Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electric Vehicles at Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Experimental Characterization of an Electric Ducted Fan for the SUSAN 25% Scale Research Vehicle

An electric ducted fan (EDF) was tested in the NASA Langley 12-Foot Low-Speed Tunnel for the SUbsonic Single Aft eNgine (SUSAN) Electrofan 25% scale research vehicle, which incorporates distributed electric fans along the wings and serves as a scaled electrified transport aircraft testbed. The commercial-off-the-shelf EDF was selected as a propulsor that can meet the 25% scale vehicle geometry constraints, along with the performance requirements throughout the flight profile. The test included a series of one-factor-at-a-time (OFAT) and design of experiments (DOE) approaches that were implemented across a range of fan speed, voltage, freestream dynamic pressure, and incidence angle settings to characterize the performance of the EDF. Several test matrix designs and modeling approaches were considered. System identification methods were used to develop a static motor model, a dynamic motor model, an EDF thrust model, and a power consumption model. The model predictive capabilities were then evaluated with validation data not used in the modeling process. The results provide a comprehensive set of models developed to characterize the fan, and offer general insight into EDF modeling approaches.

electric ducted fan↗
NASA NTRS1987

Variable-Reluctance Motor For Electric Vehicles

Report describes research on variable-reluctance electric-motor drive for eventual use in electric-vehicle propulsion. Primary design and performance criteria were torque and power output per unit mass of motor, cost, and drive efficiency. For each criterion, optimized drive design developed, and designs unified to yield single electric-vehicle drive. Scaled-down motor performed as expected. Prototype of paraplegic lift operated by toggle switch and joystick. Lift plugs into household electrical outlet for recharging when not in use.

Lang, Jeffrey H.↗
NASA NTRS1978

Test-vehicle cycle programmer

Instrument reduces manpower needed for testing electric powered vehicles. Device has dual scale that allows operator to compare actual speed with preprogrammed test speed. Features include large meter, buzzer, packaging to allow ready interchange of memories with different profiles, small size, minimal current drain, and reverse supply voltage protection.

Lesco, D. J.↗
NASA NTRS1983

NASA/GE Energy Efficient Engine low pressure turbine scaled test vehicle performance report

The low pressure turbine for the NASA/General Electric Energy Efficient Engine is a highly loaded five-stage design featuring high outer wall slope, controlled vortex aerodynamics, low stage flow coefficient, and reduced clearances. An assessment of the performance of the LPT has been made based on a series of scaled air-turbine tests divided into two phases: Block 1 and Block 2. The transition duct and the first two stages of the turbine were evaluated during the Block 1 phase from March through August 1979. The full five-stage scale model, representing the final integrated core/low spool (ICLS) design and incorporating redesigns of stages 1 and 2 based on Block 1 data analysis, was tested as Block 2 in June through September 1981. Results from the scaled air-turbine tests, reviewed herein, indicate that the five-stage turbine designed for the ICLS application will attain an efficiency level of 91.5 percent at the Mach 0.8/10.67-km (35,000-ft), max-climb design point. This is relative to program goals of 91.1 percent for the ICLS and 91.7 percent for the flight propulsion system (FPS).

Bridgeman, M. J.↗
NASA NTRS1992

Mars transportation system synthesis

Performance and requirements synthesized to support the manned Mars mission of the Space Exploration Initiative (SEI) are presented. Emphasis is placed on the Mars transportation system (MTS), which uses nuclear thermal rocket (NTR) propulsion technology associated with accomplishing the manned Mars mission. Data are also presented for a propulsion system options comparison of chemical/aerobrake and nuclear electric propulsion systems. Vehicle- and weight-scaling are used to determine the MTS mass, size, and performance range required for different Mars mission durations. The split sprint, opposition, and conjunction class mission modes are employed to determine the MTS requirements envelope. MTS sensitivity to Mars surface payload, crew size, Mars orbit payload, NTR engine thrust level, engine specific impulse, and NTR engine thrust-to-weight ratio are synthesized. A suggested NTR technology level to accomplish both cargo and piloted Mars missions is discussed.

