Search NASA⌕ Search

SEARCH · Search NASA

Results for “Effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

The Empirical Effect of Fleet Optimization on Synchronization and Rebound Effects in Heat Pump Water Heaters

Demand response is a growing concept in light of the internet of things and an increasing need for grid flexibility. Water heaters are one of the preferred devices for providing demand response for grid services and peak management due to their capability to store energy. The efficient use of water heaters for demand response requires consideration of the associated load effects such as synchronization of device schedules and rebound effect. These effects present a significant challenge. Despite the importance of the mentioned effects for water heater queuing and scheduling, there has been no effort to quantify and empirically validate their impact. This study attempts to address this gap by offering two methods - Ward clustering and Euclidean K-means - to evaluate the extent of synchronization in a fleet of 42 water heaters in Atlanta, GA. Using the aforementioned methods on the measured data, we find evidence of convergence of water heater loads as a result of optimization compared to an idle period and analyzed their impact.

demand response↗
DOE OSTI2021

Topological Nernst effect, anomalous Nernst effect, and anomalous thermal Hall effect in the Dirac semimetal Fe 3 Sn 2

Topological semimetals have been a focal point of research in recent years. One of the salient characters of topological semimetals is the anomalous Hall effect arising from the nontrivial momentum-space Berry phase. In contrast, anomalous transverse thermoelectric coefficient and thermal Hall effect are much less explored up to date. In this paper, we report thermoelectric and thermal transport properties of Fe 3 Sn 2 , a prototypical Dirac semimetal. We find that Fe 3 Sn 2 exhibits large topological Nernst effect which is associated with the non-zero spin chirality of the skyrmion bubble phase. Furthermore, Fe 3 Sn 2 shows prominent anomalous thermal Hall effect and anomalous Nernst effect with features similar to the anomalous Hall effect. The anomalous Nernst signal is about 2.1 μV/K at room temperature, which is comparable to the largest value reported thus far. These results highlight the synergic effects of Berry phase in both real space and momentum space of Fe 3 Sn 2 , and this study demonstrates an effective strategy of investigating topological materials by measuring their transverse thermal and thermoelectric responses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Drying model of a high salt content cementitious waste form: Effect of capillary forces and salt solution

Highlights: • Drying model for a high salt content cementitious waste form is developed. • Water vapor diffusion and capillary liquid flow are distinguished. • Capillary and salt solution effects are considered in vapor-liquid equilibrium. A water transport model coupling capillary liquid flow with vapor diffusion is developed to describe the drying process for a cementitious waste form with high salinity porewater. Vapor-liquid equilibrium is formulated as the driving force for vapor diffusion and the model accounts for pore capillary and high salinity effects on water thermodynamic activity. Pore filling and porewater surface tension as a function of pore size distribution and water saturation have been quantified for the material. Geochemical speciation modeling is used to simulate porewater activity as a function of composition over the range of saturation. The theoretical relationship between relative humidity and water saturation generally agrees with experimental measurement, and the developed model is capable of predicting drying rates under various external relative humidity conditions. The model was developed to be incorporated into reactive transport models considering the effects of drying such as salt redistribution and efflorescence.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of Farm-to-Farm Interactions and Blockage Effects from AWAKEN using Large-Scale Numerical Simulations

A large-scale numerical computation of five wind farms was performed as a part of the American Wake Experiment (AWAKEN). This high-fidelity computation used the ExaWind/AMR-Wind LES solver to simulate a 100km × 100km domain containing 541 turbines under unstable atmospheric conditions matching previous measurements. The turbines were represented by Joukowski and OpenFAST coupled actuator disk models. Results of this qualitative comparison illustrate the interactions with wind farms with large scale ABL structures in the flow, as well as the extent of downstream wake penetration in the flow and blockage effects around wind farms.

