SEARCH · Search NASA

Results for “Environmental Barrier Coatings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Evaluating steam oxidation kinetics of environmental barrier coatings

Environmental barrier coatings (EBCs) are a commercially proven means of protecting SiC-based materials in gas turbine environments. However, there are little specific data in the literature on the impact of coatings like Yb 2 Si 2 O 7 on preventing accelerated SiO 2 growth in the presence of H 2 O. Quantification of reduced rates are necessary for evaluating and comparing EBC effectiveness and incorporation of silica growth rates into future EBC lifetime models. In this study, baseline kinetics of silica formation on bare Si and chemically vapor deposited (CVD) SiC in the 1250–1425 °C range were obtained via 100 h isothermal exposures in dry air and steam environments utilizing a SiC reaction tube to mitigate specimen volatility. An Arrhenius plot of the resulting rates was constructed, representing baseline minimum and maximum rates for Si and SiC oxidation at ambient pressure. Various EBC systems on CVD SiC substrates including air plasma sprayed (APS) EBCs with and without a Si bond coating and with surface roughening to enhance Yb 2 Si 2 O 7 adhesion were subjected to 1-h furnace cycle testing in air with 90vol%H 2 O at 1250–1350°C for up to 500 cycles. After exposure, silica formation rates were measured and compared to the baseline rates to assess EBC effectiveness, where EBC effectiveness is gauged as the propensity to reduce underlying rates of silica formation. With a Si bond coating, a ~180 µm Yb 2 Si 2 O 7 (YbDS) top coating reduced rates over the entire 1250°-1350°C range. Without a Si bond coating, ~60 µm (YbDS) coatings deposited directly onto CVD SiC exhibited poor adhesion, and had to be deposited onto substrates with enhanced roughness at 1350°C. Finally, while exhibiting good adhesion at 1350°C, overall the single layer YbDS coating exhibited a decreasing effectiveness from 1250° to 1350°C.

36 MATERIALS SCIENCE↗

DOE OSTI2023

FWP FEAA149: “Next Generation Environmental Barrier Coatings”

Environmental barrier coatings (EBCs) are required coatings for utilization of SiC/SiC ceramic matrix composite (CMC) components in gas turbines, where the EBC represents the life-limiting factor for such components. EBC/CMC systems have shown success in aero-engine applications with increased turbine inlet temperatures and improved efficiencies, which are achieved through higher temperature stability, lower density, and decreased reliance on cooling air compared to traditional superalloys. While industrial gas turbines (IGTs) do not currently utilize SiC/SiC CMCs, the current shift towards low-carbon or carbon-free fuel sources for power generation could result in a need for EBC/CMC components with higher temperature capabilities. In this work, three tasks were outlined to improve understanding of EBC lifetimes to encourage use in IGTs with carbon-free fuel such as hydrogen: 1. Define the bond coating oxidation kinetics and EBC failure criteria, 2. Measure thermal expansion coefficients of each layered material, and 3. Perform advanced characterization and modeling to assess EBC lifetimes. Cyclic steam oxidation tests were conducted on various EBC/Si/SiC chemistries and EBC/SiC architectures to define substrate oxidation kinetics and EBC failure modes. An open-source code was developed to quantify the undulating thermally grown oxide thickness with thousands of measurements from specimen cross-section images. Bond coating oxidation kinetics were determined and used to develop a kinetic and thermodynamic model for predicting EBC lifetimes. High-temperature Raman spectroscopy was utilized for determining the SiO 2 thermally grown oxide phase transformation as the life-limiting feature for EBCs. Model efforts supported the claim that the SiO 2 phase transformation causes elevated stress during thermal cycling with associated cracking that decreases the adhesion strength of the EBC, eventually resulting in coating spallation. The finite element model subroutine will be made publicly available upon internal review. Further development of an EBC lifetime model for IGTs involves definition of a critical SiO 2 thickness for EBC spallation and must also consider both environmental (gas velocity, pressure, etc.) and specimen (EBC dopants, layer architectures, etc.) effects into predicted bond coating oxidation kinetics for long-lifetime components.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Insights into oxygen diffusion in rare earth disilicate environmental barrier coatings

