Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Turbulence Measurements on a Flap-Edge Model

Turbulence measurements have been made on a flap-edge and leading-edge slat model using hot-wire anemometry, and, later, particle image velocimetry. The properties of hot-wire anemometry were studied using facilities at NASA Ames Research Center. Hot-film probes were used because of their durability, but cross-films were limited by non-linear end effects. As a warm-up exercise, hot-film probes were used to measure velocities in the farfield wake of a cylinder with an airfoil in the near-field wake. The airfoil reduced the drag coefficient of the system by 10%. A single-wire hot-film probe was used to measure velocity profiles over the top of a NACA 63(sub 2)-215 Mod. B wing with a Fowler flap and leading,-edge slat. Results showed the size of slat wake was dependent upon the slat deflection angle. Velocity increased through the slat gap with increased deflection. The acoustically modified slat decreased the chance of separation. Measurements were taken at the flap edge with a single hot-film. Trends in the data indicate velocity and turbulence levels increase at the flap edge. The acoustically modified flap modifies the mean flow near the flap edge. Correlations were made between the hot-film signal and the unsteady pressure transducers on the wing which were published in a NASA CDTM. The principles of Particle Image Velocimetry (PIV) were studied at Florida State University. Spectral PIV was used to measure the spectra of a subsonic jet. Measured frequencies were close to the predicted frequency of jet shedding. Spectral PIV will be used to measure the spectra of the slat flow in the second 7 x lO-ft. wind tunnel test. PIV has an advantage that it can measure velocity and spectra of the entire flowfield instantaneously. However, problems arise when trying, to store this massive amount of PIV data. Support for this research has continued through a NASA Graduate Student Program Fellowship which will end in June 1999. The thesis should be completed by this time.

Moriarty, Patrick↗

Numerical Predictions of Sonic Boom Signatures for a Straight Line Segmented Leading Edge Model

A sonic boom wind tunnel test was conducted on a straight-line segmented leading edge (SLSLE) model in the NASA Langley 4- by 4- Foot Unitary Plan Wind Tunnel (UPWT). The purpose of the test was to determine whether accurate sonic boom measurements could be obtained while continuously moving the SLSLE model past a conical pressure probe. Sonic boom signatures were also obtained using the conventional move-pause data acquisition method for comparison. The continuous data acquisition approach allows for accurate signatures approximately 15 times faster than a move-pause technique. These successful results provide an incentive for future testing with greatly increased efficiency using the continuous model translation technique with the single probe to measure sonic boom signatures. Two widely used NASA codes, USM3D (Navier-Stokes) and CART3D-AERO (Euler, adjoint-based adaptive mesh), were used to compute off-body sonic boom pressure signatures of the SLSLE model at several different altitudes below the model at Mach 2.0. The computed pressure signatures compared well with wind tunnel data. The effect of the different altitude for signature extraction was evaluated by extrapolating the near field signatures to the ground and comparing pressure signatures and sonic boom loudness levels.

Elmiligui, Alaa A.↗

Computational study of transition front on a swept wing leading-edge model

The e(N) method is employed with Navier-Stokes calculations to study 3D supersonic boundary layers at the leading-edge region of swept wings with attention given to the conditions for linear stability. Mean-flow profiles are computed as solutions to the Navier-Stokes equations, and the e(N) method is used to identify the onset of the transition. Specific treatment is given to the identification of parameters which affect the transition such as free-stream Reynolds number, wall cooling, and boundary-layer suction levels. The boundary layer can be stabilized to below N=10 levels in all locations by utilizing distributed suction, and enhanced stabilization can also be achieved by employing wall cooling and reduced free-stream Reynolds numbers. This study presents key calculations for corresponding experimental investigations by shedding light on requirements for test conditions and measurement requirements.

