Search NASA⌕ Search

SEARCH · Search NASA

Results for “FFF”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Conclusions • Multimaterial and isotopically-labeled specimens were successfully fabricated via FFF-AM • Raman spectroscopy, atomic force microscopy, and neutron scattering show promise for direct measurements of interlayer diffusion in the multimaterial and isotopically-labeled specimens • Although isotopically-labeled specimens offer the greatest potential for experimentally verifying FFF-AM process models, substituting hydrogen with deuterium alters the thermal and rheological properties of the HDPE polymer

Multimaterial and Isotopically Labeled Specimen Fabrication via Material Extrusion Additive Manufacturing for Interlayer Diffusion Analysis

Jones, Haley W. [Savannah River National Laborator↗
DOE OSTI2019

Guidance on the Use of Existing ASTM Polymer Testing Standards for ABS Parts Fabricated Using FFF

When evaluating the static mechanical performance of fused filament fabrication (FFF) polymers, researchers have conducted tensile testing using American Society for Testing Materials International (ASTM) D3039 rectangular test specimens and ASTM D638 Type I and Type IV dogbone test specimens. The choice of ASTM D638 versus ASTM D3039 test specimen geometry is usually based on the perceived susceptibility of the ASTM D638 test specimens to failure within the fillet radius. ASTM polymer and plastic tensile test standards define criteria for acceptably tested specimens as requiring failure inside the narrow length (i.e., ASTM D638) or outside of the grips (i.e., ASTM D3039) for the results to be considered acceptable. There has been limited published research regarding the selection of an ASTM test specimen geometry for FFF polymer materials. This study provides evidence-based guidance through the comparison of the mechanical performance and failure acceptance rates of ASTM D3039 and ASTM D638 test specimen geometries, fabricated using FFF acrylonitrile butadiene styrene (ABS). Here, the purpose of the study is to provide guidance on the use of existing ASTM polymer testing standards for additively manufactured polymers. Results indicate there is an inherent benefit to using ASTM D3039 over ASTM D638 Type I and Type IV test specimens for tensile testing. ASTM D3039 test specimens provide the most consistent failure within the test specimen’s gage length, which is attributed to the rectangular design of the test specimen. Results also indicated that, like traditionally manufactured polymer composites, there will be differences in the tensile test results (e.g., ultimate tensile strength, elastic modulus) based on the different cross-sectional areas of the test specimen geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Preliminary Characterization and Evaluation on FFF Manufactured 316H and ODS Steels

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross-cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. The overarching vision of AMMT is to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy. Solid-state advanced manufacturing techniques can overcome some of the challenges in liquid-based additive manufacturing (AM) processes and should therefore be considered in material design and manufacturing as well. The work presented in this report forms part of a study on solid-state AM techniques of 316 stainless steels (SS) and oxide dispersion strengthened (ODS) steel components and supports the vision and goals of the AMMT program relevant to accelerate the development and deployment of advanced manufacturing processes. Achieving this can provide a safety improvement through larger safety margins, economic benefit for higher efficiency during operation, and a cost reduction through more effective manufacturing processes and less waste. This study provides preliminary information on development of the fused-filament fabrication (FFF) process using different powder types to demonstrate the sensitivity, and therefore the characterization of these sample components. The full solid-state manufacturing feasibility study will be completed and reported in a final feasibility evaluation during 2025. The study investigation used two 14YWT ODS powder batches, which provided information and the effect of different powder morphologies on manufacturability. The two 316SS powders demonstrated the effect of powder size on the manufacturability using FFF. Two product forms, namely a honeycomb structure and flat samples, were manufactured to demonstrate the flexibility of product form.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Enabling On-Demand Aerospace Component Manufacturing: Topology Optimization of GE Engine Bracket and Fabrication Using Metal FFF

Additive Manufacturing (AM) offers advantages over conventional manufacturing processes, particularly by reducing the number of parts produced through multistage combined technologies, but these often result in low manufacturing yields or require post-processing. AM facilitates the production of complex geometries with fine features, overhangs, and lattice structures. For instance, Laser Powder Bed Fusion (LPBF) technology enables the fabrication of intricate parts that can be easily post-processed by removing residual powder. Laser powder bed AM technologies are widely discussed in the literature due to their design freedom in creating complex geometries, with and without the need for support generation. However, rapid solidification due to a thermal gradient in the build direction, which leads to the formation of columnar grains and warpage, is one of the challenges. To address this challenge, we propose layer-by-layer metal FFF technology, followed by the debinding and sintering process, as an alternative to powder- and laser-based approaches. Furthermore, design for additive manufacturing (DfAM) principles are discussed to minimize the need for support generation and enable easy post-processing, thereby improving surface finish to meet high tolerances in fabricating components for aerospace and healthcare applications.

