Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAME PROPAGATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Hierarchically Informed Engineering Models for Predictive Modeling of Turbulent Premixed Flame Propagation in Pre- chamber Turbulent Jet Ignition

The goal of the project is to improve the predictive accuracy and efficiency of turbulent combustion sub-models for pre-chamber turbulent jet ignition (TJI). This goal is achieved through the development of a hierarchically informed engineering model for turbulent combustion in TJI. The model development starts with the highest level of model description of turbulent combustion with direct numerical simulation (DNS) from which fundamental characteristics and scaling properties of turbulent premixed flame propagation under TJI relevant conditions are obtained.

42 ENGINEERING↗
DOE OSTI2025

Plasma assisted NH 3 /H 2 /air ignition in nanosecond discharges with non-equilibrium energy transfer

Ammonia (NH 3 ), with its high energy density and easiness to store and transport as a hydrogen carrier, has become a promising alternative green fuel. However, its adoption in power generation is hindered by challenges such as low burning velocity, slow low-temperature oxidation, high NO x emissions, and ignition difficulty. Here, this work computationally investigates the effects of non-equilibrium energy transfer by nanosecond discharges on NH 3 ignition and flame propagation in an NH 3 /H 2 /air flow at 700 K and 1 atm. The simulation results demonstrate that NH 3 /air mixtures require a large ignition energy due to their large critical ignition radius. It is shown that adding 30 % hydrogen significantly reduces the critical ignition radius and minimum ignition energy. Two-dimensional modeling further shows a non-monotonic dependence of ignition kernel volume on the applied voltage and reduced electric field. The optimum ignition enhancement occurs at 200 Td where the generation of electronically excited species and radicals including N 2 (B), O( 1 D) and OH becomes most efficient. Higher voltages divert electron energy toward ionization, which makes it less effective for NH 3 ignition. The study also identifies an optimal electrode gap size for a given pulse energy. Smaller gap sizes increase deposited energy density, raising temperature and radical concentrations. However, excessive reduction of the gap distance reduces flame propagation speed due to the flame stretch effect in rich mixtures with the effective Lewis number greater than unity. A nonlinear relationship between pulse repetition frequency and ignition kernel volume is observed in a nanosecond pulsed high frequency discharge (NPHFD). An optimal frequency range of 200 kHz to 2 MHz is found when two pulses are used. In addition, an optimal number of pulses exists for each pulse repetition frequency, with higher frequencies requiring more pulses to maximize the overlap region. These findings provide critical insights on developing controlled plasma discharge techniques for efficient NH 3 ignition in reactive flows within internal combustion engines and gas turbines.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Direct numerical simulation of a high-pressure hydrogen micromix combustor: Flame structure and stabilisation mechanism

A high-pressure hydrogen micromix combustor has been investigated using direct numerical simulation with detailed chemistry to examine the flame structure and stabilisation mechanism. The configuration of the combustor was based on the design by Schefer et al., using numerical periodicity to mimic a large square array. A precursor simulation of an opposed jet-in-crossflow was first conducted to generate appropriate partially-premixed inflow boundary conditions for the subsequent reacting simulation. The resulting flame can be described as an predominantly-lean inhomogeneously-premixed lifted jet flame. Five main zones were identified: a jet mixing region, a core flame, a peripheral flame, a recirculation zone, and combustion products. The core flame, situated over the jet mixing region, was found to burn as a thin reaction front, responsible for over 85% of the total fuel consumption. The peripheral flame shrouded the core flame, had low mean flow with high turbulence, and burned at very lean conditions (in the distributed burning regime). It was shown that turbulent premixed flame propagation was an order-of-magnitude too slow to stabilise the flame at these conditions. Stabilisation was identified to be due to ignition events resulting from turbulent mixing of fuel from the jet into mean recirculation of very lean hot products. Ignition events were found to correlate with shear-driven Kelvin-Helmholtz vortices, and increased in likelihood with streamwise distance. At the flame base, isolated events were observed, which developed into rapidly burning flame kernels that were blown downstream. Further downstream, near-simultaneous spatially-distributed ignition events were observed, which appeared more like ignition sheets. The paper concludes with a broader discussion that considers generalising from the conditions considered here.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

