Search NASA⌕ Search

SEARCH · Search NASA

Results for “FCIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Techno-Economic Case Study: Low-Temperature Conversion Performance Based on Isolated Anatomical Fractions of Corn Stover

This report summarizes analysis conducted to support a case study under the Feedstock-Conversion Interface Consortium (FCIC) focused on techno-economic analysis (TEA) modeling to quantify the yield and cost ramifications for processing isolated anatomical fractions of corn stover through a low-temperature conversion (biochemical pathway) biorefinery. It is hypothesized that different individual anatomical fractions of corn stover vary in composition and recalcitrance, such that processing each fraction on its own e.g. through dedicated campaigns may enable economic benefits relative to processing the whole stover material. To investigate this concept, we worked with FCIC researchers to obtain data on compositional analysis, as well as processing conditions and yields, for conversion of whole corn stover plus three individual anatomical fractions (cobs, husks, and stalks) across key steps of the biorefinery conversion process within FCIC research scope, namely pretreatment and enzymatic hydrolysis. After running the data through the TEA models, fractionated cobs and husks achieved higher fuel yields and lower minimum fuel selling prices than whole corn stover, but stalks fared worse than whole stover on both metrics. The most direct takeaway from this assessment is that a biorefinery would stand to benefit economically from maximizing the use of cob and husk fractions while avoiding or minimizing the use of stalks, though recognizing practical constraints with this approach in maintaining an equivalent processing capacity (fixed at 2,000 dry metric tonne per day in all cases).

09 BIOMASS FUELS↗
DOE OSTI2024

The Feedstock-Conversion Interface Consortium - Understanding and Mitigating the Impacts of Feedstock Variability in Bioconversion Processes

The Feedstock-Conversion Interface Consortium is led by DOE as a collaborative effort among researchers from 9 National Laboratories. The FCIC was formed because biomass feedstock properties are variable and different from other commodities, and empirical approaches to address these issues have been unsuccessful. The FCIC uses first-principles-based science to de-risk biorefinery scale-up and deployment by understanding and mitigating the impacts of feedstock variability on bioenergy conversion processes. In this presentation, we present a brief overview of key FCIC prinicples and recent results.

biomass↗
DOE OSTI2023

Techno-Economic Case Study: Low-Temperature Conversion Performance Based on Isolated Anatomical Fractions of Corn Stover

This report summarizes analysis conducted to support a case study under the Feedstock Conversion Interface Consortium (FCIC) focused on techno-economic analysis (TEA) modeling to quantify the process yield and resulting process cost impacts for processing isolated anatomical fractions of corn stover through a low-temperature conversion (biochemical) pathway. It is hypothesized that different individual anatomical fractions of corn stover vary in both composition and recalcitrance, giving biorefineries options in whether and how to deal with fractionated or whole biomass feedstock. By quantifying the techno-economic impacts of this variability, we provide actionable information for end users to understand tradeoffs in conversion system yields and economics in considering feedstock processing decisions at the biorefinery gate. For this study, we worked with FCIC researchers to obtain data on the compositional analysis and conversion performance of whole corn stover alongside three individual anatomical fractions (cobs, husks, and stalks) across key steps of the biorefinery conversion process within FCIC’s research scope—pretreatment and enzymatic hydrolysis. This TEA screening assessment highlighted biorefinery economic trade-offs observed through this approach. Namely, relative to processing whole stover biomass, two of the three anatomical fractions for which composition/conversion data were available (cobs and husks) demonstrated the ability to achieve higher fuel yields and lower minimum fuel selling prices (MFSPs), while the third fraction (stalks) led to the opposite result, as a composite reflection of compositional differences and process convertibility.

cost impacts↗
DOE OSTI2023

Techno-Economic Case Study: Fermentation Cost Impacts from Selected Critical Material Attributes

