Search NASA⌕ Search

SEARCH · Search NASA

Results for “FERMI LEVEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Detecting Fermi-level shifts by Auger electron spectroscopy in Si and GaAs

In this paper, changes in surface Fermi-level of Si and GaAs, caused by doping and cleaning, are investigated by Auger electron spectroscopy. Based on the Auger voltage contrast, we compared the Auger transition peak energy but with higher accuracy by using a more accurate detector and an improved peak position determination method. For silicon, a peak shift as large as 0.46 eV was detected when comparing a cleaned p-type and n-type wafer, which corresponds rather well with the theoretical difference in Fermi-level. If no cleaning was applied, the peak position did not differ significantly for both wafer types, indicating Fermi-level pinning in the band gap. For GaAs, peak shifts were detected after cleaning with HF and (NH4)2S-solutions in an inert atmosphere (N2-gas). Although the (NH4)2S-cleaning in N2 is very efficient in removing the oxygen from the surface, the observed Ga- and As-peak shifts are smaller than those obtained after the HF-cleaning. It is shown that the magnitude of the shift is related to the surface composition. After Si-deposition on the (NH4)2S-cleaned surface, the Fermi-level shifts back to a similar position as observed for an as-received wafer, indicating that this combination is not successful in unpinning the Fermi-level of GaAs. This work has been funded by J.D.'s PhD fellowship of the Fund of Scientific Research-Flanders (FWO-V) (Dossier No. 11U4516N). P.H. acknowledges support from Becas Chile-CONICYT. This research was also supported by the FWO Odysseus Program, the Belgian Hercules Stichting with the Project No. Her/08/25 and AKUL/13/19 and the KU Leuven project GOA "Fundamental challenges in Semiconductor Research". The authors would also like to thank Bastiaan Opperdoes and Ludwig Henderix for technical support. The work was supported by the U.S. Department of Energy (USDOE), Office of Science, Office of Basic Energy Sciences, Division of Materials Sciences and Engineering, and performed in the Environmental Molecular Sciences Laboratory, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory (PNNL). Battelle operates PNNL for the USDOE under contract DE-AC05-76RL01830.

Environmental Molecular Sciences Laboratory↗

Observation of an electron band above the Fermi level in FeTe{sub 0.55}Se{sub 0.45} from in-situ surface doping

We used in-situ potassium (K) evaporation to dope the surface of the iron-based superconductor FeTe{sub 0.55}Se{sub 0.45}. The systematic study of the bands near the Fermi level confirms that electrons are doped into the system, allowing us to tune the Fermi level of this material and to access otherwise unoccupied electronic states. In particular, we observe an electron band located above the Fermi level before doping that shares similarities with a small three-dimensional pocket observed in the cousin, heavily electron-doped KFe{sub 2−x}Se{sub 2} compound.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quasi-Fermi level splitting and sub-bandgap absorptivity from semiconductor photoluminescence

A unified model for the direct gap absorption coefficient (band-edge and sub-bandgap) is developed that encompasses the functional forms of the Urbach, Thomas-Fermi, screened Thomas-Fermi, and Franz-Keldysh models of sub-bandgap absorption as specific cases. We combine this model of absorption with an occupation-corrected non-equilibrium Planck law for the spontaneous emission of photons to yield a model of photoluminescence (PL) with broad applicability to band-band photoluminescence from intrinsic, heavily doped, and strongly compensated semiconductors. The utility of the model is that it is amenable to full-spectrum fitting of absolute intensity PL data and yields: (1) the quasi-Fermi level splitting, (2) the local lattice temperature, (3) the direct bandgap, (4) the functional form of the sub-bandgap absorption, and (5) the energy broadening parameter (Urbach energy, magnitude of potential fluctuations, etc.). The accuracy of the model is demonstrated by fitting the room temperature PL spectrum of GaAs. It is then applied to Cu(In,Ga)(S,Se){sub 2} (CIGSSe) and Cu{sub 2}ZnSn(S,Se){sub 4} (CZTSSe) to reveal the nature of their tail states. For GaAs, the model fit is excellent, and fitted parameters match literature values for the bandgap (1.42 eV), functional form of the sub-bandgap states (purely Urbach in nature), and energy broadening parameter (Urbach energy of 9.4 meV). For CIGSSe and CZTSSe, the model fits yield quasi-Fermi leveling splittings that match well with the open circuit voltages measured on devices made from the same materials and bandgaps that match well with those extracted from EQE measurements on the devices. The power of the exponential decay of the absorption coefficient into the bandgap is found to be in the range of 1.2 to 1.6, suggesting that tunneling in the presence of local electrostatic potential fluctuations is a dominant factor contributing to the sub-bandgap absorption by either purely electrostatic (screened Thomas-Fermi) or a photon-assisted tunneling mechanism (Franz-Keldysh). A Gaussian distribution of bandgaps (local E{sub g} fluctuation) is found to be inconsistent with the data. The sub-bandgap absorption of the CZTSSe absorber is found to be larger than that for CIGSSe for materials that yield roughly equivalent photovoltaic devices (8% efficient). Further, it is shown that fitting only portions of the PL spectrum (e.g., low energy for energy broadening parameter and high energy for quasi-Fermi level splitting) may lead to significant errors for materials with substantial sub-bandgap absorption and emission.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Reduction of Fermi level pinning and recombination at polycrystalline CdTe surfaces by laser irradiation