2D CFD of lean premixed hydrogen–air flame quenching under locomotive engine conditions

Hydrogen (H 2 ) is a promising fuel for reducing emissions in heavy-duty internal combustion engines (ICEs), but its low quenching distance increases the risk of flame propagation into narrow crevice regions, such as piston-liner gaps. This work uses detailed CFD simulations with finite-rate chemistry to investigate premixed H 2 –air flame quenching in a two-dimensional (2D) region consistent with the piston-liner gap of a diesel ICE. Model accuracy was assessed by comparison with experimentally measured quenching distances in an annular stepwise diverging tube (ASDT). A parametric study was conducted to assess the influence of crevice width (0.05–1.18 mm), pressure (50–150 bar), unburned gas temperature (431–573 K), and equivalence ratio ( Φ= 0.3–0.6). Results show that the critical Péclet number for flame survival is no greater than 3.25, consistent with prior literature, even under ultra-lean and high-pressure conditions (Φ ≤ 0.3, > 50 bar). Additionally, flames with Péclet numbers exceeding 6.15 exhibited front wrinkling, suggesting the onset of velocity-driven instabilities and enhanced flame robustness. These findings help define thresholds for flame quenching in confined geometries and support the safe design of H 2 fueled ICEs.

08 HYDROGEN↗
DOE OSTI2024

Heat release surrogates for NH 3 /H 2 /N 2 –air premixed flames

The present study investigates the performance of NH, NH 2 , O-atom, and H-atom as heat release rate (HRR) surrogates for NH 3 /H 2 /N 2 –air premixed flame through simulations. The simulations are conducted across different pressures, reactant inlet temperatures, fuel blend compositions, and equivalence ratios. Cantera is used to simulate one-dimensional (1D) freely propagating flames to investigate the spatial correlations of the species with the HRR. PeleLMeX, a low-Mach direct numerical simulation (DNS) code with Adaptive Mesh Refinement (AMR), is used to simulate two-dimensional (2D) flame-vortex interactions to investigate the temporal correlations including stretch effects. Three different mechanisms (Jiang et al. 2020; Glarborg et al. 2018; Okafor et al. 2018) were considered in the 1D flame simulations, whereas only the Jiang mechanism was considered in the flame-vortex simulations. The HRR surrogate performance for the 2D flames is evaluated at two different locations: (1) the centerline and (2) the flame cusp. The cusp is defined as the region in the flame front with the greatest curvature and the centerline encounters the highest tangential strain rate. The 1D flame results suggest that, although there is not uniformly good spatial correlation for HRR across all flame conditions, NH is the best overall as a HRR surrogate for laminar flames. The 2D flame results, however, suggest that O-atom and H-atom have satisfactory temporal correlations at different conditions—the former for rich flames, the latter for high-pressure flames. Furthermore, these simulations provide guidance to experimental measurements of surrogate HRR markers in unsteady multi-dimensional flames using laser diagnostics to detect species such as NH, O-atom, and H-atom.

Ammonia↗
DOE OSTI2025

Theoretically Informed Kinetics (ThInK): Establishing a modern C 0 -C 3 mechanism for combustion modeling

In contrast to the adage “Models are to be used, not believed”, combustion kinetics models have been intended to be predictive in nature. Theoretical chemical kinetics is now understood to provide a firm foundation for the reaction parameters, thereby facilitating predictive simulations of chemical reactivity, even in regimes that are poorly characterized by chemical kinetic and/or combustion experiments. In this study, we describe a theory-informed kinetics model (ThInK) for small molecule combustion chemistry (H 2 and C 1 – C 3 species) that is based on the prodigious use of theoretical predictions for reaction rate coefficients, thermochemistry, and transport parameters. The distinct features of this kinetics model, which was developed over the course of several decades, are illustrated through simulations of flame propagation and auto-ignition.

