Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fiber Composite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Carbon nanofibers based carbon–carbon composite fibers

Textile grade polyacrylonitrile (PAN) was used as a precursor material for carbon fiber preparation. E-beam irradiated polyacrylonitrile grafted carbon nanofibers were dispersed in polyacrylonitrile solution (dissolved in dimethyl formamide). Carbon nanofibers (CNF) infused polyacrylonitrile solution was wet spun on a lab-scale wet-spinning setup to form 50 to 70 µm diameter fibers with 3.2 wt.% CNF-PAN, 6.4 wt.% CNF-PAN, and neat PAN. Precursor fibers were characterized for thermal, mechanical and morphological properties using various techniques. Drawing the precursor fibers further enhanced polymer chain orientation and coalesced the voids, enhancing tensile strength and modulus by more than 150% compared to those of the undrawn fibers. Precursor composite fibers on carbonization showed enhanced strength, compared to that of pristine PAN fibers, by four times and stiffness by 14 times. The carbon–carbon composite fibers were further characterized with SEM/FIB, XRD and tensile strength. The property improvements were dependent on the uniform distribution of carbon nanofibers, and surface modification of carbon nanofibers further enabled their dispersion in the composite fibers. Furthermore, 3.2 wt.% CNFs in PAN fibers showed maximum improvement in properties compared to 6.4 wt.% CNF in PAN fibers, indicating that the property enhancements go through a maximum and then drop off due to challenge in getting uniform distribution of nanofibers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Radiation damage of a two-dimensional carbon fiber composite (CFC)

Carbon fiber composites (CFC) are, among other applications, already in use as low-impedance collimating elements for intercepting TeV-level protons machines, like the CERN Large Hadron Collider. Towards a comprehensive understanding of these materials’ properties and behavior, a series of radiation damage campaigns have been undertaken in order to quantitively investigate the response of AC-150 K CFC to high proton fluences. The CFCs dimensional changes, stability, micro-structural evolution, and structural integrity below and above 5 × 10 20 p/cm 2 fluence threshold were studied. The irradiating particles were protons of kinetic energies in the range of 130–200 MeV. The effects of the irradiation temperature (~90–180°C and 280–500°C) combined with the proton fluence on the dimensional stability and the microstructural evolution of this anisotropic two-dimensional composite structure were studied using precision dilatometry and X-ray diffraction. Our results shed light on the fluence-based limitations for these composite materials. Furthermore, we compare these results with reference unirradiated graphite, and we discuss the similarities and differences in the dimensional changes and post-irradiation annealing properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hygrothermal aging and recycling effects on mechanical and thermal properties of recyclable thermoplastic glass fiber composites

Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.

17 WIND ENERGY↗
DOE OSTI2021

Enhancing functionalities in carbon fiber composites by titanium dioxide nanoparticles

Carbon fiber composite's high specific strength makes it incredibly useful for structural applications. However, their low strain-to-failure can be problematic in structural applications that can potentially see high strain conditions or high fatigue cycles resulting in sudden, catastrophic failure. This is further complicated by damage manifesting within the composite thus not showing damage indicators on the surface. Therefore, monitoring the structural integrity and strain history of the composite in application by itself—while maintaining positive composite performance—is vital to ensure safe operation. In this study, a homogeneous dispersion of TiO 2 nanoparticles on carbon fiber is demonstrated to generate a piezoresistive carbon fiber polymer matrix composite with enhanced self-sensing capabilities. The nanoparticle-embedded composites also exhibited superior strength and damping potential compared to the nanoparticle-free composites. The apparent interlaminar shear strength increased by up to 15% and the damping loss factor increased by an average of 150% while the piezoresistive sensitivity increased by up to 180% with the addition of a small weight fraction of nanoparticles to the fiber surface. These results demonstrate an approach to simultaneously improve the sensing capabilities, damping behavior and mechanical strength of carbon fiber composites by simply adding nanoparticles in the fiber sizing using a commercially scalable deposition method.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Aluminum-fiber composites containing intermetallic phase at the matrix-fiber interface

A solid aluminum-fiber composite comprising: (i) an aluminum-containing matrix comprising elemental aluminum; (ii) coated or uncoated fibers embedded within said aluminum-containing matrix, wherein said fibers have a different composition than said aluminum-containing matrix and impart additional strength to said aluminum-containing matrix as compared to said aluminum-containing matrix in the absence of said fibers embedded therein; and (iii) an intermetallic layer present as an interface between each of said fibers and the aluminum-containing matrix, wherein said intermetallic layer has a composition different from said aluminum-containing matrix and said fibers, and said intermetallic layer contains at least one element that is also present in the aluminum-containing matrix and at least one element present in the fibers, whether from the coated or interior portion of the fibers. Methods of producing the above-described composite are also described.

