Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINE STARTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Turbojet-engine Starting and Acceleration

From considerations of safety and reliability in performance of gas-turbine aircraft, it is clear that engine starting and acceleration are of utmost importance. For this reason extensive efforts have been devoted to the investigation of the factors involved in the starting and acceleration of engines. In chapter III it is shown that certain basic combustion requirements must be met before ignition can occur; consequently, the design and operation of an engine must be tailored to provide these basic requirements in the combustion zone of the engine, particularly in the vicinity of the ignition source. It is pointed out in chapter III that ignition by electrical discharges is aided by high pressure, high temperature, low gas velocity and turbulence, gaseous fuel-air mixture, proper mixture strength, and-an optimum spark. duration. The simultaneous achievement of all these requirements in an actual turbojet-engine combustor is obviously impossible, yet any attempt to satisfy as many requirements as possible will result in lower ignition energies, lower-weight ignition systems, and greater reliability. These factors together with size and cost considerations determine the acceptability of the final ignition system. It is further shown in chapter III that the problem of wall quenching affects engine starting. For example, the dimensions of the volume to be burned must be larger than the quenching distance at the lowest pressure and the most adverse fuel-air ratio encountered. This fact affects the design of cross-fire tubes between adjacent combustion chambers in a tubular-combustor turbojet engine. Only two chambers in these engines contain spark plugs; therefore, the flame must propagate through small connecting tubes between the chambers. The quenching studies indicate that if the cross-fire tubes are too narrow the flame will not propagate from one chamber to another. In order to better understand the role of the basic factors in actual engine operation, many investigations have been conducted in single combustors from gas-turbine engines and in full-scale engines in altitude tanks and in flight. The purpose of the present chapter is to discuss the results of such studies and, where possible, to interpret these results qualitatively in terms of the basic requirements reported in chapter III. The discussion parallels the three phases of turbojet engine starting: (1) Ignition of the fuel-air mixture (2) Propagation of flame throughout the combustion zone (3) Acceleration of the engine to operating speed.

Mc Cafferty, R. J.↗
NASA NTRS1997

Space Shuttle Main Engine Start with Off-Nominal Propellant Inlet Pressures

This paper describes Rocketdyne's successful analysis and demonstration of the Space Shuttle Main Engine (SSME) operation at off-nominal propellant inlet conditions during the Reusable Launch Vehicle (RLV) evaluation tests. The nominal inlet condition range is: 103 to 111 psia and 170.5 to 178 deg. R for the oxidizer and 43 to 47 psia and 37 to 40 deg. R for the fuel. The SSME start was successfully demonstrated with engine inlet pressures of 50 psia liquid oxygen (LOX) with subcooled LOX at 160 deg R and 38 psia fuel at 38 deg. R. Four tests were used to incrementally modify the start sequence to demonstrate the final goal.

Bradley, Michael↗
NASA NTRS1992

Operationally Efficient Propulsion System Study (OEPSS) Data Book: Integrated Booster Propulsion Module (BPM) Engine Start Dynamics - Volume 8

A fluid-dynamic, digital-transient computer model of an integrated, parallel propulsion system was developed for the CDC mainframe and the SUN workstation computers. Since all STME component designs were used for the integrated system, computer subroutines were written characterizing the performance and geometry of all the components used in the system, including the manifolds. Three transient analysis reports were completed. The first report evaluated the feasibility of integrated engine systems in regards to the start and cutoff transient behavior. The second report evaluated turbopump out and combined thrust chamber/turbopump out conditions. The third report presented sensitivity study results in staggered gas generator spin start and in pump performance characteristics.

Kemp, Victoria R.↗
NASA NTRS1991

STS-37: TCDT Pad B Atlantis GRO (3 of 3)

Live footage shows some beautiful panoramic views of STS-37 on the pad. Scenes include the narration of simulated auto sequence start, engine start, engine firing and cut-off. Also shown is the crew emergency egress procedure. This is tape 3 of 3. Tape 1 has a report # of NONP-NASA-VT-2000013416, and tape 2 has a report # of NONP-NASA-VT-2000013417.

