Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - CHANNELS, CURVED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

Dynamic stability derivatives are evaluated on the basis of rolling-flow, curved-flow and snaking tests. Attention is given to the hardware associated with curved-flow, rolling-flow and oscillatory pure-yawing wind-tunnel tests. It is found that the snaking technique, when combined with linear- and forced-oscillation methods, yields an important method for evaluating beta derivatives for current configurations at high angles of attack. Since the rolling flow model is fixed during testing, forced oscillations may be imparted to the model, permitting the measurement of damping and cross-derivatives. These results, when coupled with basic rolling-flow or rotary-balance data, yield a highly accurate mathematical model for studies of incipient spin and spin entry.

Chambers, J. R.↗
NASA NTRS1980

Curved flow wind tunnnel test of F-18 aircraft

The curved flow capability of a stability wind tunnel was used to investigate the lateral directional characteristics of an F-18 aircraft. The model is described and the procedures used to obtain and correct the data and a graphical presentation of the results are presented. The results include graphs of lateral directional derivatives versus sideslip or static plots, the lateral directional static stability derivatives versus angle of attack, and finally the lateral directional derivatives versus nondimensional yaw rate for different angles of attack and sideslip. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these were tested with and without wing leading edge extensions.

Lutze, F. H.↗
NASA NTRS1996

A Galilean Invariant Explicit Algebraic Reynolds Stress Model for Curved Flows

A Galilean invariant weak-equilbrium hypothesis that is sensitive to streamline curvature is proposed. The hypothesis leads to an algebraic Reynolds stress model for curved flows that is fully explicit and self-consistent. The model is tested in curved homogeneous shear flow: the agreement is excellent with Reynolds stress closure model and adequate with available experimental data.

Girimaji, Sharath↗
NASA NTRS1951

Effect of Fuselage and Tail Surfaces on Low-speed Yawing Characteristics of a Swept-wing Model as Determined in Curved-flow Test Section of Langley Stability Tunnel

Results are presented of a wind-tunnel investigation made to determine the influence of the fuselage and tail surfaces on the rotary derivatives in yawing flight of a transonic-airplane configuration having 45 degrees sweptback wing and tail surfaces. The tests were run in the curved-flow test section of the Langley stability tunnel at a Reynolds number of 1.07 X 10 to the sixth power and consisted of balance measurements throughout the angle-of-attack range for several flight-path radii of curvature. The results are compared with data from forced-oscillation and free-oscillation tests, and a description of testing techniques used is included.

WIND TUNNELS↗
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

The test capabilities of the Stability Wind Tunnel of the Virginia Polytechnic Institute and State University are described, and calibrations for curved and rolling flow techniques are given. Oscillatory snaking tests to determine pure yawing derivatives are considered. Representative aerodynamic data obtained for a current fighter configuration using the curved and rolling flow techniques are presented. The application of dynamic derivatives obtained in such tests to the analysis of airplane motions in general, and to high angle of attack flight conditions in particular, is discussed.

Chambers, J. R.↗
NASA NTRS2000

Turbulence Model Predictions of Strongly Curved Flow in a U-Duct

The ability of three types of turbulence models to accurately predict the effects of curvature on the flow in a U-duct is studied. An explicit algebraic stress model performs slightly better than one- or two-equation linear eddy viscosity models, although it is necessary to fully account for the variation of the production-to-dissipation-rate ratio in the algebraic stress model formulation. In their original formulations, none of these turbulence models fully captures the suppressed turbulence near the convex wall, whereas a full Reynolds stress model does. Some of the underlying assumptions used in the development of algebraic stress models are investigated and compared with the computed flowfield from the full Reynolds stress model. Through this analysis, the assumption of Reynolds stress anisotropy equilibrium used in the algebraic stress model formulation is found to be incorrect in regions of strong curvature. By the accounting for the local variation of the principal axes of the strain rate tensor, the explicit algebraic stress model correctly predicts the suppressed turbulence in the outer part of the boundary layer near the convex wall.

Rumsey, Christopher L.↗
NASA NTRS1981

Multigrid simulation of asymptotic curved-duct flows using a semi-implicit numerical technique

Asymptotic flows inside curved ducts of rectangular as well as polar cross section are analyzed using the Navier-Stokes equations in terms of the axial velocity and vorticity and the cross-flow stream function. Numerical solutions of the three second-order coupled elliptic partial differential equations governing this flow are obtained efficiently using the coupled alternating-direction implicit (ADI) method as well as the multigrid strongly-implicit (SI) scheme. For the flow configuration studied, the ADI method is found to be more sensitive to the time steps used than is the SI scheme. Use of the multigrid-coupled-strongly-implicit (MG-SI) scheme makes it possible to efficiently obtain fine-grid solutions for configurations having strong secondary flow. It is shown that, for this asymptotic curved-duct flow, the similarity parameter of significance is the Dean's number K rather than the Reynolds number Re. Results are obtained for curved ducts with square cross sections for K up to 900, which here corresponds to Re = 9,000 for this internal flow configuration.

Ghia, K. N.↗
NASA NTRS1987

Unsteady motion and transition to turbulence in developing curved duct flow

An experiment was performed to further the understanding of developing flows in curved ducts of square cross-section. Unlike most earlier works, attention was paid to investigating the time-dependent character of the motion. Mean and unsteady flow characteristics were determined using flow visualization and a laser-Doppler velocimeter. Only one velocity component, that aligned in the longitudinal (streamwise) coordinate direction, was measured. Notwithstanding, the time histories, autocorrelations and spectra derived reveal a time-periodic motion that becomes turbulent with increasing Reynolds number. The results are of intrinsic fundamental value and also illustrate the danger of imposing symmetry of the conservation equations on numerical solutions of this flow.