Rios, Orlando↗
DOE OSTI2020

Markforged Continuous Fiber Composite Material Testing

Continuous fiber composite 3D printing promises to greatly expand the design space of polymer additive manufacturing (AM). A series of mechanical tests were performed to attempt to fully characterize the composite materials built from feedstock provided by the Markforged company. These tests included tensile, compression, Charpy impact, three point bending, coefficient of thermal expansion, and calorimetry tests. Specimens were prepared on the Mark Two 3D printer at LANL during the spring and summer of 2019. These samples were then shipped to New Mexico Institute of Mining and Technology’s Thermo-Mechanical Lab for testing during the summer and fall of 2019. Test data are reported and analyzed for each of the tests.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive Manufacturing of Self‐Sensing Carbon Fiber Composites

Carbon fiber-reinforced polymer (CFRP) composites have gained substantial attention across various industries owing to their exceptional mechanical properties and lightweight nature. The emergence of additive manufacturing technologies brings new opportunities to the industry, offering advantages such as design freedom, rapid prototyping, and customization. However, the fabrication of CFRP composites through 3D printing techniques poses challenges pertaining to low resolution and limitations in complex geometry realization. This work introduces digital light processing printing as a versatile, high-resolution method ideal for CFRP composite fabrication. Furthermore, the development and characterization of CFRP are focused on and the manipulation of mechanical properties through variations in matrix resins and fiber loadings is investigated, showcasing the versatility of CFRP composites for tailored applications. Additionally, the integration of self-sensing capabilities in CFRP structures is explored, which opens up opportunities for applications in smart components for automotive and structural health monitoring.

carbon fiber composites↗
DOE OSTI2021

Effect of the Segmental Structure of Thermoplastic Polyurethane (Hardness) on the Interfacial Adhesion of Textile-Grade Carbon Fiber Composites

In polymer composites, the fiber–matrix interface is primarily influenced by the surface treatment of the fibers and polymer morphology. Previous studies have investigated the effect of surface treatment of carbon fiber on the mechanical properties of the resulting composites. However, very few studies have explored the chemical structural modification of polymer effect on the fiber–matrix adhesion. In this work, the interfaces of soft thermoplastic polyurethane (S-TPU) and hard-segmented TPU (H-TPU) were investigated through surface, thermal, and mechanical characterization. A textile-grade carbon fiber (TCF) with 1% concentration of epoxy sizing (an emerging material for nonaerospace applications with 450 K filament tows) was used as a reinforcement to investigate the structure–property relationship at the interface. Atomic force microscopy results showed 39% higher surface roughness for S-TPU than for H-TPU. X-ray photoelectron spectroscopy results revealed a 550% increase in C=O content, which can provide multiple hydrogen bonding networks in H-TPU, and these C=O bonds can produce a strong chemical bond at the fiber–matrix interface. Additionally, dynamic mechanical analysis and differential scanning calorimetry results confirmed the presence of hydrogen bonding that enhances the cross-linked density by 232% in H-TPU compared to S-TPU. The improved mechanical properties of H-TPU composites, such as flexural, impact and tensile by 30, 50, and 130% compared to S-TPU composites, prove that the crystallinity and hydrogen bonding significantly increase the load bearing capacity due to the strong interface. The mechanical properties of TCF–TPU composites validate the formation of chemical bonds through a nucleophilic addition reaction at the interface and improve the bond strength of the composites. Thus, tailoring the polyurethane structure broadens the performance of segmented TPU in conjunction with TCF reinforcement, which has implications for cost-effective, high-strength composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crashworthiness of recycled carbon fiber composite sinusoidal structures at dynamic rates

Fiber reinforced polymer composites are finding applications in the automotive space for structurally critical applications including crash management. The use of recycled carbon fiber reinforcement can greatly reduce carbon emissions. In this study, recycled carbon fiber composites were manufactured into a self-supporting geometry using three matrices: polyphenylene sulfide (PPS), acrylonitrile butadiene styrene (ABS), and a structural epoxy, and subsequently crushed between flat platens at dynamic rates ranging from 4.6 to 9.1 ms -1 at temperatures in a range of -40°C to 80°C. Load-displacement data was used to evaluate their specific energy absorption, crush efficiency, and steady-state crush stress. Further, the energy absorption of the ABS composites was strongly sensitive to temperature, while the PPS composites exhibited strong crush efficiency dependence with both rate and temperature. The epoxy composites exhibited stable crush behavior at dynamic crush rates but exhibited a dramatic reduction in crush efficiency relative to quasi-static tests. The results of this study indicate that recycled fiber composites can achieve very high energy absorption levels (50–80kJkg -1 at room temperature) that make them an excellent alternative to more expensive and less environmentally friendly continuous virgin fiber laminates.

