Search NASA⌕ Search

SEARCH · Search NASA

Results for “Embedded Devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Analyzing Risks and Vulnerabilities of Various Computer Systems and Undergoing Exploitation using Embedded Devices

Security is one of the most if not the most important areas today. After the several attacks on the United States, security everywhere has heightened from airports to communication among the military branches legionnaires. With advanced persistent threats (APTs) on the rise following Stuxnet, government branches and agencies are required, more than ever, to follow several standards, policies and procedures to reduce the likelihood of a breach. Attack vectors today are very advanced and are going to continue to get more and more advanced as security controls advance. This creates a need for networks and systems to be in an updated, patched and secured state in a launch control system environment. Attacks on critical systems are becoming more and more relevant and frequent. Nation states are hacking into critical networks that might control electrical power grids or water dams as well as carrying out advanced persistent threat (APTs) attacks on government entities. NASA, as an organization, must protect its self from attacks from all different types of attackers with different motives. Although the International Space Station was created, there is still competition between the different space programs. With that in mind, NASA might get attacked and breached for various reasons such as espionage or sabotage. My project will provide a way for NASA to complete an in house penetration test which includes: asset discovery, vulnerability scans, exploit vulnerabilities and also provide forensic information to harden systems. Completing penetration testing is a part of the compliance requirements of the Federal Information Security Act (FISMA) and NASA NPR 2810.1 and related NASA Handbooks. This project is to demonstrate how in house penetration testing can be conducted that will satisfy all of the compliance requirements of the National Institute of Standards and Technology (NIST), as outlined in FISMA. By the end of this project, I hope to have carried out the tasks stated above as well as gain an immense knowledge about compliance, security tools, networks and network devices, as well as policies and procedures.

Penetration Testing↗
NASA NTRS2009

Proof Compression and the Mobius PCC Architecture for Embedded Devices

The EU Mobius project has been concerned with the security of Java applications, and of mobile devices such as smart phones that execute such applications. In this talk, I'll give a brief overview of the results obtained on on-device checking of various security-related program properties. I'll then describe in more detail how the concept of certified abstract interpretation and abstraction-carrying code can be applied to polyhedral-based analysis of Java byte code in order to verify properties pertaining to the usage of resources of a down-loaded application. Particular emphasis has been on finding ways of reducing the size of the certificates that accompany a piece of code.

Jensen, Thomas↗
NASA NTRS2003

Development of reliable electronic packaging solutions for spacecraft avionics miniaturization using embedded passice devices

Miniaturization of electronic packages will play a key rule in future space avionics systems. Smaller avionics packages will reduce payloads while providing greater functionality for information processing and mission instrumentation. Current surface mount technology discrete passive devices not only take up significant space but also add weight. To that end, the use of embedded passive devices, such as capacitors, inductors and resistors will be instrumental in allowing electronics to be made smaller and lighter. Embedded passive devices fabricated on silicon or like substrates using thin film technology, promise great savings in circuit volume, as well as potentially improving electrical performance by decreasing parasitic losses. These devices exhibit a low physical profile and allow the circuit footprint to be reduced by stacking passive elements within a substrate. Thin film technologies used to deposit embedded passive devices are improving and costs associated with the process are decreasing.

Schatzel, Don↗
NASA NTRS2002

Flow-Field Measurement of Device-Induced Embedded Streamwise Vortex on a Flat Plate

Detailed flow-field measurements were performed downstream of a single vortex generator (VG) using an advanced Stereo Digital Particle Image Velocimetry system. Thc passive flow-control devices examined consisted of a low-profile VG with a device height, h, approximately equal to 20 percent of the boundary-layer thickness, sigma, and a conventional VG with h is approximately sigma. Flow-field data were taken at twelve cross-flow planes downstream of the VG to document and quantify the evolution of embedded streamwise vortex. The effects of device angle of attack on vortex development downstream were compared between the low-profile VG and the conventional VG. Key parameters including vorticity, circulation, trajectory, and half-life radius - describing concentration, strength, path, and size, respectively--of the device-induced streamwise vortex were extracted from the flow-field data. The magnitude of maximum vorticity increases as angle of attack increases for the low-profile VG, but the trend is reversed for the conventional VG, probably due to flow stalling around the larger device at higher angles of attack. Peak vorticity and circulation for the low-profile VG decays exponentially and inversely proportional to the distance downstream from the device. The device-height normalized vortex trajectories for the low-profile VG, especially in the lateral direction, follow the general trends of the conventional VG. The experimental database was used to validate the predictive capability of computational fluid dynamics (CFD). CFD accurately predicts the vortex circulation and path; however, improvements are needed for predicting the vorticity strength and vortex size.

