Search NASA⌕ Search

SEARCH · Search NASA

Results for “Elast Perfectly Plastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Application Of Elastic Perfectly Plastic Cyclic Analysis To Assessment Of Creep Strain

A cyclic elastic-perfectly plastic analysis method is proposed which provides a conservative estimate to cyclic creep strain accumulation within the ratchet boundary. The method is to check for ratcheting based on an elastic-perfectly material with a temperature-dependent pseudo yield stress defined by temperature, time and stress to give 1% creep strain. It does not require stress classification and is also applicable to a full range of temperature above and below the creep regime. This simplified method could be used as a rapid screening calculation, with full time-dependent creep analysis used if necessary.

Carter, Peter↗

An elastic-perfectly plastic analysis of the bending of the lithosphere at a trench

A number of authors have modeled the flexure of the lithosphere at an oceanic trench using a thin elastic plate with a hydrostatic restoring force. In some cases good agreement with observed topography is obtained but in other cases the slope of the lithosphere within the trench is greater than that predicted by the elastic theory. In this paper the bending of a thin plate is considered using an elastic-perfectly plastic rheology. It is found that the lithosphere behaves elastically seaward of the trench, but that plasticity decreases the radius of curvature within the trench. The results are compared with a number of observed trench profiles. The elastic-perfectly plastic profiles are in excellent agreement with those profiles that deviate from elastic behavior.

Turcotte, D. L.↗

Axisymmetric micromechanics of elastic-perfectly plastic fibrous composites under uniaxial tension loading

The uniaxial response of a continuous fiber elastic-perfectly plastic composite is modeled herein as a two-element composite cylinder. An axisymmetric analytical micromechanics solution is obtained for the rate-independent elastic-plastic response of the two-element composite cylinder subjected to tensile loading in the fiber direction for the case wherein the core fiber is assumed to be a transversely isotropic elastic-plastic material obeying the Tsai-Hill yield criterion, with yielding simulating fiber failure. The matrix is assumed to be an isotropic elastic-plastic material obeying the Tresca yield criterion. It is found that there are three different circumstances that depend on the fiber and matrix properties: fiber yield, followed by matrix yielding; complete matrix yield, followed by fiber yielding; and partial matrix yield, followed by fiber yielding, followed by complete matrix yield. The order in which these phenomena occur is shown to have a pronounced effect on the predicted uniaxial effective composite response.

Lee, Jong-Won↗

Dynamic fields near a crack tip growing in an elastic-perfectly-plastic solid

A full asymptotic solution is presented for the fields in the neighborhood of the tip of a steadily advancing crack in an incompressible elastic-perfectly-plastic solid. There are four findings for mode I crack growth in the plane strain condition. The first is that the entire crack tip in steady crack growth is surrounded by a plastic region and that no elastic unloading is predicted by the complete dynamic asymptotic solution. The second is that, in contrast to the quasi-static solution, the dynamic solution yields strain fields with a logarithmic singularity everywhere near the crack tip. The third is that whereas the stress field varies throughout the entire crack tip neighborhood, it does not exhibit behavior that can be approximated by a constant field followed by an essentially centered-fan field and then by another constant field, especially for small crack growth speeds. The fourth finding is that there are two shock fronts emanating from the crack tip across which certain stress and strain components undergo jump discontinuities. After reviewing the mode III steady-state crack growth, it is concluded that ductile fracture criteria for nonstationary cracks must be based on solutions that include the inertia effects and that for this purpose quasi-static solutions may be inadequate.

Nemat-Nasser, S.↗

Comprehensive Report For Proposed Elevated Temperature Elastic Perfectly Plastic (EPP) Code Cases Representative Example Problems

Background: The current rules in the nuclear section of the ASME Boiler and Pressure Vessel (B&PV) Code , Section III, Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200F (650C)1. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (E-PP) analysis methods and which are expected to be applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature 2, 3, and have been recently revised to incorporate comments and simplify their application. The revised code cases have been developed. Task Objectives: The goal of the Sample Problem task is to exercise these code cases through example problems to demonstrate their feasibility and, also, to identify potential corrections and improvements should problems be encountered. This will provide input to the development of technical background documents for consideration by the applicable B&PV committees considering these code cases for approval. This task has been performed by Hollinger and Pease of Becht Engineering Co., Inc., Nuclear Services Division and a report detailing the results of the E-PP analyses conducted on example problems per the procedures of the E-PP strain limits and creep-fatigue draft code cases is enclosed as Enclosure 1. Conclusions: The feasibility of the application of the E-PP code cases has been demonstrated through example problems that consist of realistic geometry (a nozzle attached to a semi-hemispheric shell with a circumferential weld) and load (pressure; pipe reaction load applied at the end of the nozzle, including axial and shear forces, bending and torsional moments; through-wall transient temperature gradient) and design and operating conditions (Levels A, B and C).

