Ferrocene and ferrocene derivatives
Annotated bibliography of ferrocene and derivatives including synthesis, reaction, bonding, and application
FERROCENE↗
SEARCH · Search NASA
Results for “FERROCENE”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Preliminary Appraisal of Ferrocene as an Igniting Agent for JP-4 Fuel and Fuming Nitric Acid
A preliminary experimental study was made of the properties of ferrocene as a solute and as a suspension in JP-4 fuel, and of the ignition delays of ferrocene - JP-4 mixture with A.F. specification 14104 white fuming nitric acid (WFNA). The investigation covered concentrations of 4 to 10 percent by weight ferrocene, and a temperature range of -40 to 80 F. The solubility of ferrocene in JP-4 is about 5 percent at room temperature and about 1 percent (extrapolated) at -80 F. The solubility is increased somewhat by increased aromatics content. Undissolved ferrocene particles of 100 mesh and smaller settle rapidly in JP-4. Clear solutions of 4 and 5 percent ferrocene in JP-4 fuels containing 10 and 25 percent by volume aromatics, respectively, do not ignite with WFNA at room temperature. Mixtures containing 10 percent ferrocene (100- mesh and smaller undissolved particles in suspension) ignited with vigorous persistent flames at room temperature, but did not ignite at -38 F. The ignition delays at room temperature, however, were widely varied; the range from 85 milliseconds to over 1 second perhaps reflected differences in degree of sedimentation.
Miller, RIley O.↗
Correlation of Spectral and Electrochemical Properties of a Series of Ferrocene Derivatives
Charge-transfer-to-solvent (CTTS) bands are observed in the UV/VIS spectra of a series of ferrocene derivatives (ferrocene; 1,1’-dimethyl; 1,2,3,4,5-pentamethyl; 1,2,3,4,l’,2’,3’,4’-octamethyl; and decamethyl) by the addition of increasing amounts of CCl4 to ethanol solutions. A linear correlation (slope = 8540 per cm/V) was found between the redox potential and the energy of the CTTS band, consistent with electrochemical and photochemical oxidation by removal of an electron from the same molecular orbital. Inclusion of literature data for ruthenocene and [(η^(5)-C5H5)Fe(CO)]4 results in a line with a slope of 8140 per cm/V, within 1 percent of the wavenumber to electron volt conversion factor. Calculation of association constants (K) shows a slight decrease (1.2 to 0.7 per mole fraction) as the bulkiness of the cyclopentadienyl ring increases, consistent with either a steric or a repulsive electronic effect. The extinction coefficient of the CTTS absorption was constant at approximately 1700 per Mcm .
ultraviolet spectroscopy↗
Experiments with ferrocene
Acetylferrocene preparation by reacting ferrocene with acetic anhydride in phosphoric acid and reducing acetylferrocene to alpha-hydroxyethyl ferrocene by potassium borohydride in methanol
Mcmanus, S. P.↗
Ferrocene Containing Copolymers with Improved Electrostatic Dissipation Properties for Advanced Applications
Electrostatic dissipative polymers are used for a variety of functions. Typical methods utilized to transform electrically insulating polymers into either charge dissipative or conductive materials involve incorporating a conductive filler, conductive polymer, oxidizing the surface using plasma, or incorporating surfactants that act as surface wetting agents. Another approach is to synthesize a block copolymer that is expected to result in better electrical properties with minimal impacts to physical, fire, and thermal properties. One such block that can be added into the main chain of polymers is a diol terminated ferrocene oligomer, which is expected to impart electrostatic dissipative properties into the host polymer while concurrently improving the overall fire properties. Previous work with polyurethanes incorporating a ferrocene oligomer into the main chain resulted in much improved fire retardancy. In dealing with electrostatic dissipative materials the important questions are: how easily does the material charge and how quickly can the charge move to ground. One normally describes the materials conductivity, but conductivity only measures the fastest path for an electron not the slowest path. The slowest path is the one of interest, since it is left on the surface and thus can cause discharges. In order to assess ease of charging and decay times corona charge dissipation measurements can accurately assess these properties by introducing a charge on the surface of the material then measuring the surface voltage and the amount of charge deposited. The charge decay curve then will give an indication of a materials electrostatic dissipation properties. Normally, triboelectric testing can be performed, but results vary. Corona charge dissipation results are more repeatable.