42 ENGINEERING↗
DOE OSTI2021

Recycling of natural fiber composites: Challenges and opportunities

Natural fibers have been widely used for reinforcing polymers attributed to their sustainable nature, excellent stiffness to weight ratio, biodegradability, and low cost compared with synthetic fibers like carbon or glass fibers. Thermoplastic composites offer an advantage of recyclability after their service life, but challenges and opportunities remain in the recycling of natural fiber reinforced polymer composites (NFRPCs). This article summarized the effects of reprocessing/recycling on the material properties of NFRPCs. The material properties considered include mechanical performance, thermal properties, hygroscopic behavior, viscoelasticity, degradation, and durability. NFRPCs can generally be recycled approximately 4–6 times until their thermomechanical properties change. After recycling 7 times, the tensile strength of NFRPCs can decrease by 17%, and the tensile modulus can decrease by 28%. The mitigation approaches to overcome degradation of material properties of NFRPCs such as adding functional additives and virgin plastics are also discussed. The main challenges in these approaches such as degradation and incompatibility are discussed, and an effort is made to provide a rationale for reprocessing/recyclability assessment. Finally, future applications of NFRPCs such as additive manufacturing and automotive part use are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Enhanced Interfacial Strength in Carbon Fiber Composites via Mussel‐Inspired Sizing Polymers

Composite materials possess a high strength-to-weight ratio. A key determinant of their mechanical performance is the interfacial strength between the fibers and the matrix. Sizing agents are commonly used to improve this interface by promoting better adhesion, though optimizing this interaction remains a significant challenge. Here, this study evaluates the use of poly(catechol-styrene) (PCS), a mussel-inspired sizing agent, to enhance fiber–matrix bonding in carbon fiber composites. Woven carbon fiber laminates were dip-coated with varying concentrations of PCS (0.05 and 0.1 wt%) and subsequently fabricated using vacuum-assisted resin transfer molding followed by compression molding. Interlaminar shear strength (ILSS) tests showed improvements of 4% and 8% for the 0.05% and 0.1% PCS treatments, respectively. These results indicate that PCS is effective in reinforcing interfacial adhesion, thereby improving the mechanical integrity of carbon fiber-reinforced composites.

Carbon fiber composites↗
DOE OSTI2023

Enhanced through-thickness electrical conductivity and lightning strike damage response of interleaved vertically aligned short carbon fiber composites

Through-thickness electrical conductivity of carbon fiber reinforced polymers (CFRPs) is a key characteristic that determines the severity of lighting strike-induced damage. Carbon Fibers (CFs) are inherently electrically conductive and therefore provide high conductivity in the direction of the fiber orientation. However, electrical conductivities through the thickness and orthogonal to the CF orientation in CFRPs are governed by the insulating polymer matrix present between CFs. Here, in this work, through the thickness alignment of short CFs in between layers of CFRP laminates is demonstrated to improve the through-thickness electrical conductivity. Composites with interleaved vertically aligned short CF fibers (<150 μm) will be referred as V-fiber composites hereafter. The effect of the V-fiber on the lightning strike damage is evaluated against an artificial lightning strike of 100 kA (modified waveform A of SAE ARP-5412B standard). The improved through-thickness electrical conductivity of CFRP laminates (1.15 S/cm) through vertical alignment of short CFs was compared to reference CFRP laminates (0.13 S/cm) and was found to dissipate the artificial lightning strike current more efficiently. The surface damage after the artificial lightning strike in the V-fiber composites was reduced to 12.69 cm 2 compared to the reference CFRP surface damage of 57.67 cm 2 , a 78% reduction. It was also demonstrated that Joule heat generated due to lightning strike on the composites was significantly less than the reference sample using infrared (IR) thermography. A high retention (up to 78%) of flexural properties (modulus and strength) was observed in V-fiber composites post lightning strike impact as compared to only 47% retention in the reference panel.

42 ENGINEERING↗
DOE OSTI2023

Silicon carbide fiber composite receiver tubes manufactured by PIP process

The performance of SiC fiber composites made by a polymer infiltration and pyrolysis (PIP) process was investigated. Two types of tubular composites were manufactured using Hi-Nicalon and Nicalon-CG silicon carbide fibers infiltrated with SMP10 silicon carbide matrix. The fiber content in both composites was about 25 vol.% with an average density of 2.39 g/cc. The tubular SiC composites showed stable solar absorptance and emittance of 0.97 and 0.91, respectively, at 800 °C. The composites were thermally shocked at 900, 1000, and 1100 °C with a waterjet simulating raindrops. As a result, the hoop tensile strength of the composites revealed no loss of mechanical strength due to the thermal shock experiments up to 1100 °C.