Energy transfer↗
DOE OSTI2024

CFD unified approach under Eulerian–Lagrangian framework for methanol and gasoline direct injection sprays in evaporative and flash boiling conditions

Innovative synthetic fuels for advanced propulsion systems, such as methanol and ammonia, and synthetic blended fuels (E00, E10, and E30), known for their high volatility, are often injected directly into combustion chambers. It follows that Eulerian–Lagrangian spray models need to accurately capture the spray collapse as a consequence of flash boiling onset and be capable of proficiently handling the preferential evaporation of multi-component fuels in evaporative scenarios. So, we performed the assessment of an Eulerian–Lagrangian CFD code for simulating methanol and E00 gasoline blend sprays in both early and late injection conditions involving flash boiling conditions and preferential evaporation. The adoption of an effervescent breakup model and of a non-equilibrium phase transition model for the discrete phase allows the adoption of a setup that is almost completely free from specific constant tuning, especially for what concerns the breakup model. We validated the simulations using experimental PLV maps of methanol and E00 sprays issued from the ECN Spray M injector. The results highlight a significantly different morphology of the methanol spray compared to the E00 one under late injection conditions. Under stratified combustion, low-volatile fuels are likely to be ignited first, and the flame propagates toward the high-volatile fuels. In conclusion, the spray collapse was also correctly reproduced, inducing the presence of a low-pressure zone and modifying the spray morphology.

E00↗
DOE OSTI2025

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗
DOE OSTI2025

Evaluating Chemical Kinetics Predictions for Propane Using 3-D and 0-D Models in a Boosted Spark-Ignited Engine

Propane has been shown to be a promising alternative fuel to reduce emissions while simultaneously achieving high efficiencies in medium- and heavy-duty engines. These high-power density applications require boosted engines which, combined with high compression ratio, can lead to auto-ignition and knock. While three-dimensional (3-D) computational fluid dynamics (CFD) models are often used for resolving the complex fluid flow in engines, these models can become computationally expensive when simulating detailed chemical kinetics. Likewise, zero-dimensional (0-D) models are computationally concise enough for kinetics development, but lack any flow-field information which governs the flame propagation processes in spark ignition (SI) engines. This work presents a comprehensive comparison between 3-D and 0-D closed cycle simulations at knocking conditions in a high compression ratio high stroke-to-bore ratio propane engine. In order to initialize the flow-field for the 3-D closed cycle (intake valve closing, (IVC) to exhaust valve opening, (EVO)) simulation, a motored multi-cycle 3-D model was run using Converge to create a map at IVC, reducing the computational time. The map allowed a non-homogeneous 3-D closed cycle simulation to be satisfactorily validated against experiments, while a homogeneous case using only the turbulence field mapping was also simulated, mimicking 0-D modeling. The 3-D simulations were used to prescribe the initial conditions (e.g., IVC thermodynamics, speciation, burn-rate profile) for a 2-zone 0-D SI engine model in Chemkin Pro for both cases. It was found that 2-zone 0-D modeling underpredicted the knock onset timing, likely due to the lack of thermal stratification in the unburned gas region. Future work will carry multi-zone 0-D modeling to capture the fuel auto-ignition in the unburned region.

Douvry-Rabjeau, Julien [Oakland University, Roches↗
DOE OSTI2024

High-Speed OH-PLIF Diagnostics of Flame Flashback in Low Swirl Hydrogen-Enriched Flames