Laser processing of polycrystalline CdTe is a promising approach that could potentially increase module manufacturing throughput while reducing capital expenditure costs. For these benefits to be realized, the basic effects of laser irradiation on CdTe must be ascertained. In this study, we utilize surface photovoltage spectroscopy (SPS) to investigate the changes to the electronic properties of the surface of polycrystalline CdTe solar cell stacks induced by continuous-wave laser annealing. The experimental data explained within a model consisting of two space charge regions, one at the CdTe/air interface and one at the CdTe/CdS junction, are used to interpret our SPS results. The frequency dependence and phase spectra of the SPS signal are also discussed. To support the SPS findings, low-temperature spectrally-resolved photoluminescence and time-resolved photoluminescence were also measured. The data show that a modest laser treatment of 250 W/cm{sup 2} with a dwell time of 20 s is sufficient to reduce the effects of Fermi level pinning at the surface due to surface defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Transparent Conducting Oxides for Photovoltaics: Manipulation of Fermi Level, Work Function and Energy Band Alignment

Doping limits, band gaps, work functions and energy band alignments of undoped and donor-doped transparent conducting oxides ZnO, In{sub 2}O{sub 3}, and SnO{sub 2} as accessed by X-ray and ultraviolet photoelectron spectroscopy (XPS/UPS) are summarized and compared. The presented collection provides an extensive data set of technologically relevant electronic properties of photovoltaic transparent electrode materials and illustrates how these relate to the underlying defect chemistry, the dependence of surface dipoles on crystallographic orientation and/or surface termination, and Fermi level pinning.

14 SOLAR ENERGY↗

Enhancement of Thermoelectric Performance for n-Type PbS through Synergy of Gap State and Fermi Level Pinning

In this paper, we report that Ga-doped and Ga-In-codoped n-type PbS samples show excellent thermoelectric performance in the intermediate temperature range. First-principles electronic structure calculations reveal that Ga doping can cause Fermi level pinning in PbS by introducing a gap state between the conduction and valence bands. Furthermore, Ga-In codoping introduces an extra conduction band. These added electronic features lead to high electron mobilities up to μH ~ 630 cm 2 V -1 s -1 for n of 1.67 × 10 19 cm -3 and significantly enhanced Seebeck coefficients in PbS. Consequently, we obtained a maximum power factor of ~32 μW cm -1 K -2 at 300 K for Pb 0.9875 Ga 0.0125 S, which is the highest reported for PbS-based systems giving a room-temperature figure of merit, ZT, of ~0.35 and ~0.82 at 923 K. For the codoped Pb 0.9865 Ga 0.0125 In 0.001 S, the maximum ZT rises to ~1.0 at 923 K and achieves a record-high average ZT (ZT avg ) of ~0.74 in the temperature range of 400-923 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Realizing tunable Fermi level in SnTe by defect control

The tuning of the Fermi level in tin telluride, a topological crystalline insulator, is essential for accessing its unique surface states and optimizing its electronic properties for applications such as spintronics and quantum computing. In this study, we demonstrate that the Fermi level in tin telluride can be effectively modulated by controlling the tin concentration during chemical vapor deposition synthesis. By introducing tin-rich conditions, we observed a blue shift in the x-ray photoelectron spectroscopy core-level peaks of both tin and tellurium, indicating an upward shift in the Fermi level. Further, this shift is corroborated by a decrease in work function values measured via ultraviolet photoelectron spectroscopy, confirming the suppression of Sn vacancies. Our findings provide a low-cost, scalable method to achieve tunable Fermi levels in tin telluride, offering a significant advancement in the development of materials with tailored electronic properties for next-generation technological applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Precise Fermi level engineering in a topological Weyl semimetal via fast ion implantation

The precise controllability of the Fermi level is a critical aspect of quantum materials. For topological Weyl semimetals, there is a pressing need to fine-tune the Fermi level to the Weyl nodes and unlock exotic electronic and optoelectronic effects associated with the divergent Berry curvature. However, in contrast to two-dimensional materials, where the Fermi level can be controlled through various techniques, the situation for bulk crystals beyond laborious chemical doping poses significant challenges. Here, we report the milli-electron-volt (meV) level ultra-fine-tuning of the Fermi level of bulk topological Weyl semimetal tantalum phosphide using accelerator-based high-energy hydrogen implantation and theory-driven planning. By calculating the desired carrier density and controlling the accelerator profiles, the Fermi level can be experimentally fine-tuned from 5 meV below, to 3.8 meV below, to 3.2 meV above the Weyl nodes. High-resolution transmission electron microscopy reveals the crystalline structure is largely maintained under irradiation, while electrical transport indicates that Weyl nodes are preserved and carrier mobility is also largely retained. Our work demonstrates the viability of this generic approach to tune the Fermi level in semimetal systems and could serve to achieve property fine-tuning for other bulk quantum materials with ultrahigh precision.

