Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENGINES - INTERCOOLERS - PRESSURE DROP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Harnessing the Hydroelectric Potential of Engineered Drops (Final Technical Report)

The potential for low-head hydropower in the engineered drops in both federal and private irrigation system is well known and significant. The environmental and socio/recreational impacts of harnessing this renewable energy resource in man-made conduits are much less, and often insignificant, compared with comparable hydro-electric potential in natural water features on rivers, lakes, and streams. Yet, few new plants have been commissioned in more than two decades. Over the same time period, low head hydro installations in Germany have more than doubled. The challenge is in finding economical ways to harness the hydro-electric potential in the engineered drops, and efficiently deliver the power to the grid. The objectives of Percheron Power, LLC's (Percheron Power) Project were to design, develop, permit, and operate an innovative low-head hydro-electric generation facility on an existing engineered drop of a large irrigation canal system. The hydro-electric generation facility was designed to employ a new type of turbine and technology, called an Archimedes Hydrodynamic Screw (AHS), to harness the existing potential of the engineered drop. The goal was to demonstrate the new lower cost AHS technology system to federal agencies, irrigation districts and other system owners and to support further development of new small hydropower projects at previously marginal low-head sites in the U.S. The objective of this funding opportunity of the Department of Energy Water Power Technologies Office was to reduce the Levelized Cost of Energy (LCOE) for small hydropower to less than ${$}$0.07/kWh (${$}$70/MWh) to be competitive with existing base-load power sources such as coal-powered power plants.

13 HYDRO ENERGY↗
DOE OSTI2022

Fuel Effects on Multimode Engine Operation (Sandia National Laboratories) (DOE VTO Annual Progress Report for FY21)

In total, light-duty vehicles in the United States travel on the order of 3 trillion miles annually, providing tremendous societal and personal benefits. However, the environmental burden is excessive, prompting Co-Optimization of Fuel and Engines (Co-Optima) program efforts to provide the science needed to increase engine efficiency and produce non-fossil fuels with reduced greenhouse gas emissions. Boosted spark-ignition (SI) engines provide high power density by offering high loads and engine speeds, making them light-weight and attractive for light-duty vehicles. Unfortunately, the engine efficiency drops off at lower loads and speeds, where the engine spends most time during typical driving. Multimode SI engines can use a more efficient advanced lean combustion mode at lower loads and speeds, while reverting to boosted SI under high-load conditions. Within Co-Optima, multiple advanced lean combustion modes have been explored; these include stratified-charge SI, pre-chamber lean SI, and advanced compression ignition (ACI) techniques such as spark-assisted compression ignition (SACI). For these combustion modes, focus has been on determining fuel properties that enable higher engine efficiency, clean and stable combustion, and effective exhaust aftertreatment. This report highlights recent efforts funded by the Vehicle Technologies Office at multiple National Laboratories that supported the multimode project in Co-Optima. It also includes a brief summary of biofuel production research funded by the Bioenergy Technologies Office.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

SAVY-4000 Finite-Element Drop Test Analysis

PFE Auxiliary Systems conducted drop testing on SAVY-4000 containers to evaluate structural response under 12-foot drop conditions. In support of that effort, a finite-element modeling capability was developed to simulate drop response across multiple container sizes and impact orientations. The purpose of this work was to provide a consistent analysis framework that could support interpretation of testing, compare response trends across multiple configurations, and generate quantities of interest for later comparison with experimental data. More broadly, the analysis and testing were intended to assess whether the containers continued to perform their primary function after a 12-foot drop, namely maintaining structural integrity and containment of the contents. The modeling approach combined an implicit preload analysis with an explicit drop simulation so that each drop event began from a mechanically realistic assembled condition, including compression of the silicone O-ring. Separate models were developed for 2-quart, 5-quart, 12-quart, and 10-gallon containers. The results were evaluated in terms of strain-gauge response, collar-lid gap behavior, and accumulated plastic strain. In addition, parametric studies were performed on the 2-quart container to assess sensitivity to O-ring stiffness, friction, canister thickness, geometry tolerance, and mesh density. The simulations showed that predicted drop responses depended strongly on both container size and drop orientation. Gap metrics identified cases in which the predicted collar-lid opening exceeded the nominal O-ring cross-section threshold, while plastic strain metrics identified localized regions of elevated permanent deformation. Parametric studies showed that the predicted response was especially sensitive to the assumed O-ring stiffness and contact friction, while the geometry tolerance study produced smaller changes in the cases examined. The main value of this work was that it established a repeatable modeling and simulation workflow to support drop-test implementation, evaluate effects of future configuration changes, and understand modeling assumptions that most influenced predicted response. At the current stage, the results were viewed as preliminary model predictions rather than validated predictions. The next step would be to compare drop-test data to the model so that predictive values of the workflow could be refined and used with greater confidence to assess whether the containers maintained structural integrity and containment of the contents after a 12-foot drop.

