Search NASA⌕ Search

SEARCH · Search NASA

Results for “FINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Parametric Fin-Body and Fin-Plate Database for a Series of 12 Missile Fins

A cooperative experimental investigation has been performed to obtain a systematic fin-body and fin-plate database for a series of 12 missile fins. These data are intended to complement and extend the information contained in the Triservice missile project and to provide a systematic set of experimental data from which fin-body interference factors can be derived. Data were obtained with the fins mounted on both an axisymmetric body and on a flat plate that was used to simulate fin-alone measurements. The experiments were conducted at Mach numbers from 0.60 to 3.95; fin deflection angles of 0 deg, 10 deg, and -10 deg; and angles of attack up to 30 deg on the body and up to 95 deg on the flat plate. The data were obtained from three-component balances attached to the fins and a six-component balance located in the axisymmetric body. The data obtained in this project are documented in tabular form in this report. In addition, selected data are presented in graphical form to illustrate the effects of the test variables. These variables are configuration angle of attack; Mach number; and fin parameters of deflection angle, planform size, taper ratio, and aspect ratio. A very limited comparison with the Triservice missile data is made to illustrate the consistency between the data from these two projects.

Allen, Jerry M.↗

Effect of Fin Passage Length on Optimization of Cylinder Head Cooling Fins

The heat transfer performance of baffled cooling fins on cylinder heads of small, air-cooled, general-aviation aircraft engines was analyzed to determine the potential for improving cooling fin design. Flow baffles were assumed to be installed tightly against the fin end edges, an ideal baffle configuration for guiding all flow between the fins. A rectangular flow passage is thereby formed between each set of two adjacent fins, the fin base surface, and the baffle. These passages extend around each side of the cylinder head, and the cooling air absorbs heat as it flows within them. For each flow passage length, the analysis was concerned with optimizing fin spacing and thickness to achieve the best heat transfer for each fin width. Previous literature has been concerned mainly with maximizing the local fin conductance and has not considered the heating of the gas in the flow direction, which leads to higher wall temperatures at the fin passage exits. If the fins are close together, there is a large surface area, but the airflow is restricted.

Siegel, R.↗

Subsonic pressure distributions near a wing-fin juncture on a supersonic arrow-wing configuration with wing-mounted vertical fins

A generic supersonic arrow-wing configuration has been extensively studied to develop a consistent experimental data base to aid in verifying analytical prediction methods. One of the wing configurations studied was a twisted and cambered wing with wing-mounted vertical fins and trailing-edge flaps. The pressure data obtained on that configuration was limited in the wing-fin juncture region, and no pressures were obtained on the fin itself. However, detailed data in the juncture region and on the fin are essential to check out the analytical prediction methods. Therefore, the model was modified to provide details of the juncture pressure field as well as pressures on the fin. The results of this experimental investigation showed that the addition of a fin helped improve the wing pressure distribution outboard of the fin. Deflection of the trailing-edge flap did not adversely affect this trend. The pressure distributions on the vertical fin were generally affected more by change in angle of attack than by flap deflection. The spanwise pressure distribution on the fin itself indicated a load reversal with angle of attack.

Huffman, J. K.↗

Heat Dissipation from a Finned Cylinder at Different Fin-Plane/Air-stream Angles

This report gives the results of an experimental determination of the temperature distribution in and the heat dissipation from a cylindrical finned surface for various fin-plane/air-stream angles. A steel cylinder 4.5 inches in diameter having slightly tapered fins of 0.30-inch pitch and 0.6 -inch width was equipped with an electrical heating unit furnishing 13 to 248 B.T.U. per hour per square inch of inside wall area. Air at speeds form 30 to 150 miles per hour was directed at seven different angles from 0 degrees to 90 degrees with respect to the fin planes. The tests show the best angle for cooling at all air speeds to be about 45 degrees. With the same temperature for the two conditions and with an air speed of 76 miles per hour, the heat input to the cylinder can be increased 50 percent at 45 degrees fin-plane/air-stream angle over that at 0 degrees.

Schey, Oscar W↗

Aerodynamic static stability characteristics, fin effectiveness, and fin location of the MSFC 33-foot pressure fed booster at high angles of attack

Experimental aerodynamic investigations were conducted in the NASA/MSFC 14 x 14 inch trisonic wind tunnel during early February 1972 on a 0.00280 scale model of the MSFC 33-foot diameter space shuttle pressure fed booster configuration. The basic configuration tested was a 40 deg cone/cylinder/7 deg frustrum designated the MSFC 33 foot pressure fed booster. Six component aerodynamic force and moment data were recorded over a Mach number range from 0.9 to 5.0 at angles of attack from +20 to +90 at 0 deg sideslip and over a sideslip range from -10 to +10 deg at 30, 50, 60 and 80 deg angles of attack. Primary configuration variables were fin deflection angle and vertical position on the frustrum.

Hamilton, T.↗

An Investigation of the Aerodynamic Characteristics of an 0.08-Scale Model of the Chance Vought XF7U-1 Airplane in the Langley High-Speed 7- by 10-Foot Tunnel. Part V - Wing-Alone Tests and Effect of Modifications to the Vertical Fins, Speed Brakes, and Fuselage TED No. NACA DE308: Wing-Alone Tests and Effect of Modifications to the Vertical Fins, Speed Brakes, and Fuselage, TED No. NACA DE308 - Part V

Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The wing-alone tests and the effect of the various vertical-fin modifications, speed-brake modifications, and fuselage modifications on the aerodynamic characteristics in pitch and yaw are presented in the present paper with a limited analysis of the results. Also included are tuft studies of the flow for some of the modifications tested.