Yao, Chung-Sheng↗
NASA NTRS2005

LC Circuits for Diagnosing Embedded Piezoelectric Devices

A recently invented method of nonintrusively detecting faults in piezoelectric devices involves measurement of the resonance frequencies of inductor capacitor (LC) resonant circuits. The method is intended especially to enable diagnosis of piezoelectric sensors, actuators, and sensor/actuators that are embedded in structures and/or are components of multilayer composite material structures.

Chattin, Richard L.↗
NASA NTRS1991

Intelligent structures technology

Viewgraphs on intelligent structures technology are presented. Topics covered include: embedding electronics; electrical and mechanical compatibility; integrated circuit chip packaged for embedding; embedding devices within composite structures; test of embedded circuit in G/E coupon; temperature/humidity/bias test; single-chip microcomputer control experiment; and structural shape determination.

Crawley, Edward F.↗
NASA NTRS2005

Data management in the mission data system

As spacecraft evolve from simple embedded devices to become more sophisticated computing platforms with complex behaviors it is increasingly necessary to model and manage the flow of data, and to provide uniform models for managing data that promote adaptability, yet pay heed to the physical limitations of the embedded and space environments.

mission data system (MDS)↗
NASA NTRS2006

Acceleration of Stereo Correlation in Verilog

To speed up vision processing in low speed, low power devices, embedding FPGA hardware is becoming an effective way to add processing capability. FPGAs offer the ability to flexibly add parallel and/or deeply pipelined computation to embedded processors without adding significantly to the mass and power requirements of an embedded system. This paper will discuss the JPL stereo vision system, and describe how a portion of that system was accelerated by using custom FPGA hardware to process the computationally intensive portions of JPL stereo. The architecture described takes full advantage of the ability of an FPGA to use many small computation elements in parallel. This resulted in a 16 times speedup in real hardware over using a simple linear processor to compute image correlation and disparity.

machine vision↗
NASA NTRS2009

A Distributed Prognostic Health Management Architecture

This paper introduces a generic distributed prognostic health management (PHM) architecture with specific application to the electrical power systems domain. Current state-of-the-art PHM systems are mostly centralized in nature, where all the processing is reliant on a single processor. This can lead to loss of functionality in case of a crash of the central processor or monitor. Furthermore, with increases in the volume of sensor data as well as the complexity of algorithms, traditional centralized systems become unsuitable for successful deployment, and efficient distributed architectures are required. A distributed architecture though, is not effective unless there is an algorithmic framework to take advantage of its unique abilities. The health management paradigm envisaged here incorporates a heterogeneous set of system components monitored by a varied suite of sensors and a particle filtering (PF) framework that has the power and the flexibility to adapt to the different diagnostic and prognostic needs. Both the diagnostic and prognostic tasks are formulated as a particle filtering problem in order to explicitly represent and manage uncertainties; however, typically the complexity of the prognostic routine is higher than the computational power of one computational element ( CE). Individual CEs run diagnostic routines until the system variable being monitored crosses beyond a nominal threshold, upon which it coordinates with other networked CEs to run the prognostic routine in a distributed fashion. Implementation results from a network of distributed embedded devices monitoring a prototypical aircraft electrical power system are presented, where the CEs are Sun Microsystems Small Programmable Object Technology (SPOT) devices.