42 ENGINEERING↗
DOE OSTI2020

Closed-form theoretical model of the secondary drop size in partial coalescence—Capturing pertinent timescales and viscous forces

One of the most important outcomes of partial drop coalescence is the ratio of the secondary drop radius to the primary drop radius, known as the drop ratio, ri. This ratio is thought to be approximately constant and independent of physical parameters of the fluids involved. However, here we reveal that ambient fluid viscosity can alter the size of the secondary drop and the drop ratio consequently. Using scaling analysis, we derive a model that predicts the behavior of the drop ratio as a function of the Ohnesorge number, a dimensionless ratio of viscous to inertial forces. In addition, we present our experimental results of coalescing drops on a planar interface under the influence of surface tension gradients. A high-speed digital camera is used to observe the evolution of drops as they coalesce with a bulk liquid. We show that this process is influenced by the surface tension gradient between the drop and the bulk liquid. The ratio of the secondary drop to the primary drop in partial coalescence is smaller than the reported values for coalescence without a surface tension gradient. The analytical model derived through this study is based on a new modified Ohnesorge number that includes surface tension gradients. Our analytical model is compared against other models and the results illustrate good agreement with our experimental findings and experimental data in the literature.

42 ENGINEERING↗
DOE OSTI2021

High-speed impact of micron-sized diesel drop trains—Splashing dynamics, secondary droplet formation, and effects of pre-existing film thickness

This work investigates surface impingement of monodispersed diesel drop trains using computational simulations. The three-dimensional simulations include high-speed impact of micrometer-sized fuel drops onto initially dry and wetted stainless steel substrates. The drop size and impact velocity are representative of fuel injection conditions in internal combustion engines (ICEs). The drop trains serve as a simplified representation of fuel spray. To accurately capture the film that naturally develops on initially dry substrates, a dynamic diesel-stainless steel contact angle model was developed using experiments of single drop impact under ICE representative temperature. Simulations are presented for a highly splashing case and the effects of a pre-existing film on splashing dynamics were investigated, including the temporal evolution of splashed mass and film thickness. It was concluded that for thin films, the effect of pre-existing film thickness is less significant than in single drop impingement. Secondary droplet characterization was performed on simulation results, leading to instantaneous and time-averaged distributions of secondary droplet size, velocity magnitude, and trajectory angle. It was found that for each drop impingement, approximately 58% of the splashed mass is from the impinging drop itself, while the remainder of the splashed mass is composed of film liquid. From a high resolution case, details of secondary droplet formation are observed and three distinct phases of secondary droplet formation are identified. The detailed analysis of drop train impingement under engine-relevant conditions serves as a first step toward a robust understanding of fuel impingement and the development of cleaner and more efficient ICEs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Triacylglycerol, total fatty acid, and biomass accumulation of metabolically engineered energycane grown under field conditions confirms its potential as feedstock for drop‐in fuel production