Cheung, Lawrence C.↗
DOE OSTI2021

Effects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part I: Physical properties

Understanding composition-structure-property relationships of high-alumina nuclear waste glasses are important for vitrification of nuclear waste at the Hanford Site. Two series of glasses were designed, one with varying Al:Si ratios and the other with (Al+Na):Si ratios based on the International Simple Glass (ISG, a simplified nuclear waste model glass), with Al2O3 ranging from 0 to 23 mol % (0 to 32 wt. %). The glasses were synthesized and characterized using electron probe microanalysis, X-ray photoelectron spectroscopy, small angle X-ray scattering, high temperature oxide melt solution calorimetry, and infrared spectroscopy. Glasses were crystal free, and the lowest Na2O and Al2O3 glass formed an immiscible glass phase. Evolution of various properties - glass transition temperature, percentage of 4-coordinated B, enthalpy of glass formation - and infrared spectroscopy results indicate that structural effects differ based on the glass series.

Nuclear Waste Glass↗
DOE OSTI2020

The effect of lighting environment on task performance in buildings – A review

The effects of indoor environmental conditions on human health, satisfaction, and performance have been the focal point of research for decades. This paper reviews and summarizes the impact of lighting environment on task performance, specifically for the built environment audience. Existing studies included a variety of performance tests on cognitive performance and perception, visual acuity and reaction, memory, reasoning, and labor productivity. Illuminance, luminance ratio and correlated color temperature were found to affect performance in different ways, reflecting the impact of experimental techniques, conditions, performance evaluation methods used and data analysis methods. These were reviewed and categorized, with discussion on limitations related to sample size, modeling approach, carryover effects and other factors affecting individual differences in performance, with recommendations for future improvement. Although no universal conclusions can be made, in general, task performance seems to improve with higher illuminances, contrast ratios in the range of 7–11:1 (while always making sure that glare will not occur in the space) and higher correlated color temperature, while spectral tuning in the red or blue wavelengths has also shown positive effects. To obtain more generic evidence, future studies should be more consistent in terms of experimental procedures and overall light conditions, and also consider the effects of vertical illuminance, daylight provision/control, and outside views on task performance. Finally, studying performance with multi-factorial designs in a human-centered optimized manner (such as deploying variable lighting scenarios optimized for various tasks) can lead to deeper understanding of lighting effects on task performance, and ultimately to improved lighting design and operation in buildings overall.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Isotope effects on transport in LHD

Abstract Isotope effects are one of the most important issues for predicting future reactor operations. Large helical device (LHD) is the presently working largest stellarator/helical device using super conducting helical coils. In LHD, deuterium experiments started in 2017. Extensive studies regarding isotope effects on transport have been carried out. In this paper, the results of isotope effect studies in LHD are reported. The systematic studies were performed adjusting operational parameters and nondimensional parameters. In L mode like normal confinement plasma, where internal and edge transport barriers are not formed, the scaling of global energy confinement time ( τ E ) with operational parameters shows positive mass dependence ( M 0.27 ; where M is effective ion mass) in electron cyclotron heating plasma and no mass dependence ( M 0.0 ) in neutral beam injection heating plasma. The non-negative ion mass dependence is anti-gyro-Bohm scaling. The role of the turbulence in isotope effects was also found by turbulence measurements and gyrokinetic simulation. Better accessibility to electron and ion internal transport barrier (ITB) plasma is found in deuterium (D) plasma than in hydrogen (H). Gyro kinetic non-linear simulation shows reduced ion heat flux due to the larger generation of zonal flow in deuterium plasma. Peaked carbon density profile plays a prominent role in reducing ion energy transport in ITB plasma. This is evident only in plasma with deuterium ions. New findings on the mixing and non-mixing states of D and H particle transports are reported. In the mixing state, ion particle diffusivities are higher than electron particle diffusivities and D and H ion density profiles are almost identical. In the non-mixing state, ion particle diffusivity is much lower than electron diffusivity. Deuterium and hydrogen ion profiles are clearly different. Different turbulence structures were found in the mixing and non-mixing states suggesting different turbulence modes play a role.