Iyer, Venkit↗

Downstream Effects on Orbiter Leeside Flow Separation for Hypersonic Flows

Discrepancies between experiment and computation for shuttle leeside flow separation, which came to light in the Columbia accident investigation, are resolved. Tests were run in the Langley Research Center 20-Inch Hypersonic CF4 Tunnel with a baseline orbiter model and two extended trailing edge models. The extended trailing edges altered the wing leeside separation lines, moving the lines toward the fuselage, proving that wing trailing edge modeling does affect the orbiter leeside flow. Computations were then made with a wake grid. These calculations more closely matched baseline experiments. Thus, the present findings demonstrate that it is imperative to include the wake flow domain in CFD calculations in order to accurately predict leeside flow separation for hypersonic vehicles at high angles of attack.

Buck, Gregory M.↗

Experimental Test Results of the Energy Efficient Transport (EET) Flap-Edge Vortex Model in the Langley Low-Turbulence Pressure Tunnel

This report presents the results of a test conducted in the Langley Low-Turbulence Pressure Tunnel to measure the flow field properties of a flap-edge vortex. The model was the EET (Energy Efficient Transport) Flap-Edge Vortex Model, which consists of a main element and a part-span, single-slotted trailing-edge flap. The model surface was instrumented with several chordwise and spanwise rows of pressure taps on each element. The off-body flow field velocities were to be measured in several planes perpendicular to the flap edge with a laser velocimetry system capable of measuring all three components in coincidence. However, due to seeding difficulties, the preliminary laser data did not have sufficient accuracy to be suitable for presentation; therefore, this report presents only the tabulated and plotted surface pressure data. In addition, the report contains a detail description of the model which can be used to generate accurate CFD grid structures.

Morgan, Harry L., Jr.↗

Transonic flight test of a laminar flow leading edge with surface excrescences

A flight experiment, conducted at NASA Dryden Flight Research Center, investigated the effects of surface excrescences, specifically gaps and steps, on boundary-layer transition in the vicinity of a leading edge at transonic flight conditions. A natural laminar flow leading-edge model was designed for this experiment with a spanwise slot manufactured into the leading-edge model to simulate gaps and steps like those present at skin joints of small transonic aircraft wings. The leading-edge model was flown with the flight test fixture, a low-aspect ratio fin mounted beneath an F-104G aircraft. Test points were obtained over a unit Reynolds number range of 1.5 to 2.5 million/ft and a Mach number range of 0.5 to 0.8. Results for a smooth surface showed that laminar flow extended to approximately 12 in. behind the leading edge at Mach number 0.7 over a unit Reynolds number range of 1.5 to 2.0 million/ft. The maximum size of the gap-and-step configuration over which laminar flow was maintained consisted of two 0.06-in. gaps with a 0.02-in. step at a unit Reynolds number of 1.5 million/ft.

Zuniga, Fanny A.↗

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 degrees to 35 degrees, 3. Effect of wing leading-edge modifications, model A

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the Langley spin tunnel are presented in plotted form for a 1/5 scale, single-engine, low-wing, general aviation airplane model. The configurations tested included the basic airplane, sixteen wing leading-edge modifications and lateral-directional control settings. Data are presented for all configurations without analysis for an angle of attack range of 8 deg to 35 deg and clockwise and counter-clockwise rotations covering an Omega b/2v range from 0 to 0.85. Also, data are presented above 35 deg of attack for some configurations.

Bihrle, W., Jr.↗

Thermal Edge-Effects Model for Automated Tape Placement of Thermoplastic Composites

Two-dimensional thermal models for automated tape placement (ATP) of thermoplastic composites neglect the diffusive heat transport that occurs between the newly placed tape and the cool substrate beside it. Such lateral transport can cool the tape edges prematurely and weaken the bond. The three-dimensional, steady state, thermal transport equation is solved by the Green's function method for a tape of finite width being placed on an infinitely wide substrate. The isotherm for the glass transition temperature on the weld interface is used to determine the distance inward from the tape edge that is prematurely cooled, called the cooling incursion Delta a. For the Langley ATP robot, Delta a = 0.4 mm for a unidirectional lay-up of PEEK/carbon fiber composite, and Delta a = 1.2 mm for an isotropic lay-up. A formula for Delta a is developed and applied to a wide range of operating conditions. A surprise finding is that Delta a need not decrease as the Peclet number Pe becomes very large, where Pe is the dimensionless ratio of inertial to diffusive heat transport. Conformable rollers that increase the consolidation length would also increase Delta a, unless other changes are made, such as proportionally increasing the material speed. To compensate for premature edge cooling, the thermal input could be extended past the tape edges by the amount Delta a. This method should help achieve uniform weld strength and crystallinity across the width of the tape.