Abstract Metabolic engineering for hyperaccumulation of lipids in vegetative tissues of high biomass crops promises a step change in oil yields for the production of advanced biofuels. Energycane is the ideal feedstock for this approach due to its exceptional biomass production and persistence under marginal conditions. Here, we evaluated metabolically engineered energycane with constitutive expression of the lipogenic factors WRINKLED 1 ( WRI 1), DIACYLGLYCEROL ACYLTRANSFERASE 1 ( DGAT 1), and OLEOSIN 1 ( OLE 1) for the accumulation of triacylglycerol (TAG), total fatty acid (TFA), and biomass under field conditions at the University of Florida‐IFAS experiment station near Citra, Florida. TAG and TFA accumulation were highest in leaves (up to 9.9% and 12.9% of DW, respectively), followed by juice from crushed stems, stems, and roots. TAG and TFA accumulation increased up to harvest time and correlated highest with OLE 1 and DGAT 1 expression. Biomass dry weight, TAG, and TFA content differed greatly depending on DGAT 1 and OLE 1 expression in transgenic lines with similar WRI 1 expression. Biomass did not significantly differ between WT and line L2 with DAGT 1 and OLE 1 expressed at low levels and TAG and TFA accumulating to 12‐ and 1.6‐fold that of WT leaves, respectively. In contrast, line L13, with intron‐mediated enhancement of DGAT 1 expression, displayed a 245‐ to 330‐fold increase in TAG and a 4.75‐ to 6.45‐fold increase in TFA content compared with WT leaves and a biomass reduction of 52%. These results provide the basis for developing novel feedstocks for expanding plant lipid production and point to new prospects for advanced biofuels.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Respiration is essential for aerobic growth of Zymomonas mobilis ZM4

ABSTRACT Zymomonas mobilis is an alpha-proteobacterium that is a promising platform for industrial scale production of biofuels due to its efficient ethanol fermentation and low biomass generation. Z. mobilis is aerotolerant and encodes a complete respiratory electron transport chain, but the benefit of respiration for growth in oxic conditions has never been confirmed, despite decades of research. Growth and ethanol production of wild-type Z. mobilis is poor in oxic conditions indicating that it does not benefit from oxidative phosphorylation. Additionally, in previous studies, aerobic growth improved significantly when respiratory genes were disrupted ( ndh ) or acquired point mutations ( cydA and cydB ), even if respiration was significantly reduced by these changes. Here, we obtained clean deletions of respiratory genes ndh and cydAB , individually and in combination, and showed, for the first time, that deletion of cydAB completely inhibited O 2 respiration and dramatically reduced growth in oxic conditions. Both respiration and aerobic growth were restored by expressing a heterologous, water-forming NADH oxidase, noxE . Oxygen can have many negative effects, including formation of reactive oxygen species (ROS) or directly inactivating oxygen sensitive enzymes. Our results suggest that the effect of molecular oxygen on enzymes had a greater negative impact on Z. mobilis than formation of ROS. This result shows that the main role of the electron transport chain in Z. mobilis is reducing the intracellular concentration of molecular oxygen, helping to explain why it is beneficial for Z. mobilis to use electron transport chain complexes that have little capacity to contribute to oxidative phosphorylation. IMPORTANCE A key to producing next-generation biofuels is to engineer microbes that efficiently convert non-food materials into drop-in fuels, and to engineer microbes effectively, we must understand their metabolism thoroughly. Zymomonas mobilis is a bacterium that is a promising candidate biofuel producer, but its metabolism remains poorly understood, especially its metabolism when exposed to oxygen. Although Z. mobilis respires with oxygen, its aerobic growth is poor, and disruption of genes related to respiration counterintuitively improves aerobic growth. This unusual result has sparked decades of research and debate regarding the function of respiration in Z. mobilis . Here, we used a new set of mutants to determine that respiration is essential for aerobic growth and likely protects the cells from damage caused by oxygen. We conclude that the respiratory pathway of Z. mobilis should not be deleted from chassis strains for industrial production because this would yield a strain that is intolerant of oxygen, which is more difficult to manage in industrial settings.

