Search NASA⌕ Search

SEARCH · Search NASA

Results for “Engineering - Power transmission and distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Embedded Acoustic Sensor Array for Engine Fan Noise Source Diagnostic Test: Feasibility of Noise Telemetry via Wireless Smart Sensors

Aircraft engines have evolved into a highly complex system to meet ever-increasing demands. The evolution of engine technologies has primarily been driven by fuel efficiency, reliability, as well as engine noise concerns. One of the sources of engine noise is pressure fluctuations that are induced on the stator vanes. These local pressure fluctuations, once produced, propagate and coalesce with the pressure waves originating elsewhere on the stator to form a spinning pressure pattern. Depending on the duct geometry, air flow, and frequency of fluctuations, these spinning pressure patterns are self-sustaining and result in noise which eventually radiate to the far-field from engine. To investigate the nature of vane pressure fluctuations and the resulting engine noise, unsteady pressure signatures from an array of embedded acoustic sensors are recorded as a part of vane noise source diagnostics. Output time signatures from these sensors are routed to a control and data processing station adding complexity to the system and cable loss to the measured signal. "Smart" wireless sensors have data processing capability at the sensor locations which further increases the potential of wireless sensors. Smart sensors can process measured data locally and transmit only the important information through wireless communication. The aim of this wireless noise telemetry task was to demonstrate a single acoustic sensor wireless link for unsteady pressure measurement, and thus, establish the feasibility of distributed smart sensors scheme for aircraft engine vane surface unsteady pressure data transmission and characterization.

Zaman, Afroz↗
NASA NTRS1997

Automotive Insulation

Under a Space Act Agreement between Boeing North America and BSR Products, Space Shuttle Thermal Protection System (TPS) materials are now used to insulate race cars. BSR has created special TPS blanket insulation kits for use on autos that take part in NASCAR events, and other race cars through its nationwide catalog distribution system. Temperatures inside a race car's cockpit can soar to a sweltering 140 to 160 degrees, with the extreme heat coming through the engine firewall, transmission tunnel, and floor. It is common for NASCAR drivers to endure blisters and burns due to the excessive heat. Tests on a car insulated with the TPS material showed a temperature drop of some 50 degrees in the driver's cockpit. BSR-TPS Products, Inc. now manufactures insulation kits for distribution to race car teams around the world.

Source record↗
NASA NTRS1991

Performance evaluation of Platform Data ManagementSystem under various degrees of protocol implementation

The Platform Data Management System (DMS) collects Housekeeping (H/K), Payload (P/L) Engineering, and Payload Science data from various subsystems and payloads on the platform for transmission to the ground through the downlink via TDRSS. The DMS also distributes command data received from the ground to various subsystems and payloads. In addition, DMS distributes timing and safemode data. The function of collection and distribution of various types of data is performed by the Command and Data Handling (C&DH) subsystem of DMS. The C&DH subsystem uses for this purpose a number of data buses namely, Housekeeping, Payload Engineering, Payload Science, and Time and Safemode buses. Out of these buses, the H/K, P/L Engineering, and P/L Science buses are planned to be implemented by using MIL-STD 1553 bus. Most of the period covered was spent in developing a queue theoretic model of the 1553 Bus as used in the DMS. The aim is to use this model to test the performance and suitability of the 1553 Bus to the DMS under a number of alternative design scenarios.

Arozullah, Mohammed↗
NASA NTRS1980

The Seasat low rate data processing system

The development of the algorithms for data processing and distribution, the circuitry, and the performance of the Seasat low rate data processing system are reviewed. The system controls data from the radar altimeter, scatterometer, microwave radiometer, and the visible and IR radiometer for independent transmission of each instrument's readings. The downlink operates at 25 kb/sec, and a yearlong program of geophysical evaluation proceeded shortly after launch, allowing on-line engineering evaluation and alteration of the control algorithms in the system. Some data is preformatted for immediate distribution and storage in archival quality. A catalog and abstracts are provided to users allowing a RAM search from remote terminals for historical conditions. Procedures for verifying and altering the algorithms are detailed.