Environmental barrier coatings (EBC) are crucial for the use of SiC-based ceramic matrix composites in high-temperature combustion environments, yet knowledge of oxygen diffusion in these coatings is limited. This study investigates oxygen diffusion dynamics in the β-RE 2 Si 2 O 7 system to minimize oxygen penetration in rare earth disilicates. We analyze defect formation energy under varying oxygen conditions, identifying key diffusion mechanisms. In oxygen-rich environments, the most favorable neutral interstitial oxygen diffuses along the [110] direction. In oxygen-poor conditions, neutral oxygen vacancies rotate around Y and Si atoms, exhibiting a diffusivity of 6.59×10 −22 m 2 /s at 1500 K for β-Yb 2 Si 2 O 7 . Under intermediate oxygen levels, charged interstitial oxygen diffuses via concerted interstitialcy along the [001] direction with a diffusivity of 6.21×10 −17 m 2 /s. Additionally, alloying rare earth Y with Er and Yb increases diffusion barriers, contributing to improved EBC performance in extreme environments. The insights gained provides valuable guidance for designing robust coatings tailored to withstand extreme operational environments.

36 MATERIALS SCIENCE↗

DOE OSTI2025

A statistical representation of bond coating oxidation under environmental barrier coatings

Environmental barrier coatings (EBCs) protect SiC-based ceramic matrix composites (CMCs) in turbine hot sections from high-temperature volatilization in combustion gases. The formation of a SiO 2 thermally grown oxide (TGO) is expected under the EBC after long-term operation. The oxidation resistance of the EBC is understood as a life-limiting factor for the CMC, and this work predicts long-term oxidation behavior under EBCs through a simple statistical approach. Specimens were exposed to 1350°C isothermal conditions for 100-h thermal cycles in flowing steam for up to 1000 h. The EBC morphology, SiO 2 thickness, and SiO 2 cracking behavior were assessed. Using thousands of SiO 2 thickness measurements across many millimeters of the interface, a realistic representation of the entire TGO was captured via a lognormal distribution. The lognormal fit parameters were extrapolated out to 25 000 h to assess the degree of SiO 2 growth, the spread of SiO 2 thicknesses related to the rough oxidizing interface, and percentages of the intermediate bond coating consumed. In conclusion, local interfacial defects from the coating deposition process are identified as local failure points for EBC—CMC systems.

SiO 2↗

DOE OSTI2021

Accelerated oxidation during 1350°C cycling of ytterbium silicate environmental barrier coatings

We report environmental barrier coatings (EBCs) will be needed to protect SiC-based ceramic matrix composite components for the next generation of high-efficiency industrial gas turbines (IGTs). The IGT application will require ≥25 kh lifetimes, and little data are available on EBC failure mechanisms, particularly at ≥1300°C. Initial 1-h furnace cycle testing at 1350°C in 90 vol% H 2 O/10 vol% air was conducted ≥1000 cycles on thermally sprayed ytterbium disilicate (YbDS) coatings with and without an Si bond coating. By ≥1000 h, both EBCs formed thick, highly cracked, and fully crystalline cristobalite scales. Comparison of thermally grown oxide (TGO) microstructure and kinetics to isothermal rates of Si and SiC steam oxidation indicated a departure from slow-growing parabolic growth to more rapid rates of silica formation. Possible mechanisms and implications for this acceleration are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2020

In situ characterization of foreign object damage (FOD) in environmental-barrier-coated silicon carbide (SiC) ceramic

Environmental barrier coatings (EBCs) protect advanced ceramics and ceramic matrix composites (CMCs) from oxidation and corrosion in gas turbine engine environments. Foreign object damage (FOD), where debris impact the protective coatings, is a critical hazard which limits the turbine durability. Despite previous efforts to understand FOD in EBCs, a detailed understanding of the fundamental transient damage mechanisms is still lacking. In the current work, the real-time FOD behavior of a Mullite / Silicon EBC was visualized via a dynamic synchrotron X-ray source in phase contrast imaging (PCI) configuration. Prior to the in situ FOD experiments, the microstructure and composition of the coating were respectively characterized using a scanning electron microscope (SEM) and X-ray diffraction (XRD). The variation in the properties of the debris was modeled by ~ 1.5 mm diameter Partially Stabilized Zirconia (PSZ) and Silicon Nitride (Si 3 N 4 ) spheres. A modified light-gas gun setup, synchronized with the X-ray beam, was used to propel the projectiles at velocities ranging between 300 and 355 m·s -1 . Coated samples were impacted under a fully backed support configuration and at normal incidence. Coating penetration and delamination, as well as projectile deformation at the bond coat resulted for FOD by PSZ spheres. Comparatively, projectile fracture, with subsequent rebound of fragments, as well as complete coating penetration and delamination at the substrate interface occurred for FOD by Si 3 N 4 spheres. It should be noted that only cone cracking was observed for FOD by PSZ spheres while back surface cracking was present for both projectile types. Qualitative understanding of the driving forces for the observed damage mechanisms were provided.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Advanced high temperature environmental barrier coating for SiC/SiC ceramic matrix composites