09 BIOMASS FUELS↗
DOE OSTI2023

Systems Engineering of Rhodococcus opacus to Enable Production of Drop-in Fuels from Lignocellulose

Production of drop-in fuels from lignocellulose using Rhodococcus opacus PD630 (hereafter R. opacus) is a challenging goal. During the grant period we have pushed the field forward significantly in several areas of research. Towards the end goal of accelerating the adoption of R. opacus in biofuel production, during the grant period we have expanded the phenotypic characterization of R. opacus grown in single aromatic (model lignocellulosic) compounds or their mixtures, modeling the growth conditions in lignocellulosic biomass. Harnessing the power of adaptive evolution, we produced evolved R. opacus isolates with superior lignin valorization capabilities and identified differentially expressed genes and pathways after adaptation. We used next generation multi-omic techniques such as genomic, transcriptomic, and metabolomic analyses, to identify the catabolic pathways used by R. opacus to degrade aromatic compounds and funnel these degradation products into central metabolism, as well as the aromatic transport genes required for increased tolerance and utilization. Taking this information one step further, we identified endogenous transcription factors and regulatory mechanisms important for degradation of five model aromatic compounds. To accurately estimate R. opacus growth and consumption on model lignin compounds we pioneered the use of novel extraction procedures prior to GC-MS analysis. Alongside 13 C-metabolic flux analysis, we have elucidated the metabolic routes preferred by Rhodococcus opacus during aromatic compound degradation. Finally, we used in tandem lipidomics and high-resolution mass spectrometry to identify the modulation of mycolic acids and phospholipid membrane composition modification as a strategy for aromatic tolerance in R. opacus. Being a non-model organism, R. opacus lacks the breadth of tools and technical foundation which drive biofuel research in more well-understood microbes such as Escherichia coli. To reduce this burden for use, we designed and produced new tools for genomic manipulation and engineering in R. opacus. These engineering breakthroughs support efficient genomic editing, enabling gene overexpression, repression, and genetic alteration. Using these tools, we have generated synthetically engineered strains with increased lipogenesis and growth, both positive traits required for increased lignin valorization. Optimizing engineered strains for biofuel production from lignocellulose requires extremely sophisticated synthetic rewiring of metabolism. To facilitate systems-level reorganization of metabolism in R. opacus, we created a genome-scale model that accurately predicts metabolic flux and growth rates on the aromatic compound phenol. Lignin requires extensive pre-treatment before biological degradation by R. opacus. Towards an eventual goal of degrading real-world lignin, we developed new depolymerization processes to generate lignin breakdown products (LBP). We optimized LBP storage and composition analysis techniques, enabling accurate prediction of specific LBP compound integration into cell wall components. Overall, through the work funded by this grant we generated 20 manuscripts (17 published, 3 in review/preparation), methods for increased accuracy in metabolomics of aromatic compounds, multiple genetic tools for altering the R. opacus genome, genome scale models for predicting flux through metabolic pathways, as well as multi-omic data for community use. The work funded by this grant has increased the knowledge of aromatic degradation in bacteria and advanced our efforts to optimize R. opacus for lignin valorization.

09 BIOMASS FUELS↗
DOE OSTI2022

Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered “Oilcane” Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper- accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane”. This study evaluates the potential of oilcane as a renewable feedstock for the co- production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. Here, this allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Data for Bioprocessing, Recovery, and Mass Balance of Vegetative Lipids from Metabolically Engineered ‘Oilcane’ Demonstrates Its Potential as an Alternative Feedstock for Drop-In Fuel Production

Plant oils are increasingly in demand as renewable feedstocks for biodiesel and biochemicals. Currently, oilseeds are the primary source of plant oils. Although the vegetative tissues of plants express lipid metabolism pathways, they do not hyper-accumulate lipids. Elevated synthesis, storage, and accumulation of lipids in vegetative tissues have been achieved by metabolic engineering of sugarcane to produce “oilcane.” This study evaluates the potential of oilcane as a renewable feedstock for the co-production of lipids and fermentable sugars. Oilcane was grown under favorable climatic and field conditions in Florida (FLOC) as well as during an abbreviated growing season, outside its typical growing region, in Illinois (ILOC). The potential lipid yield of 0.35 tons/ha was projected from the hyperaccumulation of fatty acids in the stored vegetative biomass of FLOC, which is approaching the lipid yield of soybean (0.44 tons/ha). Processing of the vegetative tissues of oilcane recovered 0.20 tons/ha, which represents the recovery of 55% of the total lipids from FLOC. Chemical-free hydrothermal bioprocessing of ILOC and FLOC bagasse and leaves at 180 °C for 10 min prevented the degeneration of in situ plant lipids. This allowed the recovery of lipids at the end of the bioprocess with a major fraction of lipids remaining in the biomass residues after pretreatment and saccharification. Improvements through refined biomass processing, crop management, and metabolic engineering are expected to boost lipid yields and make oilcane a prime feedstock for the production of biodiesel.