Physics↗
DOE OSTI2023

Effect of Blown Powder Directed Energy Deposition Angle On Overspray Contamination

Abstract Blown powder directed energy deposition (DED) hybrid machine tools are particularly beneficial when the net shape of a component is to be manufactured in an additive and machined interleaved fashion. This investigation seeks to analyze the effect of the additive head lean angle relative to the part on blown powder DED surface contamination due to overspray. These hybrid DED platforms are commonly installed on multi-axis machining systems where the lean of the deposition head relative to the component surface can be controlled by tilting the component. The blown powder DED process has a 10–50% lower catchment efficiency as compared to wire fed DED systems. This excess powder is still fed towards the deposition location where the particles are heated by the laser and rebound off the melt pool. Some of these heated particles impact the previously machined thin-wall surface. While the deposition process and tool path planning process has been evaluated, the effect of the overspray due to lean angle of the deposition head on the previously thin-wall machined surface is not yet fully understood. This investigation found that minimum lean angle coincides with minimal overspray effect with nearly no contamination. If a lean angle is required, the maximum lean angle possible should be implemented for the smallest effected overspray area on the machined surface which was found to decrease the affect zone by half compared to intermediate lean angles. A diameter divergence was also noticed as the deposition angle was increased. In this study, a thorough analysis of the surface and geometric effects when depositing thin-walled components at varying angles is completed. It has been shown that part quality can be significantly affected by lean angle and thus must be incorporated as an additional design consideration in the manufacturing process.

Heinrich, Lauren↗
DOE OSTI2020

Measurement of space charge effects in the MicroBooNE LArTPC using cosmic muons

Large liquid argon time projection chambers (LArTPCs), especially those operating near the surface, are susceptible to space charge effects. In the context of LArTPCs, the space charge effect is the build-up of slow-moving positive ions in the detector primarily due to ionization from cosmic rays, leading to a distortion of the electric field within the detector. This effect leads to a displacement in the reconstructed position of signal ionization electrons in LArTPC detectors ("spatial distortions"), as well as to variations in the amount of electron-ion recombination experienced by ionization throughout the volume of the TPC. We present techniques that can be used to measure and correct for space charge effects in large LArTPCs by making use of cosmic muons, including the use of track pairs to unambiguously pin down spatial distortions in three dimensions. Finally, the performance of these calibration techniques are studied using both Monte Carlo simulation and MicroBooNE data, utilizing a UV laser system as a means to estimate the systematic bias associated with the calibration methodology.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

The effect of building retrofit measures on CO2 emission reduction – A case study with U.S. Medium office buildings

Building retrofit has great potential to reduce CO2 emissions since buildings are responsible for 36% of emissions in the United States. Several existing studies have examined the effect of building retrofit measures on CO2 emission reduction. However, these studies oversimplified emission factors of electricity by adopting constant annual emission factors. This study uses hourly emission factors of electricity to analyze the effect of building retrofit measures on emission reduction using U.S. medium office buildings as an example. We analyzed CO2 emission reduction effects of eight building retrofit measures that related to envelop and mechanical system in five locations: Tampa, San Diego, Denver, Great Falls, and International Falls. The main findings are: (1) estimating CO2 emission reduction with constant emission factors overestimates the emission reduction for most measures in San Diego, while it underestimates the emission reduction for most measures in Denver and International Falls; (2) The same retrofit measure may have different effects in CO2 emission reduction depending on the climates. For instance, improving lighting efficiency and improving equipment efficiency have less impacts in emission reduction in cold climates than hot climates; and (3) The most energy efficient measure may not be the most emission efficient measure. For example, in Great Falls, the most energy efficient measure is improving equipment efficiency, but the most emission efficient measure is improving heating efficiency.

Lou, Yingli↗
DOE OSTI2023

Revisiting proton–proton fusion in chiral effective field theory

We calculate the S-factor for proton–proton fusion using chiral effective field theory interactions and currents. By performing order-by-order calculations with a variety of chiral interactions that are regularized and calibrated in different ways, we assess the uncertainty in the S-factor from the truncation of the effective field theory expansion and from the sensitivity of the S-factor to the short-distance axial current determined from three- and four-nucleon observables. We find that S(0) = (4.100 ± 0.024(syst) ± 0.013(stat) ± 0.008(g$_{A}$)) × 10$^{−23}$ MeV fm$^{2}$, where the three uncertainties arise, respectively, from the truncation of the effective field theory expansion, use of the two-nucleon axial current fit to few-nucleon observables and variation of the axial coupling constant within the recommended range. The increased value of S(0) compared to previous calculations is mainly driven by an increase in the recommended value for the axial coupling constant and is in agreement with a recent analysis based on pionless effective field theory.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2022