Singh, Abhishek [University of Michigan, Ann Arbor↗
NASA NTRS2011

Separation of Single-Walled Carbon Nanotubes with DEP-FFF

A process using a modified dielectrophoresis device separates single-walled carbon nanotubes (SWNTs) according to their polarizability in electric fields. This depends on the size and dielectric constant of individual nanotubes and easily separates metallic from semiconducting nanotubes. Separation by length has also been demonstrated. Partial separation (enrichment) according to bandgap (which is linked to polarizability) has also been shown and can be improved to full separation of individual types of semiconducting SWNTs with better control over operational parameters and the length of SWNT starting material. This process and device can be scaled affordably to generate useful amounts of semiconducting SWNTs for electronic device development and production. In this study, a flow injection dielectrophoresis technique was used with a modified dielectrophoresis device. The length, width, and height of the modified chamber were 28, 2.5, and 0.025 cm, respectively. On the bottom of the chamber, there are two arrays of 50-m-wide, 2-m-thick gold electrodes, which are connected to an AC voltage generator and are alternately arranged so that every electrode is adjacent to two electrodes of the opposite polar. There is an additional plate electrode on the top of the chamber that is negatively biased. During the experiment, a syringe pump constantly pumps in the mobile phase, 1-percent sodium dodecylbenzene sulfonate (SDBS) solution, into the chamber. The frequency and voltage are set to 1 MHz and 10 V peak-to-peak, respectively. About 150 micro-L of SWNTs in 1- percent SDBS decanted solution are injected to the mobile phase through a septum near the entrance of the chamber. The flow rate of the mobile phase is set to 0.02 cu cm/min. The injected SWNTs sample flows through the chamber before it is lead into a fluorescence flow-through cell and collected for further analysis. The flow-through cell has three windows, thus allowing the fluorometer to collect fluorescence spectrum and visible absorption spectrums simultaneously. Dielectrophoresis field-flow fractionation (DEP-FFF) generally depends on interaction of a sedimentation force and DEP force for particle separation, and SWNTs are neutrally buoyant in water. In this innovation, the third electrode was added to create a sedimentation force based on DC electrophoresis. This makes this particular device applicable to separations on any neutrally buoyant particles in solution and a more general process for a broad range of nanomaterials sorting and separations.

Schmidt, Howard K.↗
NASA NTRSDate not supplied

Application of Regolith Polymer Composite FFF Construction in Simulated Lunar Conditions

NASA’s Artemis program has the lofty goal of creating a sustained lunar presence to provide unprecedented opportunities for scientific discovery and to ensure American industry’s access to the unlimited resources and commercial potential in space. To achieve this goal, NASA must incrementally develop and expand its capabilities beyond the short lunar stays of the Apollo program to a robust continued presence with infrastructure and equipment to reduce mission risk by providing safer and more reliable access to the surface, its resources, and protection from the environment. Kennedy Space Center’s Swamp Works Granular Mechanics and Regolith Operations laboratory has partnered with AI SpaceFactory to develop the architectural and structural design of a robotically constructable unpressurized shelter. The shelter, called Lina is designed to protect astronauts and surface assets from radiation, meteoroid impact, moon quakes and thermal gradients. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites was developed. The construction system and associated print parameters are discussed along with the environmental simulation equipment and a summary of test conditions. Test samples were printed in simulated lunar dirty thermal vacuum conditions (~-180 C, ~10-3 torr) and subjected to a series of tests. The resulting strength properties are summarized here, the full details of the material characteristics are provided in a related paper. Lina’s structural design criteria and the resulting initial structure design are detailed in two related papers, this paper presents an update to Lina’s design based on the achieved material strength properties. Finally, a scaled down version of the updated Lina was built on a regolith simulant surface using a novel anchoring technique in simulated lunar vacuum conditions.

lunar infrastructure↗
DOE OSTI2022

Development of Long Fiber Filled Materials for Fused Filament Fabrication (FFF) (Phase 2)

ORNL worked with 3D Platform to develop new hardware and systems for their largest product, a medium format pellet system known as the WorkCenter 500. 3D Platform provided an Alpha version of the system for ORNL to begin development and systems integration. ORNL focused efforts on integrating a new dryer, safety enclosure, extruder, and build table for improved operation of the system.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

