Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electrical impedance spectroscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Study on the High-Pressure Behavior of Goethite up to 32 GPa Using X-Ray Diffraction, Raman, and Electrical Impedance Spectroscopy

Goethite is a major iron-bearing sedimentary mineral on Earth. In this study, we conducted in situ high-pressure x-ray diffraction, Raman, and electrical impedance spectroscopy measurements of goethite using a diamond anvil cell (DAC) at room temperature and high pressures up to 32 GPa. We observed feature changes in both the Raman spectra and electrical resistance at about 5 and 11 GPa. However, the x-ray diffraction patterns show no structural phase transition in the entire pressure range of the study. The derived pressure-volume (P-V) data show a smooth compression curve with no clear evidence of any second-order phase transition. Fitting the volumetric data to the second-order Birch–Murnaghan equation of state yields V 0 = 138.9 ± 0.5 Å 3 and K 0 = 126 ± 5 GPa.

58 GEOSCIENCES↗
DOE OSTI2021

Quantifying Properties for a Mechanistic, Predictive Understanding of Aqueous Impact on Aging of Medium and Low Voltage AC and DC Cabling in Nuclear Power Plants

To address the gap in knowledge in understanding degradation in relevant service conditions, this project aimed to develop a mechanistic, predictive model of medium and low voltage cable failure based on the primary environmental degradation parameters of aqueous immersion time, temperature, and the oxidation extent. To do so, we took a two-fold approach toward evaluating degradation as related to the aqueous condition. First, we evaluated the chemical, mechanical, and electrical properties of polymers that comprise the cabling insulation under varied aqueous conditions at different temperatures. Secondly, we evaluated the performance of insulation materials under similar accelerated aging conditions in addition to the dielectric breakdown of the cabling under submersion conditions. Thermal oxidation and immersion of LDPE thin films were done using a Parr vessel and the extent of oxidation was monitored using the carbonyl index from ATR-FTIR spectrum, a ratio quantifying the carbonyl functionality produced on the LDPE film surface. Increasing the temperature, oxidation time, and oxygen pressure increased the water-vapor permeability and the carbonyl content. Thermogravimetric analysis of the films confirmed that there is indeed an initial weight loss of the smaller molecular weight molecules and volatiles. At higher temperatures, there is a secondary mass loss. Up to 70°C, the mass loss curves were similar until 80°C, when the aged films decreased at a much greater rate with respect to increasing temperature. This was seen in the 10, 50, 90% weight loss temperatures. The mechanical properties of sheet PP and HDPE as well as injection molded LDPE, HDPE, HDPP dog bones were plotted with respect to the time spent in the Parr vessel during thermal oxidation. For the sheet PP and HDPE, the UTS and the modulus of elasticity decreased while the elongation increased. The injection-molded LDPE, HDPE, and HDPP dog bones experienced a similar trend where the changes in the properties were within experimental uncertainty. This analysis of LDPE in dry and immersive oxygen-rich environments is an important baseline for future experiments looking at other degradation mechanisms. A predictive aging model for low-density polyethylene insulative cable housings was developed. This model revealed a combination of physical and chemical processes which lead to an increase in permeability and a decrease in strength of the insulator. In creating this predictive model, a gap of knowledge in the literature was revealed in two areas: understanding how the crystallinity of a polymer changes with time and visualizing the predicted pores formed through the insulator which leads to failure. Developing and using an adapted ATR-FTIR method, crystallinity was monitored and compared to bulk crystallinity found via DSC. Inhomogeneity in crystallinity changes were observed but the FTIR method but was found to be less reliable. Pore visualization was found utilizing electrical impedance spectroscopy saturated aged polyethylene films with synthesized citrate-capped gold nanoparticles, and chloroauric acid precursor. results indicate a decreasing impedance of the polyethylene films caused by the transport of ions through the film. SEM imaging was then performed for elemental analysis of the films and counter electrodes for the presence of ions. Chloride and gold ions were detected; however, no nanoparticles were found. This gives an estimated pore size of at least 0.3 nm through the aged film. Cyclic submergence of polyethylene and polypropylene in aqueous