattices were manufactured at 10%, 25% and 65% density by volume. As a separate task, yet integrated into this work, finite element analysis (FEA) was used to predict the printed lattice’s mechanical properties, which were then compared to our experimental results. After comparing FEA and experimentallymeasured elastic moduli, it was determined that the FEA provides highly reliable predictions for the modulus of these printed lattice structures. These lattices also exhibited greater tensile stiffness than that of the solid material demonstrating the flexibility that lattices provide to designing parts with designer structural properties. The accurate printing and reliable modeling of these lattices will enable topology optimization of complex parts from well-characterized rhombic dodecahedron and octet lattice structures of varying densities.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Using porous random fields to predict the elastic modulus of unoxidized and oxidized superfine graphite

Nuclear graphite is a candidate material for Generation IV nuclear power plants. Porous materials such as graphite can contain complex networks of pores that influence the material's mechanical and irradiation response. A methodology known as the random finite element method (RFEM) was adapted to create synthetic microstructures and predict the influence of porosity on the elastic properties of graphite during oxidation. RFEM combines random field theory and the finite element method in a Monte Carlo framework to estimate the mechanical response of a given grade of graphite. In this research, the random fields were verified through experimental characterization to predict the elastic response of three nuclear graphite grades, ETU-10, IG-110, and 2114. Finite element models (FEM) were generated using segmentations of x-ray computed tomography (XCT) data known as image-based models (IBMs) to validate and compare with the RFEM results and better understand the effects of uniform oxidation in these graphite grades. The RFEM predictions appear to correlate well with the experimental values of the measured Young’s modulus of the three graphite grades and display the same trends as IBMs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Probing the elastic modulus and hardness of superionic boron cluster solid electrolytes

Polyhedral borane salts are highly tunable compounds with the potential to be used as solid electrolytes due to their high Li and Na superionic conductivity and relatively wide electrochemical stability window. In considering their application to all solid-state batteries, their mechanical properties play a critical role in their operation due to stresses the solid electrolyte is subjected to during battery operation. Density functional theory (DFT) calculations have provided an initial assessment of bulk and elastic moduli for some selected boron cluster solid electrolytes, but direct measurements are still scarce. Here, in this paper, we report the elastic moduli and hardnesses of LiCB 11 H 12 , LiCB 9 H 10 , NaCB 11 H 12 , and NaCB 9 H 10 for the first time using nanoindentation continuous stiffness method (CSM) measurements under inert atmosphere. Experimental modulus values ranging 8.8–12.3 GPa and hardness values ranging 0.15–0.38 GPa are lower than that of other inorganic solid-state electrolytes such as oxide- and sulfide-based solid electrolytes. DFT calculations on the expected moduli of these compounds are also presented and discussed. Analysis of the indentation plasticity index reveals that these compounds have higher plasticity index compared to other common oxide and sulfide solid electrolytes. According to the calculated Pugh's ratio, all compounds in this study except LiCB 11 H 12 are considered ductile.

25 ENERGY STORAGE↗