The use of fused filament fabrication (FFF) acrylonitrile butadiene styrene (ABS) and other thermoplastics in radiation environments is beginning to be studied as possible replacements for traditionally manufactured parts and tools. Interlayer adhesion within the mesostructure has been shown in published literature to be an integral component in the strength of FFF ABS. Research of irradiated 3D printed polymers has primarily focused on the influence of gamma irradiation on the mechanical properties of FFF ABS samples, without evaluating its impact on the mesostructure of the samples. The purpose of this paper is to understand the mechanical damage caused by proton radiation on FFF ABS samples through the evaluation of the mesostructure of the ABS samples. To achieve this objective, proton radiation at 40 MeV was applied to FFF ABS samples at radiation doses up to 1.0 MGy at a dose rate of 1 MGy/hr. Following the irradiation, tensile testing was performed on the samples. Here, the fractured surfaces of the tested samples were subsequently observed using a scanning electron microscope. The mechanical test results show an increase in the ultimate tensile strength (UTS) and a decrease in the ductility of the irradiated samples. Statistical analysis on the results shows that there is a statistically significant difference in the UTS and the ductility of unirradiated and 1.0 MGy irradiated samples and between irradiated samples and 1.0 MGy samples. In addition, the percentage elongation at break has statistically significant differences in the means between irradiated samples and 1.0 MGy samples. The UTS has statistically significant differences in the means between 0.1 MGy and 1.0 MGy. The difference in the means between the unirradiated and the 1.0 MGy samples is the most significant for both the UTS and elongation at break. The scanning electron microscopy (SEM) results indicated that interlayer adhesion improved as a function of radiation dose corresponding to the increase in tensile strength. The SEM results also showed that crazing and plastic deformation were reduced; aligning with the loss in ductility observed in the tensile tests results. The proton radiation is causing these mechanical and physical changes through two mechanisms: (1) dose rate effects on ionizing radiation-induced oxidative degradation; and (2) radiation heating effects of high energy (>1 MeV) charged particles.

electron microscopy↗
DOE OSTI2022

Fused Filament Fabrication of Polycarbonate in a Reactive Atmosphere

Fused Filament Fabrication (FFF) has become extremely useful in various industries, particularly when complex parts are needed in low volumes. However, the material properties available in FFF polymers are limited in scope. The properties of a FFF part can be changed in multiple ways. This study explores changing the bulk properties of a part by affecting each layer as it prints. Prior work has demonstrated the feasibility of altering polymer properties by layerwise exposure to a liquid chemical, but properties have never been modified in situ using a reactive gas. Here, FFF is done in the presence of a reactive gas. Specifically, the part is printed with polycarbonate in a reactive atmosphere of ozone and ultra-violet light. It was found that as each layer is exposed to a reactive gas, the bulk properties of the part change. A visual chemical change was seen, as well as confirmation of the reaction through Fourier transform infrared spectroscopy attenuated total reflectance. The change in mechanical properties was measured through Dynamic Mechanical Analysis shear tests, showing a bulk change can be efficiently produced through FFF in a reactive atmosphere.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mica filled polyetherketoneketones for material extrusion 3D printing

Polyetherketoneketone (PEKK) has superior physical properties to most available thermoplastics compatible with material extrusion-based 3D printing, including analogs in the polyaryletherketone (PAEK) family. To date, the performance of fused filament fabrication (FFF) compatible PEKK has been detailed primarily as a function of varying the isomer ratios composing the co-polymer structure. The strategy to form blends or composites with PEKK for FFF is attractive for further tailoring of performance in application, yet has received limited attention. Here, we report the integration of three grades of mica platelets into PEKK at 10% and 30% mass loadings to generate an array of filament feedstocks that were then used to print objects with a simple FFF machine. The effects of mica coating chemistry and surface treatment on the compatibility with PEKK and resulting properties are described. Mica fillers at both loadings have only subtle influence on the FFF relevant melt rheological properties inherent to PEKK. Pigment micas at high loadings can lower the melting temperature of PEKK (up to 19 ºC) without shifting its glass transition temperature and inhibit much of the undesirable crystallization occurring during processing with unfilled PEKK. The printed composites were effectively cold crystallized post-printing, affording crystalline fractions up to 90% relative to unfilled PEKK with increased dimensional stabilities. All micas, when used as fillers in low and high relative PEKK crystallinities, significantly increased the tensile modulus (as high as 126% or to 7.31 GPa) of parts in correlation to the loading. Furthermore, the underlying microstructural features of a printed composite were compared to unfilled PEKK by use of a high-resolution helical micro-computed tomography instrument. Practically, pigment micas can confer a wide range of rich colors to 3D-printed PEKK.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effects of surface treatments on ABS mechanical properties from fused filament fabrication