Advanced environmental barrier coating bond coat systems with higher temperature capabilities and environmental resistance are disclosed. These bond coat systems can be applied to ceramic substrates such as SiC/SiC ceramic matrix composite substrates, and can provide protection from extreme temperature, mechanical loading and environmental conditions, such as in high temperature gas turbines. Example bond coat systems can include either an advanced silicon/silicide component, an oxide/silicate component, or a combination thereof.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Advanced high temperature environmental barrier coating systems for SiC/SiC ceramic matrix composites

36 MATERIALS SCIENCE↗

DOE OSTI2022

Steam oxidation and microstructural evolution of rare earth silicate environmental barrier coatings

A primary failure mode for environmental barrier coatings (EBCs) on SiC ceramic matrix composites (CMCs) is the oxidation of the intermediate Si-bond coating, where the formation of SiO 2 at the bond coating–EBC interface results in debonding and spallation. This work compares the microstructure evolution and steam oxidation kinetics of the Si-bond coating beneath yttrium/ytterbium disilicate ((Y/Yb)DS) and ytterbium disilicate/monosilicate (YbDS/YbMS) EBCs to better understand the impact of EBC composition on oxidation kinetics. After 500 1-h cycles at 1350°C, (Y/Yb)DS displayed a decreasing concentration of the monosilicate minor phase and increasing concentration of porosity as furnace cycling time increased, whereas the YbDS/YbMS EBC displayed negligible microstructural evolution. For both EBC systems, thermally grown oxide growth rates in steam were found to increase by approximately an order magnitude compared to dry air oxidation. The (Y/Yb)DS EBC displayed a reduced steam oxidation rate compared to YbDS/YbMS.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Steam oxidation of ytterbium disilicate environmental barrier coatings with and without a silicon bond coat

The current generation of multilayer Si/Yb 2 Si 2 O 7 environmental barrier coatings (EBCs) are temperature limited by the melting point of Si, 1414°C. To investigate higher temperature EBCs, the cyclic steam oxidation of EBCs comprised of a single layer of ytterbium disilicate (YbDS) was compared to multilayered Si/YbDS EBCs, both deposited on SiC substrates using atmospheric plasma spray. In this work, after 500 1-h cycles at 1300°C in 90 vol%H2O-10 vol%air with a gas velocity of 1.5 cm/s, both multilayer Si/YbDS and single layer YbDS grew thinner silica scales than bare SiC, with the single layer YbDS forming the thinnest scale. Both coatings remained fully adherent and showed no signs of delamination. Silica scales formed on the single layer coating were significantly more homogeneous and possessed a markedly lower degree of cracking compared to the multilayered EBC. The single layer EBC also was exposed at 1425°C in steam with a gas velocity of 14 cm/s in an alumina reaction tube. The EBC reduced specimen mass loss compared to bare SiC but formed an extensive 2nd phase aluminosilicate reaction product. A similar reaction product was observed to form on some regions of the bare SiC specimen and appeared to partially inhibit silica volatilization. The 1425°C steam exposures were repeated with a SiC reaction tube and no 2nd phase reaction product was observed to form on the single layer EBC or bare SiC.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Phase-Field Modeling of Damage Evolution in Ceramic Matrix Composite (CMC) and Environmental Barrier Coating (EBC)

Ceramic matrix composites (CMCs) protected by environmental barrier coatings (EBCs) present a promising materials solution for next generation gas turbines. Developments of more robust and efficient EBCs and mechanically tougher CMCs are thus of significant technological importance. Here we develop a phase-field modeling framework that incorporates the thermally grown oxide (TGO), recognized as a critical factor for degradation and failure of EBCs. We simulate crack growth in the TGO and the potential extension into the bond coat / CMC substrate. The model efficiently takes account of the large inelastic deformation induced by the severe volume expansion of TGO, thanks to our recently developed, so-called incremental realization of inelastic deformation (IRID) algorithm. A phase-field model is built for damage evolution in CMCs including crack growth and interfacial sliding. The effects of fiber layout and interfacial sliding on the macroscopic toughness of CMCs are revealed by large-scale simulations and compared to experiments.