Smith, T. M.↗
Synthesis of ferrocene-nitrogen-containing polymers with conjugated bonds
Synthesis of ferrocene-nitrogen-containing polymers with conjugated bonds
CONJUGATED SYSTEM↗
Electrocatalytic Ammonia Oxidation by Pyridyl-Substituted Ferrocenes
Ammonia (NH 3 ) is a promising carbon-free fuel when prepared from sustainable resources. First-row transition metal electrocatalysts for ammonia oxidation are an enabling technology for sustainable energy production. We describe electrocatalytic ammonia oxidation using robust molecular complexes based on Earth-abundant iron. Electrochemical studies of ferrocenes with covalently attached pyridine arms reveal facile ammonia oxidation in DMSO (2.4 M NH 3 ) with modest overpotentials (η = 770–820 mV) and turnover frequencies (125–560 h –1 ). Experimental and computational studies indicate that the pendant pyridyl base serves as an H-bond acceptor with an N–H bond of ammonia that transfers a proton to the pyridine following oxidation by the attached ferrocenium moiety in a proton-coupled electron transfer (PCET) step. This generates an amidyl (•NH 2 ) radical stabilized via H-bonding to a pendant pyridinium moiety that rapidly dimerizes to hydrazine (H 2 N–NH 2 ), which is easily oxidized to nitrogen (N 2 ) at the glassy carbon working electrode. This report identifies a general strategy to oxidize ammonia via H-bonding to a base (B:), thereby activating [B···H-NH 2 ] toward PCET by a proximal oxidant to form [BH···NH 2 ] +/• radical cations, which are susceptible to dimerization to form easily oxidized hydrazine.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
High-Spin State of a Ferrocene Electron Donor Revealed by Optical and X-ray Transient Absorption Spectroscopy
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Decoding Antenna Behavior in Metal—Organic Frameworks
Metal–organic frameworks (MOFs) define a solid-state platform for developing artificial photosystems. Efficient anisotropic exciton migrations in these frameworks entail “antenna behavior” that can power up the distal interior reaction centers (RC), driving charge separation between donor-acceptor pairs. Reminiscent of the natural light-harvesting complex, such processes can achieve high quantum yield by exploiting the vast interior surface of the porous crystallites. It is important to understand the optimum positioning of the RC site relative to the anisotropic exciton migration path within these frameworks. The efficiency of such antenna behavior is probed here through Stern–Volmer (SV) type analysis with a series of node-anchored redox quenchers, ferrocene-carboxylate, ferrocene acetate, and dinitrobenzoate. Decoding various intrinsic processes, this work constructs a revised SV formalism in solid assembly that hosts ultrafast anisotropic exciton migration to account for the intrinsic exciton hopping rate from the extrinsic electron transfer rate, and the dimension of effective quenching. In conclusion, this transformative understanding can be applied to other relevant solid-state assemblies.