solutions of copper sulfate and Harrison’s solution were examined. It was discovered that aging in these mixed conditions and at 90°C did cause a small, yet significant increase to tensile strength for both unaged polyethylene and polypropylene. The PE and PP in cycled and submerged conditions did not have tensile strengths significantly different from dry-aged after 16 weeks. For both solutions, it was determined that capacitance increases with both water tree depth and cable temperature and is relatively independent of changing water tree AR. As for resistance, there is no apparent change between depth percentages of 10 and 80 for both solutions. This is because the water tree has not yet entered the conductor and thus there is no shorting current flowing through the tree yet. Between 80 and 100% water tree depth, it is observed that for both solutions there is a rapid decrease in resistance because the tree is now impacting the conductor shield and allowing shorting current to flow through it. The relationship between resistance and temperature was found to be inversed. As temperature increases, resistance decreases for both water tree solutions with distilled water having the most apparent difference across the range of temperatures simulated. With regards to water tree AR, resistance was found to be relatively independent at depth percentages of 10, 50, and 70, but there was some relationship at 100% depth for both solutions. At this depth, as water tree AR increased, resistance was found to also increase. Through the examination of voltage and electric field distribution plots, it was confirmed for EPR cables that increasing water tree depth leads to increasing distortion. The increase in shorting current at 100% depth for aqueous copper sulfate compared to distilled water was also visualized. Lastly, the relationship between shorting current and temperature for narrow water trees was visualized and validated using the distribution plots. This study has led to a better understanding of the effect of cable temperature, water tree solution, and geometry of the tree region on cable degradation. Furthermore, this study has documented simulation results of water tree degradation in EPR MV cables, which had been previously lacking in information. Future work in this area will add frequency into the mix and examine what effect it has on the rate of cable degradation as a result of water treeing. To compliment the work being carried by UMD on different polymer chemistries, harvested medium voltage (MV) cables were selected for accelerated aging study at ORNL. These medium voltage cables are representative of the vintages and materials that are currently in use at existing nuclear power plants (NPPs). These cables were immersed in water at 90°C and energized for a period of two years at elevated voltage. Partial discharge was measured during this period of time to track potential degradation. Unfortunately, due to the absence of failure, the extent of integration between the UMD techniques and the harvested MV insulation was limited. However, based on the findings and from the UMD research in the previous sections on polyethylene and polypropylene, follow-on characterization for harvested MV cable insulation should focus on sample preparation to take advantage of the UMD techniques to better understand mechanistic degradation in MV cable insulations. This would include: 1.) Utilization of solutions and impedance measurement insulation to track permeability in harvested and accelerated aging insulation samples, 2.) Adaptation of gold nanoparticle synthesis for electrical impedance spectroscopy with supporting SEM characterization to study pore formation in harvested and accelerated aged insulation samples, & 3.) ATR-FTIR crystallinity with multiple temperature dependent harvested MV cable insulation under different air and submerged accelerated aging. In addition, low voltage dielectric spectroscopy and high voltage dissipation factor, tan δ, could be implemented as a condition monitoring tool for harvested MV cable insulation in submerged environments.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Microneedle-based electrical impedance sensor to monitor plant water status in real time

A sensor uses microneedle electrodes and multi-frequency electrical impedance spectroscopy to monitor plant water status in real time. The microneedle can be between 10 and 1000 microns in length, enabling precise placement in a variety of plant tissues. The impedance behavior can distinguish electrical properties and physiological functions of different plant tissue types. Therefore, impedance measurements can be used to monitor water stress to prevent irreversible damage to a plant and to enable improvement of plant biomass or fruit yield.