36 MATERIALS SCIENCE↗

Elevated Temperature Primary Load Design Method Using Pseudo Elastic-Perfectly Plastic Model

A new primary load design method for elevated temperature service has been developed. Codification of the procedure in an ASME Boiler and Pressure Vessel Code, Section III Code Case is being pursued. The proposed primary load design method is intended to provide the same margins on creep rupture, yielding and creep deformation for a component or structure that are implicit in the allowable stress data. It provides a methodology that does not require stress classification and is also applicable to a full range of temperature above and below the creep regime. Use of elastic-perfectly plastic analysis based on allowable stress with corrections for constraint, steady state stress and creep ductility is described. This approach is intended to ensure that traditional primary stresses are the basis for design, taking into account ductility limits to stress re-distribution and multiaxial rupture criteria.

Carter, Peter↗

Initial development and verification of a primary load design method based on elastic-perfectly plastic analysis

This report describes a new primary load design method to supplement the current design-by-elastic-analysis rules in Section III, Division 5, Subsection HB, Subpart B of the ASME Boiler and Pressure Vessel Code, covering the design and construction of Class A high temperature nuclear structural components. The main objectives for the new design method are to provide a procedure that can be applied to components with complicated geometries and to simplify the primary load design process by providing rules more compatible with modern finite element analysis. The report includes a complete set of design rules, presented as a draft ASME Code Case, as well as a commentary on the rules and a set of verification problems. The verification design problems demonstrate the new primary load design rules produce safe, efficient components when compared to the current Division 5 approach, while greatly simplifying the design analysis process.

42 ENGINEERING↗

A basis for applying elastic perfectly-plastic design methods to cyclic softening materials

Design approaches using elastic perfectly-plastic (EPP) analysis have recently been approved as Code Cases for the Section III, Division 5 design of high-temperature nuclear reactor components made from austenitic stainless steel. These methods bound the ratcheting strain and creep-fatigue damage accumulated over the life of a component with a simplified, elastic perfectly plastic analysis using a special pseudo-yield stress often not equal to the true material yield stress. The austenitic materials specified in the existing Code cases are cyclic-hardening for all allowable operating temperatures. However, other Section III, Division 5 materials, such as Grade 91 steel, are cyclic softening at expected advanced reactor operating temperatures. This work describes the extension of EPP methods to cyclic softening materials through the use of a postulated saturated material state and softening factors to be applied to the pseudo yield stress. We demonstrate the conservatism of the modified EPP method against a series of inelastic simulations of two bar tests, using a constitutive model that captures work and cyclic softening.

Messner, M. C.↗

A BASIS FOR APPLYING ELASTIC PERFECTLY-PLASTIC DESIGN METHODS TO CYCLIC SOFTENING MATERIALS

Design approaches using elastic perfectly-plastic (EPP) analysis have recently been approved as Code Cases for the Section III, Division 5 design of high-temperature nuclear reactor components made from austenitic stainless steel. These methods bound the ratcheting strain and creep-fatigue damage accumulated over the life of a component with a simplified, elasticperfectly plastic analysis using a special pseudo-yield stress – often not equal to the true material yield stress. The austenitic materials specified in the existing Code cases are cyclic-hardening for all allowable operating temperatures. However, other Section III, Division 5 materials, such as Grade 91 steel, are cyclic softening at expected advanced reactor operating temperatures. This work describes the extension of EPP methods to cyclic softening materials through the use of a postulated saturated material state and softening factors to be applied to the pseudo yield stress. We demonstrate the conservatism of the modified EPP method against a series of inelastic simulations of two bar tests, using a constitutive model that captures work and cyclic softening.

Messner, Mark C.↗

DYCAST: A finite element program for the crash analysis of structures

DYCAST is a nonlinear structural dynamic finite element computer code developed for crash simulation. The element library contains stringers, beams, membrane skin triangles, plate bending triangles and spring elements. Changing stiffnesses in the structure are accounted for by plasticity and very large deflections. Material nonlinearities are accommodated by one of three options: elastic-perfectly plastic, elastic-linear hardening plastic, or elastic-nonlinear hardening plastic of the Ramberg-Osgood type. Geometric nonlinearities are handled in an updated Lagrangian formulation by reforming the structure into its deformed shape after small time increments while accumulating deformations, strains, and forces. The nonlinearities due to combined loadings are maintained, and stiffness variation due to structural failures are computed. Numerical time integrators available are fixed-step central difference, modified Adams, Newmark-beta, and Wilson-theta. The last three have a variable time step capability, which is controlled internally by a solution convergence error measure. Other features include: multiple time-load history tables to subject the structure to time dependent loading; gravity loading; initial pitch, roll, yaw, and translation of the structural model with respect to the global system; a bandwidth optimizer as a pre-processor; and deformed plots and graphics as post-processors.