Conversion↗
DOE OSTI2023

Challenges and successes in establishing a multipurpose fuels and materials irradiation capsule [Slides]

This presentation discusses the challenges and success related to designing and fabricating multipurpose capsules for irradiation experiments for irradiation within the Advanced Test Reactor (ATR) to be presented at tje DEVICE-MTR irradiation experiment design working group meeting hosted by the Japanese Atomic Energy Agency (JAEA). The information herein is limited to the design of the capsules only and no programmatic information from any project supporting the design of the multipurpose capsule is discussed. The intent of the design team was establish a capsule design that could accommodate multiple different irradiation project needs for the irradiation of nuclear fuel and materials of interest in the nuclear field. The main points of the presentation are as follows: use of tin as a molten thermal bond material was selected for the fueled capsule design and was found to be inadequate as it would corrode the stainless steel at high temperatures, this capsule design has high sensitivity to manufacturing of the gas gap and control of the gas mixture, and the fueled capsule has experienced welding challenges with the inner capsule material 800H Incoloy.

42 ENGINEERING↗
DOE OSTI2026

Data for Resourceful and Economical Designing of Fermentation Medium for Lab and Commercial Strains of Yeast from Alternative Feedstock: Transgenic Oilcane

Sugarcane plant engineered to accumulate lipids in its vegetative tissue is being developed as a new bioenergy crop. The new crop would be a source of juice, oil, and cellulosic sugars. However, limited tolerance of industrially recognized yeasts towards inhibitors generated during the processing of lignocellulosic biomass to produce fermentable sugars is a major challenge in developing scalable processes for second-generation drop-in fuel production. To this end, hydrolysates generated from engineered sugarcane—‘oilcane’ bagasse contain added phenolics and fatty acids that further restrict the growth of fermenting microorganisms and necessitate nutrient supplementation and/or detoxification of hydrolysate which makes the fermentation process expensive. Herein, we propose a resourceful and economical approach for growing lab and commercial strains of S. cerevisiae on unrefined cellulosic sugars aerobically and fermentatively. An equal ratio of hydrolysate and juice was found optimum for growth and fermentation by lab and commercial strains of Saccharomyces cerevisiae engineered for xylose fermentation. The industrial strain grew and fermented efficiently under low aeration conditions having an ethanol titer, yield, specific and volumetric productivities of 46.96 ± 0.19 g/l, 0.51 ± 0.00 g/g, 0.27 ± 0.02 g/g.h and 1.95 ± 0.01 g/l.h, respectively, while the lab strain grew better under higher aeration conditions having the ethanol titer, yield, specific and volumetric productivities of 24.93 ± 0.09, 0.27 ± 0.00 g/g, 0.17 ± 0.00 g/g.h and 1.04 ± 0.00 g/l.h, respectively. Acclimation of cultures in a blended medium significantly improved the performance of the yeast strains. The addition of transgenic oilcane juice, which is inedible and rich in amino acids, to the hydrolysate averted the need for expensive nutrient supplementation and detoxification steps of hydrolysate. The approach provides an economical solution to reduce the cost of fermentation at an industrial scale for second-generation drop-in fuel production.