Costen, Robert C.↗

Application of linear stability theory in laminar flow design

The linear stability of fully three-dimensional supersonic boundary layers formed over swept-wing configurations is investigated using a modified version of the linear stability code COSAL. Configurations studied include a highly swept leading-edge model to be utilized for transition studies in the LARC Low-disturbance Mach 3.5 Pilot Tunnel. The model is a representation of the leading edge of a laminar flow control wing for the F-16XL aircraft. In addition, the region over a laminar flow control glove fitted on the midportion of an F-16XL wing was studied. For each configuration, estimates of the location of the onset of transition were computed using linear stability theory and the e exp N method. The effectiveness of suction in stabilizing the boundary layer over the F-16XL wing glove was also investigated.

Iyer, Venkit↗

Active tectonics in southern Xinjiang, China: Analysis of terrace riser and normal fault scarp degradation along the Hotan-Qira fault system

The northern piedmont of the western Kunlun mountains (Xinjiang, China) is marked at its easternmost extremity, south of the Hotan-Qira oases, by a set of normal faults trending N50E for nearly 70 km. Conspicuous on Landsat and SPOT images, these faults follow the southeastern border of a deep flexural basin and may be related to the subsidence of the Tarim platform loaded by the western Kunlun northward overthrust. The Hotan-Qira normal fault system vertically offsets the piedmont slope by 70 m. Highest fault scarps reach 20 m and often display evidence for recent reactivations about 2 m high. Successive stream entrenchments in uplifted footwallls have formed inset terraces. We have leveled topographic profiles across fault scarps and transverse abandoned terrace risers. The state of degradation of each terrace edge has been characterized by a degradation coefficient tau, derived by comparison with analytical erosion models. Edges of highest abandoned terraces yield a degradation coefficient of 33 +/- 4 sq.m. Profiles of cumulative fault scarps have been analyzed in a similar way using synthetic profiles generated with a simple incremental fault scarp model.

Avouac, Jean-Philippe↗

Range data description based on multiple characteristics

An algorithm for describing range images based on Mean curvature (H) and Gaussian curvature (K) is presented. Range images are unique in that they directly approximate the physical surfaces of a real world 3-D scene. The curvature parameters are derived from the fundamental theorems of differential geometry and provides visible invariant pixel labels that can be used to characterize the scene. The sign of H and K can be used to classify each pixel into one of eight possible surface types. Due to the sensitivity of these parameters to noise the resulting HK-sing map does not directly identify surfaces in the range images and must be further processed. A region growing algorithm based on modeling the scene points with a Markov Random Field (MRF) of variable neighborhood size and edge models is suggested. This approach allows the integration of information from multiple characteristics in an efficient way. The performance of the proposed algorithm on a number of synthetic and real range images is discussed.

Al-Hujazi, Ezzet↗

Numerical Simulation of An Aspect Ratio 13.5 Common Research Model with Trailing Edge Mini-Flaps

This paper presents an aeroelastic modeling study of an aspect ratio 13.5 wind tunnel scale Common Research Model (CRM) with trailing edge mini-flaps. FUN3D is used for the aeroelastic steady and unsteady simulations at Mach 0.85 and dynamic pressure 230 psf. The aeroelastic simulation results are compared with the in-house developed VSPAERO aeroelastic model results. The incremental aerodynamic coefficients predicted by FUN3D and VSPAERO are close except when the mini-flap deflection angle is 10˚. The control reversal behavior is observed for the wing tip mini-flap. A series of dynamic pressure sweep simulations are performed to determine the control reversal onset point. Unsteady simulation results show that there is no buffet phenomenon observed at angle of attacks 0˚ and 2˚ when the mini-flap is deflected 10˚. The mini-flap oscillation simulations show the nonlinear behavior appears when the deflection angle is about 4˚.

