Search NASA⌕ Search

SEARCH · Search NASA

Results for “Experimental Validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Modeling and experimental validation of a W f /W-fabrication by chemical vapor deposition and infiltration

Tungsten (W) has a unique combination of excellent thermal properties, low sputter yield, low hydrogen retention, and acceptable activation. Therefore, W is presently the main candidate for the first wall material in future fusion devices. However, its intrinsic brittleness and its further embrittlement during operation bears the risk of a sudden and catastrophic component failure. As a countermeasure, tungsten fiber-reinforced tungsten (W f /W) with extrinsic toughening is being developed. A possible synthesis route is chemical vapor deposition (CVD) using heated W fabrics as substrate. The challenge is that the growing CVD-W can isolate domains from precursor access leading to strength-reducing pores. To deepen the process understanding and to optimize the CVD parameters, models were developed with COMSOL Multiphysics and validated experimentally. W deposition rate equations as function of the temperature and the partial pressures of the precursors H 2 and WF 6 were experimentally validated in previous work. In the present article, these equations are applied to obtain partial pressures within the CVD reactor. The results are taken as input for transient simulations in the microscale, in which W coatings, growing onto multiple adjacent W fibers, were simulated via mesh deformation and remeshing. The surface-to-surface contact of the W coatings and the corresponding potential pore formation were simulated by implementing sophisticated deposition rate stop conditions. Within the measuring uncertainties of ≃ ±1%, the models are validated successfully by experimental comparison regarding the deposition rate, pore structure, and relative densities ranging from 0.6 to 0.9.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Inhibition of asphaltene aggregation using deep eutectic solvents: COSMO-RS calculations and experimental validation

Asphaltene precipitation/deposition adversely affects various oil and gas processes, such as oil recovery, transportation, and petroleum processing. The resulting increase in viscosity of crude oil decreases distillate yields creating unstable phase separation. Deep eutectic solvents (DESs) have recently gained interest as inhibitors of asphaltene aggregation. The goal of the present study is to derive the mechanism of inhibition of petroleum asphaltene aggregation by a novel screening of DESs. An archipelago-based chemical structure of asphaltene was adopted for performing quantum chemical calculations. The structure was used in the conductor-like screening model for real solvents (COSMO-RS) model to screen potential DESs for asphaltene precipitation. It was found that DESs containing thymol were the most promising of the 153 DES combinations screened. The COSMO-RS predictions were validated experimentally using solubility data of asphaltene in DESs. Among the studied DESs, thymol-diphenyl ether provided the highest solubility for asphaltene, which was further validated using the experimental and the COSMO-RS predicted data. In addition, to characterize the structural interactions between asphaltene and DESs, Fourier transform infrared (FTIR) spectroscopy and nuclear magnetic resonance (NMR) measurements were performed. It was found that strong interaction between asphaltene and the DESs is responsible for the higher asphaltene dispersion. Finally, the present approach opens pathways to rationally design and understand the impact of structural variation of DESs based on their interactions with asphaltene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

First-principles calculation of lattice distortions in four single phase high entropy alloys with experimental validation

Exceptional properties of high entropy alloys (HEAs) are attributed to the disordered random solid solution of multiple alloying elements. Despite numerous studies, the fundamental understanding at the electronic and atomic levels is still missing. We report a comparative study of four fcc HEAs of NiFeCoCr and NiFeCoCrX (X = Mn, Cu, or Pd) based on ab initio calculations using large supercells with 500 atoms in equal composition. After fully optimizing their structures using the VASP package, their electronic structure, interatomic bonding, partial charge distribution, and mechanical properties are calculated and compared, revealing the intricate interdependence among them. A novel parameter based on the quantum mechanical metric for internal cohesion, the total bond order density (TBOD), is used to interpret the calculated properties. The highest TBOD is found in Cantor alloy NiFeCoCrMn but lower in NiFeCoCrPd. The atomic radii vary depending on their local chemical environment. The resulting lattice distortions is validated experimentally in NiFeCoCrMn and NiFeCoCrPd. Moreover, modeling of Cu and Pd clustering in the supercell shows they have lower total energy in agreement with the observation of Cu-enhanced nano-participates in NiFeCoCrCu and Pd-induced concentration wave in NiFeCoCrPd HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Large-scale experimental validation of thermochemical water-splitting oxides discovered by defect graph neural networks