Source record↗
NASA NTRS1993

Approach to SSME health monitoring. III - Exhaust plume emission spectroscopy: Recent results and detailed analysis

Spectral data for two recent A-1 test firings, 901-717 and 901-718, obtained from an Optical Multichannel Analyzer and an Optical Plume Anomaly Detector, are presented. The spectral data encompasses the database of SSME critical components and materials and the spectral database for the SSME related elements and materials. Relatively strong and continuous emissions from Cr and Fe atomic transitions were observed starting at engine start plus 494 s and persisting until the engine shut off at engine start plus 520 s. These emissions are considered to be emanated from the SSME material AISI 440C, which is traced to high pressure turbopump bearings.

Tejwani, Gopal D.↗
NASA NTRS1975

Centaur zero gravity coast and engine restart demonstration on the Titan/Centaur (TC-2) extended mission

The Centaur propellant management and thermal control techniques required for zero gravity coasting were successfully demonstrated during an extended mission following spacecraft separation on the TC-2 flight. As part of the demonstration, two successful engine starts were accomplished. The first engine start followed a one-hour zero gravity coast, and the second engine start followed a three-hour zero gravity coast. All of the Centaur systems performed satisfactorily, the design parameters for zero gravity coasting were verified, and no significant problems were encountered. The flight results showed that the propellant location and behavior, propellant heating, and tank pressure rise rates observed during the zero-gravity coasts were less severe than expected. Consequently, the majority of the propellants remained at the tank bottom, the propellant collection times were very short, and more than 7 hours of coast could have been achieved before a tank venting was required. The tank pressurization prior to the engine starts provided boost pump Net Positive Suction Head values well in excess of the values required. The LO2 tank pressurization was accomplished by a new bubbler method that greatly reduced the helium usage.

Lacovic, R. F.↗
NASA NTRS1997

Evaluation of an Ejector Ramjet Based Propulsion System for Air-Breathing Hypersonic Flight

A Rocket Based Combined Cycle (RBCC) engine system is designed to combine the high thrust to weight ratio of a rocket along with the high specific impulse of a ramjet in a single, integrated propulsion system. This integrated, combined cycle propulsion system is designed to provide higher vehicle performance than that achievable with a separate rocket and ramjet. The RBCC engine system studied in the current program is the Aerojet strutjet engine concept, which is being developed jointly by a government-industry team as part of the Air Force HyTech program pre-PRDA activity. The strutjet is an ejector-ramjet engine in which small rocket chambers are embedded into the trailing edges of the inlet compression struts. The engine operates as an ejector-ramjet from take-off to slightly above Mach 3. Above Mach 3 the engine operates as a ramjet and transitions to a scramjet at high Mach numbers. For space launch applications the rockets would be re-ignited at a Mach number or altitude beyond which air-breathing propulsion alone becomes impractical. The focus of the present study is to develop and demonstrate a strutjet flowpath using hydrocarbon fuel at up to Mach 7 conditions. Freejet tests of a candidate flowpath for this RBCC engine were conducted at the NASA Lewis Research Center's Hypersonic Tunnel Facility between July and September 1996. This paper describes the engine flowpath and installation, outlines the primary objectives of the program, and describes the overall results of this activity. Through this program 15 full duration tests, including 13 fueled tests were made. The first major achievement was the further demonstration of the HTF capability. The facility operated at conditions up to 1950 K and 7.34 MPa, simulating approximately Mach 6.6 flight. The initial tests were unfueled and focused on verifying both facility and engine starting. During these runs additional aerodynamic appliances were incorporated onto the facility diffuser to enhance starting. Both facility and engine starting were achieved. Further, the static pressure distributions compared well with the results previously obtained in a 40% subscale flowpath study conducted in the LERC 1X1 supersonic wind tunnel (SWT), as well as the results of CFD analysis. Fueled performance results were obtained for the engine at both simulated Mach 6 (1670 K) and Mach 6.6 (1950 K) conditions. For all these tests the primary fuel was liquid JP-10 with gaseous silane (a mixture of 20% SiH4 and 80% H2 by volume) as an ignitor/pilot. These tests verified performance of this engine flowpath in a freejet mode. High combustor pressures were reached and significant changes in axial force were achieved due to combustion. Future test plans include redistributing the fuel to improve mixing, and consequently performance, at higher equivalence ratios.