Hanson, David T.↗
DOE OSTI2022

Improved Understanding of Zircaloy Hydrogen Pickup Mechanisms in BWRs. NSUF Report (Final Report)

Using an instrumented autoclave operating at 288°C and 1100 psi, electrical impedance spectroscopy (EIS) measurements were taken from three neutron irradiated fuel channel samples (Zircaloy-2 and Zircaloy-4). The three high priority fuel channel samples were tested at 288°C using a simulated PWR water with the AC frequency range extending down through 10 -4 Hz, with corresponding DC measurements to validate the resistance measurements. EIS measurements were also taken at room temperature using a simulated PWR water from four neutron irradiated fuel channel samples (Zircaloy-2 and Zircaloy-4). and four water rod samples (Zircaloy-2). EIS measurements were also performed on unirradiated Zircaloy-2 tubes that were previously oxidized in autoclaves at various temperatures for different time durations to obtain oxide layers of different thicknesses. These experiments proved to be more challenging than anticipated because of the small size of the samples, which required development of fixtures to allow valid testing of the materials, some of which are radioactive, under pressure and temperature. Equivalent circuits were used to model the data. Some samples resulted in Nyquist plots where the arcs were too close to each other resulting in the inability to separate the different oxide morphological thicknesses. Microstructural characterization in the form of optical microscopy, scanning electron microscopy and (scanning) transmission electron microscopy was performed to document the microstructural features of the oxidized Zr-2 and Zr-4 samples (oxide and metal/oxide interface) and to interpret the EIS results. At the start of this work, it was assumed that despite the laminar cracks and porosity visible in both optical and SEM, the oxide scale is dense near the metal, effectively preventing the water from contacting the metal directly. While it is generally accepted that the large laminar cracks pores allow the water to percolate into the oxide film, it is unknown just how deep it can go, and how interconnected is the porosity, which will dictate how much the porosity is connected electrically to the water within the oxide scale. The EIS results demonstrated that there is in fact a distribution of oxide thicknesses over the various samples, and within each material condition, that are communicating to the liquid. This is derived from the fact that Nyquist plots have an arc radius whose center point is often below the Z’ axis, implying that instead of a single oxide thickness, these oxides have a distribution of thicknesses. This distribution of thicknesses produces arcs that are not clearly separable in most of the samples.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Percolated Ionic Aggregate Morphologies and Decoupled Ion Transport in Precise Sulfonated Polymers Synthesized by Ring-Opening Metathesis Polymerization

Here, we describe a set of precise single-ion conducting polymers that form self-assembled percolated ionic aggregates in glassy polymer matrices and have decoupled transport of metal cations. These precise single-ion conductors (SICs), synthesized by a scalable ring-opening metathesis polymerization, consist of a polyethylene backbone with a sulfonated phenyl group pendant on every fifth carbon and are fully neutralized by a counterion X + (Li + , Na + , or Cs + ). Experimental X-ray scattering measurements and fully atomistic molecular dynamics (MD) simulations are in good agreement. The MD simulations show that the ionic groups nanophase separate from the polymer backbone to form percolating ionic aggregates. Using graph theory, we find that within the Li + - and Na + -neutralized polymers the percolated aggregates exhibit planar and ribbon-like configurations at intermediate length scales, while the percolated aggregates within the Cs + -neutralized polymers are more isotropic. Electrical impedance spectroscopy measurements show that the ionic conductivities exhibit Arrhenius behavior, with conductivities of 10 –7 to 10 –6 S/cm at 180 °C. In the MD simulations, the cations move between sulfonate groups in the percolated aggregates, larger ions travel further, and overall cations travel further than the polymer backbones, indicating a decoupled ion-transport mechanism. Thus, the percolated ionic aggregates in these polymers can serve as pathways to facilitate decoupled ion motion through a glassy polymer matrix.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Approaches to investigate the role of chelation in the corrosivity of biomass-derived oils