Biomass Analytics↗
DOE OSTI2021

Effects of detailed geometry and real fluid thermodynamics on Spray G atomization

We present recent results toward the quantification of spray characteristics at engine conditions for an eight-hole counter-bored (stepped) GDI injector-Spray G in the ECN denomination. This computational study is characterized by two novel features: the detailed description of a real injector's internal surfaces via tomographic reconstruction; and a general equation of state that represents the thermodynamic properties of homogeneous liquid-vapor mixtures. The combined level-set moment-of-fluid approach, coupled to an embedded boundary formulation for moving solid walls, makes it possible to seamlessly connect the injector's internal flow to the spray. The Large Eddy Simulation (LES) discussed here presents evidence of partial hydraulic flipping and, during the closing transient, string cavitation. Results are validated by measurements of spray density profiles and droplet size distribution.

42 ENGINEERING↗
DOE OSTI2023

Stabilizing a strongly nonlinear structure through shaker dynamics in fixed frequency voltage control tests

Bifurcations are commonly encountered during force controlled swept and stepped sine testing of nonlinear structures, which generally leads to the so-called jump-down or jump-up phenomena between stable solutions. There are various experimental closed-loop control algorithms, such as control-based continuation and phase-locked loop, to stabilize dynamical systems through these bifurcations, but they generally rely on specialized control algorithms that are not readily available with many commercial data acquisition software packages. A recent method was developed to experimentally apply sequential continuation using the shaker voltage that can be readily deployed using commercially available software. By utilizing the stabilizing effects of electrodynamic shakers and the force dropout phenomena in fixed frequency voltage control sine tests, this approach has been demonstrated to stabilize the unstable branch of a nonlinear system with three branches, allowing for three multivalued solutions to be identified within a specific frequency bandwidth near resonance. Recent testing on a strongly nonlinear system with vibro-impact nonlinearity has revealed jumping behavior when performing sequential continuation along the voltage parameter, like the jump phenomena seen during more traditional force controlled swept and stepped sine testing. Here, this paper investigates the stabilizing effects of an electrodynamic shaker on strongly nonlinear structures in fixed frequency voltage control tests using both numerical and experimental methods. The harmonic balance method is applied to the coupled shaker-structure system with an electromechanical model to simulate the fixed voltage control tests and predict the stabilization for different parameters of the model. The simulated results are leveraged to inform the design of a set of experiments to demonstrate the stabilization characteristics on a fixture-pylon assembly with a vibro-impact nonlinearity. Through numerical simulation and experimental testing on two different strongly nonlinear systems, the various parameters that influence the stability of the coupled shaker-structure are revealed to better understand the performance of fixed frequency voltage control tests.

42 ENGINEERING↗
DOE OSTI2021

Synthesis, antibiotic structure–activity relationships, and cellulose dissolution studies of new room-temperature ionic liquids derived from lignin

Ionic liquids (ILs) are promising pretreatment solvents for lignocellulosic biomass, but are largely prepared from petroleum precursors. Benzaldehydes from depolymerized lignin, such as vanillin, syringaldehyde, and 4-methoxy benzaldehyde, represent renewable feedstocks for the synthesis of ionic liquids. We herein report syntheses of novel lignin-derived ionic liquids, with extended N -alkyl chains, and examine their melting points, cellulose dissolution capacities, and toxicity profiles against Daphnia magna and E. coli strain 1A1. The latter organism has been engineered to produce isoprenol, a drop-in biofuel and precursor for commodity chemicals. The new N,N -diethyl and N,N -dipropyl methyl benzylammonium ILs were liquids at room temperature, showing 75–100 °C decreased melting points as compared to their N,N,N -trimethyl benzylammonium analog. Extension of N -alkyl chains also increased antibacterial activity threefold, while ionic liquids prepared from vanillin showed 2- to 4-fold lower toxicity as compared to those prepared from syringaldehyde and 4-methoxybenzaldehyde. The trend of antibacterial activity for anions of lignin-derived ILs was found to be methanesulfonate < acetate < hydroxide. Microcrystalline cellulose dissolution, from 2 to 4 wt% after 20 min at 100 °C, was observed in all new ILs using light microscopy and IR spectroscopy. Ionic liquids prepared from H-, S- and G-lignin oxidation products provided differential cytotoxic activity against E. coli and D. magna , suggesting these compounds could be tailored for application specificity within a biorefinery.

09 BIOMASS FUELS↗