Thomas, Scott R.↗
NASA NTRS2000

X33 Transient Liftoff Analysis

The successful design of a launch vehicle requires the careful characterization of the various loads the structure will experience over its lifetime. Many of the most demanding load environments occur during the launch/ascent phase of a mission, typically defined as the point of engine start through engine cut off. One of the critical events during the launch phase is the liftoff event. This event imparts high loads on the vehicle due to transient events such as thrust build-up and vehicle release. This paper describes the theory and procedures used to calculate structural loads due to the liftoff event for the Lockheed-Martin X33 technology demonstrator vehicle. These procedures were developed at NASA's Marshall Space Flight Center and verified previously on other advanced launch system concepts and the Space Shuttle system.

Peck, Jeff↗
NASA NTRS1966

Thermal Control of Liquid H2/O2 Rocket Engines and Vehicle Impact

Cryogenic propulsion systems are subjected to various engine start environments during ground testing, first burn, and restart after orbital coast. These operational modes necessitate careful engine-stage integration, particularly in thermal control of propellant feed systems and engine subsystems. The wide range of operational conditions imposed on propellant feed systems include varying heat loads and acceleration forces for static test first burn and orbital restart. One method used to provide Net Positive Suctign,Head (NPSH) and maintain turbopump I is thermal control propellant circulation through the feed system prior to engine start. The attendant design and operational criteria are inter-related with stage and vehicle systems, including for example, auxiliary propulsion and propellant ullaging methods such as propellant tank propulsive venting. Thermally sensitive engine components require environmental control, protection, or special sequencing in order to assure repeatable engine start performance. An example is thrust chamber pre-chill to avoid pump stall during rapid start transient. Trends in engine development are toward expanding system flexibility to accommodate the wide variety of environments without special pre-start conditioning.

Winstead, Thomas W.↗
NASA NTRS2001

Use of Soft Computing Technologies for a Qualitative and Reliable Engine Control System for Propulsion Systems

The problem to be addressed in this paper is to explore how the use of Soft Computing Technologies (SCT) could be employed to improve overall vehicle system safety, reliability, and rocket engine performance by development of a qualitative and reliable engine control system (QRECS). Specifically, this will be addressed by enhancing rocket engine control using SCT, innovative data mining tools, and sound software engineering practices used in Marshall's Flight Software Group (FSG). The principle goals for addressing the issue of quality are to improve software management, software development time, software maintenance, processor execution, fault tolerance and mitigation, and nonlinear control in power level transitions. The intent is not to discuss any shortcomings of existing engine control methodologies, but to provide alternative design choices for control, implementation, performance, and sustaining engineering, all relative to addressing the issue of reliability. The approaches outlined in this paper will require knowledge in the fields of rocket engine propulsion (system level), software engineering for embedded flight software systems, and soft computing technologies (i.e., neural networks, fuzzy logic, data mining, and Bayesian belief networks); some of which are briefed in this paper. For this effort, the targeted demonstration rocket engine testbed is the MC-1 engine (formerly FASTRAC) which is simulated with hardware and software in the Marshall Avionics & Software Testbed (MAST) laboratory that currently resides at NASA's Marshall Space Flight Center, building 4476, and is managed by the Avionics Department. A brief plan of action for design, development, implementation, and testing a Phase One effort for QRECS is given, along with expected results. Phase One will focus on development of a Smart Start Engine Module and a Mainstage Engine Module for proper engine start and mainstage engine operations. The overall intent is to demonstrate that by employing soft computing technologies, the quality and reliability of the overall scheme to engine controller development is further improved and vehicle safety is further insured. The final product that this paper proposes is an approach to development of an alternative low cost engine controller that would be capable of performing in unique vision spacecraft vehicles requiring low cost advanced avionics architectures for autonomous operations from engine pre-start to engine shutdown.