Thermochemical water-splitting (TCH) based on 2-step thermal redox cycles in metal oxides is a promising approach to generating H 2 , but state-of-the-art (SOTA) CeO 2 has several practical limitations, which has motivated continued materials discovery efforts in this field. Here, in this study, we improve upon a SOTA defect graph neural network (dGNN) surrogate model's oxygen vacancy predictions and combine them with materials project phase diagrams to down-select and discover structurally diverse, experimentally known metal oxides whose TCH performance was previously unknown. Amongst twelve candidates selected based on our high-throughput screening and down-selection criteria, we achieved ∼80% accuracy in identifying materials with stable redox cycling and hydrogen production in stagnation flow reactor water-splitting experiments. Closer to 100% accuracy can be achieved if higher-accuracy, hybrid DFT-predicted vacancy formation energies were computed and used in lieu of the most uncertain dGNN-based screening predictions, as they correct false positives to true negatives. Notably, two discovered candidates, Sr 3 PrMn 2 O 8 and Ba 2 Fe 2 O 5 , display hydrogen yields greater than CeO 2 under specific redox conditions. In conclusion, these results demonstrate our ability to computationally predict and experimentally validate promising candidate TCH materials that have the potential to compete with CeO 2 .

08 HYDROGEN↗
DOE OSTI2022

Experimental validation of multiphysics model simulations of the thermal response of a cement clinker rotary kiln at laboratory scale

Abstract An increasing demand for buildings, transportation systems and civil infrastructure development has driven expansion of cement consumption world‐wide, producing a significant increase in related global energy demand. With approximately 7% of the world‐wide industrial energy consumption (10.7 exajoules [EJ]), the cement industry is the third most energy intensive industrial processes and a key component for concrete, the most consumed composite material in the global construction industry. In cement manufacturing, the cement kiln accounts for most of the energy consumption in the production process. As the heart of a cement plant, the cement kiln is where the kiln feed primarily containing calcium oxide (CaO), silica (SiO 2 ), alumina (Al 2 O 3 ), and iron (Fe 2 O 3 ) are thermally and chemically transformed into clinker minerals. The presented work developed a multiphysics model, designed and built a laboratory‐scale rotary cement clinker kiln, and produced cement clinker at laboratory‐scale. The model was developed to study the interaction between the various thermal, fluid dynamic and chemical interactions involved in the sintering process used to form Portland cement clinker in an effort to reduce energy use. The analytical model was validated through experimental testing using a unique laboratory‐scale rotary cement kiln developed during the investigation. Also demonstrated was the feasibility of producing clinker at laboratory scale. This modeling and lab scale tests were designed to better understand the clinker sintering process so that operational and quality decisions can be made to optimize energy consumption without compromising cement clinker quality. The computational fluid dynamics modeling was developed in COMSOL Multiphysics 6.0. The characteristics of the combustion fluid flow, concentration of species, temperature and heat transfer were studied for a turbulent flow of methane (CH 4 ) gas and oxygen (O 2 ). Theory suggests that heat transfer impacts the cement production process but the multiphysics model more accurately describes the convection, conduction, and radiant heat transfer in the kilning process and thus allows for a better understanding of the energy exchange driving the chemical reactions that produce Portland cement. Clinker minerals were formed because of appropriate burning conditions implemented during experimental model validation.

Tabares, Juan David↗
DOE OSTI2025

Scalable phononic metamaterials: Tunable bandgap design and multi-scale experimental validation

Phononic metamaterials offer unprecedented control over wave propagation, making them essential for applications such as vibration isolation, waveguiding, and acoustic filtering. However, achieving scalable and precisely tunable bandgap properties across different length scales remains challenging. This study presents a user-friendly design framework for phononic metamaterials, enabling ultra-wide bandgap tunability (B/ω c ratios up to 172 %) across multiple frequency ranges and scales. Using finite element simulations of a Yablonovite-inspired unit cell, we establish a comprehensive parametric design space that illustrates how geometric parameters, such as sphere size and beam diameter, controls bandgap width and frequency. The scalability and robustness of the framework are validated through experimental testing on additively manufactured structures at both macro (10 mm) and micro (80 µm) scales, fabricated using Stereolithography and Two-Photon Polymerization. Transmission loss measurements, conducted with piezoelectric transducers and laser vibrometry, closely match simulations in the kHz and MHz frequency ranges, confirming the reliability and consistency of the bandgap behavior across scales. This work bridges theory and experiments at multiple scales, offering a practical methodology for the rapid design of phononic metamaterials and expanding their potential for diverse applications across a broad range of frequencies.