The need to provide the U.S. market with a renewable liquid fuel energy source from a non-food feedstock stream has gained considerable traction due to benefits such as improved energy efficiency, reduced environmental impacts, and enhanced national security. Practical achievement of these goals via biomass and bio-waste utilization involves production of liquid intermediates containing corrosive, reactive species like carboxylic acids, ketones, aldehydes, and hydroxyaldehydes. Such mixtures challenge materials of containment, processing, and transport. It is widely recognized that the smaller organic acids, such as acetic and formic, are corrosive and can remove protective surface oxides on alloys used in bio-oil processing infrastructure, and ketones can swell sealing polymers. However, literature shows, and findings herein confirm, larger carboxylic acids and bidentate alcohols are present. This highlights the potential for synergistic, detrimental effects of constituents in bio-oil corrosion, including direct reactivity of small acids compounded with the possibility of mobilization of protective metal oxide layers via chelation by larger acids and oxygenates. The question of whether species beyond small acids can significantly contribute to corrosion requires analytical approaches previously not applied to bio-oil corrosion studies and certainly not previously applied corroboratively. As such, this work introduces a combination of optical, mass spectral, and electrochemical impedance spectroscopies with an incubation approach to study metal mobilization, to facilitate elucidating chelation's role in bio-oil corrosive pathways. To enable systematic study of these oxygenates' material compatibility individually and in combination, a model matrix of bio-oil constituents was also developed based on identification of key components of real bio-oils.

09 BIOMASS FUELS↗
DOE OSTI2024

Interfacial defect reduction enhances universal power law response in Mo–SiNx granular metals

Granular metals (GMs), consisting of metal nanoparticles separated by an insulating matrix, frequently serve as a platform for fundamental electron transport studies. However, few technologically mature devices incorporating GMs have been realized, in large part because intrinsic defects (e.g., electron trapping sites and metal/insulator interfacial defects) frequently impede electron transport, particularly in GMs that do not contain noble metals. Here, we demonstrate that such defects can be minimized in molybdenum–silicon nitride (Mo–SiN x ) GMs via optimization of the sputter deposition atmosphere. For Mo–SiN x GMs deposited in a mixed Ar/N 2 environment, x-ray photoemission spectroscopy shows a 40%–60% reduction of interfacial Mo-silicide defects compared to Mo–SiN x GMs sputtered in a pure Ar environment. Electron transport measurements confirm the reduced defect density; the dc conductivity improved (decreased) by 10 4 –10 5 and the activation energy for variable-range hopping increased 10×. Since GMs are disordered materials, the GM nanostructure should, theoretically, support a universal power law (UPL) response; in practice, that response is generally overwhelmed by resistive (defective) transport. Here, the defect-minimized Mo–SiN x GMs display a superlinear UPL response, which we quantify as the ratio of the conductivity at 1 MHz to that at dc, Δσ ω ⁠. Remarkably, these GMs display a Δσ ω up to 10 7 , a three-orders-of-magnitude improved response than previously reported for GMs. By enabling high-performance electric transport with a non-noble metal GM, this work represents an important step toward both new fundamental UPL research and scalable, mature GM device applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The role of alkali metal cations and platinum-surface hydroxyl in the alkaline hydrogen evolution reaction

The platinum-catalysed hydrogen evolution reaction (HER) generally shows poorer kinetics in alkaline electrolyte and represents a key challenge for alkaline water electrolysis. In the presence of alkali metal cations and hydroxyl anions, the electrode–electrolyte (platinum–water) interface in an alkaline electrolyte is far more complex than that in an acidic electrolyte. Here we combine electrochemical impedance spectroscopy and an electrical transport spectroscopy approach to probe and understand the fundamental role of different cations (Li + , Na + and K + ) in HER kinetics. Our integrated studies suggest that the alkali metal cations play an indirect role in modifying the HER kinetics, with the smaller cations being less destabilizing to the hydroxyl adsorbate (OH ad ) species in the HER potential window, which favours a higher coverage of OH ad on the platinum surface. Here, the surface OH ad species are highly polar and act as both electronically favoured proton acceptors and geometrically favoured proton donors to promote water dissociation in alkaline media, thus boosting the Volmer-step kinetics and the HER activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Broad Applicability of Electrochemical Impedance Spectroscopy to the Measurement of Oxygen Nonstoichiometry in Mixed Ion and Electron Conductors