Young, Archie C.↗
NASA NTRSDate not supplied

Simulation of Lift plus Cruise Vehicle Models to Define a Full-Scale Crash Test Campaign

A series of dynamic simulations were completed on the National Aeronautics and Space Administration(NASA) Lift plus Cruise (LPC) concept electric Vertical Take-off and Landing (eVTOL) vehicle in preparation for an anticipated future full-scale crash-test campaign. The crash test campaign is envisioned as a data gathering exercise with an intent generating full-scale test data to inform eVTOL crashworthiness regulations, evaluate the use of energy absorbing concepts within vehicle design, and validate finite element modeling techniques used in crashworthiness predictions. This report discusses the two main objectives for the simulation efforts: the development of a structural cabin section, and a series of analyses utilized to determine the sensitivities of impact variables. A structural cabin section was created based from previous research efforts involving the LPC vehicle utilized for occupant response. To refine for the structural modifications, the wing and tail sections of the vehicle were removed. The tail was replaced with a representative mass at the aft of the fuselage. The overhead wing was replaced with a beam structure sized to approximate the bending response of the wing under crash loading conditions. The beam structure was fixed to the fuselage similar to the original Wingbox design in order to properly capture effects of this overhead mass on survivable volume within the vehicle. The fidelity of the fuselage frame structure within the FEM was increased to quantify the effect of frame sizing on structural response. From this an eVTOL test article design was developed, which satisfied basic crashworthiness requirements, was reconfigurable to assess the effect of various design avenues on structural response and optimized to improve manufacturability. The impact variable sensitivity results primarily show the orientation of the impact vector played a major role in types of injuries sustained, along with their severity. The vehicle was largely insensitive to small variations in pitch attitude but highly sensitive to both impact surface at certain angles and landing gear location.

eVTOL↗
NASA NTRS2015

Aircraft Electric Propulsion Systems Applied Research at NASA

Researchers at NASA are investigating the potential for electric propulsion systems to revolutionize the design of aircraft from the small-scale general aviation sector to commuter and transport-class vehicles. Electric propulsion provides new degrees of design freedom that may enable opportunities for tightly coupled design and optimization of the propulsion system with the aircraft structure and control systems. This could lead to extraordinary reductions in ownership and operating costs, greenhouse gas emissions, and noise annoyance levels. We are building testbeds, high-fidelity aircraft simulations, and the first highly distributed electric inhabited flight test vehicle to begin to explore these opportunities.

Clarke, Sean↗
NASA NTRS2015

Aircraft Electric Propulsion Systems Applied Research at NASA

Researchers at NASA are investigating the potential for electric propulsion systems to revolutionize the design of aircraft from the small-scale general aviation sector to commuter and transport-class vehicles. Electric propulsion provides new degrees of design freedom that may enable opportunities for tightly coupled design and optimization of the propulsion system with the aircraft structure and control systems. This could lead to extraordinary reductions in ownership and operating costs, greenhouse gas emissions, and noise annoyance levels. We are building testbeds, high-fidelity aircraft simulations, and the first highly distributed electric inhabited flight test vehicle to begin to explore these opportunities.

Clarke, Sean↗
NASA NTRS1993

Ovonic nickel metal hydride batteries for space applications

Ovonic nickel-metal hydride (NiMH) rechargeable batteries are easily adaptable to a variety of applications. Small consumer NiMH cells were developed and are now being manufactured by licensees throughout the world. This technology was successfully scaled up in larger prismatic cells aimed at electric vehicle applications. Sealed cells aimed at satellite power applications were also built and cycle tested by OBC and other outside agencies. Prototype batteries with high specific energy (over 80 Wh/kg), high energy density (245 Wh/L), and excellent power capability (400 W/kg) were produced. Ovonic NiMH batteries demonstrated an excellent cycle life of over 10,000 cycles at 30 percent DOD. Presently, Ovonic Battery Company is working on an advanced version of this battery for space applications as part of an SBIR contract from NASA.

Venkatesan, S.↗
NASA NTRS1975

The high current transient generator, theory and operation for simulating lightning induced voltages into aerospace electrical circuits

Because of the difficulty, hazard, and cost of simulating full-scale lightning currents on flight vehicles, a nondestructive test technique using reduced-scale lightning currents was used to determine if threat level voltages will be induced into aircraft electrical circuits in the event the aircraft is actually struck by lightning. The reasoning and theory of selecting a particular simulated lightning waveshape and magnitude is given, showing that extrapolation of induced waveforms over several orders of magnitude should be avoided. The operation of high-current transient generators and hardware are described along with typical applications. The means by which voltages were generated, induced, and measured, as well as possible sources of error, are discussed.