36 MATERIALS SCIENCE↗
NASA NTRS1991

Active flutter suppression - Control system design and experimental validation

The synthesis and experimental validation of an active flutter suppression controller for the Active Flexible Wing wind-tunnel model is presented. The design is accomplished with traditional root locus and Nyquist methods using interactive computer graphics tools and with extensive use of simulation-based analysis. The design approach uses a fundamental understanding of the flutter mechanism to formulate a simple controller structure to meet stringent design specifications. Experimentally, the flutter suppression controller succeeded in simultaneous suppression of two flutter modes, significantly increasing the flutter dynamic pressure despite errors in flutter dynamic pressure and flutter frequency in the mathematical model. The flutter suppression controller was also successfully operated in combination with a roll maneuver controller to perform flutter suppression during rapid rolling maneuvers.

Waszak, Martin R.↗
NASA NTRS1992

Flutter suppression for the Active Flexible Wing - Control system design and experimental validation

The synthesis and experimental validation of a control law for an active flutter suppression system for the Active Flexible Wing wind-tunnel model is presented. The design was accomplished with traditional root locus and Nyquist methods using interactive computer graphics tools and with extensive use of simulation-based analysis. The design approach relied on a fundamental understanding of the flutter mechanism to formulate understanding of the flutter mechanism to formulate a simple control law structure. Experimentally, the flutter suppression controller succeeded in simultaneous suppression of two flutter modes, significantly increasing the flutter dynamic pressure despite errors in the design model. The flutter suppression controller was also successfully operated in combination with a rolling maneuver controller to perform flutter suppression during rapid rolling maneuvers.

Waszak, M. R.↗
NASA NTRS1984

Supersonic, nonlinear, attached-flow wing design for high lift with experimental validation

Results of the experimental validation are presented for the three dimensional cambered wing which was designed to achieve attached supercritical cross flow for lifting conditions typical of supersonic maneuver. The design point was a lift coefficient of 0.4 at Mach 1.62 and 12 deg angle of attack. Results from the nonlinear full potential method are presented to show the validity of the design process along with results from linear theory codes. Longitudinal force and moment data and static pressure data were obtained in the Langley Unitary Plan Wind Tunnel at Mach numbers of 1.58, 1.62, 1.66, 1.70, and 2.00 over an angle of attack range of 0 to 14 deg at a Reynolds number of 2.0 x 10 to the 6th power per foot. Oil flow photographs of the upper surface were obtained at M = 1.62 for alpha approx. = 8, 10, 12, and 14 deg.

Pittman, J. L.↗
DOE OSTI2022

Experimental validation of a high fidelity Monte Carlo neutron transport model of the MIT graphite exponential pile

High-fidelity modeling and simulation were performed for the MIT graphite exponential pile (MGEP) using Monte Carlo neutron transport codes OpenMC and MCNP, and the results were validated by experimental data. The MGEP is being used as the test bed for the design of an autonomous control system for the pile's neutron flux distribution. The main contribution of this work is to generate the training data sets of neutron flux distributions with different locations of control rods that perturb the neutron flux profiles. First, code -to-code cross verification between OpenMC and MCNP was performed to ensure consistency of the numerical modeling within statistical uncertainties. To validate the accuracy of this high-fidelity model, a series of neutron flux measurements were conducted using a Helium-3 (He-3) neutron detector on a mobile platform that is placed inside the pile. Second, the neutron flux profiles were measured in four vertical layers of interest, and compared to the corresponding simulation results. The comparison results shows that the root mean square error is less than 2.5% in the two upper layers, and less than 4.5% in all four measured layers. Here the results validated the accuracy of the modeling and simulation. Finally, the relative change of the neutron flux profiles from moving control rods was analyzed, which identified the layer that has the best sensitivity regarding the control rods movements. Thus, this work identified and provided training data sets of both simulated and experimental neutron flux profiles in the most sensitive layer, paving the path forward to the real-time experimental demonstration of the autonomous control system.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

OC7 Project Phase II: Code Comparison and Experimental Validation of Hydroelastic Effects and Member-Level Loads in Floating Structures