Mini-flap↗

An edge-on galaxy model for Q 0957 + 561

An edge-on disk galaxy would act as a lens to produce two images which are aligned. Such a model would explain the observed features of Q0957 + 561A, and B. The third image is expected to be very faint and so neat to center of the lensing galaxy as to be unobservable.

Zheng, W.↗

Supporting Space Weather Modelling at the Community Coordinated Modeling Center (CCMC)

Space weather models are essential to our ability to understand and predict space weather events. Nonetheless, some of the most cutting-edge models may struggle to move past the initial research stage, remaining unknown and inaccessible to a wider research audience, thereby hindering validation, intercomparison and adoption of the models. The Community Coordinated Modeling Center (CCMC, https://ccmc.gsfc.nasa.gov) closes this gap by providing a convenient platform for hosting space weather models and associated services. Using these services, researchers and other end-users may exercise, evaluate, and intercompare contributed models, as well as collaborate on a growing archive of model run results. In this presentation, we will discuss current and planned capabilities in some of the model services at CCMC, including Runs-on-Request, Instant Runs, and Real-Time Continuous Runs. We will also review new models added to the extensive collection of space weather models hosted at CCMC. Finally, we will talk about our efforts at streamlining model delivery to CCMC, including support for containerized models and establishment of an open collaborative environment based on Amazon Web Services (AWS).

space weather↗

Forced and Moment Measurements with Pressure-Sensitive Paint

The potential of pressure-sensitive paint (PSP) to provide aerodynamic loads measurements has been a driving force behind the development of this measurement technique. To demonstrate the suitability of PSP for this purpose, it is necessary to show that PSP-derived pressures can be accurately integrated over the model surface. This cannot be done simply by demonstrating the accuracy of PSP as compared to pressure taps. PSP errors due to misregistration or temperature sensitivity may be high near model edges, where they will have a strong effect on moment measurements, but where pressure taps are rarely installed. A more suitable technique is to compare integrated PSP data over the entire model surface with balance and/or CFD results. This paper presents results from three experiments in which integrated PSP data is compared with balance and/or CFD data. This allows the usefulness of PSP for force and moment measurements, and by implication for loads measurements, to be assessed.

Bell, James H.↗

Modeling the Influence of Stitching on Delamination Growth in Stitched Warp-Knit Composite Lap Joints

The effect of stitches on the failure of a single lap joint configuration was determined in a combined experimental and analytical study. The experimental study was conducted to determine debond growth under static monotonic loading. The stitches were shown to delay the initiation of the debond and provide load transfer beyond the load necessary to completely debond the stitched lap joint. The strain energy release rates at the debond front were calculated using a finite element-based technique. Models of the unstitched configuration showed significant values of modes I and II across the width of the joint and showed that mode III is zero at the centerline but increases near the free edge. Models of the stitched configuration showed that the stitches effectively reduced mode I to zero, but had less of an effect on modes II and III.

Glaessgen, E. H.↗

Debonding of Stitched Composite Joints: Testing and Analysis

The effect of stitches on the failure of a single lap joint configuration was determined in a combined experimental and analytical study. The experimental study was conducted to determine debond growth under static monotonic loading. The stitches were shown to delay the initiation ofthe debond and provide load transfer beyond the load necessary to completely debond the stitched lap joint. The strain energy release rates at the debond front were calculated using a finite element-based technique. Models of the unstitched configuration showed significant values of modes I and II across the width of the joint and showed that mode III is zero at the centerline but increases near the free edge. Models of the stitched configuration showed that the stitches effectively reduced mode I to zero, but had less of an effect on modes II and III.

Glaessgen, E. H.↗