This paper reports flashback events observed in hydrogen-enriched flames stabilized in a low swirl burner (LSB) at atmospheric pressure and temperature conditions. The fundamentals of hydrogen-rich stable flames and spatiotemporal investigation of flashback phenomena were observed experimentally using a high-repetition-rate nanosecond (ns)-duration hydroxyl radical planar laser-induced fluorescence (OH-PLIF) diagnostic. Testing was conducted in an optically accessible pre-mixing section of a LSB with inlet pre-mixing velocities ranging from 5 to 10 m/s for methane and hydrogen (50 – 90% by mole) blends. Swirlers with two different turning angles, 26o and 33o, and three different perforated plate hole diameters, 1.08, 1.12 and 1.16 mm, with measured swirl numbers varying from 0.43 to 0.49 were used in this study at atmospheric temperature and pressure inlet conditions. The flashback propensity showed a dependence on the proximity of the lifted flame to the burner exit (termed as lift-off length, L) which was dependent on the pre-mixer velocity (V), hydrogen content (XH2) and equivalence ratio (ϕ) at constant temperature and pressure conditions. High-speed OH-PLIF images revealed lifted flames were first observed at low ϕ/ XH2 condition which then changed to a M-shaped flame attached to burner rim with the increase in ϕ/ XH2. Further increases in ϕ/XH2, depending upon other inlet parameters, triggered flame flashback into the pre-mixing section. Flashback occurred when burning began in the outer shear layer and the leading flame brush propagated into the nozzle. Such spatiotemporally resolved high-speed OH-PLIF imaging provides insights on different stages of flashback in a LSB – flashback initiation, transition of flame propagation from burner exit to the swirler and flashback to flame holding transition. Flame ϕ at flashback showed an expected linearly increasing trend with increasing V and decreasing XH2 and the conclusions drawn aligned well with detailed investigations. For identical inlet conditions, flashback propensity decreased with increasing perforated-plate hole diameter and increasing swirler vane angle.

Parajuli, Pradeep↗
DOE OSTI2025

Computational diagnostics and characterization of combustion recession in diesel sprays

While low-temperature combustion (LTC) strategies have been found to mitigate nitrogen oxides and particulate matter emissions in diesel engines, studies have also associated LTC with an increase in unburnt hydrocarbons. With more recent studies on diesel after end-of-injection (AEOI), combustion recession is identified as a phenomenon where at near nozzle region, high-temperature ignition (HTI) combustion can propagate back to the nozzle tip consuming the unburnt hydrocarbons AEOI. Current literature has suggested that combustion recession is controlled by auto-ignition. However, high-fidelity simulations and detailed analysis of such a mechanism are missing. In this study, comprehensive Large Eddy Simulations of a reacting spray at “Spray A” conditions are performed, where detailed analysis of combustion recession concerning flame morphology and propagation modes are included. In particular, this study demonstrated for the first time that while combustion recession is mainly auto-ignition dominated (consistent with the literature), a cool flame was found to deflagrate towards the richer regions of the mixture, promoting mixing and increasing the mixture temperature. This leads to HTI kernels, which then grow and develop as deflagrative waves, therefore sustaining the combustion recession process. The study also detailed the extinction mechanism of combustion: the entrainment wave will overlean the near-nozzle mixtures, rendering it unable to support HTI, which leads to the extinction of the upstream flame AEOI in lower reactivity mixtures. Combustion recession is also observed to be contingent on the chemical and diffusion processes, even at low scalar dissipation rates. Finally, a new criterion for combustion recession based on chemical explosive mode is proposed and validated with previous combustion recession index to quantify the extent of HTI in near-nozzle mixtures AEOI. The newly developed metric combined with a previous experimentally-based metric can provide simple but valuable measurements of the degree and propensity of the upstream flame AEOI.

CEMA↗
DOE OSTI2024

DNS of ignition and flame stabilization in a simplified gas turbine premixer

With the increasing need for fuel flexibility, mitigation of auto-ignition (AI) inside gas turbine (GT) premixers becomes crucial. They must be designed to yield a sufficiently homogeneous fuel-air mixture to achieve low emissions while at the same time avoiding the occurrence of AI and subsequent flame stabilization. This challenge requires a detailed understanding of turbulent mixing and chemistry interactions. In the present work, a direct numerical simulation (DNS) of an array of jets in crossflow (JICF), representative of an industrial GT premixer, is reported to shed light on these complex phenomena. It is found that AI kernels form in the aft part of the premixer and coalesce into a flame front that then propagates upstream, mainly through the boundary layer, and successively engulfs the jets. This, therefore, suggests a significant role of the jet array pattern on the flame stabilization. It is noted that AI kernels continue to form independently during the whole time of the simulation. To clarify the contribution of AI and diffusion in the ignition kernels and the main flame, chemical explosive mode analysis (CEMA) is employed jointly with a kernel tracking algorithm. It is found that during the initial formation of the flame, many ignition kernels form in mixtures with low scalar dissipation rate and large contribution from AI mode. As they quickly grow, they merge into a single flame front that becomes increasingly more diffusion-assisted over time, balancing the AI mode. Turbulence is shown to have a significant enhancing effect in lean premixed flames, but further analysis is required to fully characterize it. These findings are relevant for the industrial premixer studied, and also for novel micromix concepts that may be used in the next generation of GT combustion systems.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Temperature effect on turbulent burning velocity of lean premixed hydrogen/air flames