Bhaskar, Saha↗
NASA NTRS2011

SNE Industrial Fieldbus Interface

Programmable logic controllers (PLCs) have very limited diagnostic and no prognostic capabilities, while current smart sensor designs do not have the capability to communicate over Fieldbus networks. The aim is to interface smart sensors with PLCs so that health and status information, such as failure mode identification and measurement tolerance, can be communicated via an industrial Fieldbus such as ControlNet. The SNE Industrial Fieldbus Interface (SIFI) is an embedded device that acts as a communication module in a networked smart sensor. The purpose is to enable a smart sensor to communicate health and status information to other devices, such as PLCs, via an industrial Fieldbus networking protocol. The SNE (Smart Network Element) is attached to a commercial off-the-shelf Any bus-S interface module through the SIFI. Numerous Anybus-S modules are available, each one designed to interface with a specific Fieldbus. Development of the SIFI focused on communications using the ControlNet protocol, but any of the Anybus-S modules can be used. The SIFI communicates with the Any-bus module via a data buffer and mailbox system on the Anybus module, and supplies power to the module. The Anybus module transmits and receives data on the Fieldbus using the proper protocol. The SIFI is intended to be connected to other existing SNE modules in order to monitor the health and status of a transducer. The SIFI can also monitor aspects of its own health using an onboard watchdog timer and voltage monitors. The SIFI also has the hardware to drive a touchscreen LCD (liquid crystal display) unit for manual configuration and status monitoring.

Lucena, Angel↗
NASA NTRS2006

Nano Sensors for Gas Detection in Space and Ground Support Applications

Personnel living in a space environment as well as technicians and engineers preparing spacecraft for launch can potentially be exposed to small amounts of hazardous gases. It is therefore important to be able to detect, identify and quantify the presence of a gas especially when its presence could lead to a fatal situation. The use of small and sensitive sensors can allow for the placement of these devices over a large area, thus allowing for a more precise and timely determination of a gas leak. ASRC Aerospace and its research partners are developing nano sensors for detection of various gases, including but not limited to: H2, NH3, N2O4, hydrazine and others. Initial laboratory testing has demonstrated the capability to detect the gases in concentrations lower than parts per million. Testing and development is continuing to improve the response and recovery times, to increase the sensitivity of the devices. Different coatings and electrodes are currently being evaluated to determine the optimum configuration of a variety of gases. The small footprint of the Nano sensors allows for several devices, each responsive in a different way to different gases, to be placed into a single substrate. Multiple devices embedded into a single substrate results in increased reliability and in a decrease for periodic calibrations. The use of different coatings will result in a small electronic nose capable of distinguishing between different gases. A multi-channel signal conditioner amplifier built on a small multi chip module is used to process the output of the sensors and to deliver a signal that can be remotely monitored. All the data is digitized and transmitted over the same cable pair used to power the amplifier. Multiple outputs can be connected to a single cable pair in order to minimize the added weight and expense associated with cabling in a spacecraft. The sensors will be run through a qualification process to evaluate their suitability for space applications we are expecting to have fully functional sensors available for initial field deployment and testing by the end of the year 2006.