This paper examines the influence of surface treatments on the mechanical properties of acrylonitrile butadiene styrene (ABS) samples printed by fused filament fabrication (FFF). Prior efforts have applied brushing, painting, solvent dipping, infiltration, and vapor smoothing as post-processing surface treatments to improve the mechanical properties of FFF components. Additionally, because FFF can produce components with undesirable surface roughness, mechanical abrasion, epoxy coating, and acetone treatment may increase tensile strength by decreasing stress concentrations. Ridged surface texture may provide desirable tribological or handling properties. Based on these opportunities, this paper investigates abrasive media blasting, epoxy coating, acetone immersion, and ridged texturing surface treatments on the tensile strength and other mechanical properties of FFF ABS samples. ASTM D638-14 Type-I samples were printed, treated on all sample sides, and tested. From tensile tests, the elastic modulus, tensile strength, and fracture strain for both the untreated and treated ABS samples were calculated. For each sample, the surface finish and fracture macromorphology were observed with optical microscopy and the roughness values for the surface finish were calculated from profilometer data. Furthermore, samples were submerged in water and weighed periodically to measure mass changes due to water absorption. From surface profilometry and optical miscopy data, mechanical media blasting, epoxy coating, and immersion in all concentrations of acetone decreased surface roughness. Overall, on average, grit blasting with large beads and epoxy coating led to 2.6% and 1.2% increases in tensile strength, respectively; immersion in 40% acetone led to a 1.9% increase in tensile strength while treatment in 60% and 80% acetone decreased tensile strength by 4.9% and 1.9%, respectively. The study concludes that only grit blasting with large beads, immersion in 60% acetone, and the ridged texture significantly affected the tensile strength.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Polymer composites for fused filament fabrication and methods of making the same

Disclosed are compositions of a fused filament fabrication (FFF) composite filament having embedded functional materials in a thermoplastic matrix. Methods of making the composite filaments are also disclosed. In one example, a FFF composite filament incorporates a MOF, in an amount greater than 10% by mass, dispersed in a matrix polymer. One example of a method of synthesizing FFF composite filaments involves mixing a suspension that has a MOF with a matrix polymer solution to yield a polymer-MOF mixture. The mixture is cast and dried into a solid composite material, which is formed a FFF composite filament having the MOF in an amount greater than 10% by mass.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fused filament fabrication of thermoplastic polyurethane composites with microencapsulated phase-change material

Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.

25 ENERGY STORAGE↗
DOE OSTI2022

Closed-loop additive manufacturing of upcycled commodity plastic through dynamic cross-linking

A sustainable closed-loop manufacturing would become reality if commodity plastics can be upcycled into higher-performance materials with facile processability. Such circularity will be realized when the upcycled plastics can be (re)processed into custom-designed structures through energy/resource-efficient additive manufacturing methods, especially by approachable and scalable fused filament fabrication (FFF). Here, we introduce a circular model epitomized by upcycling a prominent thermoplastic, acrylonitrile butadiene styrene (ABS) into a recyclable, robust adaptive dynamic covalent network (ABS-vitrimer) (re)printable via FFF. The full FFF processing of ABS-vitrimer overcomes the major challenge of (re)printing cross-linked materials and produces stronger, tougher, solvent-resistant three-dimensional objects directly reprintable and separable from unsorted plastic waste. This study thus offers an imminently adoptable approach for advanced manufacturing toward the circular plastics economy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2016

High Temperature Thermoplastic Additive Manufacturing Using Low-Cost, Open-Source Hardware

Additive manufacturing (or 3D printing) via Fused Filament Fabrication (FFF), also known as Fused Deposition Modeling (FDM), is a process where material is placed in specific locations layer-by-layer to create a complete part. Printers designed for FFF build parts by extruding a thermoplastic filament from a nozzle in a predetermined path. Originally developed for commercial printers, 3D printing via FFF has become accessible to a much larger community of users since the introduction of Reprap printers. These low-cost, desktop machines are typically used to print prototype parts or novelty items. As the adoption of desktop sized 3D printers broadens, there is increased demand for these machines to produce functional parts that can withstand harsher conditions such as high temperature and mechanical loads. Materials meeting these requirements tend to possess better mechanical properties and higher glass transition temperatures (Tg), thus requiring printers with high temperature printing capability. This report outlines the problems and solutions, and includes a detailed description of the machine design, printing parameters, and processes specific to high temperature thermoplastic 3D printing.

Gardner, John M.↗