This report summarizes analysis conducted to support a case study under the Feedstock-Conversion Interface Consortium (FCIC) focused on techno-economic analysis (TEA) modeling to quantify the economic implications of biomass hydrolysate substrate variability on fermentation performance and resultant biorefinery fuel yields. It is known that fermentation inhibitors or byproducts, as may either come from constituents in the biomass feedstock or imparted through biorefinery processing operations, can detrimentally impact fermentation rates and yields. However, it is often difficult to isolate fermentation impacts to individual components given the complex nature of biomass varying simultaneously in multiple attributes from one lot to another. For this study, we worked with FCIC researchers to obtain data on key fermentation performance metrics, namely productivity rates and conversion yields, across a number of material attribute species previously selected by the researchers as "critical" attributes which may be found in hydrolysate used as microbial carbon sources during fermentation. These data were run through TEA models to estimate resultant impacts on biorefinery economics, reported as minimum fuel selling price (MFSP). Overall, the trends in MFSP closely followed fuel yields, in turn tied to fermentation process yields and selectivity, with minimal economic impact from variations in fermentation productivity.

09 BIOMASS FUELS↗
DOE OSTI2023

Impact of Anatomical Fractionation of Corn Stover on Hammer Mill Throughput and Energy Consumption

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on loss of very wet stover that causes failures in the first stage grinder and that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbohydrate content (minimum total carbohydrate specification), maximum ash content and the delivered feedstock cost impacts of not being able to feed stover that did not meet the total carbohydrate specification to the conversion reactor. Laboratory data on the impacts of moisture content and tissue fraction on throughput and energy consumption in a stage 2 hammer mill were received from FCIC Subtask 5.1: Preprocessing, Corn Stover Preprocessing (Neal Yancey and Sergio Hernandez, INL). Additional air classifier throughput, energy consumption and separation efficiency data were obtained from FCIC Subtask 5.1 (Neal Yancey, INL) for the new air classifier, which has three exit streams (lights, middle and heavies). These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents and particle sizes had not been analyzed in the laboratory at the time of the model runs, we assumed that the ash distributed proportionally with total mass into the lights and heavies in an air classifier having two exit streams (lights and heavies) and that the lights fraction from the air classifier was not removed.

ash content↗
DOE OSTI2023

Particle Scale Impacts on Deconstruction Energy of Pine Residues

The goal of this Case Study was to quantify the impacts of variable moisture and ash on hammer mill throughput and energy consumption and on generation of fines that are not able to be fed to conversion, as compared to a status quo Base Case system. Also considered was convertible carbon content (minimum carbon specification) and maximum ash content and the delivered feedstock cost impacts of not being able to feed residue not meeting both specifications to the conversion reactor. Laboratory data on the impacts of input particle size and moisture content on the exit particle size were received from FCIC Subtask 5.2: Preprocessing, High Temperature Conversion Preprocessing from their single particle impact population balance modeling study (Tiasha Bhattacharjee, INL). Additional throughput and energy consumption data were obtained from FCIC Subtask 5.2 (Jordan Klinger, INL) for the same grinder with a 6 mm screen in place. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Because the ash contents in the separated fines had not been analyzed in the laboratory at the time of the model runs, we chose to assume that the ash distributed proportionally with total mass into the overs and unders in the disk screen following grinding.

energy consumption↗
DOE OSTI2023

Design of an Integrated Solids Handling System to Maximize Syngas Process Reliability (Cooperative Research and Development Final Report)

The National Renewable Energy Laboratory (NREL), in partnership with Wonderful Renewable Energy (WRE) and Idaho National Laboratory (INL), plans to develop a general methodology for designing integrated biorefinery solids preprocessing, handling, and feeding systems based on the chemical, physical, and mechanical attributes of the starting biomass material. This attribute-driven approach will include detailed feedstock property measurements, iterative computational modeling, and bench-scale testing to design systems for preprocessing, handling, and reactor in-feed, up to and including the selection of the conversion reactor. The initial tests and system design will be conducted using waste material from almond and pistachio growing and production operations (shells, hulls, and wood), targeting the conversion of this material to syngas for electricity production. The methodology will then be generalized to other feedstocks. The purpose of this project is to design an integrated solids handling system to maximize the process reliability of converting almond and pistachio waste to electricity. The design methodology and workflow developed from this example will then be applied to the Feedstock Conversion Interface Consortium (FCIC) benchmark loblolly pine residues, thus demonstrating the robustness of the overall design approach and providing insight and guidance for future conversion systems. V-Grid Energy Systems was brought on as a subcontractor to provide gasifiers and labor to complete gasifier runs.