Medelius, Pedro J.↗
NASA NTRS2013

Distributed Engine Control Empirical/Analytical Verification Tools

NASA's vision for an intelligent engine will be realized with the development of a truly distributed control system featuring highly reliable, modular, and dependable components capable of both surviving the harsh engine operating environment and decentralized functionality. A set of control system verification tools was developed and applied to a C-MAPSS40K engine model, and metrics were established to assess the stability and performance of these control systems on the same platform. A software tool was developed that allows designers to assemble easily a distributed control system in software and immediately assess the overall impacts of the system on the target (simulated) platform, allowing control system designers to converge rapidly on acceptable architectures with consideration to all required hardware elements. The software developed in this program will be installed on a distributed hardware-in-the-loop (DHIL) simulation tool to assist NASA and the Distributed Engine Control Working Group (DECWG) in integrating DCS (distributed engine control systems) components onto existing and next-generation engines.The distributed engine control simulator blockset for MATLAB/Simulink and hardware simulator provides the capability to simulate virtual subcomponents, as well as swap actual subcomponents for hardware-in-the-loop (HIL) analysis. Subcomponents can be the communication network, smart sensor or actuator nodes, or a centralized control system. The distributed engine control blockset for MATLAB/Simulink is a software development tool. The software includes an engine simulation, a communication network simulation, control algorithms, and analysis algorithms set up in a modular environment for rapid simulation of different network architectures; the hardware consists of an embedded device running parts of the CMAPSS engine simulator and controlled through Simulink. The distributed engine control simulation, evaluation, and analysis technology provides unique capabilities to study the effects of a given change to the control system in the context of the distributed paradigm. The simulation tool can support treatment of all components within the control system, both virtual and real; these include communication data network, smart sensor and actuator nodes, centralized control system (FADEC full authority digital engine control), and the aircraft engine itself. The DECsim tool can allow simulation-based prototyping of control laws, control architectures, and decentralization strategies before hardware is integrated into the system. With the configuration specified, the simulator allows a variety of key factors to be systematically assessed. Such factors include control system performance, reliability, weight, and bandwidth utilization.

DeCastro, Jonathan↗
NASA NTRSDate not supplied

Delay Tolerant, Radio Frequency Identification (RFID)-enabled Sensing

In this paper, we describe a method of providing guaranteed delivery of sensor data gathered at arbitrary times using an only intermittently available radio frequency identification (RFID) transport scheme. This technique provides a passive (e.g., non-powered) interface for a power-constrained embedded device to transport sensor data while overcoming the limitation of infrequent access to an RFID interrogator.

Raymond S. Wagner↗
NASA NTRS2018

Piezoelectric Charging and Wireless Communication

Modern medicine is undergoing a revolution in the application of new sensor capabilities for aiding in diagnosis of specific conditions and monitoring a variety of informative vital signs. In the past, many of the measurements were limited by what could be accomplished externally. A shift toward in-vivo monitoring for both diagnostic and therapeutic sensing and actuation [1] has created a need for low power electronics, high energy density batteries and methods to successfully power devices embedded in the body. For a review of the field and sensing capabilities see [2]. Recent studies suggest that charging with ultrasound is more efficient at longer transmission distance (> 10cm) than inductive charging [3]. In this manuscript, we discuss the modeling and experimentation that we have accomplished and demonstrate in ultrasonic charging of sensors having the form and fit of in-vivo sensors. The task goal has been to use piezoelectric transducers for wireless communication and powering of sensors internal to the human body with a goal to transmit power levels of 100 W a receiver with receiving area of 3x3 mm2 over a distance of 16 cm equivalent to human body interior. The results suggest that we can transmit power levels that exceed this baseline requirement.

Jackson, Shannon↗
NASA NTRS1995

Non-standard analysis and embedded software

One model for computing in the future is ubiquitous, embedded computational devices analogous to embedded electrical motors. Many of these computers will control physical objects and processes. Such hidden computerized environments introduce new safety and correctness concerns whose treatment go beyond present Formal Methods. In particular, one has to begin to speak about Real Space software in analogy with Real Time software. By this we mean, computerized systems which have to meet requirements expressed in the real geometry of space. How to translate such requirements into ordinary software specifications and how to carry out proofs is a major challenge. In this talk we propose a research program based on the use of no-standard analysis. Much detail remains to be carried out. The purpose of the talk is to inform the Formal Methods community that Non-Standard Analysis provides a possible avenue to attack which we believe will be fruitful.

Platek, Richard↗
NASA NTRS1987

A simple device for the preparation of embedded materials science specimens for ultramicrotomy

A simple hand-held grinding fixture is discussed which can produce microtome mounts of hard materials, oriented interfaces, and powders embedded in a 5/16-in plastic rod. The device has been used for the ultramicrotomy of meteorite samples, 10-50 micron interplanetary dust particles, and thin films on plastic. Results are presented for a layer lattice silicate from the Murchison carbonaceous chondrite, illustrating the resolution and structural detail that can be obtained with the method.

Blake, D. F.↗