14 SOLAR ENERGY↗
DOE OSTI2022

Metal fiber composite additive manufacturing (MFC-AM) and composite structures formed by MFC-AM

In a metal fiber composite (MFC) additive manufacturing (AM) method, a layer of polymer structures is deposited using a fused filament fabrication (FFF) printer assembly comprising at least one nozzle. Subsequently, an MFC printer assembly is used to embed a continuous metal fiber into one or more of the polymer structures of the layer. The embedding is achieved by heating the metal fiber and applying pressure to the metal fiber using an embedding surface of the MFC printer assembly. The heated metal fiber melts polymer adjacent thereto, thereby allowing the pressure to embed the metal fiber into the polymer structure. Using the MFC-AM method, various composite structures can be formed, such as novel heat exchangers that may otherwise be difficult or impossible to fabricate via other manufacturing techniques.

Hymas, David M.↗
DOE OSTI2025

Graph neural networks for mechanical property prediction of 2D fiber composites

This work investigates the ability of graph neural networks (GNNs) to homogenize 2D fiber composite microstructures. We use different inhomogeneity and anisotropy indices to motivate and show that the Volume Elements (VEs) used in ML methods should ideally be far from their Representative Volume Element (RVE) size limit and, consequently, are notably anisotropic. Hence, training only the isotropic limit properties may not be acceptable. Another aspect is the need to normalize elastic stiffness values for ML, especially when high elastic contrast ratios are encountered between composite phases or in the material set. We introduce a normalization technique based on the mean-field method (MFM) to handle such high contrast ratios and train for the entire stiffness tensor. We show that the proposed GNN approaches exhibit high accuracy and efficiency compared to traditional methods and convolutional neural networks, utilizing unstructured graphs constructed from microstructure topology. Our model successfully predicts the stiffness tensor, peak strength under bulk damage, and brittle fracture initiation strength across diverse microstructure configurations while maintaining high accuracy even for extreme material contrasts and volume fractions. We also present a method to improve prediction accuracy for small dataset sizes using Voronoi partitioning.

Brittle strength↗
DOE OSTI2020

Direct observation on supersonic microprojectile penetration of carbon fiber composites with ultrafast synchrotron X-ray phase contrast imaging

High-speed penetration into carbon fiber composites is of fundamental importance to materials science and impact engineering, but research along this line suffers considerably from the lack of direct experimental observations. Here we investigate such penetration dynamics of a unidirectional carbon fiber reinforced epoxy (UCFRE) composite, with a combination of in situ, ultrafast, synchrotron phase contrast imaging and finite element (FE) analysis. The experiments yield the first direct observation on projectile trajectories and fiber-scale deformation and damage in the UCFRE composites during supersonic microprojectile penetration, for different fiber orientations (0 degrees - 90 degrees from the impact direction) and projectile velocities (600 - 850 m.s -1 ), at unprecedented temporal (~ 100 ps) and spatial (5 μm) resolutions. The maximum penetration depth decreases with increasing fiber orientation angles, as a result of anisotropic damage evolution in the composite sample. Strain localizations are prone to develop along a direction perpendicular to the fiber orientation, while the damage or cavity region, along the fiber direction. FE modeling with a three-dimensional Hashin criterion yields consistent projectile trajectory and cavity morphology with the experimental results. Finally, with increasing fiber orientation angles, damage analyses show a transition in the damage mode from fiber compression to matrix compression damage, in line with the increasing maximum penetration depth.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Formation of helices with controllable chirality in gel-fiber composites

While microscale helices with specified chirality are pervasive in biological systems, driving purely synthetic materials to self-organize into such useful structures remains a significant challenge. Through theory and simulations, we model the behavior of initially flat ribbons of gel-fiber composites and show that these materials self-organize into three-dimensional helices with the application of heat. We specifically focus on thermo-responsive gels, which shrink when heated to a point near the lower critical solubility temperature (LCST). Within the composite, regions of the LCST gel that lie far from the fibers can readily shrink in response to the increased temperature; however, near the fibers the network is inhibited from undergoing the heat-induced collapse. This competition between the constrained and the unconstrained regions of the heated sample plays a vital role in the structural evolution of the material. Additionally, we find that this dynamic process can be controlled through the careful placement of the fibers on the outer surface of the gel. We specifically identify fiber arrangements that lead to the formation of helical structures with controlled chirality. Moreover, we isolate scenarios where constraining the movement of one or both the free ends of the sample promotes and stabilizes the formation of helical structures with specified handedness. Such structurally tailored composites are useful for creating mechanically robust actuators, and “appendages” for soft robots that can controllably curl and uncurl with variations in temperature.

36 MATERIALS SCIENCE↗