Kuhri, Richard E.↗

Grid Fin Stabilization of the Orion Launch Abort Vehicle

Wind tunnel tests were conducted by Nielsen Engineering & Research (NEAR) and Rose Engineering & Research (REAR) in conjunction with the NASA Engineering & Safety Center (NESC) on a 6%-scale model of the Orion launch abort vehicle (LAV) configured with four grid fins mounted near the base of the vehicle. The objectives of these tests were to 1) quantify LAV stability augmentation provided by the grid fins from subsonic through supersonic Mach numbers, 2) assess the benefits of swept grid fins versus unswept grid fins on the LAV, 3) determine the effects of the LAV abort motors on grid fin aerodynamics, and 4) generate an aerodynamic database for use in the future application of grid fins to small length-to-diameter ratio vehicles similar to the LAV. The tests were conducted in NASA Ames Research Center's 11x11-foot transonic wind tunnel from Mach 0.5 through Mach 1.3 and in their 9x7-foot supersonic wind tunnel from Mach 1.6 through Mach 2.5. Force- and moment-coefficient data were collected for the complete vehicle and for each individual grid fin as a function of angle of attack and sideslip angle. Tests were conducted with both swept and unswept grid fins with the simulated abort motors (cold jets) off and on. The swept grid fins were designed with a 22.5deg aft sweep angle for both the frame and the internal lattice so that the frontal projection of the swept fins was the same as for the unswept fins. Data from these tests indicate that both unswept and swept grid fins provide significant improvements in pitch stability as compared to the baseline vehicle over the Mach number range investigated. The swept fins typically provide improved stability as compared to the unswept fins, but the performance gap diminished as Mach number was increased. The aerodynamic performance of the fins was not observed to degrade when the abort motors were turned on. Results from these tests indicate that grid fins can be a robust solution for stabilizing the Orion LAV over a wide range of operating conditions.

Pruzan, Daniel A.↗

Stability and control characteristics of a monoplanar missile configuration with triform-tail-fin arrangements at Mach numbers from 1.70 to 2.86

A wind-tunnel missile model with either a lower vertical tail fin with a pair of horizontal fins having 0 deg, 22.5 deg, or 30 deg dihedral or an upper vertical tail fin with horizontal fins having 0 deg, -22.5 deg, or -30 deg dihedral was investigated. The results indicated that those configurations with horizontal fins at or below the horizontal plane had nearly linear pitching-moment characteristics, while those with the horizontal fins above the horizontal plane experienced pitch-up which increased with increasing horizontal-fin-dihedral angle. At zero angle of attack, the configurations were directionally stable at most test Mach numbers. Generally, those configurations with the upper vertical fin had positive effective dihedral at zero angle of attack, while those with he lower vertical fin had negative effective dihedral. For roll control, three deflected tail fins produced more total roll control than two horizontal fins. For yaw control, three tail fins deflected equally or differentially produced more total yaw control than the single vertical fin.

Lamb, M.↗

Wind Tunnel Investigation of Fuselage Stability in Yaw with Various Arrangements of Fins

An investigation was made in the 7-by-10 foot wind tunnel to determine the effects of dorsal-type fins and various arrangements of fins on the aerodynamic characteristics of a streamline circular fuselage. Comparative plots of the aerodynamic characteristics of the fuselage alone and the fuselage with various fin arrangements are given to show their effects on coefficients of yawing moment, drag, and lateral force. Results are also given for one case in which a rear fin on a circular fuselage was faired with modeling clay to obtain a fuselage shape with the same side elevation as the fuselage with the unfaired fin but with an elliptical cross section over the rearward portion of the fuselage. The results indicated that fin area to the rear of the center of gravity of the fuselage was beneficial in reducing the magnitude of the unstable yawing moments at large angles of yaw; whereas, fin area forward of the center of gravity was harmful. The dorsal-type fin was more effective for increasing the yawing stability of the fuselage than was a smoothly faired rearward portion with the same side elevation as the fuselage with the unfaired dorsal type fin. The minimum drag coefficient and the slope of the curve of yawing-moment coefficient of the fuselage at zero yaw were unaffected by the addition of the fins, within the experimental accuracy of the tests.

Hoggard, H Page, Jr↗

Comparison of the Effectiveness of Flares With That of Fins for Stabilizing Low Fineness Ratio Bodies at Mach Numbers From 0.6 to 5.8

An experimental and analytical investigation has been made of the effectiveness of flares and of fins for providing aerodynamic stability of low-fineness-ratio bodies near zero angle of attack. Wind-tunnel tests were performed at Mach numbers from 0.6 to 3.8 to measure the normal force, center of pressure, and drag of bodies consisting of conical noses in combination with cylindrical midsections and finned or flared aftersections. This study included an investigation of the effects of nose bluntness, midbody length, flare angle (from 0° to 20°), and fin leading-edge bluntness. The results showed that for the same plan-form area, flares were more effective than fins, but for the same drag, fins were more effective than flares. Flow separation, which occurred ahead of a flare at certain Mach numbers, resulted in an increase in the stabilizing effectiveness of the flare and a decrease in the drag. However, flow separation led to large undesirable shifts in the center of pressure. Blunt fins were found to be more effective than sharp fins, with the vertical as well as the horizontal fins contributing to the effectiveness. Comparisons of the analytical with the experimental results indicated that the analytical method employed gave good estimates of the stabilizing effectiveness of both fins and flares throughout the supersonic Mach number range.

Leland H Jorgensen↗