Search NASA⌕ Search

SEARCH · Search NASA

Results for “ENTRY CONTROL SYSTEMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Pterodactyl: Control System Design for Deployable Entry Vehicles

As space exploration missions continue to get more complex, greater demands for mass and volume are being placed on planetary entry vehicles. At the same time, the desire for precision entry targeting to enable surface missions at very specific locations is becoming common. Deployable aeroshells are one type of technology that is being developed to increase the down-mass capability of planetary entry vehicles while complying with current launch vehicle volume constraints. Propulsive control can be used for precision entry targeting but can require a large percentage of the vehicle's total mass or volume for propellant. The Pterodactyl project is studying alternative entry control systems on a Deployable Entry Vehicle to potentially introduce a mass and volume efficient entry system that can achieve precision targeting. This paper presents the mechanical design work undertaken to support the Pterodactyl trade study of three entry vehicle control system options: 1) Flaps, 2) Mass Movement, and 3) Reaction Control System.

D'Souza, Sarah↗

Drag bias feedback for the analytic drag control entry guidance system

The Analytic Drag Control (ADC) entry guidance has been developed and baselined for the space shuttle orbiter entry. A method is presented which corrects the orbiter entry guidance commanded bank angle for biases between navigated drag and guidance computed reference drag. This is accomplished by an integral feedback technique, which uses the drag bias information to adjust the difference between navigated and reference altitude rate used by the ADC guidance. The method improves the capability of the ADC guidance system by compensating for any error source which causes a bias between the navigated drag and reference drag profile. These errors include navigated altitude rate errors, atmosphere dispersions, and roll attitude deadband effects. A discussion of the method and results of digital computer entry simulations is presented.

Kyle, H. C.↗

Entry flight control system downmoding evaluation

A method to desensitize the entry flight control system to structural vibration feedback which might induce an oscillatory instability is described. Trends in vehicle response and handling characteristics as a function of gain combinations in the FCS forward and rate feedback loops were described as observed in a man-in-the-loop simulation. Among the flight conditions considered are the effects of downmoding with APU failures, off-nominal trajectory conditions, sensed angle of attack errors, the impact on RCS fuel consumption, performance in the presence of aero variations, recovery from large FCS upsets, and default gains.

Barnes, H. A.↗

Entry Vehicle Control System Design for the Mars Smart Lander

The NASA Langley Research Center, in cooperation with the Jet Propulsion Laboratory, participated in a preliminary design study of the Entry, Descent and Landing phase for the Mars Smart Lander Project. This concept utilizes advances in Guidance, Navigation and Control technology to significantly reduce uncertainty in the vehicle landed location on the Mars surface. A candidate entry vehicle controller based on the Reaction Control System controller for the Apollo Lunar Excursion Module digital autopilot is proposed for use in the entry vehicle attitude control. A slight modification to the phase plane controller is used to reduce jet-firing chattering while maintaining good control response for the Martian entry probe application. The controller performance is demonstrated in a six-degree-of-freedom simulation with representative aerodynamics.

Calhoun, Philip C.↗

Entry reaction control system propellant analysis. Flight control integration

The effects of winds, sideslip angle feedback, and the data reference (air or inertial) on the Reaction Control System (RCS) propellant requirements during entry were investigated. It was determined that in the presence of a 3 sigma crosswind an addition 188 pounds of RCS propellant was required for entry control which is within the present 200 pound allotment for winds. The absence of air data information does result in slightly higher RCS propellant demands.

Devall, O. R.↗

Effect of aerodynamic and angle-of-attack uncertainties on the blended entry flight control system of the Space Shuttle from Mach 10 to 2.5

A six-degree-of-freedom simulation analysis has been performed for the Space Shuttle Orbiter during entry from Mach 10 to 2.5 with realistic off-nominal conditions using the entry flight control system specified in May 1978. The off-nominal conditions included the following: (1) aerodynamic uncertainties, (2) an error in deriving the angle of attack from onboard instrumentation, (3) the failure of two of the four reaction control-system thrusters on each side, and (4) a lateral center-of-gravity offset. With combinations of the above off-nominal conditions, the control system performed satisfactorily with a few exceptions. The cases that did not exhibit satisfactory performance displayed the following main weaknesses. Marginal performance was exhibited at hypersonic speeds with a sensed angle-of-attack error of 4 deg. At supersonic speeds the system tended to be oscillatory, and the system diverged for several cases because of the inability to hold lateral trim. Several system modifications were suggested to help solve these problems and to maximize safety on the first flight: alter the elevon-trim and speed-brake schedules, delay switching to rudder trim until the rudder effectiveness is adequate, and reduce the overall rudder loop gain. These and other modifications were incorporated in a flight-control-system redesign in May 1979.