This paper presents results from Phase II of the OC7 project, focusing on hydroelastic modeling and member-level load prediction for a flexible floating offshore structure. Numerical predictions from 11 academic and industrial partners are validated against experimental measurements obtained from a 1:70-scale test of the VolturnUS-S semisubmersible platform. A comprehensive set of verification and validation cases is examined. The results demonstrate that hydrodynamic added mass has a significant impact on predicted elastic natural frequencies. Under regular wave excitation, the numerical models reproduce platform motions and mooring line tensions with good accuracy. Member-level loads are also predicted with reasonable accuracy. Some discrepancies are observed for potential-flow models not accounting for higher-order effects associated with the instantaneous wetted surface.

17 WIND ENERGY↗
DOE OSTI2026

Phase change material-to-refrigerant heat exchangers: Experimental validation and uneven melting analysis

Thermal energy storage (TES) using phase change materials (PCMs) enables load shifting and reduces mismatches between the building's thermal demand and the heat pump (HP) system's thermal capacity. While most TES studies have focused on single-phase heat transfer fluids, PCM-to-refrigerant heat exchangers (PRHX), in which the refrigerant undergoes liquid-vapor phase change, remain largely underexplored. Here, to address this gap, this study systematically investigates a shell-and-tube PRHX operating as the condenser in an HP through experiments and simulations. A two-dimensional enthalpy-based finite-volume PRHX model was developed and validated against experimental data, including refrigerant and PCM temperature profiles, PRHX capacity, and system-level performance. Results show three characteristic stages: Stage I, the condenser temperature rapidly increases with PCM in the solid state absorbing sensible heat; Stage II, stable operation during PCM phase change; and Stage III, performance decline once part of the PCM becomes fully melted. Heat transfer analysis revealed that uneven PCM melting along the condenser length was driven primarily by variations in the refrigerant-side heat transfer coefficient, rather than local approach temperature differences. Further study demonstrated that minimizing refrigerant outlet subcooling led to more uniform PCM melting and extended Stages I and II by up to 89%. This paper provides a validated PRHX model, clarifies the mechanisms of uneven PCM melting, and highlights subcooling control as an effective strategy to improve TES performance in HP systems without requiring secondary loops.

Graphite matrix↗
DOE OSTI2021

A study on computational fluid dynamics modeling of a refrigerated container for COVID-19 vaccine distribution with experimental validation

A key issue with the distribution of vaccines to prevent COVID-19 is the temperature level required during transport, storage, and distribution. Typical refrigerated transport containers can provide a temperature-controlled environment down to -30 °C. However, the Pfizer vaccine must be carefully transported and stored under a lower temperature between -80 °C and -60 °C. One way to provide the required temperature is to pack the vaccine vials into small packages containing dry ice. Dry ice sublimates from a solid to a gas, which limits the allowable transport duration. This can be mitigated by transporting in a -30 °C refrigerated container. Moreover, because the dry ice will sublimate and thereby release CO 2 gas into the transport container, monitoring the CO 2 concentration within the refrigerated container is also essential. In the present work, a 3D computational fluid dynamics model was developed based on a commercially available refrigerated container and validated with experimental data. The airflow, temperature distribution, and CO 2 concentration within the container were obtained from the simulations. The modeling results can provide guidance on preparing experimental setups, thus saving time and lowering cost, and also provide insight into safety precautions needed to avoid hazardous conditions associated with the release of CO 2 during vaccine distribution.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Experimentally validated high-fidelity simulations of a liquid jet in supersonic crossflow

Here, utilizing recent advancements in computational schemes for compressible, multiphase flows, this work features a parametric study of a pure liquid jet in supersonic crossflow that involves simulating the atomization process for four values of momentum-flux ratio. These simulations are validated against experimental results measured with high-speed X-ray imaging, which confirm the accuracy of the numerical approach. Also, the effect of numerical resolution on some flow behavior is investigated, revealing convergence of the jet shape and surface instability wavelength. Analysis of the resulting sprays includes statistical descriptions of the liquid distribution, liquid structures created through breakup, interfacial instabilities, and dominant flow features. As the flowrate increases, the spray penetrates further, it becomes more disperse, and less liquid impacts the wall, but the droplet size distribution changes little. The wavelength of instabilities on the windward side of the jet diverges from measured trends in subsonic crossflows. In a visualization of the time-averaged flow, counter-rotating vortices are observed along the jet core and in the wake, affecting the process of primary atomization and early droplet trajectories.