advanced energy systems and materials↗

DOE OSTI2024

Environmental barrier coatings on SiC without a silicon bond coating: oxidation resistance, failure modes, and future improvements

Environmental barrier coatings (EBCs) are used to mitigate chemical reactions between SiC ceramic matrix composite (CMC) components and the H 2 O in combustion gas in turbine hot sections. CMCs are currently temperature-limited by the Si-bond coating, which melts at ~ 1414 °C. This work explores EBCs where the bond coating was removed to achieve higher operating temperatures. Various versions of enhanced roughness SiC were utilized to improve EBC adhesion to the substrates prior to 1 h furnace cycle testing in steam at 1250–1425 °C. The enhanced SiC roughness resulted in short coating lifetimes as the roughness was oxidized away with SiO 2 formation. Further, isothermal furnace exposures at 1400–1600 °C showed Yb 2 Si 2 O 7 /Yb 2 SiO 5 EBC microstructural changes, resulting in premature debonding from the substrates. Finally, this work provides baseline requirements for the development of both next-generation EBCs and bond coating strategies to overcome the current limitation of the Si-bond coating melting temperature.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Theoretical Prediction of Thermal Expansion Anisotropy for Y 2 Si 2 O 7 Environmental Barrier Coatings Using a Deep Neural Network Potential and Comparison to Experiment

Environmental barrier coatings (EBCs) are an enabling technology for silicon carbide (SiC)-based ceramic matrix composites (CMCs) in extreme environments such as gas turbine engines. However, the development of new coating systems is hindered by the large design space and difficulty in predicting the properties for these materials. Density Functional Theory (DFT) has successfully been used to model and predict some thermodynamic and thermo-mechanical properties of high-temperature ceramics for EBCs, although these calculations are challenging due to their high computational costs. In this work, we use machine learning to train a deep neural network potential (DNP) for Y 2 Si 2 O 7 , which is then applied to calculate the thermodynamic and thermo-mechanical properties at near-DFT accuracy much faster and using less computational resources than DFT. We use this DNP to predict the phonon-based thermodynamic properties of Y 2 Si 2 O 7 with good agreement to DFT and experiments. We also utilize the DNP to calculate the anisotropic, lattice direction-dependent coefficients of thermal expansion (CTEs) for Y 2 Si 2 O 7 . Molecular dynamics trajectories using the DNP correctly demonstrate the accurate prediction of the anisotropy of the CTE in good agreement with the diffraction experiments. In the future, this DNP could be applied to accelerate additional property calculations for Y 2 Si 2 O 7 compared to DFT or experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Phase-field modeling of thermally-grown oxide and damage evolution in environmental barrier coatings

Silicon carbide-based ceramic matrix composites protected by environmental barrier coatings (EBCs) present a promising materials solution for next-generation gas turbines. Developing more robust and efficient EBCs is therefore of significant technological importance. During the service in high-temperature oxidative environments, there is a thermally grown oxide (TGO) layer, spontaneously formed in the EBC system. TGO is recognized as a critical factor for the degradation and failure of EBCs, yet the detailed mechanisms of TGO growth and its effect on EBC failure remain unclear. In this study we develop a comprehensive chemo-mechano-phase-field model to simulate growth of the TGO in EBCs, factoring in creep and deformation, and especially the cracking behaviors. The volume expansion due to TGO growth and the resulting large inelastic deformation are addressed by using our recently developed, so-called incremental realization of inelastic deformation (IRID) algorithm, in combination with an adapted Hu-Chen spectral solver for elasticity. Simulations of TGO growth are performed considering different growth modes of TGOs determined mainly by the ratio of oxidant permeability in the topcoat to that in the TGO itself. Large-scale three-dimensional (3D) simulations are performed to model the formation of interconnecting vertical/channel cracks (often called ‘mud cracks’). The simulated crack morphology are in excellent agreement with the experimental observations from the literature. The simulations also provide insights into the cracking of EBCs and its dependence on the structure and constituent properties of the coating system. Furthermore, these results demonstrate the developed damage model can be a useful tool for design of more durable EBCs.