Oxygen non-stoichiometry is a fundamental feature of mixed ion and electron conductors (MIECs). In this work a general electrochemical method for determining non-stoichiometry in thin film MIECs, via measurement of the chemical capacitance, is demonstrated using ceria and ceria-zirconia (Ce 0.8 Zr 0.2 O 2-δ ) as representative materials. A.C. impedance data are collected from both materials at high temperature (750-900 °C) under reducing conditions with oxygen partial pressure (pO 2 ) in the range 10-13 to 10-20 atm. Additional measurements of ceria-zirconia films are made under relatively oxidizing conditions with pO 2 in the range 0.2 to 10 -4 atm and temperatures of 800-900 °C. Under reducing conditions, the impedance spectra are described by a simple circuit in which a resistor is in series with a resistor and capacitor in parallel, and thickness dependent measurements are used to resolve the capacitance into interfacial and chemical terms. Under more oxidizing conditions, the impedance spectra (of Ce 0.8 Zr 0.2 O 2-δ ) reveal an additional diffusional feature, which enables determination of the ionic resistance of the film in addition to the capacitance, and hence the transport properties. A generalized mathematical formalism is presented for recovering the non-stoichiometry from the chemical capacitance, without recourse to defect chemical models. The ceria non-stoichiometry values are in good agreement with literature values determined by thermogravimetric measurements but display considerably less scatter and are collected on considerably shorter timescales. Here, the thermodynamic analysis of Ce 0.8 Zr 0.2 O 2-δ corroborates earlier findings that introduction of Zr into ceria enhances its reducibility.

08 HYDROGEN↗
DOE OSTI2026

Task Sharing of Proton Incorporation in Vertically Aligned Nanocomposite Triple Conductors: Growth, Structure, and Surface Exchange Kinetics

As protonic ceramic electrolysis cells emerge for efficient H 2 production, there is a need to develop air electrode materials enabling fast, durable steam splitting and proton incorporation. Single-phase triple conductors may fail to satisfy the myriad performance/stability requirements, and their critical charge-carriers (holes, oxygen vacancies, and protons) are in competition, limiting their concentrations. Instead, we propose task-sharing, vertically aligned nanocomposites (VANs), comprising a proton conductor (BaZr 0.9 Y 0.1 O 3-δ ) and a redox-active mixed ionic electronic conductor (Ce 0.9 Pr 0.1 O 2-δ ), that may enable rapid proton surface exchange at the solid–gas interface and transport along the solid–solid heterointerfaces. We grew VANs by pulsed laser deposition and investigated the interplay between their processing conditions, structure, and proton and oxygen surface exchange kinetics. We varied the substrate temperature, laser repetition rate, laser fluence, and processing oxygen pressure. The crystallinity and phases were characterized by grazing-incidence X-ray diffraction, and the strain and structural order as a function of depth were evaluated by angle-dependent synchrotron X-ray pair distribution function analysis. To evaluate the potential for interdiffusion, the formation energies of substitutional defects were simulated with density functional theory. Corresponding structural analysis and elemental mapping were performed by scanning/transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electron energy-loss spectroscopy, indicating distinct nanoscale compositional regions with a hierarchical structure embedded in individual VANs columns and minimal interdiffusion across a bilayer film. Proton and oxygen surface exchange coefficients (k H , k O ) and polarization resistances were evaluated by electrical and optical relaxations and impedance spectroscopy of VAN-incorporated protonic ceramic electrochemical cells, respectively, at 400–500 °C, demonstrating values comparable to some of the best-known triple and mixed conductors.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Laboratory Electrical Conductivity of Marine Gas Hydrate

Methane hydrate was synthesized from pure water ice and flash frozen seawater, with varying amounts of sand or silt added. Electrical conductivity was determined by impedance spectroscopy, using equivalent circuit modeling to separate the effects of electrodes and to gain insight into conduction mechanisms. Silt and sand increase the conductivity of pure hydrate; we infer by contaminant NaCl contributing to conduction in hydrate, to values in agreement with resistivities observed in well logs through hydrate–saturated sediment. The addition of silt and sand lowers the conductivity of hydrate synthesized from seawater by an amount consistent with Archie's law. Here, all samples were characterized using cryogenic scanning electron microscopy and energy dispersive spectroscopy, which show good connectivity of salt and brine phases. Electrical conductivity measurements of pure hydrate and hydrate mixed with silt during pressure–induced dissociation support previous conclusions that sediment increases dissociation rate.