Hydrogen has drawn great attention in recent years as a carbon-free fuel. The turbulent burning velocity (S T ) is an important parameter for the design and modeling of hydrogen-fueled engines given the high propagation speed of hydrogen flames. It has been well documented that S T of hydrogen flames can be dramatically increased by thermo-diffusive effects which are sensitive to thermodynamic conditions. Previous studies have mainly focused on the pressure effect on S T of lean hydrogen flames, while the temperature effect has been largely ignored. Here, in the present study, the turbulent burning velocity for a lean hydrogen/air mixture over a wide range of temperatures (300–641 K) and pressures (1–15 atm) is investigated through direct numerical simulations of statistically planar turbulent premixed flames. Results show that the variation of normalized turbulent burning velocity (S T /S L , where S L is the laminar flame speed) with temperature and pressure is mainly controlled by the variation of the stretching factor I 0 . While S T /S L is only marginally dependent on temperature at the atmospheric pressure, it exhibits a decreasing trend with temperature at an elevated pressure (10 atm). This is associated with different temperature dependencies of flame surface area enlargement at the two different pressures, despite the monotonically decreasing trends of I 0 with temperature at both pressures. In addition, under engine-relevant conditions where the temperature and pressure increase simultaneously, the promotion effect of pressure is found to be largely canceled out by the suppression effect of temperature, leading to only a slight increase in I 0 and S T /S L . The observed trends are further explained through detailed flame dynamic analysis. Furthermore, I 0 at different temperatures and pressures is found to correlate very well with the enhancement of fuel consumption rate in the critically strained laminar flames. The present study elucidates the strong impact of temperature on S T of lean premixed hydrogen/air flames at elevated pressures and provides new insights into the modeling of S T , especially for engine-relevant conditions.

Wang, Yiqing [Argonne National Laboratory (ANL), A↗
DOE OSTI2024

1D modeling of plasma streamers at ammonia-air flame conditions

Abstract Self-consistent 1D modeling of streamers in ammonia-oxygen-nitrogen-water mixtures has been performed in this work. A fluid model that includes species transport, electrostatic potential, and detailed chemistry was developed and verified. This model is then used to simulate the avalanche, streamer formation and propagation phases, driven by a nanosecond voltage pulse, at different thermochemical conditions derived from a 1D laminar premixed ammonia-air flame. The applicability of the Meek’s criterion in predicting the streamer inception location was successfully confirmed. Streamer formation and propagation duration were found to vary significantly with different thermochemical conditions, due to the difference in ionization rates. The thermochemical state also affected the breakdown characteristics which was tested by maintaining the background reduced electric field constant. Detailed kinetic analyses revealed the importance of O ( 1 D ) in the production of key radicals, such as O, OH, and NH 2 . Furthermore, the contributions of the dissociative electronic excitation of NH 3 towards the production of H and NH 2 radicals have also been reported. Spatial and temporal evolution of the electron energy loss fractions for various inelastic collision processes at different thermochemical states uncovered the input plasma energy spent of fuel dissociation and the large variability in the dominant processes during the avalanche and streamer propagation phases. The methodology and analyses reported in this work are key towards developing effective strategies for controlled nanosecond-pulsed non-equilibrium plasma sources used for ammonia ignition and flame stabilization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