Saha, Bapan [Southern Illinois University, Carbond↗
Diazonium-Functionalized Silicon Hybrid Photoelectrodes: Film Thickness and Composition Effects on Photoelectrochemical Behavior
Aryl diazonium electrografting is a powerful method for imparting molecular functionality onto various substrates by forming a stable carbon-surface covalent bond. While the high reactivity of the aryl radical intermediate makes this method fast and reliable, it can also lead to the formation of an insulating and disordered multilayer film. These thick films affect electrochemical performance, especially for semiconductor substrates used in photoelectrochemical applications. For this work we studied the effects of film thickness and composition by electrografting in situ-generated aminobenzene diazonium salts onto both n-type and p-type silicon electrodes at fixed potentials. Next, we attached ferrocene to the amine-terminated films and probed their (photo)electrochemical behavior. Cyclic voltammetry measurements showed decreased electrochemical reversibility with increasing diazonium film thickness; this reversibility was restored when ferrocene was incorporated throughout the film with a layer-by-layer deposition process. Finally, we compared the behavior of dark p-type electrodes to n-type photoelectrodes and observed differences in the electrochemical reversibility that we attribute to the change in potential drop across the two interfaces.
charge transfer↗
Photosynthesis of CO from CO 2 with an iron polypyridyl catalyst at a passivated silicon photoelectrode
A first-row transition metal catalyst, [Fe(tpy)(Mebim-py)(NCCH 3 )] 2+ (tpy = 2,2′:6′,2′′-terpyridine, Mebim-py = 1-methylbenzimidazol-2-ylidene-3-(2′-pyridine)) mediates CO 2 reduction to CO at passivated p-Si photoelectrodes with applied potentials 240 mV positive of the standard CO 2 /CO reduction potential. The molecular catalyst's selectivity for CO was retained under photoelectrochemical conditions, with negligible direct proton reduction promoted by the photoelectrode. The faradaic efficiency for CO (44 ± 6%) was slightly enhanced relative to the catalyst performance in the dark (33%). A photosynthetic cell based on this photocathode system, coupled with ferrocene oxidation at the anode, successfully operated at a cell voltage of −1.2 V. The photovoltage generated by illumination of p-Si–CH 3 met and surpassed the potential required for CO 2 reduction when coupled with ferrocene oxidation. By leveraging a low-overpotential CO 2 reduction electrocatalyst, a photo-assisted electrochemical efficiency of 0.15% and applied bias photon-to-current efficiency of 0.05% was achieved for this single-junction cell, ultimately storing 46 kJ mol −1 (11 kcal mol −1 ) of photon energy.
Carbon Dioxide Reduction↗
Correlation Between Microscopic Current Fluctuations Observed at Ultra-Microelectrodes and Macroscopic Bulk Electrolysis Performance in Redox-Active Microemulsions
Microemulsions (μEs) have been proposed as redox flow battery (RFB) electrolytes that maximize ionic conductivity and charge capacity by synergizing two immiscible phases. However, charge transfer during electrolysis in μEs is poorly understood. Here, we show that ultramicroelectrode electrolysis of ferrocene-loaded μEs –20%, 60%, and 90% water - reveals stochastic current fluctuations. These are differentiated in the scanning electrochemical microscopy (SECM) geometry, where power spectral density analysis showed distinct changes in the frequency contributions. SECM in the substrate generation-tip collection mode showed that fluctuations arise under mass-transfer control. Significant differences in the diffusion coefficient of ferrocene species were deducted from SECM approach curves, suggesting phase transfer behavior. Using bulk electrolysis, we calculated the charge accessibility and cycling behavior in the μEs. A decrease in the stochastic behavior of the μEs seems to correlate to a higher accessibility and cycling performance, with the 90% water μE displaying the best reversibility and the 60% the lowest. Altogether, these results suggest that Marangoni-type convection driven by concentration gradients and/or μE restructuring during charge transfer play a role in the electrochemical performance of μEs. This presents opportunities for screening and diagnosing the performance of these emerging RFB electrolytes.