58 GEOSCIENCES↗
DOE OSTI2020

Characterizing Baselines and Change in Gas Hydrate Systems using EM Methods

The objective of this project was to advance our understanding of gas hydrate systems in nature by characterizing their electrical properties in the field and in the laboratory. In the laboratory measurements, methane hydrate was synthesized from pure water ice and flash frozen seawater, with varying amounts of sand or silt added. Electrical conductivity was determined by impedance spectroscopy, using equivalent circuit modeling to separate the effects of electrodes and to gain insight into conduction mechanisms. Silt and sand increase the conductivity of pure hydrate, inferred to be contaminant NaCl contributing to conduction in hydrate, to a peak conductivity in agreement with peak resistivities observed in well logs through massive hydrate (3,000--10,000 Ωm). The addition of silt and sand lowers the conductivity of hydrate synthesized from seawater, by an amount consistent with Archie's Law. All samples were characterized using cryogenic scanning electron microscopy and energy dispersive spectroscopy, which shows good connectivity of salt and brine phases. Electrical conductivity measurements of pure hydrate and hydrate mixed with silt during pressure-induced dissociation supports previous conclusions that sediment increases dissociation rate. In order to characterize gas hydrate systems in the field, we collected 360 line kilometers of controlled-source electromagnetic data on Walker Ridge 313, Orca Basin (WR100), Mad Dog (GC781), and Green Canyon 955 in the Gulf of Mexico, all areas with known or seismically inferred gas hydrate deposits and which have be drilled or targeted for future drilling. We deep-towed an EM transmitter that generates an alternating electric field which propagates through the seafloor geology. Data were recorded on 6 receivers towed behind the transmitter at distances between 550 and 1550 m. In the presence of conductive geology, the electric fields will be attenuated, and conversely, in resistive geology the fields will be preserved. Our data were inverted using a 2D inversion method that first optimizes the model-data misfit, then finds the smoothest model fitting the data. This ensures that resistivity structures present in the final model are likely necessary. At each of the proposed drilling sites we found increased resistivity, interpreted as increased hydrate concentrations. However, not only were the primary drilling sites not always more resistive than the alternate sites, at WR313 the strongest resistors were not at the locations targeted for drilling.

03 NATURAL GAS↗
DOE OSTI2022

Electrically controlling and optically observing the membrane potential of supported lipid bilayers

Supported lipid bilayers are a well-developed model system for the study of membranes and their associated proteins, such as membrane channels, enzymes, and receptors. These versatile model membranes can be made from various components, ranging from simple synthetic phospholipids to complex mixtures of constituents, mimicking the cell membrane with its relevant physiochemical and molecular phenomena. In addition, the high stability of supported lipid bilayers allows for their study via a wide array of experimental probes. In this work, we describe a platform for supported lipid bilayers that is accessible both electrically and optically, and demonstrate direct optical observation of the transmembrane potential of supported lipid bilayers. We show that the polarization of the supported membrane can be electrically controlled and optically probed using voltage-sensitive dyes. Membrane polarization dynamics is understood through electrochemical impedance spectroscopy and the analysis of an equivalent electrical circuit model. In addition, we describe the effect of the conducting electrode layer on the fluorescence of the optical probe through metal-induced energy transfer, and show that while this energy transfer has an adverse effect on the voltage sensitivity of the fluorescent probe, its strong distance dependency allows for axial localization of fluorescent emitters with ultrahigh accuracy. We conclude with a discussion on possible applications of this platform for the study of voltage-dependent membrane proteins and other processes in membrane biology and surface science.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Moderate temperature sintering of BaZr 0.8 Y 0.2 O 3-δ protonic ceramics by A novel cold sintering pretreatment