36 MATERIALS SCIENCE↗

Control of passivation and compensation in Mg-doped GaN by defect quasi Fermi level control

A defect quasi Fermi level (dQFL) control process based on above bandgap illumination was applied to control H and V N -complexes, which are the main contributors to the passivation and self-compensation, respectively, in Mg:GaN grown via metalorganic chemical vapor deposition. Secondary ion mass spectrometry measurements confirmed that the total Mg incorporation was unaffected by the process. However, the total H concentration was reduced to similar levels obtained by post-growth thermal activation prior to any annealing treatment. Similarly, the 2.8 eV emission in the photoluminescence spectra, attributed to compensating V N and its complexes, was reduced for the dQFL-process samples. After thermal activation and Ni/Au contact deposition, Hall effect measurements revealed lower resistivities (increased mobilities and free hole concentrations) for dQFL-grown samples with Mg doping concentrations above and below 2 × 10 19 cm -3 . All these results demonstrate that the dQFL process can effectively reduce the H-passivation and self-compensation of the Mg:GaN films.

36 MATERIALS SCIENCE↗

Fermi level pinning at the Ge(001) surface—A case for non-standard explanation

To explore the origin of the Fermi level pinning in germanium, we investigate the Ge(001) and Ge(001):H surfaces. The absence of relevant surface states in the case of Ge(001):H should unpin the surface Fermi level. This is not observed. For samples with donors as majority dopants, the surface Fermi level appears close to the top of the valence band regardless of the surface structure. Surprisingly, for the passivated surface, it is located below the top of the valence band allowing scanning tunneling microscopy imaging within the band gap. We argue that the well known electronic mechanism behind band bending does not apply and a more complicated scenario involving ionic degrees of freedom is therefore necessary. Experimental techniques involve four point probe electric current measurements, scanning tunneling microscopy, and spectroscopy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Buried Interfaces in Organic Photocathodes for H 2 Evolution: Fermi-Level Pinning and Recombination

Herein, we demonstrate how Fermi-level pinning at buried contacts impacts solar fuel generation in all-polymer photocathodes by systematically comparing the effects of work function, hydroxyl coverage, and hydrogen evolution using chemically modified indium tin oxide (ITO) supports. Photovoltages and net photocathode performance are improved when the ITO is passivated using phosphonic acids, independent of work function, suggesting that the passivation reduces Fermi-level pinning at the buried interface arising from blended heterojunction interactions with surface metal hydroxyls. Transient photovoltage decay reveals differences in recombination mechanisms, supported by light intensity-dependent measurements. Briefly, nonpassivated, hydrophilic contacts exhibit trap-assisted recombination, while passivated, hydrophobic contacts follow bimolecular recombination. We then investigate changes in electroactivity of hole-transfer processes as a function of scan rate and repetitive cycling using a diffusion-controlled molecular redox probe, analogous to a hole-only device achieved via the electrolyte. The nonpassivated buried contacts exhibit higher overpotentials for oxidation, indicative of hole injection/extraction barriers. We observe irreversible electron transfer via the hole-transport level of the blended heterojunction and a strong cycle dependence, consistent with changes in the hole trap state density. Passivation results in more reversible redox behaviors, consistent with more Ohmic-like contacts. Collectively, these results provide context toward the realization of durable organic photoelectrodes with optimized photovoltages and net solar-to-hydrogen conversion efficiencies via fundamental understanding of the rates of carrier generation, recombination, and transport in high-dielectric aqueous environments and opportunities to characterize buried interfaces under device-relevant electric fields.

buried interfaces↗

Determination of the Fermi level position in dilute magnetic Ga{sub 1-x}Mn{sub x}N films

We report on a combined theoretical and experimental determination of the Fermi level position in wurtzite Ga{sub 1−x}Mn{sub x}N films with x=4% and x=10% as grown by molecular beam epitaxy. By means of ellipsometric measurements, the real part of the frequency-dependent conductivity is determined. An electronic model in the framework of the effective bond-orbital model is parameterized in order to theoretically reproduce the measured transport properties. Predictions for the long-wavelength behaviour as a function of the Fermi level are made. The corresponding density of states obtained in this model is in qualitative agreement with first-principle calculations. The absence of a significant experimental peak in the AC conductivity for small frequencies indicates that the Fermi level lies in a gap between two Mn-related impurity bands in the host band gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanism of charge transfer and its impacts on Fermi-level pinning for gas molecules adsorbed on monolayer WS{sub 2}