Schulte, E. H.↗
NASA NTRS1979

Aerodynamic resistance reduction of electric and hybrid vehicles

The generation of an EHV aerodynamic data base was initiated by conducting full-scale wind tunnel tests on 16 vehicles. Zero-yaw drag coefficients ranged from a high of 0.58 for a boxey delivery van and an open roadster to a low of about 0.34 for a current 4-passenger prototype automobile which was designed with aerodynamics as an integrated parameter. Characteristic effects of aspect ratio or fineness ratio which might appear if electric vehicle shape proportions were to vary significantly from current automobiles were identified. Some preliminary results indicate a 5 to 10% variation in drag over the range of interest. Effective drag coefficient wind-weighting factors over J227a driving cycles in the presence of annual mean wind fields were identified. Such coefficients, when properly weighted, were found to be from 5 to 65% greater than the zero-yaw drag coefficient in the cases presented. A vehicle aerodynamics bibliography of over 160 entries, in six general categories is included.

Source record↗
NASA NTRSDate not supplied

Experimental Study of Aero-Propulsive Interactions for Electric Ducted Fan Arrays in Multiple Positions on a Wing

The Adaptable Distributed Electric Propulsion Testbed (ADEPT) Wing was tested in the NASA Langley 12-Foot Low-Speed Tunnel for the SUbsonic Single Aft eNgine (SUSAN) Electrofan 25% scale flight research vehicle, which aims to reduce emissions for commercial transport aircraft with electric propulsion technologies. The purpose of the test was to study the aero-propulsive effects across angle of attack and fan speed variations for several propulsor placements and array sizes, and to investigate how DEP can be leveraged for augmented lift and vehicle control. Six electric ducted fan (EDF) array placements were tested by positioning the fans along the leading and trailing edges on the top and bottom surfaces, as well as centered on the chord line in front of and behind the wing. Each fan placement configuration was tested with an array of one, three, and five EDFs to characterize an aero-propulsive extrapolation effect, and the bare wing was tested separately to provide baseline aerodynamic measurements. The results compare the longitudinal forces and moments for each configuration by analyzing the combined aero-propulsive interaction effects, and offer valuable insight into considerations for fan placement along a wing to enable the benefits of DEP integration.

Rose Weinstein↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the QUEEN V2 Test

A liquid-cooled electric ducted fan system was designed, built, and tested at the NASA Glenn Research Center. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, and a custom-designed heat exchanger integrated into the fan duct. Fan speed, thrust, and cooling system thermal performance was measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V2.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for regional single-aisle aircraft. This test demonstrated the functionality of the QUEEN V2, quantified the thrust produced by the electrofan, and characterized the electrical and thermal performance of the system. Lessons learned will be used to guide development of future QUEEN prototypes.

Aerodynamics↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the QUEEN V2 Test

A liquid-cooled electric ducted fan system was designed, built, and tested at the NASA Glenn Research Center. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, and a custom-designed heat exchanger integrated into the fan duct. Fan speed, thrust, and cooling system thermal performance was measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V2.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for regional single-aisle aircraft. This test demonstrated the functionality of the QUEEN V2, quantified the thrust produced by the electrofan, and characterized the electrical and thermal performance of the system. Lessons learned will be used to guide development of future QUEEN prototypes.

Aeronautics-General↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, an Electronic Speed Controller, a custom-designed inlet bellmouth, and several experimental inlet duct acoustic liners. Fan speed, thrust, and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large regional single-aisle aircraft. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller measured during this test are presented in a separate report.

L Danielle Koch↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off-the-Shelf fan, shroud, motor, and Electronic Speed Controller, plus a custom-designed inlet bellmouth, and four experimental inlet duct acoustic liners. Fan speed and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large single-aisle aircraft. Results indicated that inlet duct acoustic liners reduced tone and broadband noise as compared to a hardwall inlet duct. Predicted performance of the honeycomb liner compared well with measurements from an array of far field microphones. Inlet acoustic liners are just one method for mitigating noise for electric ducted fans for aircraft propulsion systems. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller are presented in a separate report.

Aircraft propulsion and power↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the Acoustic Tests of the QUEEN V1

Noise produced by an electric ducted fan system was measured in tests at the NASA Glenn Research Center Acoustical Testing Laboratory. Main components of the system include a Commercial-Off-the-Shelf fan, shroud, motor, and Electronic Speed Controller, plus a custom-designed inlet bellmouth, and four experimental inlet duct acoustic liners. Fan speed and noise were measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V1.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for large single-aisle aircraft. Results indicated that inlet duct acoustic liners reduced tone and broadband noise as compared to a hardwall inlet duct. Predicted performance of the honeycomb liner compared well with measurements from an array of far field microphones. Inlet acoustic liners are just one method for mitigating noise for electric ducted fans for aircraft propulsion systems. Lessons learned will be used to guide development of future QUEEN prototypes. Results of a thermal test of the Electronic Speed Controller are presented in a separate report.

Aircraft propulsion and power↗