The state-of-the-art protonic ceramic conductor BaZr 0.8 Y 0.2 O 3-δ (BZY20) requires an extremely high sintering temperature (≥1700 °C) to achieve the desired relative density and microstructure necessary to function as a proton conducting electrolyte. In this work, we developed a cold sintering pretreatment assisted moderate-temperature sintering method for the fabrication of high-quality pure BZY20 pellets. BZY20 pellets with high relative density of ~94% were fabricated with a final sintering temperature of 1500 °C (200 °C lower than the traditional sintering temperature). A comparison with BZY20 control samples indicated that the proper amount of BaCO 3 introduced on the BZY20 particle surface and the high green density achieved by cold sintering pretreatment were the main drivers for lowering the sintering temperature. The electrical conductivity measurement by electrochemical impedance spectroscopy showed that the as-prepared BZY20 pellets have a proton conductivity comparable to the state-of-the-art values. The cold sintering pretreatment outlined in this work has the potential to lower the sintering temperatures for similar types of protonic ceramic materials under consideration for a wide range of energy conversion and storage applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of SiO x anode fading mechanism with limited capacity cycling

Silicon suboxide (SiO x ) is one of the promising anode materials for the next-generation lithium-ion batteries. However, SiO x has a severe capacity fading problem during cycling. It is thus desired to investigate the detailed fading mechanisms of SiO x anode materials. In this study, limited capacity cycling was employed to examine the electrochemical behaviors of the SiO x anode, and the lithiation/delithiation cycling was limited within a range of 10% theoretical capacity. This strategy minimizes the volume variation of SiO x materials upon charging/discharging, which helps to reveal their decay factors other than volume fluctuation. It is demonstrated that the instability of the SiO x surface during cycling was likely a parallel factor of active material fading, which seems to cause unfavored electrode interface rearrangements with lowered electric conductivity.

electric vehicles↗
DOE OSTI2022

Constant-potential molecular dynamics simulations of molten salt double layers for FLiBe and FLiNaK

We report the results of constant-potential molecular dynamics simulations of the double layer interface between molten 2LiF–BeF 2 (FLiBe) and 23LiF–6NaF–21KF (FLiNaK) fluoride mixtures and idealized solid electrodes. Employing methods similar to those used in studies of chloride double layers, we compute the structure and differential capacitance of molten fluoride electric double layers as a function of applied voltage. The role of molten salt structure is probed through comparisons between FLiBe and FLiNaK, which serve as models for strong and weak associate-forming salts, respectively. In FLiBe, screening involves changes in Be–F–Be angles and alignment of the oligomers parallel to the electrode, while in FLiNaK, the electric field is screened mainly by rearrangement of individual ions, predominantly the polarizable potassium cation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Insight into the Fast-Rechargeability of a Novel Mo 1.5 W 1.5 Nb 14 O 44 Anode Material for High-Performance Lithium-Ion Batteries

Wadsley–Roth phased niobates are promising anode materials for lithium-ion batteries, while their inherently low electrical conductivity still limits their rate-capability. Herein, a novel doped Mo 1.5 W 1.5 Nb 14 O 44 (MWNO) material is facilely prepared via an ionothermal-synthesis-assisted doping strategy. The detailed crystal structure of MWNO is characterized by neutron powder diffraction and aberration corrected scanning transmission electron microscope, unveiling the full occupation of Mo 6+ -dopant at the t1 tetrahedral site. In half-cells, MWNO exhibits enhanced fast-rechargeability. In this work, the origin of the improved performance is investigated by ultraviolet–visible diffuse reflectance spectroscopy, density functional theory (DFT) computation, and electrochemical impedance spectroscopy, revealing that bandgap narrowing improves the electrical conductivity of MWNO. Furthermore, operando X-ray diffraction elucidates that MWNO exhibits a typical solid-solution phase conversion-based lithium-ion insertion/extraction mechanism with reversible structural evolution during the electrochemical reaction. The boosted lithium-ion diffusivity of MWNO, due to the Mo 6+ /W 6+ doping effect, is confirmed by a galvanostatic intermittent titration technique and DFT. With the simultaneously enhanced electrical conductivity and lithium-ion diffusivity, MWNO successfully demonstrates its fast-rechargeability and practicality in the LiNi 0.5 Mn 1.5 O 4 -coupled full-cells. Therefore, this work illustrates the potential of ionothermal synthesis in energy storage materials and provides a mechanistic understanding of the doping effect on improving material's electrochemical performance.

25 ENERGY STORAGE↗