42 ENGINEERING↗
NASA NTRS2015

System-Level Experimental Validations for Supersonic Commercial Transport Aircraft Entering Service in the 2018-2020 Time Period

This report describes the work conducted under NASA funding for the Boeing N+2 Supersonic Experimental Validation project to experimentally validate the conceptual design of a supersonic airliner feasible for entry into service in the 2018 -to 2020 timeframe (NASA N+2 generation). The primary goal of the project was to develop a low-boom configuration optimized for minimum sonic boom signature (65 to 70 PLdB). This was a very aggressive goal that could be achieved only through integrated multidisciplinary optimization tools validated in relevant ground and, later, flight environments. The project was split into two phases. Phase I of the project covered the detailed aerodynamic design of a low boom airliner as well as the wind tunnel tests to validate that design (ref. 1). This report covers Phase II of the project, which continued the design methodology development of Phase I with a focus on the propulsion integration aspects as well as the testing involved to validate those designs. One of the major airplane configuration features of the Boeing N+2 low boom design was the overwing nacelle. The location of the nacelle allowed for a minimal effect on the boom signature, however, it added a level of difficulty to designing an inlet with acceptable performance in the overwing flow field. Using the Phase I work as the starting point, the goals of the Phase 2 project were to design and verify inlet performance while maintaining a low-boom signature. The Phase II project was successful in meeting all contract objectives. New modular nacelles were built for the larger Performance Model along with a propulsion rig with an electrically-actuated mass flow plug. Two new mounting struts were built for the smaller Boom Model, along with new nacelles. Propulsion integration testing was performed using an instrumented fan face and a mass flow plug, while boom signatures were measured using a wall-mounted pressure rail. A side study of testing in different wind tunnels was completed as a precursor to the selection of the facilities used for validation testing. As facility schedules allowed, the propulsion testing was done at the NASA Glenn Research Center (GRC) 8 x 6-Foot wind tunnel, while boom and force testing was done at the NASA Ames Research Center (ARC) 9 x 7-Foot wind tunnel. During boom testing, a live balance was used for gathering force data. This report is broken down into nine sections. The first technical section (Section 2) covers the general scope of the Phase II activities, goals, a description of the design and testing efforts, and the project plan and schedule. Section 3 covers the details of the propulsion system concepts and design evolution. A series of short tests to evaluate the suitability of different wind tunnels for boom, propulsion, and force testing was also performed under the Phase 2 effort, with the results covered in Section 4. The propulsion integration testing is covered in Section 5 and the boom and force testing in Section 6. CFD comparisons and analyses are included in Section 7. Section 8 includes the conclusions and lessons learned.

Magee, Todd E.↗
DOE OSTI2025

Experimental Validation of a 40kW, 480V Point-to-Point DC Interlinks for Controller-Agnostic, Interoperable Networked Microgrids

This paper presents the experimental validation of point-to-point dc-interlinks for interconnecting two solar-based, laboratory-scale AC microgrids. DC interlinks provide a solution to numerous technical and operational challenges encountered in networked microgrids, including precise power flow control, stable and fast synchronization, enhanced stability, and improved voltage and frequency regulation. By decoupling microgrids through power converters, dc-interlinks enable power exchange among microgrids that can be owned by different entities (such as communities, utilities, or universities) and managed by diverse microgrid controller vendors. This characteristic makes this dc-interlinks a promising solution for networking real-world microgrids. The presented point-to-point dc interlink utilizes two four-quadrant converters: a 40kW 3-phase ac/dc regulating the dc-link voltage to 800V, and a 3-phase dc/ac controlling power flow. These converters, connected via a 20-foot dc cable, interconnect two ac microgrids operating at 480V, each featuring energy storage, photovoltaic generation, and load emulation. Experimental validation employs commercially available off-the-shelf (COTS) converters and real-world data from solar-powered microgrids in Adjuntas, Puerto Rico. To the authors’ knowledge, this work provides the first at-scale experimental validation of dc-interlinks for networked ac microgrids using COTS inverters, demonstrating their practicality and effectiveness in addressing real-world operational challenges.

Ferrari Maglia, Max [ORNL]↗