Brown, J. W.↗
NASA NTRS1997

Temperature Distribution in a Composite of Opaque and Semitransparent Spectral Layers

The analysis of radiative transfer becomes computationally complex for a composite when there are multiple layers and multiple spectral bands. A convenient analytical method is developed for combined radiation and conduction in a composite of alternating semitransparent and opaque layers. The semi- transparent layers absorb, scatter, and emit radiation, and spectral properties with large scattering are included. The two-flux method is used, and its applicability is verified by comparison with a basic solution in the literature. The differential equation in the two-flux method Is solved by deriving a Green's function. The solution technique is applied to analyze radiation effects in a multilayer zirconia thermal barrier coating with internal radiation shields for conditions in an aircraft engine combustor. The zirconia radiative properties are modeled by two spectral bands. Thin opaque layers within the coating are used to decrease radiant transmission that can degrade the zirconia insulating ability. With radiation shields, the temperature distributions more closely approach the opaque limit that provides the lowest metal wall temperatures.

Siegel, Robert↗
NASA NTRS1933

Ice Prevention on Aircraft by Means of Engine Exhaust Heat and a Technical Study of Heat Transmission from a Clark Y Airfoil

This investigation was conducted to study the practicability of employing heat as a means of preventing the formation of ice on airplane wings. The report relates essentially to technical problems regarding the extraction of heat from the exhaust gases and its proper distribution over the exposed surfaces. In this connection a separate study has been made to determine the variation of the coefficient of heat transmission along the chord of a Clark Y airfoil. Experiments on ice prevention both in the laboratory and in flight show conclusively that it is necessary to heat only the front portion of the wing surface to effect complete prevention. Experiments in flight show that a vapor-heating system which extracts heat from the exhaust and distributes it to the wings is an entirely practical and efficient method for preventing ice formation.

Theodorsen, Theodore↗
NASA NTRS1991

Real time quantitative imaging for semiconductor crystal growth, control and characterization

A quantitative real time image processing system has been developed which can be software-reconfigured for semiconductor processing and characterization tasks. In thermal imager mode, 2D temperature distributions of semiconductor melt surfaces (900-1600 C) can be obtained with temperature and spatial resolutions better than 0.5 C and 0.5 mm, respectively, as demonstrated by analysis of melt surface thermal distributions. Temporal and spatial image processing techniques and multitasking computational capabilities convert such thermal imaging into a multimode sensor for crystal growth control. A second configuration of the image processing engine in conjunction with bright and dark field transmission optics is used to nonintrusively determine the microdistribution of free charge carriers and submicron sized crystalline defects in semiconductors. The IR absorption characteristics of wafers are determined with 10-micron spatial resolution and, after calibration, are converted into charge carrier density.

Wargo, Michael J.↗
NASA NTRS2008

Assessment of Microphysical Models in the National Combustion Code (NCC) for Aircraft Particulate Emissions: Particle Loss in Sampling Lines

This paper at first describes the fluid network approach recently implemented into the National Combustion Code (NCC) for the simulation of transport of aerosols (volatile particles and soot) in the particulate sampling systems. This network-based approach complements the other two approaches already in the NCC, namely, the lower-order temporal approach and the CFD-based approach. The accuracy and the computational costs of these three approaches are then investigated in terms of their application to the prediction of particle losses through sample transmission and distribution lines. Their predictive capabilities are assessed by comparing the computed results with the experimental data. The present work will help establish standard methodologies for measuring the size and concentration of particles in high-temperature, high-velocity jet engine exhaust. Furthermore, the present work also represents the first step of a long term effort of validating physics-based tools for the prediction of aircraft particulate emissions.

Wey, Thomas↗
NASA NTRSDate not supplied

Microstructure Controlled Multi-Layer Porous Material Liner Tested On The Advanced Noise Control Fan

A novel concept of multilayer micro structurally controlled noise mitigation porous material was developed and experimentally validated in the laboratory by normal incidence impedance test. Extensive parametric studies were made to understand various parameters that influence acoustic absorption and transmission loss based on the test specimen size, particle size, porosity, pore size, and its distribution through the thickness. The results were reported in many publications. This work was focused on applying the concept and assessing the validity of the technology to aircraft turbomachine engines. The NASA Glenn Research Center’s Advanced Noise Control Fan (ANCF) low-speed test rig was selected. The liner insert required a 4-ft internal diameter cylinder with a 2-inch thick and 9-inch axial length. The liner was fabricated in eight segments and assembled in an aluminum test rig. The liner was tested for both tonal and broadband noise at the Notre Dame Turbomachinery Lab White Field test facility, where the ANCF is located. The study concludes that: Microstructurally controlled porous material is very effective in dissipating the sound energy; the liner is effective for tonal noise (2 to 13 dB reduction in noise levels) that constitutes the major part of the overall fan noise, especially the blade passing frequency which is generally the dominating component; Also, the liner is effective for broadband noise with reductions in sound pressure level of about 3 dB for the shaft order greater than 20. The proposed two-layer liner model demonstrated the validity of the concept. More studies are required to optimize the design.