09 BIOMASS FUELS↗
DOE OSTI2023

Failure Mode and Effects Analysis Summary Report

This report provides an overview of the development of failure modes and effects analysis (FMEA) and its implementation as a systematic criticality and risk assessment tool supporting a quality by design (QbD) approach for FCIC research. This report also provides a high-level overview of the results for the FMEA evaluation of two feedstock preprocessing system configurations: (1) generation of pine residue materials for high-temperature pyrolysis conversion and (2) generation of corn stover materials for low-temperature conversion using deacetylation and disc mechanical refining pretreatment for fermentation to hydrocarbons. For the results presented in this report, our FMEA interviews included two approaches. The first approach was to perform FMEA interviews for the entire system of unit operations giving a wholistic system level view. The second approach consisted of detailed interviews for each individual unit operation within the system allowing for a “deep dive” into the specific failures for the individual components within the configuration. These two approaches provide different resolutions of information. The FMEA results of this report were focused on failures associated with meeting critical quality attributes (CQAs) identified for the target conversion processes for each processed feedstock type. The information gathered through the FMEA interviews include estimations of risk scores for meeting each given CQA specification, identification of the impacts for not meeting a CQA specification, capturing causes associated with material attributes and process parameters for each failure, identification of current detection methods, and speculation of potential mitigation strategies for decreasing a failure’s risk score. The complete results of all FMEA interviews are provided in the Appendices of this report.

conversion↗
DOE OSTI2023

Air Classification of Forest Residue for Tissue and Ash Separation Efficiency

The goal of this Case Study was to evaluate the performance of air classification of logging residues toward meeting conversion CMAs for carbon and ash contents, as compared to the static status quo Base Case system in which the residues are first dried and then ground in a hammer mill with a 6 mm screen and fines less than 1.18 mm are removed. Also considered were moisture and ash impacts on throughput and Overall Operating Effectiveness (OOE), as well as delivered feedstock cost and minimum fuel selling price (MFSP). Laboratory data on the impacts of fan speed and moisture content on the separation efficiency of soil ash, needles and bark from white wood were received from FCIC Subtask 5.2: Preprocessing, High Temperature Conversion Preprocessing (Jordan Klinger and Tiasha Bhattacharjee, INL). Average throughput and energy consumption data were obtained from the Bioenergy Feedstock National User Facility (BFNUF) (Neal Yancey, INL) for the same air classifier. These data were utilized to develop the necessary response surface equations to perform throughput analysis using discrete event simulation. Feedstock-Conversion Interface Consortium. Because the Base Case status quo system utilizes drying prior to grinding, we modeled the Case Study with drying prior to air classification and subsequent grinding of the separated white wood to isolate the individual quality and cost impacts of air classification relative to the Base Case system.

CMA↗
DOE OSTI2023

Failure Modes and Effects Analysis of Biorefinery Pathways

This talk provides an overview of failure modes and effects analysis (FMEA) development and implementation as a systematic criticality and risk assessment tool for biorefinery pathways within the FCIC. This supports a quality by design (QbD) approach, and this talk provides a high-level overview of the results for the FMEA evaluation focused on the generation of pine residue materials for high-temperature pyrolysis conversion. the FMEA interviews included two approaches. The first approach was based around the entire system of unit operations giving a wholistic system level view. The second approach used detailed interviews from individual unit operation within the system allowing for specific failures for individual system components. These two approaches provide different resolutions of information about the reliability and risk. The FMEA results focused on failures associated with meeting critical quality attributes (CQAs) identified for the high temperature conversion of loblolly pine residues and were supplemented with experimental data supporting process upsets and reliability also collected within the consortium. Estimations of risk scores for meeting each given CQA specification, identification of the impacts for not meeting a CQA specification, capturing causes associated with material attributes and process parameters for each failure, identification of current detection methods, and speculation of potential mitigation strategies for decreasing a failure’s risk score were gathered through the FMEA interviews, and were combined to understand the overall process risk metrics and where technology, process, and knowledge improvements are needed in order to de-risk emerging biorefineries.

09 BIOMASS FUELS↗