Cracking↗

DOE OSTI2023

Environmental barrier coatings on enhanced roughness SiC: Effect of plasma spraying conditions on properties and performance

Environmental barrier coatings for SiC/SiC composites are limited by the melting temperature of the Si bond coating near 1414°C. Systems without a bond coating may be required for future turbine applications where material temperatures go beyond 1350 °C. Here, enhanced roughness SiC substrates were developed to assess coating adhesion without the bond coating. Two EBCs with different YbMS/YbDS ratios were produced via modified plasma spraying parameters. Coating microstructure, thermal expansion, and modulus were measured for comparison of coating properties. Cyclic steam exposures at 1350°C were performed to assess oxidation resistance. The EBC with increased concentration of Yb 2 SiO 5 secondary phase displayed a higher CTE, which is typically expected to decrease adhesion lifetimes due to an increase in stress upon thermal cycling. Yet, the EBC chemistry with increased Yb 2 SiO 5 concentration was able to experience longer cycling times prior to coating delamination, likely due to interface interactions with the substrate and the thermally grown oxide.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Holistic comparison of environmental barrier coating material candidates through design of a figure of merit

The first figure of merit for environmental barrier coating (EBC) materials was designed through a ranking system for material properties pertaining to established EBC failure modes in service. Seven past, present, and novel EBC candidate materials were used in the figure of merit design: SiO 2 , Ba 0.75 Sr 0.25 Al 2 Si 2 O 8 (BSAS), HfSiO 4 , Yb 2 Si 2 O 7 , Yb 2 SiO 5 , Yb 2 O 3 , and YbPO 4 . Utilizing compiled data from the literature, the presented figure of merit verified Yb 2 Si 2 O 7 as the state-of-the-art candidate with optimal EBC properties and inferred that YbPO 4 should be considered as a potentially viable EBC material candidate. Further, the figure of merit allows for a holistic comparison of EBC candidates and informs experimental and computational search efforts for next-generation complex EBCs. Clear knowledge gaps found through this work include CaO–MgO–Al 2 O 3 –SiO 2 (CMAS)-resistant coatings, EBC lifetimes before delamination, and oxidant diffusion rates in relevant EBC microstructures. It was shown that while some materials show promise for solving a single key failure mode for EBCs (i.e., CMAS reactivity), a community-wide goal should be placed on materials development to achieve acceptable resistance against all major failure modes, which are interconnected. Novel compositionally complex EBC materials, in addition to layered EBC architectures, show promise for the optimization of material properties for long-lifetime EBCs in combustion environments.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Design and Performance Testing of Low-cost Multicomponent Rare Earth Disilicate Environmental Barrier Coatings

Presentation for the 2025 Materials Science & Technology Conference summarizing NETL work involving development and testing of environmental barrier coatings for protecting ceramic matrix composites in high efficiency gas turbines.

environmental barrier coatings↗

DOE OSTI2022

Dry air cyclic oxidation of mixed Y/Yb disilicate environmental barrier coatings and bare silica formers

Here mixed Y and Yb disilicate coatings (Y/Yb)DS have been proposed as dual function thermal and environmental barrier coatings (EBCs) for protecting SiC-based ceramic matrix composites in gas-turbine environments. As an initial step, the 1350 °C dry air cyclic oxidation of atmospheric plasma sprayed (Y 1.2 /Yb 0.8 )DS and ytterbium disilicate/ytterbium monosilicate (YbDS/YbMS) EBCs deposited onto Si bond coatings was compared. As a baseline for evaluating EBC oxidant permeability, the dry air cyclic oxidation scale growth rates for bare silica formers (SiC, Si) were also measured and were consistently higher than rates previously measured after isothermal oxidation. Regarding Si bond coat oxidation rates underlying (Y/Yb)DS and YbDS/YbMS EBCs, the thinner silica scale formed under the thinner and denser (Y/Yb)DS coatings suggested a lower oxidant permeability than YbDS/YbMS. After 500 1-h cycles, the (Y/Yb)DS coating was comprised of only the β-polymorph disilicate and minor amounts of the X-2 phase monosilicate phase. Negligible differences in oxidation kinetics for (Y/Yb)DS coatings over the 90 – 240 µm thickness range were observed.

36 MATERIALS SCIENCE↗