Liner↗
NASA NTRS1992

Dynamic modeling of fluid transmission lines of the DSN 70-meter antennas by using a lumped parameter model

Fluid transmission lines and fittings were found to significantly affect the dynamic and steady state operation of the engineering system in which they are incorporated. Therefore, a better understanding of the operation of a system can be obtained by including the performance of the transmission lines and fittings within the system model. The most accurate model of a transmission line or fitting is obtained by using a distributed parameter model. However, a distributed parameter model tends to be very complex. This complexity can be avoided without significant loss of model accuracy by using a lumped parameter model when the length of the fluid path through the transmission line or fitting is short. This article develops a lumped parameter model for short fluid transmission lines and fittings, describes the conditions under which the model is valid, and presents the model parameters associated with the servo hydraulic system of the Deep Space Network (DSN) 70-meter antennas.

Bartos, R. D.↗
NASA NTRS1988

Measured and calculated acoustic attenuation rates of tuned resonator arrays for two surface impedance distribution models with flow

An experiment was performed to validate two analytical models for predicting low frequency attenuation of duct liner configurations built from an array of seven resonators that could be individually tuned via adjustable cavity depths. These analytical models had previously been developed for high frequency aero-engine inlet duct liner design. In the low frequency application, the liner surface impedance distribution is unavoidably spatially varying by virtue of available fabrication techniques. The characteristic length of this spatial variation may be a significant fraction of the acoustic wavelength. Comparison of measured and predicted attenuation rates and transmission losses for both modal decomposition and finite element propagation models were in good to excellent agreement for a test frequency range that included the first and second cavity resonance frequencies. This was true for either of two surface impedance distribution modeling procedures used to simplify the impedance boundary conditions. In the presence of mean flow, measurements revealed a fine scale structure of acoustic hot spots in the attenuation and phase profiles. These details were accurately predicted by the finite element model. Since no impedance changes due to mean flow were assumed, it is concluded that this fine scale structure was due to convective effects of the mean flow interacting with the surface impedance nonuniformities.

Parrott, Tony L.↗
NASA NTRS2005

Program Computes Sound Pressures at Rocket Launches

Launch Vehicle External Sound Pressure is a computer program that predicts the ignition overpressure and the acoustic pressure on the surfaces and in the vicinity of a rocket and launch pad during launch. The program generates a graphical user interface (GUI) that gathers input data from the user. These data include the critical dimensions of the rocket and of any launch-pad structures that may act as acoustic reflectors, the size and shape of the exhaust duct or flame deflector, and geometrical and operational parameters of the rocket engine. For the ignition-overpressure calculations, histories of the chamber pressure and mass flow rate also are required. Once the GUI has gathered the input data, it feeds them to ignition-overpressure and launch-acoustics routines, which are based on several approximate mathematical models of distributed sources, transmission, and reflection of acoustic waves. The output of the program includes ignition overpressures and acoustic pressures at specified locations.

Ogg, Gary↗
NASA NTRS2018

Use of Nack Oriented Reliable Multicast (NORM) Protocol for Transport of Spacecraft Telemetry in Ground Networks

Frequently it is necessary to distribute spacecraft telemetry to multiple destinations on Internet Protocol (IP) networks. There are various methods of delivering this data, but when the data is high rate and there are many destinations IP multicast provides the best solution from a network perspective. However, IP multicast only supports the User Datagram Protocol (UDP) which is connectionless and unreliable. This nature of UDP and by extension the low priority treatment of UDP packets by some network hardware creates a difficult environment for distribution of high rate telemetry to a number of recipients over IP networks. NACK (Negative ACKnowledgment) Oriented Reliable Multicast (NORM) is defined by IETF (Internet Engineering Task Force) RFC (Request for Comments) 5740 in 2009 by B. Adamson et al. NORM provides a mechanism of retransmission and or forward error correction for UDP packets, potentially overcoming the limits of UDP for the transmission of spacecraft telemetry. Marshall Space Flight Center’s (MSFC) Huntsville Operations Support Center (HOSC) manages the delivery of the International Space Station (ISS) payload science and health data. The ISS IP Ground Routed (IIGoR) network provides the delivery of the data from the ground stations to the control centers. HOSC personnel have been experimenting with the use of NORM on the link between the ground stations and the front end processor equipment in Huntsville, AL.