Stone, H. W.↗

Analysis of Effectiveness of Phoenix Entry Reaction Control System

Interaction between the external flowfield and the reaction control system (RCS) thruster plumes of the Phoenix capsule during entry has been investigated. The analysis covered rarefied, transitional, hypersonic and supersonic flight regimes. Performance of pitch, yaw and roll control authority channels was evaluated, with specific emphasis on the yaw channel due to its low nominal yaw control authority. Because Phoenix had already been constructed and its RCS could not be modified before flight, an assessment of RCS efficacy along the trajectory was needed to determine possible issues and to make necessary software changes. Effectiveness of the system at various regimes was evaluated using a hybrid DSMC-CFD technique, based on DSMC Analysis Code (DAC) code and General Aerodynamic Simulation Program (GASP), the LAURA (Langley Aerothermal Upwind Relaxation Algorithm) code, and the FUN3D (Fully Unstructured 3D) code. Results of the analysis at hypersonic and supersonic conditions suggest a significant aero-RCS interference which reduced the efficacy of the thrusters and could likely produce control reversal. Very little aero-RCS interference was predicted in rarefied and transitional regimes. A recommendation was made to the project to widen controller system deadbands to minimize (if not eliminate) the use of RCS thrusters through hypersonic and supersonic flight regimes, where their performance would be uncertain.

Dyakonov, Artem A.↗

Effect of aerodynamic and angle-of-attack uncertainties on the May 1979 entry flight control system of the Space Shuttle from Mach 8 to 1.5

A six degree of freedom simulation analysis was performed for the space shuttle orbiter during entry from Mach 8 to Mach 1.5 with realistic off nominal conditions by using the flight control systems defined by the shuttle contractor. The off nominal conditions included aerodynamic uncertainties in extrapolating from wind tunnel derived characteristics to full scale flight characteristics, uncertainties in the estimates of the reaction control system interaction with the orbiter aerodynamics, an error in deriving the angle of attack from onboard instrumentation, the failure of two of the four reaction control system thrusters on each side, and a lateral center of gravity offset coupled with vehicle and flow asymmetries. With combinations of these off nominal conditions, the flight control system performed satisfactorily. At low hypersonic speeds, a few cases exhibited unacceptable performances when errors in deriving the angle of attack from the onboard instrumentation were modeled. The orbiter was unable to maintain lateral trim for some cases between Mach 5 and Mach 2 and exhibited limit cycle tendencies or residual roll oscillations between Mach 3 and Mach 1. Piloting techniques and changes in some gains and switching times in the flight control system are suggested to help alleviate these problems.

Stone, H. W.↗

Numerical Evaluation of Entry System Trajectory Control via Active Porosity Control of Transpiration Cooled Thermal Protection System

As space exploration expands, atmospheric descent requirements will tighten to improve landing accuracy to areas of interest. One way to meet higher landing accuracy requirements is by increasing vehicle maneuverability. This study explores the concept of manipulating a transpiration cooling scheme for entry capsules that could provide both active aerodynamic control as well as thermal protection for external surfaces. Numerical methods of fluid dynamics and heat transfer are presented to study the effectiveness of the concept in both thermal protection and entry vehicle attitude control. This effort works through development of an entry vehicle model at aeromaneuvering conditions with designated boundary activated for effects of transpiration cooling. Preliminary results show calculated values of heat flux and aerodynamic forces as a function of varying transpiration cooling flow rates. This contributes evidence of asymmetric cooling utilization as an additional mechanism for vehicle attitude control.