25 ENERGY STORAGE↗
Structuring, stochastic behavior, and charge storage capacity of redox-active microemulsions formulated with mixtures of toluene and ionic liquid as oil phase
Oil/water microemulsions (µEs) are promising electrolytes for redox flow batteries (RFBs) as they simultaneously improve charge capacity and ionic conductivity. Here, we report the successful formulation of bicontinuous µEs where the oil phase is a solution of trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)amide ionic liquid in toluene with redox-active ferrocene. We examined the effect of supporting electrolyte anion (NO 3 – , Cl – , ClO 4 – ) on the structure, reactivity, transport, and electrolytic performance of redox-active µEs. Neutron scattering and nuclear magnetic resonance showed that the domain size increased as Cl – > NO 3 – > ClO 4 – while the ferrocene diffusion coefficient increased as NO 3 – > Cl – > ClO 4 – . Scanning electrochemical microscopy indicated anion-dependent current fluctuations during electrolysis, with ClO 4 – exhibiting the least high-frequency oscillations, which correlate to the highest charge and discharge capacity and reversibility. All ionic liquid containing systems improved the performance of toluene-based µEs, highlighting new design principles for these electrolytes.
diffusion↗
A study of solid-propellant vaporization and diffusion processes Final technical report
Vaporization rate and diffusion coefficient determined for organic additives to polyurethane solid propellants - dioctyl adipate and ferrocene
SOLID PROPELLANT↗
Coupling Interfacial Redox‐Reactions with In Situ Proton Generation for the Photoelectrochemical Separation of Rare‐Earth Elements
Abstract A dual‐function photoelectrochemical (PEC) separation system is demonstrated for rare‐earth element (REE) recovery. The sustainable release of the captured REEs is promoted through the synergistic integration of a redox‐reaction for electrostatic repulsion, and in situ proton generation for ion‐exchange, all driven by photoelectrochemistry. The platform consists of a redox‐copolymer, poly(ferrocenylpropyl methacrylamide‐ co ‐methacrylic acid) (P(FPMAm‐ co ‐MAA)) (PFM), conjugated with carbon nanotubes (CNTs) and coated onto titanium dioxide nanorods (TNRs). The (PFM‐CNT)/TNR spontaneously adsorbs up to 214.2 mg of Yttrium/g PFM by ion‐exchange, and demonstrates broad applicability for other REEs. The adsorbed REEs are released through the PEC oxidation of ferrocene (Fc) to ferrocenium (Fc + ), and the simultaneous PEC water splitting reactions at the TNRs that protonate the carboxylate binding groups. This dual photoelectrochemically‐driven mechanism for REE release is investigated by in situ pH measurements, as well as vibrational and X‐ray photoelectron spectroscopy. Through PEC approaches, a 68.8% reduction in energy consumption during REE recovery has been achieved compared to purely electrochemical systems, with a regeneration efficiency close to 100%. For NdFeB magnets from waste hard disk drives, Nd and Dy recovery efficiencies of 59.2 and 61.1% are achieved. The dual‐functionality of these copolymer PEC systems offers a sustainable platform for modulating critical element recovery.
Cho, Ki‐Hyun [Department of Chemical and Biomolecu↗
Influence of Linker Group on Bipolar Redox-Active Molecule Performance in Non-Aqueous Redox Flow Batteries
Redox flow batteries (RFBs) are an attractive choice for stationary energy storage of renewables such as solar and wind. Non-aqueous redox flow batteries (NARFBs) have garnered broad interest due to their high voltage operation compared to their aqueous counterparts. Further, the utilization of bipolar redox-active molecules (BRMs) is a practical way to alleviate crossover faced by asymmetric RFBs. In this work, ferrocene (Fc) and phthalimide (PI) are covalently linked with various tethering groups which vary in structure and length. The compiled results suggest that the length and steric shielding ability of the linker group can greatly influence the stability and overall performance of Fc-n-PI BRM-based NARFBs. Primary sources of capacity loss are found to be BRM degradation for straight chain spacers <6 carbons and membrane (Nafion) fouling. Fc-hexyl-PI provided the most stable battery cycling and coulombic efficiencies of >98 % over 100 cycles (~13 days). NARFB using Fc-hexyl-PI as an active material exhibited high working voltage (1.93 V) and maximum capacity (1.28 Ah L -1 ). Additionally, this work highlights rational strategies to improve cycling stability and optimize NARFB performance.