Pifko, A. B.↗

A Progressive Damage Methodology for Residual Strength Predictions of Center-Crack Tension Composite Panels

An investigation of translaminate fracture and a progressive damage methodology was conducted to evaluate and develop a residual strength prediction capability for laminated composites with through penetration notches. This is relevant to the damage tolerance of an aircraft fuselage that might suffer an in-flight accident such as an uncontained engine failure. An experimental characterization of several composite materials systems revealed an R-curve type of behavior. Fractographic examinations led to the postulate that this crack growth resistance could be due to fiber bridging, defined here as fractured fibers of one ply bridged by intact fibers of an adjacent ply. The progressive damage methodology is currently capable of predicting the initiation and growth of matrix cracks and fiber fracture. Using two difference fiber failure criteria, residual strength was predicted for different size panel widths and notch lengths. A ply discount fiber failure criterion yielded extremely conservative results while an elastic-perfectly plastic fiber failure criterion showed that the fiber bridging concept is valid for predicting residual strength for tensile dominated failure loads. Furthermore, the R-curves predicted by the model using the elastic-perfectly plastic fiber criterion compared very well with the experimental R-curves.

Coats, Timothy William↗

FY16 Status Report on Development of Integrated EPP and SMT Design Methods

The goal of the Elastic-Perfectly Plastic (EPP) combined integrated creep-fatigue damage evaluation approach is to incorporate a Simplified Model Test (SMT) data based approach for creep-fatigue damage evaluation into the EPP methodology to avoid the separate evaluation of creep and fatigue damage and eliminate the requirement for stress classification in current methods; thus greatly simplifying evaluation of elevated temperature cyclic service. The EPP methodology is based on the idea that creep damage and strain accumulation can be bounded by a properly chosen “pseudo” yield strength used in an elastic-perfectly plastic analysis, thus avoiding the need for stress classification. The original SMT approach is based on the use of elastic analysis. The experimental data, cycles to failure, is correlated using the elastically calculated strain range in the test specimen and the corresponding component strain is also calculated elastically. The advantage of this approach is that it is no longer necessary to use the damage interaction, or D-diagram, because the damage due to the combined effects of creep and fatigue are accounted in the test data by means of a specimen that is designed to replicate or bound the stress and strain redistribution that occurs in actual components when loaded in the creep regime. The reference approach to combining the two methodologies and the corresponding uncertainties and validation plans are presented. Results from recent key feature tests are discussed to illustrate the applicability of the EPP methodology and the behavior of materials at elevated temperature when undergoing stress and strain redistribution due to plasticity and creep.

42 ENGINEERING↗

Detection of ratcheting in finite element calculations

The distinction between a ratcheting and non-ratcheting response is critical for many high temperature design methods. Non-ratcheting is generally considered safe deformation remain bounded over the lifetime of the component while ratcheting is undesirable. As a particular example, the elastic perfectly plastic (EPP) design methods described in recent ASME Section III, Division 5 code cases require a designer to distinguish ratcheting from non-ratcheting for finite element analyses using a relatively simple, elastic perfectly-plastic constitutive response. However, it can be quite difficult to distinguish these two deformation regimes using finite element (FE) analysis particularly in the case where the actual ratcheting strain is small. In practice FE analysis of structures that are analytically in either the plastic shakedown or ratcheting regimes will result in small, cycle to -cycle accumulated strains characteristic of ratcheting. Distinguishing false ratcheting the structure is actually in the plastic shakedown regime from true ratcheting can be challenging. We describe the characteristics of nonlinear FE analysis that cause these false ratcheting strains and describe practical methods for distinguishing a ratcheting from a non-ratcheting response.

Messner, M. C.↗

The role of material modeling on strain range estimation for elevated temperature cyclic life evaluation

High temperature nuclear reactors operating in the creep regime are designed to withstand numerous cyclic events. Current ASME code rules provide two basic paths for evaluating creep fatigue and ratcheting under these conditions; one based on full inelastic analysis intended to provide a representative stress and strain history and the other based on elastic material models with adjustments of varying complexity to account for inelastic stress and strain redistribution. More recent developments have used elastic-perfectly plastic analysis to bound the effects of cyclic service. However, these methods still rely on the separate evaluation of fatigue and creep damage utilizing a damage interaction diagram. There is a procedure under current development that uses creep-fatigue data from key feature test articles directly without the use of the damage interaction diagram. However, it requires a reasonable representation of the strain range in a structure as an input. This work develops a simplified procedure based on elastic perfectly-plasticity analysis that can be used to represent the strain range in a structure in the steady state under cyclic loading conditions.

Messner, M. C.↗

THE ROLE OF MATERIAL MODELING ON STRAIN RANGE ESTIMATION FOR ELEVATED TEMPERATURE CYCLIC LIFE EVALUATION

High temperature nuclear reactors operating in the creep regime are designed to withstand numerous cyclic events. Current ASME code rules provide two basic paths for evaluating creep fatigue and ratcheting under these conditions; one based on full inelastic analysis intended to provide a representative stress and strain history and the other based on elastic material models with adjustments of varying complexity to account for inelastic stress and strain redistribution. More recent developments have used elastic-perfectly plastic analysis to bound the effects of cyclic service. However, these methods still rely on the separate evaluation of fatigue and creep damage utilizing a damage interaction diagram. There is a procedure under current development that uses creep-fatigue data from key feature test articles directly without the use of the damage interaction diagram. However, it requires a reasonable representation of the strain range in a structure as an input. This work develops a simplified procedure based on elastic perfectly-plasticity analysis that can be used to represent the strain range in a structure in the steady state under cyclic loading conditions.

Messner, Mark C.↗