2D Modeling of Plasma Streamer and Glow Phases at Ammonia-Air Flame Conditions

Streamer and glow plasma phases have been modeled at two thermochemical states of an ammonia-air flame: fresh reactants and burnt products. A new AMReX-based solver has been verified against benchmarks in the literature and has been used to perform these simulations. A Helmholtz-equation based photoionization model with parameters accounting for the presence of NH3 in air has been coupled with the solver to accurately model the streamer propagation phase. A detailed plasma kinetics mechanism has been compiled and used to predict the evolution of electrons, excited states, ions, and radicals during streamer propagation and glow formation. The propagation velocity of streamers was found increase by almost two-fold when the mixture was changed from the fresh reactants to the burnt products. Moreover, vibrational excitation was found to be limited to the streamer body, whereas ionization predominantly occurred at the streamer head, as is expected. Finally, the differences in the pathways of O and H radical production during the streamer propagation and glow phases have been briefly discussed.

ammonia-air flame↗
DOE OSTI2026

Examination of entrainment, combustibility, and heat transfer due to cell venting inside simplified battery energy storage enclosures

Battery energy storage systems (ESS) assembled of modules containing lithium-ion batteries can pose fire and explosion hazards during thermal runaway because vented gases may accumulate, combust, or escape enclosures. Here, we propose a prototypical configuration composed of the main components of an ESS rack, where modules are represented as rectangles within an enclosure and vent gas is injected steadily through the top of a module. This idealized geometry allows for exploration of how rack-level characteristics can influence smaller single-cell or module-level scales. Through this geometry, we conduct numerical simulations to understand how variations in the vent velocity, temperature, and vertical location affect entrainment rates, fraction of uncombusted fuel, rich-gas coverage, and heat flux to other modules. At lower vent velocities and vertical positions, buoyancy drives enough entrainment and mixing to react with most of the vent gases on the converging plenum. As jet momentum increases and/or buoyancy decreases via higher vent position in the rack, vent gases can propagate into and burn in the divergence plenum. Heat flux to the impinged module scales strongly with vent momentum and temperature, while heat transfer to upper modules peaks when flames in the diverging plenum reach the surface and declines when combustion is suppressed.

Computational fluid dynamics↗
DOE OSTI2025

A Safe Response to Renewable Energy Hazards

The International Association of Fire Fighters (IAFF) and Underwriters Laboratories, LLC (UL) in conjunction with UL Solutions initiated a joint project in 2022 under an agreement with the United States Department of Energy-Office of Energy Efficiency and Renewable Energy (DOE-EERE). This project focused on two separate and important initiatives related to energy efficiency in residential buildings. Initiative 1: Fire Performance on Energy Efficient Exterior Walls. Initiative 2: Firefighting Tactics in Residential Properties with Building Energy Storage Systems (BESS). The project’s first initiative addresses concerns surrounding new technologies with enhanced, energy-efficient exterior walls installed on residential properties. The concerns of fire rapidly traveling vertically up the exterior of these walls were examined. This addressed a growing concern from the first responder community that many times, the fires on the exterior of residential buildings have already evolved into an attic fire by the time of arrival – making it problematic to address the fire scenario. The test plan for Initiative 1 incorporated a modified version of an American Society for Testing and Materials (ASTM) test method, ASTM E2707, Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure, as the foundation of the research. The test method involved a wall structure intended to represent retrofit construction to evaluate how fire would spread vertically or laterally. The second aspect of the UL-IAFF Project focuses on the fire service response to Residential Battery Energy Storage System (RBESS) incidents. These simulation tests were constructed in the large-scale fire test facility at UL Solutions’ Northbrook, IL campus. A baseline test was conducted that involved a test structure with no batteries—shelving units populated with standardized commodities, representing a typical garage with cellulosic and plastic contents. Three additional tests have been conducted to generate data with the contribution of energy storage system (ESS) batteries to compare fire and explosion hazards against the baseline test. Through this work, fire service tactical considerations can be explored. From the data, the team can determine 1) the visual indicators of a residential fire that has involved an RBESS (or, potentially, other large batteries) and 2) the impact of fire service-initiated ventilation of the structure on the fire conditions and explosion risks.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