Arnal, M.↗
NASA NTRS1983

A turbulence model for three dimensional turbulent shear flows over curved rotating bodies

There exists currently considerable interest in the development of numerical procedures for solving the equations governing three-dimensional fluid flows. In particular, improved calculations of viscous flows on rotating bodies such a turbomachinery rotors are of great importance. The present investigation is mainly concerned with the analysis of the effect of rotation on the dissipation rate equation and the Reynolds stress equations. Attention is given to governing equations and modelling, algebraic Reynolds stress equations, a procedure for implementing the turbulence closure scheme, results for a model representative of centrifugal turbomachinery, and results for axial turbomachinery. The proposed turbulence model is valid for three-dimensional, rotating, and curved flows. The model has all the essential physics of turbulence, mean flow, rotation, and the curvature.

Galmes, J. M.↗
NASA NTRS1983

Study of asymptotic incompressible flow in curved ducts using a multi-grid technique

Asymptotic flows inside curved ducts of rectangular as well as polar cross sections have been analyzed using the Navier-Stokes equations in terms of the axial velocity and vorticity and the cross-flow stream function. Numerical solutions of the three second-order coupled elliptic partial differential equations governing this flow have been obtained using the multi-grid-SI scheme, to determine fine-grid results for configurations with strong secondary flow.

Ghia, K. N.↗
NASA NTRS1992

Some Aspects of Bifurcation Structure of Laminar Flow in Curved Ducts

A bifurcation study is made of laminar flow in curved ducts. The problem is formulated in a curvilinear coordinate system, and the governing equations, after orthogonal mapping is applied, are solved numerically by an iterative finite-difference method. Many computer runs were made with various duct cross-sections ranging from a circle to a square, to learn the transition of bifurcation structure with this change in cross-section and to reconcile the differences between them. In addition, a simpler technique is proposed to generate symmetric four-cell solutions in a circular pipe and a means is put forward to stabilize four-vortex structures in a complete cross-section.

Kao, Hsiao C.↗
NASA NTRS1990

The effects of streamline curvature and swirl on turbulent flows in curved ducts

A technique for improving the numerical predictions of turbulent flows with the effect of streamline curvature is developed. Separated flows, the flow in a curved duct, and swirling flows are examples of flow fields where streamline curvature plays a dominant role. A comprehensive literature review on the effect of streamline curvature was conducted. New algebraic formulations for the eddy viscosity incorporating the kappa-epsilon turbulence model are proposed to account for various effects of streamline curvature. The loci of flow reversal of the separated flows over various backward-facing steps are employed to test the capability of the proposed turbulence model in capturing the effect of local curvature. The inclusion of the effect of longitudinal curvature in the proposed turbulence model is validated by predicting the distributions of the static pressure coefficients in an S-bend duct and in 180 degree turn-around ducts. The proposed turbulence model embedded with transverse curvature modification is substantiated by predicting the decay of the axial velocities in the confined swirling flows. The numerical predictions of different curvature effects by the proposed turbulence models are also reported.

Cheng, Chih-Hsiung↗
NASA NTRS1990

Numerical study of turbulent secondary flows in curved ducts

The pressure driven, fully-developed turbulent flow of an incompressible viscous fluid in curved ducts of square-section is studied numerically by making use of a finite volume method. A nonlinear Kappa - Iota model is used to represent the turbulence. The results for both straight and curved ducts are presented. For the case of fully-developed turbulent flow in straight and curved ducts, the secondary flow is characterized by an eight-vortex structure for which the computed flowfield is shown to be in good agreement with available experimental data. The introduction of moderate curvature is shown to cause a substantial increase in the strength of the secondary flow and to change the secondary flow pattern to either a double-vortex or a four-vortex configuration.

Hur, N.↗
NASA NTRS1989

Numerical study of turbulent secondary flows in curved ducts

The pressure driven, fully-developed turbulent flow of an incompressible viscous fluid in curved ducts of square cross-section is studied numerically by making use of a finite volume method. A nonlinear Kappa - Iota model is used to represent the turbulence. The results for both straight and curved ducts are presented. For the case of fully-developed turbulent flow in straight ducts, the secondary flow is characterized by an eight-vortex structure for which the computed flowfield is shown to be in good agreement with available experimental data. The introduction of moderate curvature is shown to cause a substantial increase in the strength of the secondary flow and to change the secondary flow pattern to either a double-vortex or a four-vortex configuration.

Hur, N.↗
DOE OSTI2020

Meshfree methods on manifolds for hydrodynamic flows on curved surfaces: A Generalized Moving Least-Squares (GMLS) approach

We utilize generalized moving least squares (GMLS) to develop meshfree techniques for discretizing hydrodynamic flow problems on manifolds. We use exterior calculus to formulate incompressible hydrodynamic equations in the Stokesian regime and handle the divergence-free constraints via a generalized vector potential. This provides less coordinate-centric descriptions and enables the development of efficient numerical methods and splitting schemes for the fourth-order governing equations in terms of a system of second-order elliptic operators. Using a Hodge decomposition, we develop methods for manifolds having spherical topology. We show the methods exhibit high-order convergence rates for solving hydrodynamic flows on curved surfaces. The methods also provide general high-order approximations for the metric, curvature, and other geometric quantities of the manifold and associated exterior calculus operators. The approaches also can be utilized to develop high-order solvers for other scalar-valued and vector-valued problems on manifolds.

97 MATHEMATICS AND COMPUTING↗