Caroline Anderson↗

The Development of the MSL Guidance, Navigation, and Control System for Entry, Descent, and Landing

On August 5, 2012, the Mars Science Laboratory (MSL) mission successfully delivered the Curiosity rover to its intended target. It was the most complex and ambitious landing in the history of the red planet. A key component of the landing system, the requirements for which were driven by the mission ambitious science goals, was the Guidance, Navigation, and Control (GN&C) system. This paper will describe the technical challenges of the MSL GN&C system, the resulting architecture and design needed to meet those challenges, and the development process used for its implementation and testing.

entry, descent, and landing.↗

The Development of the MSL Guidance, Navigation, and Control System for Entry, Descent, and Landing

On August 5, 2012, the Mars Science Laboratory (MSL) mission successfully delivered the Curiosity rover to its intended target. It was the most complex and ambitious landing in the history of the red planet. A key component of the landing system, the requirements for which were driven by the mission ambitious science goals, was the Guidance, Navigation, and Control (GN&C) system. This paper will describe the technical challenges of the MSL GN&C system, the resulting architecture and design needed to meet those challenges, and the development process used for its implementation and testing.

GN&C↗

Preliminary Study Using Forward Reaction Control System Jets During Space Shuttle Entry

Failure or degradation of the flight control system, or hull damage, can lead to loss of vehicle control during entry. Possible failure scenarios are debris impact and wing damage that could result in a large aerodynamic asymmetry which cannot be trimmed out without additional yaw control. Currently the space shuttle uses aerodynamic control surfaces and Reaction Control System jets to control attitude. The forward jets are used for orbital maneuvering only, while the aft jets are used for yaw control during entry. This paper develops a controller for using the forward reaction control system jets as an additional control during entry, and assesses its value and feasibility during failure situations. Forward-aft jet blending logic is created, and implemented on a simplified model of the space shuttle entry flight control system. The model is validated and verified on the nonlinear, six degree-of-freedom Shuttle Engineering Simulator. A rudimentary human factors study was undertaken using the forward cockpit simulator at Johnson Space Center, to assess flying qualities of the new system and pilot workload. Results presented in the paper show that the combination of forward and aft jets provides useful additional yaw control, in addition to potential fuel savings and the ability to balance the use of the fuel in the forward and aft tanks to meet availability constraints of both forward and aft fuel tanks. Piloted simulation studies indicated that using both sets of jets while flying a damaged space shuttle reduces pilot workload, and makes the vehicle more responsive.

Restrepo, Carolina↗

Pterodactyl: Non-Propulsive Control System Designs for Future Planetary Missions

Advances in deployable entry vehicle (DEV) technology, entry guidance, woven thermal protection systems, and affordable launch services make it possible to conceive of entry vehicles that optimize maneuverability, usable payload mass and volume, and operational costs. NASA's Space Technology Mission Directorate is currently funding the authors on a project, Pterodactyl, that is using on-the-fly trajectory design and integrated software and hardware development to investigate non-propulsive entry control systems for precision targeting of mechanical DEVs. The authors recently reported developments of these control systems for an asymmetric DEV to track bank commands for a lunar return entry. For this presentation, the authors will highlight key findings from their studies and propose rapid investigations of applications to future Mars missions such as sample return and asset delivery. Pterodactyl entry vehicle designs are suited to handle sensitive payloads and poised to achieve greater payload mass and volume compared to heritage entry vehicles given a particular launch vehicle. Furthermore, these designs could be adapted to launch on less costly launch vehicles as secondary payloads and could enable missions with high-frequency deployment requirements.

Alunni, Antonella↗

Effects of modifications to the space shuttle entry guidance and control systems

A nonlinear six degree of freedom entry simulation study was conducted to identify space shuttle guidance and control system software modifications which reduce the control system sensitivity to the guidance system sampling frequency. Several modifications which eliminated the control system sensitivity and associated control limit cycling were examined. The result of the modifications was a reduction in required reaction control system fuel.

Powell, R. W.↗

The pilot's role in manned space flight

The present investigation regarding the pilot's role in manned space flight takes into account space missions conducted with the Mercury capsule, Gemini, Apollo, Skylab, and the Shuttle. It is concluded that advancements in digital systems and automation technology have made many of the space pilot's tasks easier. However, these advancements have also made the space pilot's training more complicated. He must be familiar with the interrelated failure effects in highly complex vehicle systems. The nominal performance of the Shuttle fly-by-wire entry control system depends, for instance, on nominal electrical power from three fuel cells, nominal performance of three hydraulic auxiliary power units, five computers, other equipment, and microwave landing systems. The pilot must monitor and manage failures in these systems, and, in addition, must be prepared to intervene if an abort situation creates off-nominal conditions.

North, W. J.↗