Cross-correlation of Dark Energy Survey Year 3 lensing data with ACT and P l a n c k thermal Sunyaev-Zel’dovich effect observations. II. Modeling and constraints on halo pressure profiles

Hot, ionized gas leaves an imprint on the cosmic microwave background via the thermal Sunyaev-Zel’dovich (tSZ) effect. The cross-correlation of gravitational lensing (which traces the projected mass) with the tSZ effect (which traces the projected gas pressure) is a powerful probe of the thermal state of ionized baryons throughout the Universe and is sensitive to effects such as baryonic feedback. In a companion paper (Gatti et al. Phys. Rev. D 105, 123525 (2022)), we present tomographic measurements and validation tests of the cross-correlation between Galaxy shear measurements from the first three years of observations of the Dark Energy Survey and tSZ measurements from a combination of Atacama Cosmology Telescope and Planck observations. In this work, we use the same measurements to constrain models for the pressure profiles of halos across a wide range of halo mass and redshift. We find evidence for reduced pressure in low-mass halos, consistent with predictions for the effects of feedback from active Galactic nuclei. We infer the hydrostatic mass bias (B ≡ M 500c /M SZ from our measurements, finding B = 1.8 ± 0.1 when adopting the Planck-preferred cosmological parameters. We additionally find that our measurements are consistent with a nonzero redshift evolution of B, with the correct sign and sufficient magnitude to explain the mass bias necessary to reconcile cluster count measurements with the Planck-preferred cosmology. Our analysis introduces a model for the impact of intrinsic alignments (IAs) of galaxy shapes on the shear-tSZ correlation. We show that IA can have a significant impact on these correlations at current noise levels.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

Predicting Drug Effects from High-dimensional Asymmetric Drug Data Sets using Graph Neural Networks: A Comprehensive Analysis of Multi-target Drug Effect Prediction

Graph neural networks (GNNs) have emerged as one of the most effective Machine learning (ML) techniques for drug effect prediction from drug molecular graphs. Despite having immense potential, GNN models lack performance when using data sets that contain high dimensional asymmetrically co-occurrent drug effects as targets with complex correlations between them. Training individual learning models for each drug effect and incorporating every prediction result for a wide spectrum of drug effects is beyond practicality. Such an implication provides a testbed to address this challenge as multi-target prediction problems, aiming to predict all drug effects at a time. We develop standard and hybrid graph neural networks (GNNs)to perform two separate tasks that are multi-regression for continuous values and multi-label classification for categorical values contained in our data sets. Since this step makes the target data even more sparse and introduces asymmetric label co-occurrence, the learning of multi-label classification models becomes difficult and heavily impacts the GNN's performance. To address these challenges, we propose a new data oversampling technique to improve multi-label classification performances on all the given imbalanced molecular graph data sets. Using the technique, we improve the data imbalance ratio of the drug effects better than before while protecting the data set's integrity. Finally, we evaluate multi-label classification performance using the best-performant hybrid GNN model on all the oversampled data sets obtained from the proposed oversampling technique. These results outperform those of other ML models including GNN models when they are trained on the original data sets or oversampled data sets using MLSMOTE (a well-known oversampling technique) in all evaluation metrics precision, recall, and F1 score by a significant margin.

Bose, Avishek [ORNL]↗
DOE OSTI2021

Chiral Effective Field Theory and the High-Density Nuclear Equation of State

Born in the aftermath of core-collapse supernovae, neutron stars contain matter under extraordinary conditions of density and temperature that are difficult to reproduce in the laboratory. In recent years, neutron star observations have begun to yield novel insights into the nature of strongly interacting matter in the high-density regime where current theoretical models are challenged. At the same time, chiral effective field theory has developed into a powerful framework to study nuclear matter properties with quantified uncertainties in the moderate-density regime for modeling neutron stars. In this article, we review recent developments in chiral effective field theory and focus on many-body perturbation theory as a computationally efficient tool for calculating the properties of hot and dense nuclear matter. We also demonstrate how effective field theory enables statistically meaningful comparisons among nuclear theory predictions, nuclear experiments, and observational constraints on the nuclear equation of state.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