Baldwin, Patrick A.↗
NASA NTRS1955

Adaptation of Combustion Principles to Aircraft Propulsion: Basic Considerations in the Combustion of Hydrocarbon Fuels with Air - Volume I

The report summarizes source material on combustion for flight-propulsion engineers. First, several chapters review fundamental processes such as fuel-air mixture preparation, gas flow and mixing, flammability and ignition, flame propagation in both homogenous and heterogenous media, flame stabilization, combustion oscillations, and smoke and carbon formation. The practical significance and the relation of these processes to theory are presented. A second series of chapters describes the observed performance and design problems of engine combustors of the principal types. An attempt is made to interpret performance in terms of the fundamental processes and theories previously reviewed. Third, the design of high-speed combustion systems is discussed. Combustor design principles that can be established from basic considerations and from experience with actual combustors are described. Finally, future requirements for aircraft engine combustion systems are examined.

THEORIES - COMBUSTION↗
NASA NTRS2000

Laser Transmission Measurements of Soot Extinction Coefficients in the Exhaust Plume of the X-34 60K-lb Thrust Fastrac Rocket Engine

A four-channel laser transmissometer has been used to probe the soot content of the exhaust plume of the X-34 60k-lb thrust Fastrac rocket engine at NASA's Marshall Space Flight Center. The transmission measurements were made at an axial location approximately equal 1.65 nozzle diameters from the exit plane and are interpreted in terms of homogeneous radial zones to yield extinction coefficients from 0.5-8.4 per meter. The corresponding soot mass density, spatially averaged over the plume cross section, is, for Rayleigh particles, approximately equal 0.7 microgram/cc, and alternative particle distributions are briefly considered. Absolute plume radiance at the laser wavelength (515 nm) is estimated from the data at approximately equal 2,200 K equivalent blackbody temperature, and temporal correlations in emission from several spatial locations are noted.

Dobson, C. C.↗
NASA NTRS2000

Laser Transmission Measurements of Soot Extinction Coefficients in the Exhaust Plume of the X-34 60k-lb Thrust Fastrac Rocket Engine

A four-channel laser transmissometer has been used to probe the soot content of the exhaust plume of the X-34 60k-lb thrust Fastrac rocket engine at NASA's Marshall Space Flight Center. The transmission measurements were made at an axial location about equal 1.65 nozzle diameters from the exit plane and are interpreted in terms of homogeneous radial zones to yield extinction coefficients from 0.5-8.4 per meter. The corresponding soot mass density, spatially averaged over the plume cross section, is, for Rayleigh particles, approximately equal to 0.7 micrograms/cubic cm and alternative particle distributions are briefly considered. Absolute plume radiance at the laser wavelength (515 nm) is estimated from the data at approximately equal to 2.200 K equivalent blackbody temperature, and temporal correlations in emission from several spatial locations are noted.

Dobson, C. C.↗
NASA NTRS1997

Electrical signal transmission and gap junction regulation in a bone cell network: a cable model for an osteon

A cable model is formulated to estimate the spatial distribution of intracellular electric potential and current, from the cement line to the lumen of an osteon, as the frequency of the loading and the conductance of the gap junction are altered. The model predicts that the characteristic diffusion time for the spread of current along the membrane of the osteocytic processes, 0.03 sec, is nearly the same as the predicted pore pressure relaxation time in Zeng et al. (Annals of Biomedical Engineering. 1994) for the draining of the bone fluid into the osteonal canal. This approximate equality of characteristic times causes the cable to behave as a high-pass, low-pass filter cascade with a maximum in the spectral response for the intracellular potential at approximately 30 Hz. This behavior could be related to the experiments of Rubin and McLeod (Osteoporosis, Academic Press, 1996) which show that live bone appears to be selectively responsive to mechanical loading in a specific frequency range (15-30 Hz) for several species.

NASA Discipline Musculoskeletal↗