Density functional theory calculations were performed to assess changes in the geometric and electronic structures of monolayer WS{sub 2} upon adsorption of various gas molecules (H{sub 2}, O{sub 2}, H{sub 2}O, NH{sub 3}, NO, NO{sub 2}, and CO). The most stable configuration of the adsorbed molecules, the adsorption energy, and the degree of charge transfer between adsorbate and substrate were determined. All evaluated molecules were physisorbed on monolayer WS{sub 2} with a low degree of charge transfer and accept charge from the monolayer, except for NH{sub 3}, which is a charge donor. Band structure calculations showed that the valence and conduction bands of monolayer WS{sub 2} are not significantly altered upon adsorption of H{sub 2}, H{sub 2}O, NH{sub 3}, and CO, whereas the lowest unoccupied molecular orbitals of O{sub 2}, NO, and NO{sub 2} are pinned around the Fermi-level when these molecules are adsorbed on monolayer WS{sub 2}. The phenomenon of Fermi-level pinning was discussed in light of the traditional and orbital mixing charge transfer theories. The impacts of the charge transfer mechanism on Fermi-level pinning were confirmed for the gas molecules adsorbed on monolayer WS{sub 2}. The proposed mechanism governing Fermi-level pinning is applicable to the systems of adsorbates on recently developed two-dimensional materials, such as graphene and transition metal dichalcogenides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Tuning the Dirac point to the Fermi level in the ternary topological insulator (Bi{sub 1−x}Sb{sub x}){sub 2}Te{sub 3}

In order to stabilize Majorana excitations within vortices of proximity induced topological superconductors, it is mandatory that the Dirac point matches the Fermi level rather exactly, such that the conventionally confined states within the vortex are well separated from the Majorana-type excitation. Here, we show by angle resolved photoelectron spectroscopy that (Bi{sub 1−x}Sb{sub x}){sub 2}Te{sub 3} thin films with x = 0.94 prepared by molecular beam epitaxy and transferred in ultrahigh vacuum from the molecular beam epitaxy system to the photoemission setup match this condition. The Dirac point is within 10 meV around the Fermi level, and we do not observe any bulk bands intersecting the Fermi level.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Redox Couples Control Band Bending, Photovoltage, and Quasi-Fermi Levels in Tungsten Oxide (WO 3 ) Photoanodes

Tungsten oxide (WO 3 ) is a well-known photoanode and photocatalyst for photoelectrochemical (PEC) water oxidation. Because the compound has a deep valence band, it can facilitate the oxygen evolution reaction without added cocatalysts, and it can drive the oxidation of species with much higher electrochemical potentials, including the conversion of water to hydrogen peroxide, sulfate to persulfate, and iodate to meta-periodate. Here, we use the liquid vibrating Kelvin probe surface photovoltage (liquid VK-SPV) technique in combination with open circuit potential (OCP) and photoelectrochemical (PEC) scans to assess the possibility of reaching such oxidizing potentials in aqueous electrolytes and at open circuit. Here, this is done by mapping the quasi-Fermi levels of electrons and holes at the interfaces as a function of the light intensity. Nanostructured WO 3 photoelectrodes for this purpose were fabricated by thermal annealing of a tungstic acid solution on fluorine-doped tin oxide. Electrochemical measurements are conducted at open circuit and 400 nm LED light illumination in electrolytes containing fast (O 2 /H 2 O 2 ), slow (O 2 /H 2 O), and very oxidizing (NaIO 4 /NaIO 3 ) redox couples. Photovoltage values scale with the light intensity and with the built-in potential for each redox couple and reach values up to 0.61 V under 20 mW cm –2 illumination for the NaIO 4 electrolyte. This shows that the photoelectrodes behave like Schottky-type diodes whose maximum possible energy output is determined mainly by the built-in voltage of each junction. For slow redox couples, the quasi-Fermi level of the holes increases with light intensity due to hole accumulation at the WO 3 –liquid interface. For example, for the O 2 /H 2 O electrolyte, interfacial hole accumulation and removal occur on the 90–300 s time scale. For the fast hole acceptor H 2 O 2 , on the other hand, the quasi-Fermi level of the photoholes is pinned to the electrochemical potential of the O 2 /H 2 O 2 couple. This limits the energy conversion efficiency of the electrode. Overall, these results reveal the influence of charge transfer thermodynamics and kinetics on the photovoltage of WO 3 . Furthermore, the work further establishes VK-SPV as a contactless method to observe the photovoltage, carrier dynamics, and quasi-Fermi levels of semiconductor-liquid junctions.

Electrodes↗