25 ENERGY STORAGE↗
Oxadiazole derivatives as stable anolytes for >3 V non-aqueous redox flow battery
Effective utilization of energy from renewable sources such as wind and solar requires the development of long duration energy storage (LDES) systems that can accommodate intermittent energy accrual. One option under investigation is the use of a redox flow battery (RFB). A significant amount of work has explored aqueous RFB systems with a variety of inorganic and organic carriers. However, moving to a nonaqueous solvent such as acetonitrile (MeCN) for RFB provides a much larger electrochemical window, which could lead to increased energy density if properly utilized. Here, in this work, we investigate a series of 2,5-diphenyl-1,3,4-oxadiazole (DiPhenOx) derivatives as anolytes for a redox flow battery. DiPhenOx has a low voltage redox event that, while reversible by cyclic voltammetry, was determined to be irreversible during bulk electrolysis. To improve cycling performance, we introduced various ester and cyano groups to the phenyl rings of DiPhenOx using molecular engineering. We characterized these derivatives spectroscopically and electrochemically to assess their feasibility for flow battery applications. The ester derivatives with the best cycling performance were tested in a flow cell vs. ferrocene, 2,5-di-tert-butyl-1,4-bis(2-methoxyethoxy)benzene (DBBB) and thianthrene, which resulted in ~2 V, ~3 V and ~3 V redox flow batteries, respectively.
25 ENERGY STORAGE↗
Redox Potentials for Hydrogen Species in Acetonitrile and Tetrahydrofuran
The properties of the fundamental hydrogen species, proton (H+), hydrogen atom (H•), and hydride anion (H-) are critical to a vast range of chemical processes, yet their thermodynamic properties in nonaqueous solvents are not well established. A hybrid supermolecule-continuum approach is used to predict the Gibbs free energies of solvation (?G°solv) and standard redox potentials (E°) for the 2H+/H2 and H•/H- couples in acetonitrile (MeCN) and tetrahydrofuran (THF) following the approach previously used for water. Gas phase geometry optimizations were done using density functional theory (DFT) with the ?B97XD functional, Møller-Plesset second-order perturbation theory (MP2) with augmented correlation-consistent basis sets and composite-correlated molecular orbital theory (G3MP2 and G3MP2B3). Additional single point calculations in gas phase were performed for H- affinity for MeCN and THF at the coupled cluster CCSD(T) level using MP2 geometries. Solvation was included using the self-consistent reaction field SMD model. For H+, the ?G°solv values are predicted to be -252.2 kcal/mol in MeCN and -261.0 kcal/mol in THF. The redox potentials for the 2H+/H2 couple are +0.49 V in MeCN and +0.11 V in THF relative to the aqueous SHE, consistent with the available experimental data. The ?G°solv for H- is predicted to be -80 kcal/mol in MeCN and -68 in THF, and for H•, ?G°solv is predicted to be -1.3 kcal/mol in THF and -2.0 kcal/mol in MeCN. These solvation energies yield respective calculated redox potentials for the H•/H- couple of -0.14 V in MeCN and -0.68 V in THF relative to the aqueous SHE. H2 solvation is slightly exergonic in MeCN (-3.3 kcal/mol) and near thermoneutral in THF (+1.3 kcal/mol). The pKa(H2) is predicted to be 45.4 in MeCN and 47.8 in THF. The proton-coupled electron transfer (PCET) accounting term CG was evaluated giving values on the ferrocene scale within approximately 2 kcal/mol of literature in both solvents. These results provide benchmarks for hydrogen redox chemistry in MeCN and THF and improve consistency across E°, ?G°solv, pKa, and CG. These results provide benchmarks for hydrogen redox chemistry in nonaqueous media challenging previous estimates based on indirect extrapolations and assumptions.
Duda, Damian P.↗