Trevino, Luis↗
NASA NTRS2005

Key Reliability Drivers of Liquid Propulsion Engines and A Reliability Model for Sensitivity Analysis

This paper is to address the in-flight reliability of a liquid propulsion engine system for a launch vehicle. We first establish a comprehensive list of system and sub-system reliability drivers for any liquid propulsion engine system. We then build a reliability model to parametrically analyze the impact of some reliability parameters. We present sensitivity analysis results for a selected subset of the key reliability drivers using the model. Reliability drivers identified include: number of engines for the liquid propulsion stage, single engine total reliability, engine operation duration, engine thrust size, reusability, engine de-rating or up-rating, engine-out design (including engine-out switching reliability, catastrophic fraction, preventable failure fraction, unnecessary shutdown fraction), propellant specific hazards, engine start and cutoff transient hazards, engine combustion cycles, vehicle and engine interface and interaction hazards, engine health management system, engine modification, engine ground start hold down with launch commit criteria, engine altitude start (1 in. start), Multiple altitude restart (less than 1 restart), component, subsystem and system design, manufacturing/ground operation support/pre and post flight check outs and inspection, extensiveness of the development program. We present some sensitivity analysis results for the following subset of the drivers: number of engines for the propulsion stage, single engine total reliability, engine operation duration, engine de-rating or up-rating requirements, engine-out design, catastrophic fraction, preventable failure fraction, unnecessary shutdown fraction, and engine health management system implementation (basic redlines and more advanced health management systems).

Huang, Zhao-Feng↗
NASA NTRS1996

STS-78 Flight Day 1

On this first day of the STS-78 mission, the flight crew, Cmdr. Terence T. Henricks, Pilot Kevin R. Kregel, Payload Cmdr. Susan J. Helms, Mission Specialists Richard M. Linnehan, Charles E. Brady, Jr., and Payload Specialists Jean-Jacques Favier, Ph.D. and Robert B. Thirsk, M.D., can be seen preforming pre-launch activities such as eating the traditional breakfast, crew suit-up, and the ride out to the launch pad. Also included are various panoramic views of the shuttle on the pad. The crew can be seen being readied in the white room for their mission. After the closing of the hatch and arm retraction, launch activities are shown including countdown, engine ignition, launch, and the separation of the Solid Rocket Boosters. Henricks shares a unique view of Columbia's climb to orbit with flight controllers from a small camera that was mounted on the flight deck. The video follows Columbia's flight from just before main engine start through main engine cutoff, showing the force of main engine and solid booster ignition as experienced by the astronauts.

Source record↗
NASA NTRS1974

Propulsion system tests on a full scale Centaur vehicle to investigate 3-burn mission capability of the D-lT configuration

Propulsion system tests were conducted on a full scale Centaur vehicle to investigate system capability of the proposed D-lT configuration for a three-burn mission. This particular mission profile requires that the engines be capable of restarting and firing for a final maneuver after a 5-1/2-hour coast to synchronous orbit. The thermal conditioning requirements of the engine and propellant feed system components for engine start under these conditions were investigated. Performance data were also obtained on the D-lT type computer controlled propellant tank pressurization system. The test results demonstrated that the RL-10 engines on the Centaur vehicle could be started and run reliably after being thermally conditioned to predicted engine start conditions for a one, two and three burn mission. Investigation of the thermal margins also indicated that engine starts could be accomplished at the maximum predicted component temperature conditions with prestart durations less than planned for flight.

Groesbeck, W. A.↗
NASA NTRS1984

Diesel engine catalytic combustor system

A low compression turbocharged diesel engine is provided in which the turbocharger can be operated independently of the engine to power auxiliary equipment. Fuel and air are burned in a catalytic combustor to drive the turbine wheel of turbine section which is initially caused to rotate by starter motor. By opening a flapper value, compressed air from the blower section is directed to catalytic combustor when it is heated and expanded, serving to drive the turbine wheel and also to heat the catalytic element. To start, engine valve is closed, combustion is terminated in catalytic combustor, and the valve is then opened to utilize air from the blower for the air driven motor. When the engine starts, the constituents in its exhaust gas react in the catalytic element and the heat generated provides additional energy for the turbine section.

Ream, L. W.↗
NASA NTRS1978

The stirling engine for vehicle propulsion

The performance data of experimental Stirling engines are considered along with questions of exhaust-gas composition, engine noise, engine volume and weight, engine control, and the engine-starting process. The Stirling engine can use practically any liquid or gaseous fuel for its operation. It is found that technically a use of the Stirling engine in motor vehicles is feasible. Economic questions related to an introduction of the Stirling engine are discussed along with possible new developments which could improve the economic situation in favor of a use of Stirling engine.

Kuhlman, P.↗